| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull ARM SoC i.MX DT changes from Olof Johansson:
"This branch contains of devicetree changes for the Freescale i.MX
platform.
The base patch of the branch changes the format of the dts files to a
slightly different format that makes it easier to do derivative board
definitions, but it also introduces a lot of churn in the process
since every line of the file is touched.
On top of that are a handful of the regular changes; enabling more
boards as DT-based instead of legacy board files (mx25pdk), enabling
another driver for devicetree and thus adding bindings (onewire), etc.
I'm not happy about the churn, and will likely not take it for other
platforms in the future."
* tag 'late-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
ARM: dts: add dtsi for imx6q and imx6dl
ARM: dts: rename imx6q.dtsi to imx6qdl.dtsi
ARM: dts: i.MX6: Add regulator delay support
ARM: dts: Add device tree entry for onewire master on i.MX53
ARM: i.MX53: Add clocks for i.mx53 onewire master.
W1: Add device tree support to MXC onewire master.
ARM: imx: enable imx6q-cpufreq support
ARM: dts: Add apf51 basic support
ARM i.MX6: change mxs usbphy clock usage
ARM: dts: imx6q: Remove silicon version from SDMA firmware
ARM i.MX53: dts: add oftree for MBa53 baseboard
ARM i.MX53: add dts for the TQ tqma53 module
ARM: dts: imx53: pinctrl update
ARM i.MX51 babbage: Add keypad support
ARM: dts: imx: Add imx51 KPP entry
ARM: dts: imx25-karo-tx25: Put status entry in the end
ARM: mx25pdk: Add device tree support
ARM: dts: imx: use nodes label in board dts
ARM: dts: add missing imx dtb targets
ARM: boot: dts: Add an entry for imx27-pdk.dtb
...
|
|
Pull ARM SoC-specific updates from Arnd Bergmann:
"This is a larger set of new functionality for the existing SoC
families, including:
- vt8500 gains support for new CPU cores, notably the Cortex-A9 based
wm8850
- prima2 gains support for the "marco" SoC family, its SMP based
cousin
- tegra gains support for the new Tegra4 (Tegra114) family
- socfpga now supports a newer version of the hardware including SMP
- i.mx31 and bcm2835 are now using DT probing for their clocks
- lots of updates for sh-mobile
- OMAP updates for clocks, power management and USB
- i.mx6q and tegra now support cpuidle
- kirkwood now supports PCIe hot plugging
- tegra clock support is updated
- tegra USB PHY probing gets implemented diffently"
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (148 commits)
ARM: prima2: remove duplicate v7_invalidate_l1
ARM: shmobile: r8a7779: Correct TMU clock support again
ARM: prima2: fix __init section for cpu hotplug
ARM: OMAP: Consolidate OMAP USB-HS platform data (part 3/3)
ARM: OMAP: Consolidate OMAP USB-HS platform data (part 1/3)
arm: socfpga: Add SMP support for actual socfpga harware
arm: Add v7_invalidate_l1 to cache-v7.S
arm: socfpga: Add entries to enable make dtbs socfpga
arm: socfpga: Add new device tree source for actual socfpga HW
ARM: tegra: sort Kconfig selects for Tegra114
ARM: tegra: enable ARCH_REQUIRE_GPIOLIB for Tegra114
ARM: tegra: Fix build error w/ ARCH_TEGRA_114_SOC w/o ARCH_TEGRA_3x_SOC
ARM: tegra: Fix build error for gic update
ARM: tegra: remove empty tegra_smp_init_cpus()
ARM: shmobile: Register ARM architected timer
ARM: MARCO: fix the build issue due to gic-vic-to-irqchip move
ARM: shmobile: r8a7779: Correct TMU clock support
ARM: mxs_defconfig: Select CONFIG_DEVTMPFS_MOUNT
ARM: mxs: decrease mxs_clockevent_device.min_delta_ns to 2 clock cycles
ARM: mxs: use apbx bus clock to drive the timers on timrotv2
...
|
|
Pull ARM SoC cleanups from Arnd Bergmann:
"A large number of cleanups, all over the platforms. This is dominated
largely by the Samsung platforms (s3c, s5p, exynos) and a few of the
others moving code out of arch/arm into more appropriate subsystems.
The clocksource and irqchip drivers are now abstracted to the point
where platforms that are already cleaned up do not need to even
specify the driver they use, it can all get configured from the device
tree as we do for normal device drivers. The clocksource changes
basically touch every single platform in the process.
We further clean up the use of platform specific header files here,
with the goal of turning more of the platforms over to being
"multiplatform" enabled, which implies that they cannot expose their
headers to architecture independent code any more.
It is expected that no functional changes are part of the cleanup.
The overall reduction in total code lines is mostly the result of
removing broken and obsolete code."
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (133 commits)
ARM: mvebu: correct gated clock documentation
ARM: kirkwood: add missing include for nsa310
ARM: exynos: move exynos4210-combiner to drivers/irqchip
mfd: db8500-prcmu: update resource passing
drivers/db8500-cpufreq: delete dangling include
ARM: at91: remove NEOCORE 926 board
sunxi: Cleanup the reset code and add meaningful registers defines
ARM: S3C24XX: header mach/regs-mem.h local
ARM: S3C24XX: header mach/regs-power.h local
ARM: S3C24XX: header mach/regs-s3c2412-mem.h local
ARM: S3C24XX: Remove plat-s3c24xx directory in arch/arm/
ARM: S3C24XX: transform s3c2443 subirqs into new structure
ARM: S3C24XX: modify s3c2443 irq init to initialize all irqs
ARM: S3C24XX: move s3c2443 irq code to irq.c
ARM: S3C24XX: transform s3c2416 irqs into new structure
ARM: S3C24XX: modify s3c2416 irq init to initialize all irqs
ARM: S3C24XX: move s3c2416 irq init to common irq code
ARM: S3C24XX: Modify s3c_irq_wake to use the hwirq property
ARM: S3C24XX: Move irq syscore-ops to irq-pm
clocksource: always define CLOCKSOURCE_OF_DECLARE
...
|
|
mvebu cleanup vor v3.9 round3
- fix typo in mvebu clokc gating documentation.
* tag 'cleanup_for_v3.9_round3' of git://git.infradead.org/users/jcooper/linux:
ARM: mvebu: correct gated clock documentation
|
|
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
This mxs usbphy is only needs to be on after system boots
up, and software never needs to control it anymore.
Meanwhile, usbphy's parent needs to be notified if usb
is suspend or not. So we design below mxs usbphy usage:
- usbphy1_gate and usbphy2_gate:
Their parents are dummy clock, we only needs to enable
it after system boots up.
- usbphy1 and usbphy2
Usage reserved bit for this clock, in that case, the refcount
will be updated, but without hardware changing.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
From Stephen Warren:
ARM: tegra: Common Clock Framework rework
Tegra already supports the common clock framework, but had issues:
1) The clock driver was located in arch/arm/mach-tegra/ rather than
drivers/clk/.
2) A single "Tegra clock" type was implemented, rather than separate
clock types for PLL, mux, divider, ... type in HW.
3) Clock lookups by device drivers were still driven by device name
and connection ID, rather than through device tree.
This pull request solves all three issues. This required some DT changes
to add clocks properties, and driver changes to request clocks more
"correctly". Finally, this rework allows all AUXDATA to be removed from
Tegra board files, and various duplicate clock lookup entries to be
removed from the driver.
This pull request is based on the previous pull request, with tag
tegra-for-3.9-cleanup.
* tag 'tegra-for-3.9-soc-ccf' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra: (31 commits)
clk: tegra30: remove unused TEGRA_CLK_DUPLICATE()s
clk: tegra20: remove unused TEGRA_CLK_DUPLICATE()s
ARM: tegra30: remove auxdata
ARM: tegra20: remove auxdata
ASoC: tegra: remove auxdata
staging: nvec: remove use of clk_get_sys
ARM: tegra: paz00: add clock information to DT
ARM: tegra: add clock properties to Tegra30 DT
ARM: tegra: add clock properties to Tegra20 DT
spi: tegra: do not use clock name to get clock
ARM: tegra: remove legacy clock code
ARM: tegra: migrate to new clock code
clk: tegra: add clock support for Tegra30
clk: tegra: add clock support for Tegra20
clk: tegra: add Tegra specific clocks
ARM: tegra: define Tegra30 CAR binding
ARM: tegra: define Tegra20 CAR binding
ARM: tegra: move tegra_cpu_car.h to linux/clk/tegra.h
ARM: tegra: add function to read chipid
ARM: tegra: fix compile error when disable CPU_IDLE
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
arch/arm/mach-tegra/board-dt-tegra20.c
arch/arm/mach-tegra/board-dt-tegra30.c
arch/arm/mach-tegra/common.c
arch/arm/mach-tegra/platsmp.c
drivers/clocksource/Makefile
|
|
The device tree binding models Tegra30 CAR (Clock And Reset)
as a single monolithic clock provider.
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
[swarren: fixed typo in binding doc]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
The Tegra20 CAR (Clock And Reset) Controller controls most aspects of
most clocks within Tegra20. The device tree binding models this as a
single monolithic clock provider, which exports many clocks. This reduces
the number of nodes needed in device tree to represent these clocks.
This binding is only useful for Tegra20; the set of clocks that exists on
Tegra30 is sufficiently different to merit its own binding.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
[pgaikwad: Added mux clk ids and sorted CAR node]
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
From Sascha Hauer:
ARM i.MX SoC updates for next
Mostly clock related updates, most notably the conversion of
i.MX31 to a DT based lookup.
* tag 'imx-soc' of git://git.pengutronix.de/git/imx/linux-2.6:
ARM: clk-imx35: Fix build warnings with W=1
ARM: imx27: add a clock gate to activate SPLL clock
ARM: mx31: Replace clk_register_clkdev with clock DT lookup
ARM: clk-imx31: Add dummy clock
ARM: Let CONFIG_MACH_IMX31_DT be built by default
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Similarly as it was done for mx6q, use a DT lookup in order to make maintainance
task for the clock devices easier.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
this patche deletes hard code that registers clkdev by things like:
clk_register_clkdev(clk, NULL, "b0030000.nand");
clk_register_clkdev(clk, NULL, "b0040000.audio");
clk_register_clkdev(clk, NULL, "b0080000.usp");
prima2 clock controller becomes a clock provider and every dt node
just declares its clock sources by dt prop.
it also makes us easier to extend this driver to support both prima2
and marco as marco has different address mapping with prima2.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
'clock-output-names' is not used in any of the dts/dtsi files for i.mx.
Remove it from the examples, so that the example and the real usage in the
dtsi files can match.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Pull ARM SoC updates for Marvell mvebu/kirkwood from Olof Johansson:
"This is a branch with updates for Marvell's mvebu/kirkwood platforms.
They came in late-ish, and were heavily interdependent such that it
didn't make sense to split them up across the cross-platform topic
branches. So here they are (for the second release in a row) in a
branch on their own."
* tag 'mvebu' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (88 commits)
arm: l2x0: add aurora related properties to OF binding
arm: mvebu: add Aurora L2 Cache Controller to the DT
arm: mvebu: add L2 cache support
dma: mv_xor: fix error handling path
dma: mv_xor: fix error checking of irq_of_parse_and_map()
dma: mv_xor: use request_irq() instead of devm_request_irq()
dma: mv_xor: clear the window override control registers
arm: mvebu: fix address decoding armada_cfg_base() function
ARM: mvebu: update defconfig with I2C and RTC support
ARM: mvebu: Add SATA support for OpenBlocks AX3-4
ARM: mvebu: Add support for the RTC in OpenBlocks AX3-4
ARM: mvebu: Add support for I2C on OpenBlocks AX3-4
ARM: mvebu: Add support for I2C controllers in Armada 370/XP
arm: mvebu: Add hardware I/O Coherency support
arm: plat-orion: Add coherency attribute when setup mbus target
arm: dma mapping: Export a dma ops function arm_dma_set_mask
arm: mvebu: Add SMP support for Armada XP
arm: mm: Add support for PJ4B cpu and init routines
arm: mvebu: Add IPI support via doorbells
arm: mvebu: Add initial support for power managmement service unit
...
|
|
Pull ARM SoC device tree conversions and enablement from Olof Johansson:
"Continued device tree conversion and enablement across a number of
platforms; Kirkwood, tegra, i.MX, Exynos, zynq and a couple of other
smaller series as well.
ux500 has seen continued conversion for platforms. Several platforms
have seen pinctrl-via-devicetree conversions for simpler
multiplatform. Tegra is adding data for new devices/drivers, and
Exynos has a bunch of new bindings and devices added as well.
So, pretty much the same progression in the right direction as the
last few releases."
Fix up conflicts as per Olof.
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (185 commits)
ARM: ux500: Rename dbx500 cpufreq code to be more generic
ARM: dts: add missing ux500 device trees
ARM: ux500: Stop registering the PCM driver from platform code
ARM: ux500: Move board specific GPIO info out to subordinate DTS files
ARM: ux500: Disable the MMCI gpio-regulator by default
ARM: Kirkwood: remove kirkwood_ehci_init() from new boards
ARM: Kirkwood: Add support LED of OpenBlocks A6
ARM: Kirkwood: Convert to EHCI via DT for OpenBlocks A6
ARM: kirkwood: Add NAND partiton map for OpenBlocks A6
ARM: kirkwood: Add support second I2C bus and RTC on OpenBlocks A6
ARM: kirkwood: Add support DT of second I2C bus
ARM: kirkwood: Convert mplcec4 board to pinctrl
ARM: Kirkwood: Convert km_kirkwood to pinctrl
ARM: Kirkwood: support 98DX412x kirkwoods with pinctrl
ARM: Kirkwood: Convert IX2-200 to pinctrl.
ARM: Kirkwood: Convert lsxl boards to pinctrl.
ARM: Kirkwood: Convert ib62x0 to pinctrl.
ARM: Kirkwood: Convert GoFlex Net to pinctrl.
ARM: Kirkwood: Convert dreamplug to pinctrl.
ARM: Kirkwood: Convert dockstar to pinctrl.
...
|
|
Pull ARM SoC updates from Olof Johansson:
"This contains the bulk of new SoC development for this merge window.
Two new platforms have been added, the sunxi platforms (Allwinner A1x
SoCs) by Maxime Ripard, and a generic Broadcom platform for a new
series of ARMv7 platforms from them, where the hope is that we can
keep the platform code generic enough to have them all share one mach
directory. The new Broadcom platform is contributed by Christian
Daudt.
Highbank has grown support for Calxeda's next generation of hardware,
ECX-2000.
clps711x has seen a lot of cleanup from Alexander Shiyan, and he's
also taken on maintainership of the platform.
Beyond this there has been a bunch of work from a number of people on
converting more platforms to IRQ domains, pinctrl conversion, cleanup
and general feature enablement across most of the active platforms."
Fix up trivial conflicts as per Olof.
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (174 commits)
mfd: vexpress-sysreg: Remove LEDs code
irqchip: irq-sunxi: Add terminating entry for sunxi_irq_dt_ids
clocksource: sunxi_timer: Add terminating entry for sunxi_timer_dt_ids
irq: versatile: delete dangling variable
ARM: sunxi: add missing include for mdelay()
ARM: EXYNOS: Avoid early use of of_machine_is_compatible()
ARM: dts: add node for PL330 MDMA1 controller for exynos4
ARM: EXYNOS: Add support for secondary CPU bring-up on Exynos4412
ARM: EXYNOS: add UART3 to DEBUG_LL ports
ARM: S3C24XX: Add clkdev entry for camif-upll clock
ARM: SAMSUNG: Add s3c24xx/s3c64xx CAMIF GPIO setup helpers
ARM: sunxi: Add missing sun4i.dtsi file
pinctrl: samsung: Do not initialise statics to 0
ARM i.MX6: remove gate_mask from pllv3
ARM i.MX6: Fix ethernet PLL clocks
ARM i.MX6: rename PLLs according to datasheet
ARM i.MX6: Add pwm support
ARM i.MX51: Add pwm support
ARM i.MX53: Add pwm support
ARM: mx5: Replace clk_register_clkdev with clock DT lookup
...
|
|
In current code the ethernet PLL is not handled correctly. The PLL runs at 500MHz
and has different outputs. Only the enet reference clock is implemented. This
patch changes the PLL so that it outputs 500MHz and adds the additional outputs
as dividers. This now matches the datasheet which says:
> This PLL synthesizes a low jitter clock from 24 MHz reference clock.
> The PLL outputs a 500 MHz clock. The reference clocks generated by this PLL are:
> • Ref_PCIe = 125 MHz
> • Ref_SATA = 100 MHz
> • Ref_ethernet, which is configurable based on the PLL_ENET[1:0] register field.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
|
|
In recent reference manuals the PLLs were renumbered. PLL8 now is
PLL6 and vice versa. Change the code according to the reference
manual to avoid confusion.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Similarly as it was done for mx6q, use a DT lookup in order to make maintainance
task for the clock devices easier.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
|
|
This driver allows to provide DT clocks for clock gates found on
Marvell Dove and Kirkwood SoCs. The clock gates are referenced by
the phandle index of the corresponding bit in the clock gating control
register to ease lookup in the datasheet.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
|
|
Add Armada 370/XP specific CPU clocks
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
This driver allows to provide DT clocks for core clocks found on
Marvell Kirkwood, Dove & 370/XP SoCs. The core clock frequencies and
ratios are determined by decoding the Sample-At-Reset registers.
Although technically correct, using a divider of 0 will lead to
div_by_zero panic. Let's use a ratio of 0/1 instead to fail later
with a zero clock.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Use a better name for the USB PHY clock.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
From Michal Simek <michal.simek@xilinx.com>:
These are based on previous patches (arm-soc zynq/cleanup branch).
The branch is still based on rc3 but I have also tried to merged it
with the v3.7-rc5 and there is no issue.
* 'arm-next' of git://git.xilinx.com/linux-xlnx:
ARM: zynq: add clk binding support to the ttc
ARM: zynq: use zynq clk bindings
clk: Add support for fundamental zynq clks
ARM: zynq: dts: split up device tree
ARM: zynq: Allow UART1 to be used as DEBUG_LL console.
ARM: zynq: dts: add description of the second uart
ARM: zynq: move arm-specific sys_timer out of ttc
zynq: move static peripheral mappings
zynq: remove use of CLKDEV_LOOKUP
zynq: use pl310 device tree bindings
zynq: use GIC device tree bindings
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Provide simplified models for the necessary clocks on the zynq-7000
platform. Currently, the PLLs, the CPU clock network, and the basic
peripheral clock networks (for SDIO, SMC, SPI, QSPI, UART) are modelled.
OF bindings are also provided and documented.
Signed-off-by: Josh Cartwright <josh.cartwright@ni.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
|
|
This adds a i.MX25 dtsi file along with the i.MX25 clock tree
documentation. The devicetree should be fairly complete for:
- uart
- fec
- i2c
- spi
- pwm
- nand
- gpio
- wdog
- esdhc
- flexcan
The more exotic devices currently miss clock bindings.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
|
|
From Tony Prisk:
Update arch-vt8500 and drivers to device tree and
remove existing non-dt code.
* tag 'vt8500-for-next' of git://git.code.sf.net/p/linuxwmt/code:
arm: vt8500: Update arch-vt8500 to devicetree support.
arm: vt8500: gpio: Devicetree support for arch-vt8500
arm: vt8500: doc: Add device tree bindings for arch-vt8500 devices
arm: vt8500: clk: Add Common Clock Framework support
video: vt8500: Add devicetree support for vt8500-fb and wm8505-fb
serial: vt8500: Add devicetree support for vt8500-serial
rtc: vt8500: Add devicetree support for vt8500-rtc
arm: vt8500: Add device tree files for VIA/Wondermedia SoC's
Resolved add/change conflict in drivers/clk/Makefile.
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Bindings for gpio, interrupt controller, power management controller,
timer, realtime clock, serial uart, ehci and uhci controllers and
framebuffer controllers used on the arch-vt8500 platform.
Framebuffer binding also specifies a 'display' node which is required
for determining the lcd panel data.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
|
|
It replaces the clk_register_clkdev in imx6q clock driver with DT
lookup. It depends on Mike's clk-3.7 branch.
* tag 'imx-clk-dt-lookup' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx6q: replace clk_register_clkdev with clock DT lookup
Resolved context add/remove conflict in arch/arm/boot/dts/imx6q.dtsi
|
|
It really becomes an maintenance issue that every time a device needs
to look up (clk_get) a clock we have to patch kernel clock file to call
clk_register_clkdev for that clock.
Since clock DT support which is meant to resolve clock lookup in device
tree is in place, the patch moves imx6q client devices' clock lookup
over to device tree, so that any new lookup to be added at later time
can just get done in DT instead of kernel.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
It really becomes a maintenance issue that every time a device needs
to look up (clk_get) a clock we have to patch kernel clock file to call
clk_register_clkdev for that clock.
Since clock DT support which is meant to resolve clock lookup in device
tree is in place, the patch moves imx23 client devices' clock lookup
over to device tree, so that any new lookup to be added at later time
can just get done in DT instead of kernel.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
It really becomes a maintenance issue that every time a device needs
to look up (clk_get) a clock we have to patch kernel clock file to call
clk_register_clkdev for that clock.
Since clock DT support which is meant to resolve clock lookup in device
tree is in place, the patch moves imx28 client devices' clock lookup
over to device tree, so that any new lookup to be added at later time
can just get done in DT instead of kernel.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
This adds real clock support to Calxeda Highbank SOC using the common
clock infrastructure.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
[mturquette@linaro.org: fixed up invalid writes to const struct member]
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Based on work 1st by Ben Herrenschmidt and Jeremy Kerr, then by Grant
Likely, this patch adds support to clk_get to allow drivers to retrieve
clock data from the device tree.
Platforms scan for clocks in DT with of_clk_init and a match table, and
the register a provider through of_clk_add_provider. The provider's
clk_src_get function will be called when a device references the
provider's OF node for a clock reference.
v6 (Rob Herring):
- Return error values instead of NULL to match clock framework
expectations
v5 (Rob Herring):
- Move from drivers/of into common clock subsystem
- Squashed "dt/clock: add a simple provider get function" and
"dt/clock: add function to get parent clock name"
- Rebase to 3.4-rc1
- Drop CONFIG_OF_CLOCK and just use CONFIG_OF
- Add missing EXPORT_SYMBOL to various functions
- s/clock-output-name/clock-output-names/
- Define that fixed-clock binding is a single output
v4 (Rob Herring):
- Rework for common clk subsystem
- Add of_clk_get_parent_name function
v3: - Clarified documentation
v2: - fixed errant ';' causing compile error
- Editorial fixes from Shawn Guo
- merged in adding lookup to clkdev
- changed property names to match established convention. After
working with the binding a bit it really made more sense to follow the
lead of 'reg', 'gpios' and 'interrupts' by making the input simply
'clocks' & 'clock-names' instead of 'clock-input-*', and to only use
clock-output* for the producer nodes. (Sorry Shawn, this will mean
you need to change some code, but it should be trivial)
- Add ability to inherit clocks from parent nodes by using an empty
'clock-ranges' property. Useful for busses. I could use some feedback
on the new property name, 'clock-ranges' doesn't feel right to me.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Shawn Guo <shawn.guo@freescale.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
Linus Torvalds
Arnd Bergmann
Jason Cooper
Martin Fuzzey
Peter Chen
Olof Johansson
Prashant Gaikwad
Stephen Warren
Fabio Estevam
Barry Song
Sascha Hauer
Gregory CLEMENT
Sebastian Hesselbarth
Josh Cartwright
Tony Prisk
Shawn Guo
Rob Herring
Grant Likely