aboutsummaryrefslogtreecommitdiffstats
path: root/CREDITS (unfollow)
AgeCommit message (Collapse)AuthorFilesLines
2018-11-14i40e: Use correct shift for VLAN priorityRichard Rodriguez1-2/+2
When using port VLAN, for VFs, and setting priority bits, the device was sending out incorrect priority bits, and also setting the CFI bit incorrectly. To fix this, changed shift and mask bit definition for this function, to use the correct ones. Signed-off-by: Richard Rodriguez <richard.rodriguez@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-11-14virtchnl: Fix off by one errorAlice Michael1-2/+2
When calculating the valid length for a VIRTCHNL_OP_ENABLE_CHANNELS message, we accidentally allowed messages with one extra virtchnl_channel_info structure on the end. This happened due to an off by one error, because we forgot that valid_len already accounted for one virtchnl_channel_info structure, so we need to subtract one from the num_tc value. Signed-off-by: Alice Michael <alice.michael@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-11-14virtchnl: white space and reorderAlice Michael1-3/+3
White space change. Move the check on the virtchnl_vsi_queue_config_info struct to be close to the struct like all the other similar checks. This keeps it clearer and easier to read. Signed-off-by: Alice Michael <alice.michael@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-11-14i40e: always set ks->base.speed in i40e_get_settings_link_upJacob Keller1-0/+1
In i40e_get_settings_link_up, set ks->base.speed to SPEED_UNKNOWN in the case where we don't know the link speed. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-11-14i40e: don't restart nway if autoneg not supportedMitch Williams1-5/+5
On link types that do not support autoneg, we cannot attempt to restart nway negotiation. This results in a dead link that requires a power cycle to remedy. Fix this by saving off the autoneg state and checking this value before we try to restart nway. Signed-off-by: Mitch Williams <mitch.a.williams@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-11-14i40e: Allow disabling FW LLDP on X722 devicesPatryk Małek4-15/+17
This patch allows disabling FW LLDP agent on X722 devices. It also changes a source of information for this feature from pf->hw_features to pf->hw.flags which are set in i40e_init_adminq. Signed-off-by: Patryk Małek <patryk.malek@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-11-14i40e: update driver versionAlice Michael1-2/+2
The version numbers have not been kept up to date and this is an effort to ammend that. Signed-off-by: Alice Michael <alice.michael@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-11-14i40e: Protect access to VF control methodsJan Sokolowski2-5/+60
A scenario has been found in which simultaneous addition/removal and modification of VF's might cause unstable behaviour, up to and including kernel panics. Protect the methods that create/modify/destroy VF's by locking them behind an atomically set bit in PF status bitfield. Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-11-14i40e: Replace strncpy with strlcpy to ensure null terminationPatryk Małek2-8/+8
Using strncpy allows destination buffer to be not null terminated after the copying takes place. strlcpy ensures that's not the case by explicitly setting last element in the buffer as '\0'. Signed-off-by: Patryk Małek <patryk.malek@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-11-14i40e: Add capability flag for stopping FW LLDPKrzysztof Galazka3-1/+10
Add HW capability flag to indicate that firmware supports stopping LLDP agent. This feature has been added in FW API 1.7 for XL710 devices and 1.6 for X722. Also raise expected minor version number for X722 FW API to 6. Signed-off-by: Krzysztof Galazka <krzysztof.galazka@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-11-14i40e: Use a local variable for readabilityJan Sokolowski1-2/+2
Use a local variable to make the code a bit more readable. Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-11-14i40e: Replace spin_is_locked() with lockdepLance Roy1-2/+1
lockdep_assert_held() is better suited to checking locking requirements, since it won't get confused when someone else holds the lock. This is also a step towards possibly removing spin_is_locked(). Signed-off-by: Lance Roy <ldr709@gmail.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-11-14net: aquantia: add support of rx-vlan-filter offloadDmitry Bogdanov7-18/+197
Since it uses the same NIC table as rx flow vlan filter therefore rx-flow vlan filter accepts only vlans that present on the interface in case of rx-vlan-filter is on. Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com> Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-14net: aquantia: add ethertype and PCP to rx flow filtersDmitry Bogdanov5-4/+133
L2 EtherType filters allows to filter packet by EtherType field or both EtherType and User Priority (PCP) field of 802.1Q. UserPriority (vlan) parameter must be accompanied by mask 0x1FFF. That is to distinguish VLAN filter from L2 Ethertype filter with UserPriority since both User Priority and VLAN ID are passed in the same 'vlan' parameter. Example: To add a filter that directs IP4 packess of priority 3 to queue 3: ethtool -N <ethX> flow-type ether proto 0x800 vlan 0x600 m 0x1FFF \ action 3 loc 16 Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com> Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-14net: aquantia: add vlan id to rx flow filtersDmitry Bogdanov7-3/+151
The VLAN filter (VLAN id) is compared against 16 filters. VLAN id must be accompanied by mask 0xF000. That is to distinguish VLAN filter from L2 Ethertype filter with UserPriority since both User Priority and VLAN ID are passed in the same 'vlan' parameter. Flow type may be any as it is not matched for VLAN filter. Due to fixed order of the rules in the NIC, the location 0-15 are reserved for vlan filters. Example: To add a rule that directs packets from VLAN 2001 to queue 5: ethtool -N <ethX> flow-type ip4 vlan 2001 m 0xF000 action 5 loc 0 Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com> Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-14net: aquantia: add support of L3/L4 ntuple filtersDmitry Bogdanov5-3/+284
Add support of L3/L4 5-tuple {protocol, src-ip, dst-ip, src-port, dst-port} filters. Mask is not supported. Src-port and dst-port are only compared for TCP/UDP/SCTP packets. Both IPv4 and IPv6 are supported. The supported actions are the drop and the queue assignment. Due to fixed order of the rules in the NIC, the location 32-39 are reserved for L3/L4 5-tuple filters. The locations 32 and 36 are reserved for IPv6 filters. Examples: sudo ethtool -N eth0 flow-type ip6 src-ip 2001:db8:0:f101::2 \ dst-ip 2001:db8:0:f101::5 action -1 loc 36 sudo ethtool -N eth0 flow-type udp4 src-ip 10.0.0.4 \ dst-ip 10.0.0.7 src-port 2000 dst-port 2001 action 2 loc 32 Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com> Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-14net: aquantia: add infrastructure for ntuple rulesDmitry Bogdanov8-1/+501
Add infrastructure to support ntuple filter configuration. Add rule, remove rule, reapply on interface up. Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com> Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-14net: aquantia: add rx-flow filter definitionsDmitry Bogdanov3-17/+275
Add missing register definitions and the functions accessing them related to rx-flow filters. Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com> Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-13net: ethernet: ti: cpsw: allow vlan tagged packets to be timestampedIvan Khoronzhuk1-2/+3
Allow vlan tagged packets to be timestamped, as no any restrictions for this. Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-13net: ethernet: ti: cpts: move enable/disable flags outside of cpts moduleIvan Khoronzhuk4-77/+41
Each slave has it's own receive timestamp filter. But cpts rx/tx timestamp enable flags are used to allow ts retrieve only for one user. This limitation causes data path redundancy and setting overlap if cpsw module is in dual-mac mode for instance. If rx ts is enabled only for one port - the second interface must expect every incoming packet to be PTP packet w/o absolutely any reason, and if it's PTP - do unneeded stuff, as rx filter for second port is not set and cpts fifo is not supposed to contain appropriate ts event. That's not correct. So, to fix control overlap and avoid redundant CPU cycles, the patch splits rx/tx ts enable flags between network devices. After the patch, PTP timestamping still should be used for only one port (or PTP id counter has to be different for both ports as cpts IP is common). Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-13net: ethernet: ti: cpts: purge staled skbs from txqIvan Khoronzhuk1-2/+24
The overflow event is running with 1 jiffy in case if txq is not empty, but it can be emptied completely only if next tx event consumes skb or deletes staled skb from the txq. In case of staled skb, that can happen for some unpredictable reason (the ts event was lost or timed out), the overflow event can be generated quite long time consuming CPU w/o reason before next tx event happens. To avoid it, purge txq before increasing overflow event rate. Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-13net: ethernet: ti: cpts: correct debug for expired txq skbIvan Khoronzhuk1-3/+1
The msgtype and seqid that is smth that belongs to event for comparison but not for staled txq skb. Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-12net: phy: check if advertising is zero using linkmode_emptyColin Ian King1-1/+1
A recent change modified variable advertising from a u32 to a link mode array and left the u32 zero comparison, so essential we now have an array being compared to null which is not the intention. Fix this by using the call to linkmode_empty to check if advertising is all zero. Detected by CoverityScan, CID#1475424 ("Array compared against 0") Fixes: 3c1bcc8614db ("net: ethernet: Convert phydev advertize and supported from u32 to link mode") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-12sctp: process sk_reuseport in sctp_get_port_localXin Long2-14/+36
When socks' sk_reuseport is set, the same port and address are allowed to be bound into these socks who have the same uid. Note that the difference from sk_reuse is that it allows multiple socks to listen on the same port and address. Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-12sctp: add sock_reuseport for the sock in __sctp_hash_endpointXin Long6-11/+85
This is a part of sk_reuseport support for sctp. It defines a helper sctp_bind_addrs_check() to check if the bind_addrs in two socks are matched. It will add sock_reuseport if they are completely matched, and return err if they are partly matched, and alloc sock_reuseport if all socks are not matched at all. It will work until sk_reuseport support is added in sctp_get_port_local() in the next patch. v1->v2: - use 'laddr->valid && laddr2->valid' check instead as Marcelo pointed in sctp_bind_addrs_check(). Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-12sctp: do reuseport_select_sock in __sctp_rcv_lookup_endpointXin Long1-28/+41
This is a part of sk_reuseport support for sctp, and it selects a sock by the hashkey of lport, paddr and dport by default. It will work until sk_reuseport support is added in sctp_get_port_local() in the next patch. v1->v2: - define lport as __be16 instead of __be32 as Marcelo pointed in __sctp_rcv_lookup_endpoint(). Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-11net: phy: marvell: remove set but not used variable 'pause'YueHaibing1-2/+0
Fixes gcc '-Wunused-but-set-variable' warning: drivers/net/phy/marvell.c: In function 'm88e1510_config_init': drivers/net/phy/marvell.c:850:7: warning: variable 'pause' set but not used [-Wunused-but-set-variable] It not used any more after commit 3c1bcc8614db ("net: ethernet: Convert phydev advertize and supported from u32 to link mode") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-11Linux 4.20-rc2Linus Torvalds1-1/+1
2018-11-11PCI: add USR vendor id and use it in r8169 and w6692 driverHeiner Kallweit3-4/+3
The PCI vendor id of U.S. Robotics isn't defined in pci_ids.h so far, only ISDN driver w6692 has a private definition. Move the definition to pci_ids.h and use it in the r8169 driver too. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-11net_sched: sch_fq: add dctcp-like markingEric Dumazet2-0/+24
Similar to 80ba92fa1a92 ("codel: add ce_threshold attribute") After EDT adoption, it became easier to implement DCTCP-like CE marking. In many cases, queues are not building in the network fabric but on the hosts themselves. If packets leaving fq missed their Earliest Departure Time by XXX usec, we mark them with ECN CE. This gives a feedback (after one RTT) to the sender to slow down and find better operating mode. Example : tc qd replace dev eth0 root fq ce_threshold 2.5ms Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-11tcp: tsq: no longer use limit_output_bytes for paced flowsEric Dumazet3-5/+6
FQ pacing guarantees that paced packets queued by one flow do not add head-of-line blocking for other flows. After TCP GSO conversion, increasing limit_output_bytes to 1 MB is safe, since this maps to 16 skbs at most in qdisc or device queues. (or slightly more if some drivers lower {gso_max_segs|size}) We still can queue at most 1 ms worth of traffic (this can be scaled by wifi drivers if they need to) Tested: # ethtool -c eth0 | egrep "tx-usecs:|tx-frames:" # 40 Gbit mlx4 NIC tx-usecs: 16 tx-frames: 16 # tc qdisc replace dev eth0 root fq # for f in {1..10};do netperf -P0 -H lpaa24,6 -o THROUGHPUT;done Before patch: 27711 26118 27107 27377 27712 27388 27340 27117 27278 27509 After patch: 37434 36949 36658 36998 37711 37291 37605 36659 36544 37349 Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-11tcp: get rid of tcp_tso_should_defer() dependency on HZ/jiffiesEric Dumazet1-2/+5
tcp_tso_should_defer() first heuristic is to not defer if last send is "old enough". Its current implementation uses jiffies and its low granularity. TSO autodefer performance should not rely on kernel HZ :/ After EDT conversion, we have state variables in nanoseconds that can allow us to properly implement the heuristic. This patch increases TSO chunk sizes on medium rate flows, especially when receivers do not use GRO or similar aggregation. It also reduces bursts for HZ=100 or HZ=250 kernels, making TCP behavior more uniform. Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-11tcp: refine tcp_tso_should_defer() after EDT adoptionEric Dumazet1-3/+4
tcp_tso_should_defer() last step tries to check if the probable next ACK packet is coming in less than half rtt. Problem is that the head->tstamp might be in the future, so we need to use signed arithmetics to avoid overflows. Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-11tcp: do not try to defer skbs with eor mark (MSG_EOR)Eric Dumazet1-0/+4
Applications using MSG_EOR are giving a strong hint to TCP stack : Subsequent sendmsg() can not append more bytes to skbs having the EOR mark. Do not try to TSO defer suchs skbs, there is really no hope. Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-11tcp: minor optimization in tcp ack fast path processingYafang Shao1-3/+4
Bitwise operation is a little faster. So I replace after() with using the flag FLAG_SND_UNA_ADVANCED as it is already set before. In addtion, there's another similar improvement in tcp_cwnd_reduction(). Cc: Joe Perches <joe@perches.com> Suggested-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Yafang Shao <laoar.shao@gmail.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-11act_mirred: clear skb->tstamp on redirectEric Dumazet2-10/+2
If sch_fq is used at ingress, skbs that might have been timestamped by net_timestamp_set() if a packet capture is requesting timestamps could be delayed by arbitrary amount of time, since sch_fq time base is MONOTONIC. Fix this problem by moving code from sch_netem.c to act_mirred.c. Fixes: fb420d5d91c1 ("tcp/fq: move back to CLOCK_MONOTONIC") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-11net: dsa: mv88e6xxx: Fix clearing of stats countersAndrew Lunn1-0/+2
The mv88e6161 would sometime fail to probe with a timeout waiting for the switch to complete an operation. This operation is supposed to clear the statistics counters. However, due to a read/modify/write, without the needed mask, the operation actually carried out was more random, with invalid parameters, resulting in the switch not responding. We need to preserve the histogram mode bits, so apply a mask to keep them. Reported-by: Chris Healy <Chris.Healy@zii.aero> Fixes: 40cff8fca9e3 ("net: dsa: mv88e6xxx: Fix stats histogram mode") Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-11net: dsa: mv88e6xxx: Add support for SERDES on ports 2-8 for 6390XAndrew Lunn3-11/+25
The 6390X family has 8 SERDES interfaces. When ports 9 and 10 are not using all their SERDES interfaces, the unused ones can be assigned to ports 2-8. Add support for interrupts from SERDES interfaces connected to these lower ports. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-11net: dsa: mv88e6xxx: Default ports 9/10 6390X CMODE to 1000BaseXAndrew Lunn1-3/+6
The 6390X family has 8 SERDES interfaces. This allows ports 9 and 10 to support up to 10Gbps using 4 SERDES interfaces. However, when lower speeds are used, which need fewer SERDES interfaces, the unused SERDES interfaces can be used by ports 2-8. The hardware defaults to ports 9 and 10 having all 4 SERDES interfaces assigned to them. This only gets changed when the interface is configured after what the SFP supports has been determined, or the 10G PHY completes auto-neg. For hardware designs which limit ports 9 and 10 to one or two SERDES interfaces, and place SFPs on the lower interfaces, this is too late. Those ports with SFP should not wait until ports 9/10 are up in order to get access to the SERDES interface. So change the default configuration when the driver is initialised. Configure ports 9 and 10 to 1000BaseX, so they use a single SERDES interface, freeing up the others. They can steal them back if they need them. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-11net: dsa: mv88e6xxx: Differentiate between 6390 and 6390X cmodesAndrew Lunn3-2/+22
The X family variants support additional ports modes, for 10G operation, which the non-X variants don't have. Add a port_set_cmode() for non-X variants to enforce this. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-11net: dsa: mv88e6xxx: Group cmode ops togetherAndrew Lunn1-3/+3
Move .port_set_cmode next to .port_get_cmode. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-11net: phy: Add support for resolving 5G and 2.5G autonegAndrew Lunn1-0/+8
Now that 2.5G and 5G can be represented in phydev->advertising and phydev->lp_advertising, add these two links modes as possible resolutions to auto negotiation. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-11net: phy: Add more link modes to the settings tableAndrew Lunn1-4/+158
Now that PHYs and MAC can support more than 32 bit masks, add link modes which are > 31 to the PHY settings table. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-11net: phy: Fixup kerneldoc markup.Andrew Lunn1-1/+1
Add missing markup for function parameters Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-11net: phy: Convert u32 phydev->lp_advertising to linkmodeAndrew Lunn10-41/+72
Convert phy drivers to report the link partner advertised modes using a linkmode bitmap. This allows them to report the higher speeds which don't fit in a u32. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-11net: ethernet: Convert phydev advertize and supported from u32 to link modeAndrew Lunn39-330/+536
There are a few MAC/PHYs combinations which now support > 1Gbps. These may need to make use of link modes with bits > 31. Thus their supported PHY features or advertised features cannot be implemented using the current bitmap in a u32. Convert to using a linkmode bitmap, which can support all the currently devices link modes, and is future proof as more modes are added. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-11net: phy: remove states PHY_STARTING and PHY_PENDINGHeiner Kallweit2-27/+2
Both states aren't used. Most likely they result from an idea that never materialized. So remove them. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-11tipc: fix link re-establish failureJon Maloy1-4/+7
When a link failure is detected locally, the link is reset, the flag link->in_session is set to false, and a RESET_MSG with the 'stopping' bit set is sent to the peer. The purpose of this bit is to inform the peer that this endpoint just is going down, and that the peer should handle the reception of this particular RESET message as a local failure. This forces the peer to accept another RESET or ACTIVATE message from this endpoint before it can re-establish the link. This again is necessary to ensure that link session numbers are properly exchanged before the link comes up again. If a failure is detected locally at the same time at the peer endpoint this will do the same, which is also a correct behavior. However, when receiving such messages, the endpoints will not distinguish between 'stopping' RESETs and ordinary ones when it comes to updating session numbers. Both endpoints will copy the received session number and set their 'in_session' flags to true at the reception, while they are still expecting another RESET from the peer before they can go ahead and re-establish. This is contradictory, since, after applying the validation check referred to below, the 'in_session' flag will cause rejection of all such messages, and the link will never come up again. We now fix this by not only handling received RESET/STOPPING messages as a local failure, but also by omitting to set a new session number and the 'in_session' flag in such cases. Fixes: 7ea817f4e832 ("tipc: check session number before accepting link protocol messages") Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-11documentation of some IP/ICMP snmp countersyupeng2-0/+223
The snmp_counter.rst explains the meanings of snmp counters. It also provides a set of experiments (only 1 for this initial patch), combines the experiments' resutls and the snmp counters' meanings. This is an initial path, only explains a part of IP/ICMP counters and provide a simple ping test. Signed-off-by: yupeng <yupeng0921@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-11-11tipc: improve broadcast retransmission algorithmLUU Duc Canh2-46/+14
Currently, the broadcast retransmission algorithm is using the 'prev_retr' field in struct tipc_link to time stamp the latest broadcast retransmission occasion. This helps to restrict retransmission of individual broadcast packets to max once per 10 milliseconds, even though all other criteria for retransmission are met. We now move this time stamp to the control block of each individual packet, and remove other limiting criteria. This simplifies the retransmission algorithm, and eliminates any risk of logical errors in selecting which packets can be retransmitted. Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: LUU Duc Canh <canh.d.luu@dektech.com.au> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.