Age | Commit message (Collapse) | Author | Files | Lines |
|
Since we didn't get any new reports from users about wrong settings
of pad ownership, there is no point to spam kernel log with it. Thus,
drop level from warning to debug.
Also, modify format to be in align with the rest restore helpers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Refactor restoring GPI_IE registers by using an introduced helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Refactor restoring HOSTSW_OWN registers by using an introduced helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Deduplicate restoring PADCFGx registers by using a common helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Keeping the IRQ chip definition static shares it with multiple instances
of the GPIO chip in the system. This is bad and now we get this warning
from GPIO library:
"detected irqchip that is shared with multiple gpiochips: please fix the driver."
Hence, move the IRQ chip definition from being driver static into the struct
intel_pinctrl. So a unique IRQ chip is used for each GPIO chip instance.
This patch is heavily based on the attachment to the bug by Christoph Marz.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=202543
Fixes: 6e08d6bbebeb ("pinctrl: Add Intel Cherryview/Braswell pin controller support")
Depends-on: 83b9dc11312f ("pinctrl: cherryview: Associate IRQ descriptors to irqdomain")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
One spelling mistake is being fixed: benerate -> generate.
It is a complimentary fix to the commit 505485a83c55 ("pinctrl:
cherryview fixed typo in comment").
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Commit 03c4749dd6c7 ("gpio / ACPI: Drop unnecessary ACPI GPIO to Linux
GPIO translation") has made the cherryview gpio numbers sparse, to get
a 1:1 mapping between ACPI pin numbers and gpio numbers in Linux.
This has greatly simplified things, but the code setting the
irq_valid_mask was not updated for this, so the valid mask is still in
the old "compressed" numbering with the gaps in the pin numbers skipped,
which is wrong as irq_valid_mask needs to be expressed in gpio numbers.
This results in the following error on devices using pin 24 (0x0018) on
the north GPIO controller as an ACPI event source:
[ 0.422452] cherryview-pinctrl INT33FF:01: Failed to translate GPIO to IRQ
This has been reported (by email) to be happening on a Caterpillar CAT T20
tablet and I've reproduced this myself on a Medion Akoya e2215t 2-in-1.
This commit uses the pin number instead of the compressed index into
community->pins to clear the correct bits in irq_valid_mask for GPIOs
using GPEs for interrupts, fixing these errors and in case of the
Medion Akoya e2215t also fixing the LID switch not working.
Cc: stable@vger.kernel.org
Fixes: 03c4749dd6c7 ("gpio / ACPI: Drop unnecessary ACPI GPIO to Linux GPIO translation")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
When consumer requests a pin, in order to be on the safest side,
we switch it first to GPIO mode followed by immediate transition
to the input state. Due to posted writes it's luckily to be a single
I/O transaction.
However, if firmware or boot loader already configures the pin
to the GPIO mode, user expects no glitches for the requested pin.
We may check if the pin is pre-configured and leave it as is
till the actual consumer toggles its state to avoid glitches.
Fixes: 7981c0015af2 ("pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support")
Depends-on: f5a26acf0162 ("pinctrl: intel: Initialize GPIO properly when used through irqchip")
Cc: stable@vger.kernel.org
Cc: fei.yang@intel.com
Reported-by: Oliver Barta <oliver.barta@aptiv.com>
Reported-by: Malin Jonsson <malin.jonsson@ericsson.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
|
|
If we always compile the get_break_insn_length inline function we can
remove the ifdefs and let dead code elimination take care of the warn
branch that is now unreadable because the report_bug stub always
returns BUG_TRAP_TYPE_BUG.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
|
nbd requires socket families to support the shutdown method so the nbd
recv workqueue can be woken up from its sock_recvmsg call. If the socket
does not support the callout we will leave recv works running or get hangs
later when the device or module is removed.
This adds a check during socket connection/reconnection to make sure the
socket being passed in supports the needed callout.
Reported-by: syzbot+24c12fa8d218ed26011a@syzkaller.appspotmail.com
Fixes: e9e006f5fcf2 ("nbd: fix max number of supported devs")
Tested-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This driver is using regulator_get_optional() to handle all the supplies
that it handles, and only ever enables and disables all supplies en masse
without ever doing any other configuration of the device to handle missing
power. These are clear signs that the API is being misused - it should only
be used for supplies that may be physically absent from the system and in
these cases the hardware usually needs different configuration if the
supply is missing. Instead use normal regualtor_get(), if the supply is
not described in DT then the framework will substitute a dummy regulator in
so no special handling is needed by the consumer driver.
In the case of the PHY regulator the handling in the driver is a hack to
deal with integrated PHYs; the supplies are only optional in the sense
that that there's some confusion in the code about where they're bound to.
From a code point of view they function exactly as normal supplies so can
be treated as such. It'd probably be better to model this by instantiating
a PHY object for integrated PHYs.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
We hit the following warning in production
print_req_error: I/O error, dev nbd0, sector 7213934408 flags 80700
------------[ cut here ]------------
refcount_t: underflow; use-after-free.
WARNING: CPU: 25 PID: 32407 at lib/refcount.c:190 refcount_sub_and_test_checked+0x53/0x60
Workqueue: knbd-recv recv_work [nbd]
RIP: 0010:refcount_sub_and_test_checked+0x53/0x60
Call Trace:
blk_mq_free_request+0xb7/0xf0
blk_mq_complete_request+0x62/0xf0
recv_work+0x29/0xa1 [nbd]
process_one_work+0x1f5/0x3f0
worker_thread+0x2d/0x3d0
? rescuer_thread+0x340/0x340
kthread+0x111/0x130
? kthread_create_on_node+0x60/0x60
ret_from_fork+0x1f/0x30
---[ end trace b079c3c67f98bb7c ]---
This was preceded by us timing out everything and shutting down the
sockets for the device. The problem is we had a request in the queue at
the same time, so we completed the request twice. This can actually
happen in a lot of cases, we fail to get a ref on our config, we only
have one connection and just error out the command, etc.
Fix this by checking cmd->status in nbd_read_stat. We only change this
under the cmd->lock, so we are safe to check this here and see if we've
already error'ed this command out, which would indicate that we've
completed it as well.
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
We already do this for the most part, except in timeout and clear_req.
For the timeout case we take the lock after we grab a ref on the config,
but that isn't really necessary because we're safe to touch the cmd at
this point, so just move the order around.
For the clear_req cause this is initiated by the user, so again is safe.
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
We currently assume that submissions from the sqthread are successful,
and if IO polling is enabled, we use that value for knowing how many
completions to look for. But if we overflowed the CQ ring or some
requests simply got errored and already completed, they won't be
available for polling.
For the case of IO polling and SQTHREAD usage, look at the pending
poll list. If it ever hits empty then we know that we don't have
anymore pollable requests inflight. For that case, simply reset
the inflight count to zero.
Reported-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
We currently use the ring values directly, but that can lead to issues
if the application is malicious and changes these values on our behalf.
Created in-kernel cached versions of them, and just overwrite the user
side when we update them. This is similar to how we treat the sq/cq
ring tail/head updates.
Reported-by: Pavel Begunkov <asml.silence@gmail.com>
Reviewed-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Relax qspi pins slew-rate to minimize peak currents.
Fixes: 844030057339 ("ARM: dts: stm32: add flash nor support on stm32mp157c eval board")
Link: https://lore.kernel.org/r/20191025130122.11407-1-alexandre.torgue@st.com
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
io_ring_submit() finalises with
1. io_commit_sqring(), which releases sqes to the userspace
2. Then calls to io_queue_link_head(), accessing released head's sqe
Reorder them.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
io_sq_thread() processes sqes by 8 without considering links. As a
result, links will be randomely subdivided.
The easiest way to fix it is to call io_get_sqring() inside
io_submit_sqes() as do io_ring_submit().
Downsides:
1. This removes optimisation of not grabbing mm_struct for fixed files
2. It submitting all sqes in one go, without finer-grained sheduling
with cq processing.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
There is a bug, where failed linked requests are returned not with
specified @user_data, but with garbage from a kernel stack.
The reason is that io_fail_links() uses req->user_data, which is
uninitialised when called from io_queue_sqe() on fail path.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Support for the kernel as Xen 32-bit PV guest will soon be removed.
Issue a warning when booted as such.
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
|
|
Modify plic_init() to skip .dts interrupt contexts other
than supervisor external interrupt.
The .dts entry for plic may specify multiple interrupt contexts.
For example, it may assign two entries IRQ_M_EXT and IRQ_S_EXT,
in that order, to the same interrupt controller. This patch
modifies plic_init() to skip the IRQ_M_EXT context since
IRQ_S_EXT is currently the only supported context.
If IRQ_M_EXT is not skipped, plic_init() will report "handler
already present for context" when it comes across the IRQ_S_EXT
context in the next iteration of its loop.
Without this patch, .dts would have to be edited to replace the
value of IRQ_M_EXT with -1 for it to be skipped.
Signed-off-by: Alan Mikhak <alan.mikhak@sifive.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Paul Walmsley <paul.walmsley@sifive.com> # arch/riscv
Link: https://lkml.kernel.org/r/1571933503-21504-1-git-send-email-alan.mikhak@sifive.com
|
|
There's a deadlock that is possible and can easily be seen with
a test where multiple readers open/read/close of the same file
and a disruption occurs causing reconnect. The deadlock is due
a reader thread inside cifs_strict_readv calling down_read and
obtaining lock_sem, and then after reconnect inside
cifs_reopen_file calling down_read a second time. If in
between the two down_read calls, a down_write comes from
another process, deadlock occurs.
CPU0 CPU1
---- ----
cifs_strict_readv()
down_read(&cifsi->lock_sem);
_cifsFileInfo_put
OR
cifs_new_fileinfo
down_write(&cifsi->lock_sem);
cifs_reopen_file()
down_read(&cifsi->lock_sem);
Fix the above by changing all down_write(lock_sem) calls to
down_write_trylock(lock_sem)/msleep() loop, which in turn
makes the second down_read call benign since it will never
block behind the writer while holding lock_sem.
Signed-off-by: Dave Wysochanski <dwysocha@redhat.com>
Suggested-by: Ronnie Sahlberg <lsahlber@redhat.com>
Reviewed--by: Ronnie Sahlberg <lsahlber@redhat.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
|
|
Currently the code assumes that if a file info entry belongs
to lists of open file handles of an inode and a tcon then
it has non-zero reference. The recent changes broke that
assumption when putting the last reference of the file info.
There may be a situation when a file is being deleted but
nothing prevents another thread to reference it again
and start using it. This happens because we do not hold
the inode list lock while checking the number of references
of the file info structure. Fix this by doing the proper
locking when doing the check.
Fixes: 487317c99477d ("cifs: add spinlock for the openFileList to cifsInodeInfo")
Fixes: cb248819d209d ("cifs: use cifsInodeInfo->open_file_lock while iterating to avoid a panic")
Cc: Stable <stable@vger.kernel.org>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
When the client hits reconnect it iterates over the mid
pending queue marking entries for retry and moving them
to a temporary list to issue callbacks later without holding
GlobalMid_Lock. In the same time there is no guarantee that
mids can't be removed from the temporary list or even
freed completely by another thread. It may cause a temporary
list corruption:
[ 430.454897] list_del corruption. prev->next should be ffff98d3a8f316c0, but was 2e885cb266355469
[ 430.464668] ------------[ cut here ]------------
[ 430.466569] kernel BUG at lib/list_debug.c:51!
[ 430.468476] invalid opcode: 0000 [#1] SMP PTI
[ 430.470286] CPU: 0 PID: 13267 Comm: cifsd Kdump: loaded Not tainted 5.4.0-rc3+ #19
[ 430.473472] Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
[ 430.475872] RIP: 0010:__list_del_entry_valid.cold+0x31/0x55
...
[ 430.510426] Call Trace:
[ 430.511500] cifs_reconnect+0x25e/0x610 [cifs]
[ 430.513350] cifs_readv_from_socket+0x220/0x250 [cifs]
[ 430.515464] cifs_read_from_socket+0x4a/0x70 [cifs]
[ 430.517452] ? try_to_wake_up+0x212/0x650
[ 430.519122] ? cifs_small_buf_get+0x16/0x30 [cifs]
[ 430.521086] ? allocate_buffers+0x66/0x120 [cifs]
[ 430.523019] cifs_demultiplex_thread+0xdc/0xc30 [cifs]
[ 430.525116] kthread+0xfb/0x130
[ 430.526421] ? cifs_handle_standard+0x190/0x190 [cifs]
[ 430.528514] ? kthread_park+0x90/0x90
[ 430.530019] ret_from_fork+0x35/0x40
Fix this by obtaining extra references for mids being retried
and marking them as MID_DELETED which indicates that such a mid
has been dequeued from the pending list.
Also move mid cleanup logic from DeleteMidQEntry to
_cifs_mid_q_entry_release which is called when the last reference
to a particular mid is put. This allows to avoid any use-after-free
of response buffers.
The patch needs to be backported to stable kernels. A stable tag
is not mentioned below because the patch doesn't apply cleanly
to any actively maintained stable kernel.
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Reviewed-and-tested-by: David Wysochanski <dwysocha@redhat.com>
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
Remove the following warning:
drivers/i2c/busses/i2c-stm32f7.c:315:
warning: cannot understand function prototype:
'struct stm32f7_i2c_spec i2c_specs[] =
Replace a comment starting with /** by simply /* to avoid having
it interpreted as a kernel-doc comment.
Fixes: aeb068c57214 ("i2c: i2c-stm32f7: add driver")
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
When in slave mode, an arbitration loss (ARLO) may be detected before the
slave had a chance to detect the stop condition (STOPF in ISR).
This is seen when two master + slave adapters switch their roles. It
provokes the i2c bus to be stuck, busy as SCL line is stretched.
- the I2C_SLAVE_STOP event is never generated due to STOPF flag is set but
don't generate an irq (race with ARLO irq, STOPIE is masked). STOPF flag
remains set until next master xfer (e.g. when STOPIE irq get unmasked).
In this case, completion is generated too early: immediately upon new
transfer request (then it doesn't send all data).
- Some data get stuck in TXDR register. As a consequence, the controller
stretches the SCL line: the bus gets busy until a future master transfer
triggers the bus busy / recovery mechanism (this can take time... and
may never happen at all)
So choice is to let the STOPF being detected by the slave isr handler,
to properly handle this stop condition. E.g. don't mask IRQs in error
handler, when the slave is running.
Fixes: 60d609f30de2 ("i2c: i2c-stm32f7: Add slave support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The slave-interface documentation [1] states "the bus driver should
transmit the first byte" upon I2C_SLAVE_READ_REQUESTED slave event:
- 'val': backend returns first byte to be sent
The driver currently ignores the 1st byte to send on this event.
[1] https://www.kernel.org/doc/Documentation/i2c/slave-interface
Fixes: 60d609f30de2 ("i2c: i2c-stm32f7: Add slave support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Since commit abf4923e97c3 ("i2c: mediatek: disable zero-length transfers
for mt8183"), there is a NULL pointer dereference for all the SoCs
that don't have any quirk. mtk_i2c_functionality is not checking that
the quirks pointer is not NULL before starting to use it.
This commit add a call to i2c_check_quirks which will check whether
the quirks pointer is set, and if so will check if the IP has the
NO_ZERO_LEN quirk.
Fixes: abf4923e97c3 ("i2c: mediatek: disable zero-length transfers for mt8183")
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Cengiz Can <cengiz@kernel.wtf>
Reviewed-by: Hsin-Yi Wang <hsinyi@chromium.org>
Tested-by: Ulrich Hecht <uli@fpond.eu>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
On a system without Single VMOVP support (say GITS_TYPER.VMOVP == 0),
we will map vPEs only on ITSs that will actually control interrupts
for the given VM. And when moving a vPE, the VMOVP command will be
issued only for those ITSs.
But when issuing VMOVPs we seemed fail to present the exact ITSList
to ITSs who are actually included in the synchronization operation.
The its_list_map we're currently using includes all ITSs in the system,
even though some of them don't have the corresponding vPE mapping at all.
Introduce get_its_list() to get the per-VM its_list_map, to indicate
which ITSs have vPE mappings for the given VM, and use this map as
the expected ITSList when building VMOVP. This is hopefully a performance
gain not to do some synchronization with those unsuspecting ITSs.
And initialize the whole command descriptor to zero at beginning, since
the seq_num and its_list should be RES0 when GITS_TYPER.VMOVP == 1.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1571802386-2680-1-git-send-email-yuzenghui@huawei.com
|
|
gfs2 and gfs2meta share an ->init_fs_context function which allocates an
args structure stored in fc->fs_private. gfs2 registers a ->free
function to free this memory when the fs_context is cleaned up, but
there was not one registered for gfs2meta, causing a leak.
Register a ->free function for gfs2meta. The existing gfs2_fc_free
function does what we need.
Reported-by: syzbot+c2fdfd2b783754878fb6@syzkaller.appspotmail.com
Fixes: 1f52aa08d12f ("gfs2: Convert gfs2 to fs_context")
Signed-off-by: Andrew Price <anprice@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
|
|
Part 3 from this series [1] was not merged due to wrong splitting
and breaks mt6323 pmic on bananapi-r2
dmesg prints this line and at least switch is not initialized on bananapi-r2
mt6397 1000d000.pwrap:mt6323: unsupported chip: 0x0
this patch contains only the probe-changes and chip_data structs
from original part 3 by Hsin-Hsiung Wang
[1] https://patchwork.kernel.org/project/linux-mediatek/list/?series=164155
Fixes: a4872e80ce7d ("mfd: mt6397: Extract IRQ related code from core driver")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
build_restore_pagemask() will restore the value of register $1/$at when
its restore_scratch argument is non-zero, and aims to do so by filling a
branch delay slot. Commit 0b24cae4d535 ("MIPS: Add missing EHB in mtc0
-> mfc0 sequence.") added an EHB instruction (Execution Hazard Barrier)
prior to restoring $1 from a KScratch register, in order to resolve a
hazard that can result in stale values of the KScratch register being
observed. In particular, P-class CPUs from MIPS with out of order
execution pipelines such as the P5600 & P6600 are affected.
Unfortunately this EHB instruction was inserted in the branch delay slot
causing the MFC0 instruction which performs the restoration to no longer
execute along with the branch. The result is that the $1 register isn't
actually restored, ie. the TLB refill exception handler clobbers it -
which is exactly the problem the EHB is meant to avoid for the P-class
CPUs.
Similarly build_get_pgd_vmalloc() will restore the value of $1/$at when
its mode argument equals refill_scratch, and suffers from the same
problem.
Fix this by in both cases moving the EHB earlier in the emitted code.
There's no reason it needs to immediately precede the MFC0 - it simply
needs to be between the MTC0 & MFC0.
This bug only affects Cavium Octeon systems which use
build_fast_tlb_refill_handler().
Signed-off-by: Paul Burton <paulburton@kernel.org>
Fixes: 0b24cae4d535 ("MIPS: Add missing EHB in mtc0 -> mfc0 sequence.")
Cc: Dmitry Korotin <dkorotin@wavecomp.com>
Cc: stable@vger.kernel.org # v3.15+
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
|
|
The sequence number of the timeout req (req->sequence) indicate the
expected completion request. Because of each timeout req consume a
sequence number, so the sequence of each timeout req on the timeout
list shouldn't be the same. But now, we may get the same number (also
incorrect) if we insert a new entry before the last one, such as submit
such two timeout reqs on a new ring instance below.
req->sequence
req_1 (count = 2): 2
req_2 (count = 1): 2
Then, if we submit a nop req, req_2 will still timeout even the nop req
finished. This patch fix this problem by adjust the sequence number of
each reordered reqs when inserting a new entry.
Signed-off-by: zhangyi (F) <yi.zhang@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The sequence number of reqs on the timeout_list before the timeout req
should be adjusted in io_timeout_fn(), because the current timeout req
will consumes a slot in the cq_ring and cq_tail pointer will be
increased, otherwise other timeout reqs may return in advance without
waiting for enough wait_nr.
Signed-off-by: zhangyi (F) <yi.zhang@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
There are cases where it isn't always safe to block for submission,
even if the caller asked to wait for events as well. Revert the
previous optimization of doing that.
This reverts two commits:
bf7ec93c644cb
c576666863b78
Fixes: c576666863b78 ("io_uring: optimize submit_and_wait API")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The vectors span more than one byte, so mark them as arrays.
Fixes the following build error when building when using GCC 8.3:
In file included from ./include/linux/string.h:19,
from ./include/linux/bitmap.h:9,
from ./include/linux/cpumask.h:12,
from ./arch/mips/include/asm/processor.h:15,
from ./arch/mips/include/asm/thread_info.h:16,
from ./include/linux/thread_info.h:38,
from ./include/asm-generic/preempt.h:5,
from ./arch/mips/include/generated/asm/preempt.h:1,
from ./include/linux/preempt.h:81,
from ./include/linux/spinlock.h:51,
from ./include/linux/mmzone.h:8,
from ./include/linux/bootmem.h:8,
from arch/mips/bcm63xx/prom.c:10:
arch/mips/bcm63xx/prom.c: In function 'prom_init':
./arch/mips/include/asm/string.h:162:11: error: '__builtin_memcpy' forming offset [2, 32] is out of the bounds [0, 1] of object 'bmips_smp_movevec' with type 'char' [-Werror=array-bounds]
__ret = __builtin_memcpy((dst), (src), __len); \
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/mips/bcm63xx/prom.c:97:3: note: in expansion of macro 'memcpy'
memcpy((void *)0xa0000200, &bmips_smp_movevec, 0x20);
^~~~~~
In file included from arch/mips/bcm63xx/prom.c:14:
./arch/mips/include/asm/bmips.h:80:13: note: 'bmips_smp_movevec' declared here
extern char bmips_smp_movevec;
Fixes: 18a1eef92dcd ("MIPS: BMIPS: Introduce bmips.h")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
|
|
Change my email address, and add more Spreadtrum SC27xx series PMIC
drivers to maintain.
Link: https://lore.kernel.org/r/a48483d13243450ecf3b777d49e741b6367f2c6b.1571881956.git.baolin.wang@linaro.org
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Remove various not required ifdefs and externs.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
|
Using CONFIG_SPARSEMEM_VMEMMAP instead of CONFIG_SPARSEMEM to fix
following build issue.
riscv64-linux-ld: arch/riscv/mm/init.o: in function 'vmemmap_populate':
init.c:(.meminit.text+0x8): undefined reference to 'vmemmap_populate_basepages'
Cc: Logan Gunthorpe <logang@deltatee.com>
Fixes: d95f1a542c3d ("RISC-V: Implement sparsemem")
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
|
With CONFIG_SPARSEMEM and !CONFIG_SPARSEMEM_VMEMMAP,
arch/riscv/include/asm/pgtable.h: In function ‘mk_pte’:
include/asm-generic/memory_model.h:64:14: error: implicit declaration of function ‘page_to_section’; did you mean ‘present_section’? [-Werror=implicit-function-declaration]
int __sec = page_to_section(__pg); \
^~~~~~~~~~~~~~~
Fixed by changing mk_pte() from inline function to macro.
Cc: Logan Gunthorpe <logang@deltatee.com>
Fixes: d95f1a542c3d ("RISC-V: Implement sparsemem")
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
[paul.walmsley@sifive.com: fixed checkpatch errors]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
|
Failed to compile Fedora/RISCV kernel (5.4-rc3+) with sparsemem enabled:
fs/proc/kcore.c: In function 'read_kcore':
fs/proc/kcore.c:510:8: error: implicit declaration of function 'kern_addr_valid'; did you mean 'virt_addr_valid'? [-Werror=implicit-function-declaration]
510 | if (kern_addr_valid(start)) {
| ^~~~~~~~~~~~~~~
| virt_addr_valid
Looking at other architectures I don't see kern_addr_valid being guarded by
CONFIG_FLATMEM.
Fixes: d95f1a542c3d ("RISC-V: Implement sparsemem")
Signed-off-by: David Abdurachmanov <david.abdurachmanov@sifive.com>
Tested-by: David Abdurachmanov <david.abdurachmanov@sifive.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
|
Commit d698a388146c ("of: reserved-memory: ignore disabled memory-region
nodes") added an early return in of_reserved_mem_device_init_by_idx(), but
didn't call of_node_put() on a device_node whose ref-count was incremented
in the call to of_parse_phandle() preceding the early exit.
Fixes: d698a388146c ("of: reserved-memory: ignore disabled memory-region nodes")
Signed-off-by: Chris Goldsworthy <cgoldswo@codeaurora.org>
Cc: stable@vger.kernel.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
In unittest_data_add, a copy buffer is created via kmemdup. This buffer
is leaked if of_fdt_unflatten_tree fails. The release for the
unittest_data buffer is added.
Fixes: b951f9dc7f25 ("Enabling OF selftest to run without machine's devicetree")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Frank Rowand <frowand.list@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Fix the errors in the RiscV CPU DT schema:
Documentation/devicetree/bindings/riscv/cpus.example.dt.yaml: cpu@0: 'timebase-frequency' is a required property
Documentation/devicetree/bindings/riscv/cpus.example.dt.yaml: cpu@1: 'timebase-frequency' is a required property
Documentation/devicetree/bindings/riscv/cpus.example.dt.yaml: cpu@0: compatible:0: 'riscv' is not one of ['sifive,rocket0', 'sifive,e5', 'sifive,e51', 'sifive,u54-mc', 'sifive,u54', 'sifive,u5']
Documentation/devicetree/bindings/riscv/cpus.example.dt.yaml: cpu@0: compatible: ['riscv'] is too short
Documentation/devicetree/bindings/riscv/cpus.example.dt.yaml: cpu@0: 'timebase-frequency' is a required property
The DT spec allows for 'timebase-frequency' to be in 'cpu' or 'cpus' node
and RiscV requires it in /cpus node, so make it disallowed in cpu
nodes.
Fixes: 4fd669a8c487 ("dt-bindings: riscv: convert cpu binding to json-schema")
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: linux-riscv@lists.infradead.org
Acked-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The last time Gregory and Brian did a review was sometime around 2015,
since then, they have not been active for ARCH_BRCMSTB changes.
Following the position of other maintainers and Harald Welte's position
here:
[1] http://laforge.gnumonks.org/blog/20180307-mchardy-gpl/
remove both of them.
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Recent changes modified the function arguments of
thread_group_sample_cputime() and task_cputimers_expired(), but forgot to
update the comments. Fix it up.
[ tglx: Changed the argument name of task_cputimers_expired() as the pointer
points to an array of samples. ]
Fixes: b7be4ef1365d ("posix-cpu-timers: Switch thread group sampling to array")
Fixes: 001f7971433a ("posix-cpu-timers: Make expiry checks array based")
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/1571643852-21848-1-git-send-email-wang.yi59@zte.com.cn
|
|
Include the timekeeping.h header to get the declaration of the
sched_clock_{suspend,resume} functions. Fixes the following sparse
warnings:
kernel/time/sched_clock.c:275:5: warning: symbol 'sched_clock_suspend' was not declared. Should it be static?
kernel/time/sched_clock.c:286:6: warning: symbol 'sched_clock_resume' was not declared. Should it be static?
Signed-off-by: Ben Dooks (Codethink) <ben.dooks@codethink.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20191022131226.11465-1-ben.dooks@codethink.co.uk
|
|
A recent commit removed the NULL pointer check from the clock_getres()
implementation causing a test case to fault.
POSIX requires an explicit NULL pointer check for clock_getres() aside of
the validity check of the clock_id argument for obscure reasons.
Add it back for both 32bit and 64bit.
Note, this is only a partial revert of the offending commit which does not
bring back the broken fallback invocation in the the 32bit compat
implementations of clock_getres() and clock_gettime().
Fixes: a9446a906f52 ("lib/vdso/32: Remove inconsistent NULL pointer checks")
Reported-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1910211202260.1904@nanos.tec.linutronix.de
|
|
When doing an out of tree build with O=, the nsdeps script constructs
the absolute pathname of the module source file so that it can insert
MODULE_IMPORT_NS statements in the right place. However, ${srctree}
contains an unescaped path to the source tree, which, when used in a sed
substitution, makes sed complain:
++ sed 's/[^ ]* *//home/jeyu/jeyu-linux\/&/g'
sed: -e expression #1, char 12: unknown option to `s'
The sed substitution command 's' ends prematurely with the forward
slashes in the pathname, and sed errors out when it encounters the 'h',
which is an invalid sed substitution option. To avoid escaping forward
slashes ${srctree}, we can use '|' as an alternative delimiter for
sed instead to avoid this error.
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Matthias Maennich <maennich@google.com>
Tested-by: Matthias Maennich <maennich@google.com>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
|