| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
set_edid never wrote the new EDID to state->edid.edid, it was only
written to the hardware. Since get_edid returned state->edid.edid,
it was never returning the right EDID.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: added missing commit log]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The CSI controller can take raw data from the data bus and output it
directly to capture buffers. This can be used to support the JPEG media
bus format.
While the controller can report minimum and maximum bytes per line, it
has no way to report how many lines were captured in the last frame.
Thus, even when the on-bus data is framed correctly, we have no way to
accertain the actual amount of data captured, unless we scan the buffer
for JPEG EOI markers, or sequential zeros. For now we leave bytesused
alone, and leave it up to userspace applications to parse the data.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The CSI controller can take raw data from the data bus and output RGB565
format. The controller does not distinguish between RGB565 LE and BE.
Instead this is determined by the media bus format, i.e. the format or
order the sensor is sending data in.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
max_register is currently set to 0x1000. This is beyond the mapped
address range of the hardware, so attempts to dump the regmap from
debugfs would trigger a kernel exception.
Furthermore, the useful registers only occupy a small section at the
beginning of the full range. Change the value to 0x9c, the last known
register on the V3s and H3.
On the A31, the register range is extended to support additional
capture channels. Since this is not yet supported, ignore it for now.
Fixes: 5cc7522d8965 ("media: sun6i: Add support for Allwinner CSI V3s")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Document RZ/G2 support.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Document RZ/G1 and RZ/G2 support.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
drivers/media/platform/vsp1/vsp1_drm.c: drivers/media/platform/vsp1/vsp1_drm.c:336 vsp1_du_pipeline_setup_brx() error: we previously assumed 'pipe->brx' could be null (see line 244)
smatch missed that if pipe->brx was NULL, then later on it will be
set with a non-NULL value. But it is easier to just use the brx pointer
so smatch doesn't get confused.
Tested-on: Salvator-XS-ES2.0, Salvator-XS-M3N
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Tested-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The uvc driver uses this function to fill in bus_info for VIDIOC_QUERYCAP,
so use the same function when filling in the bus_info for the media device.
The current implementation only fills in part of the info. E.g. if the full
bus_info is usb-0000:01:00.0-1.4.2, then the media bus_info only has 1.4.2.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
drivers/media/usb/uvc/uvc_video.c: drivers/media/usb/uvc/uvc_video.c:1893 uvc_video_start_transfer() warn: argument 2 to %u specifier is cast from pointer
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Language improvements, fix entity naming, make pipeline a graph and move
device usage documentation to device documentation ipu3.rst.
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
CSI block in Allwinner A64 has similar features as like in H3,
but the default CSI_SCLK rate cannot work properly to drive the
connected sensor interface.
The tested mod cock rate is 300 MHz and BSP vfe media driver is also
using the same rate. Unfortunately there is no valid information about
clock rate in manual or any other sources except the BSP driver. so more
faith on BSP code, because same has tested in mainline.
So, add support for A64 CSI block by setting updated mod clock rate.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Allwinner A64 CSI is a single channel time-multiplexed BT.656
protocol interface.
Add separate compatible string for A64 since it require explicit
change in sun6i_csi driver to update default CSI_SCLK rate.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The extended-controls.rst file had become too big. Split it up: each
control class reference gets its own rst file, and this file just
describes the Extended Control API.
Each control class reference is also moved up one level into the
table of contents to make it easier to find e.g. the codec control
reference.
Finally I rearranged the order so that all camera-related control
classes are grouped together, ditto for codec/jpeg and fm-rx/tx.
The ext-ctrls-codec.rst is still pretty big and it is a candidate
to split up further in the future, possibly per codec.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The epoll function expects that whenever the poll file op is
called, the poll_wait function is also called. That didn't
always happen in dvb_demux_poll(), dvb_dvr_poll() and
dvb_ca_en50221_io_poll(). Fix this, otherwise epoll()
can timeout when it shouldn't.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The epoll function expects that whenever the poll file op is
called, the poll_wait function is also called. That didn't
always happen in videobuf_poll_stream(). Fix this, otherwise
epoll() would timeout when it shouldn't.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The v4l2_m2m_poll function didn't check whether q->error
was set for either of the two queues. Add support for this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The epoll function expects that whenever the poll file op is
called, the poll_wait function is also called. That didn't
always happen in v4l2_m2m_poll(). Fix this, otherwise
epoll() would timeout when it shouldn't.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The epoll function expects that whenever the poll file op is
called, the poll_wait function is also called. That didn't
always happen in v4l2_ctrl_poll(). Fix this, otherwise epoll()
would timeout when it shouldn't.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The epoll function expects that whenever the poll file op is
called, the poll_wait function is also called. That didn't
always happen in vb2_core_poll() and vb2_poll(). Fix this,
otherwise epoll() would timeout when it shouldn't.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Yi Qingliang <niqingliang2003@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The epoll function expects that whenever the poll file op is
called, the poll_wait function is also called. That didn't
always happen in media_request_poll(). Fix this, otherwise
epoll() would timeout when it shouldn't.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The epoll function expects that whenever the poll file op is
called, the poll_wait function is also called. That didn't
always happen in cec_poll(). Fix this, otherwise epoll()
would timeout when it shouldn't.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
If a stream is stopped, or if a USERPTR/DMABUF buffer is queued
backed by a different user address or dmabuf fd, then the timestamp
should be skipped by vb2_find_timestamp since the memory it refers
to is no longer valid.
So keep track of a 'copied_timestamp' state: it is set when the
timestamp is copied from an output to a capture buffer, and is
cleared when it is no longer valid.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The bool type is not recommended for use in structs, so replace these
by bitfields.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Buffers generated with YUV32 format seems to be incorrect, hence use
VUYA32 instead.
Changes from v1:
Add both formats VUYA32 and VUYX32 but associate only VUYX32 to the
output queue as the alpha channel of buffers is ignored on this queue.
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Enable vivid to make use of the following formats:
V4L2_PIX_FMT_AYUV32
V4L2_PIX_FMT_XYUV32
V4L2_PIX_FMT_VUYA32
V4L2_PIX_FMT_VUYX32
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Add support for the following formats to tpg:
V4L2_PIX_FMT_AYUV32
V4L2_PIX_FMT_XYUV32
V4L2_PIX_FMT_VUYA32
V4L2_PIX_FMT_VUYX32
Changes from v1:
Remove the duplicate case value
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The formats added in this patch include:
V4L2_PIX_FMT_AYUV32
V4L2_PIX_FMT_XYUV32
V4L2_PIX_FMT_VUYA32
V4L2_PIX_FMT_VUYX32
These formats enable the trasmission of alpha channel data to other
drivers and userspace applications in addition to YUV data. For
example, buffers generated by drivers in one of these formats
can be used by the Weston compositor to display as a texture or
flipped directly onto the overlay planes with the help of a DRM
driver.
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Without this, we get failures like this when the kernel attempts to
initialize a cx231xx device:
[16046.153653] cx231xx 3-1.2:1.1: New device Hauppauge Hauppauge Device @ 480 Mbps (2040:c200) with 6 interfaces
[16046.153900] cx231xx 3-1.2:1.1: can't change interface 3 alt no. to 3: Max. Pkt size = 0
[16046.153907] cx231xx 3-1.2:1.1: Identified as Hauppauge USB Live 2 (card=9)
[16046.154350] i2c i2c-11: Added multiplexed i2c bus 13
[16046.154379] i2c i2c-11: Added multiplexed i2c bus 14
[16046.267194] cx25840 10-0044: cx23102 A/V decoder found @ 0x88 (cx231xx #0-0)
[16048.424551] cx25840 10-0044: loaded v4l-cx231xx-avcore-01.fw firmware (16382 bytes)
[16048.463224] cx231xx 3-1.2:1.1: v4l2 driver version 0.0.3
[16048.567878] cx231xx 3-1.2:1.1: Registered video device video2 [v4l2]
[16048.568001] cx231xx 3-1.2:1.1: Registered VBI device vbi0
[16048.568419] cx231xx 3-1.2:1.1: audio EndPoint Addr 0x83, Alternate settings: 3
[16048.568425] cx231xx 3-1.2:1.1: video EndPoint Addr 0x84, Alternate settings: 5
[16048.568431] cx231xx 3-1.2:1.1: VBI EndPoint Addr 0x85, Alternate settings: 2
[16048.568436] cx231xx 3-1.2:1.1: sliced CC EndPoint Addr 0x86, Alternate settings: 2
[16048.568448] usb 3-1.2: couldn't get decoder output pad for V4L I/O
[16048.568453] cx231xx 3-1.2:1.1: V4L2 device vbi0 deregistered
[16048.568579] cx231xx 3-1.2:1.1: V4L2 device video2 deregistered
[16048.569001] cx231xx: probe of 3-1.2:1.1 failed with error -22
Likely a regession since Commit 9d6d20e652c0
("media: v4l2-mc: switch it to use the new approach to setup pipelines")
(v4.19-rc1-100-g9d6d20e652c0), which introduced the use of
PAD_SIGNAL_DV within v4l2_mc_create_media_graph().
This also modifies cx25840 to remove the VBI pad, matching the action
taken in Commit 092a37875a22 ("media: v4l2: remove VBI output pad").
Fixes: 9d6d20e652c0 ("media: v4l2-mc: switch it to use the new approach to setup pipelines")
Cc: stable@vger.kernel.org
Signed-off-by: Cody P Schafer <dev@codyps.com>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
There is a spelling mistake in a fmdbg debug message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
media_device_cleanup() wasn't called, which caused a small
memory leak.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
When the media device registration fails, don't call media_device_unregister
since the device was never actually registered.
When removing the module also call media_device_cleanup() to avoid a memory leak.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
This patch makes the SoC camera framework as well as effectively the few
remaining sensor drivers depend on BROKEN, rendering it uncompileable
without changes in Kconfig.
The purpose is to leave the code around if someone wishes to convert the
drivers to the modern day V4L2 sub-device framework without having to go
to see development history in git.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Move the mt9t031 driver to the soc_camera directory in the media staging
tree.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Move the imx074 driver to the soc_camera directory in the media staging
tree.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The SoC camera framework has no functional drivers left, something that
has not changed for years. Move the leftovers to the staging tree.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
There is a V4L2 sub-device sensor driver for the rj45n1.
As there is already another driver, remove the SoC camera one.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
There is a V4L2 sub-device sensor driver for the mt9m001.
There is already a non-soc_camera driver. So, remove the SoC camera
one.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
This addresses the below TODO item, no function related changes:
- Prefix imgu for all public APIs, i.e. change ipu3_v4l2_register() to
imgu_v4l2_register(). (Sakari)
The changes were obtained by applying the following perl script
to driver code under drivers/staging/media/ipu3/.
perl -pi.back -e 's/ipu3_(?!uapi)/imgu_/g;'
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
According to the ov5640 specification (2.7 power up sequence), host can
access the sensor's registers 20ms after reset. Trying to access them
before leads to undefined behavior and result in sporadic initialization
errors.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The ov5640_try_frame_interval operation updates the FPS as per user
input based on default ov5640_frame_rate, OV5640_30_FPS which is failed
to update when user trigger 15fps.
So, initialize the default ov5640_frame_rate to OV5640_15_FPS so-that
it can satisfy to update all fps.
Fixes: 5a3ad937bc78 ("media: ov5640: Make the return rate type more explicit")
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The register value lists for all the supported resolution settings all
include a register address/value pair for setting the JPEG compression
mode. With the exception of 1080p (which sets mode 2), all resolutions
use mode 3.
The only difference between mode 2 and mode 3 is that mode 2 may have
padding data on the last line, while mode 3 does not add padding data.
As these register values were from dumps of running systems, and the
difference between the modes is quite small, using mode 3 for all
configurations should be OK.
[Sakari Ailus: Align OV5640_REG_JPG_MODE_SELECT register naming.]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
When compression is turned on, the on-bus data is framed according to
the compression mode, and the height and width set in VFIFO_VSIZE and
VFIFO_HSIZE. If these are not updated correctly, the sensor will send
data framed in a manner unexpected by the capture interface, such as
having more bytes per line than expected, and having the extra data
dropped. This ultimately results in corrupted data.
Set the two values when the media bus is configured for JPEG data,
meaning the sensor would be in JPEG mode.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The OV5640 driver currently supports a static color bar pattern with a
small vertical gamma gradient. The hardware also supports a color square
pattern, as well as having a rolling bar for dynamic sequences.
Add three more test patterns:
- color bars with a rolling bar (but without the gamma gradient)
- static color squares
- color squares with a rolling bar
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The transparent feature for test patterns blends the test pattern with
an actual captured image. This makes the result non-static, subject to
changes in the sensor's field of view.
Test patterns should be predictable and deterministic, even if they are
dynamic patterns. Disable the transparent feature of the test pattern.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The OV5640 can generate many types of test patterns, some with
additional modifiers, such as a rolling bar, or gamma gradients.
Add the bit definitions for all bits in the test pattern register,
and use them to compose the values to be written to the register.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The OV5640 has many options for generating test patterns. Unfortunately
there is only one V4L2 control for it. Thus the driver would need to
list some or all combinations.
Move the test_pattern_menu list before the ov5640_set_ctrl_test_pattern
function that programs the hardware. This would allow us to add a
matching list of values to program into the hardware, while keeping the
two lists together for ease of maintenance.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The ADV748X_PAGE_WAIT is a fake page to insert arbitrary delays in the
register tables.
Its only usage was removed, so we can remove the handling and simplify
the code.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The ADV748x is currently reset by writting a small table of registers to
the device.
The table lacks documentation and contains magic values to perform the
actions, including using a fake register address to introduce a delay
loop.
Remove the table, and convert to code, documenting the purpose of the
specific writes along the way.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
When the adv748x driver is informed about a link being created from HDMI or
AFE to a CSI-2 TX output, the 'link_setup()' callback is invoked. Make
sure to implement proper routing management at link setup time, to route
the selected video stream to the desired TX output.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Both the AFE and HDMI s_stream routines (adv748x_afe_s_stream() and
adv748x_hdmi_s_stream()) have to enable the CSI-2 TX they are streaming video
data to.
With the introduction of dynamic routing between HDMI and AFE entities to
TXA, the video stream sink needs to be set at run time, and not statically
selected as the s_stream functions are currently doing.
To fix this, store a reference to the active CSI-2 TX sink for both HDMI and
AFE sources, and operate on it when starting/stopping the stream.
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
Tim Harvey
Chen-Yu Tsai
Fabrizio Castro
Hans Verkuil
Hans Verkuil
Yong Zhi
Jagan Teki
Vivek Kasireddy
Cody P Schafer
Colin Ian King
Sakari Ailus
Loic Poulain
Kieran Bingham
Jacopo Mondi