| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
|
|
|
|
In general Renesas hardware is not documented to the extent where the
relationship between IP blocks on different SoCs can be assumed although
they may appear to operate the same way. Furthermore the documentation
typically does not specify a version for individual IP blocks. For these
reasons a convention of using the SoC name in place of a version and
providing SoC-specific compatibility strings has been adopted.
Although not universally liked this convention is used in the bindings for
most drivers for Renesas hardware. The purpose of this patch is to
update the Renesas USB DMA Controller driver to follow this convention.
Cc: devicetree@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This change makes the DT file to be easier to read since the reserved slots
array does not need the '/bits/ 16' to be specified, which might confuse
some people.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This change makes the DT file to be easier to read since the memcpy
channels array does not need the '/bits/ 16' to be specified, which might
confuse some people.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
In eDMA the events are directly mapped to a DMA channel (for example DMA
event 14 can only be handled by DMA channel 14). If the memcpy is enabled
on the eDMA, there is a possibility that the crossbar driver would assign
DMA event number already allocated in eDMA for memcpy. Furthermore the
eDMA can be shared with DSP in which case the crossbar driver should also
avoid mapping xbar events to DSP used event numbers (or channels).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This patch adds documentation of device tree bindings for the STM32 dma
controller.
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
With the old binding and driver architecture we had many issues:
No way to assign eDMA channels to event queues, thus not able to tune the
system by moving specific DMA channels to low/high priority servicing. We
moved the cyclic channels to high priority within the code, but that was
just a workaround to this issue.
Memcopy was fundamentally broken: even if the driver scanned the DT/devices
in the booted system for direct DMA users (which is not effective when the
events are going through a crossbar) and created a map of 'used' channels,
this information was not really usable. Since via dmaengien API the eDMA
driver will be called with _some_ channel number, we would try to request
this channel when any channel is requested for memcpy. By luck we got
channel which is not used by any device most of the time so things worked,
but if a device would have been using the given channel, but not requested
it, the memcpy channel would have been waiting for HW event.
The old code had the am33xx/am43xx DMA event router handling embedded. This
should have been done in a separate driver since it is not part of the
actual eDMA IP.
There were no way to 'lock' PaRAM slots to be used by the DSP for example
when booting with DT.
In DT boot the edma node used more than one hwmod which is not a good
practice and the kernel prints warning because of this.
With the new bindings and the changes in the driver we can:
- No regression with Legacy binding and non DT boot
- DMA channels can be assigned to any TC (to set priority)
- PaRAM slots can be reserved for other cores to use
- Dynamic power management for CC and TCs, if only TC0 is used all other TC
can be powered down for example
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The DMA event crossbar on AM33xx/AM43xx is different from the one found in
DRA7x family.
Instead of a single event crossbar it has 64 identical mux attached to each
eDMA event line. When the 0 event mux is selected, the default mapped event
is going to be routed to the corresponding eDMA event line. If different
mux is selected, then the selected event is going to be routed to the given
eDMA event.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Pull dmaengine updates from Vinod Koul:
"This time we have aded a new capability for scatter-gathered memset
using dmaengine APIs. This is supported in xdmac & hdmac drivers
We have added support for reusing descriptors for examples like video
buffers etc. Driver will follow
The behaviour of descriptor ack has been clarified and documented
New devices added are:
- dma controller in sun[457]i SoCs
- lpc18xx dmamux
- ZTE ZX296702 dma controller
- Analog Devices AXI-DMAC DMA controller
- eDMA support for dma-crossbar
- imx6sx support in imx-sdma driver
- imx-sdma device to device support
Other:
- jz4780 fixes
- ioatdma large refactor and cleanup for removal of ioat v1 and v2
which is deprecated and fixes
- ACPI support in X-Gene DMA engine driver
- ipu irq fixes
- mvxor fixes
- minor fixes spread thru drivers"
[ The Kconfig and Makefile entries got re-sorted alphabetically, and I
handled the conflict with the new Intel integrated IDMA driver by
slightly mis-sorting it on purpose: "IDMA64" got sorted after "IMX" in
order to keep the Intel entries together. I think it might be a good
idea to just rename the IDMA64 config entry to INTEL_IDMA64 to make
the sorting be a true sort, not this mismash.
Also, this merge disables the COMPILE_TEST for the sun4i DMA
controller, because it does not compile cleanly at all. - Linus ]
* tag 'dmaengine-4.3-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (89 commits)
dmaengine: ioatdma: add Broadwell EP ioatdma PCI dev IDs
dmaengine :ipu: change ipu_irq_handler() to remove compile warning
dmaengine: ioatdma: Fix variable array length
dmaengine: ioatdma: fix sparse "error" with prep lock
dmaengine: hdmac: Add memset capabilities
dmaengine: sort the sh Makefile
dmaengine: sort the sh Kconfig
dmaengine: sort the dw Kconfig
dmaengine: sort the Kconfig
dmaengine: sort the makefile
drivers/dma: make mv_xor.c driver explicitly non-modular
dmaengine: Add support for the Analog Devices AXI-DMAC DMA controller
devicetree: Add bindings documentation for Analog Devices AXI-DMAC
dmaengine: xgene-dma: Fix the lock to allow client for further submission of requests
dmaengine: ioatdma: fix coccinelle warning
dmaengine: ioatdma: fix zero day warning on incompatible pointer type
dmaengine: tegra-apb: Simplify locking for device using global pause
dmaengine: tegra-apb: Remove unnecessary return statements and variables
dmaengine: tegra-apb: Avoid unnecessary channel base address calculation
dmaengine: tegra-apb: Remove unused variables
...
|
|
Add the devicetree descriptor for the Analog Devices AXI-DMAC DMA
controller. This is a soft peripheral used in FPGAs and the bindings
describe how it is connected to the system (clock, interrupt, memory map)
as well as the configuration options that were used when the peripheral was
instantiated.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
|
|
This patch adds support for the DMA engine present on Allwinner A10,
A13, A10S and A20 SoCs. This engine has two kinds of channels: normal
and dedicated. The main difference is in the mode of operation;
while a single normal channel may be operating at any given time,
dedicated channels may operate simultaneously provided there is no
overlap of source or destination.
Hardware documentation can be found on A10 User Manual (section 12), A13
User Manual (section 14) and A20 User Manual (section 1.12)
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The only reason why we had dmacap,* properties is because back when
DMA_MEMSET was supported, only one out of the two channels per engine
could do a memset operation. But this is something that the driver
already knows anyway, and since then, the DMA_MEMSET support has been
removed.
The driver is already well aware of what each channel supports and the
one to one mapping between Linux specific implementation details (such
as dmacap,interrupt enabling DMA_INTERRUPT) and DT properties is a
good indication that these DT properties are wrong.
Therefore, this commit simply gets rid of these dmacap,* properties,
they are now ignored, and the driver is responsible for knowing the
capabilities of the hardware with regard to the dmaengine subsystem
expectations.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Add device tree bindings documentation for the
lpc1850-dmamux DMA router.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This introduces device tree bindings for the PL08x DMA controllers
when used with fixed signal assignment per channel, i.e. if each
channel on the PL08x is assigned precisely one burst/single signal
set.
[je: remove channel sub-node parsing, use cell value to assign AHB]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
There is an overlap in dma ring cmd csr region due to sharing of ethernet
ring cmd csr region. This patch fix the resource overlapping by mapping
the entire dma ring cmd csr region.
Signed-off-by: Rameshwar Prasad Sahu <rsahu@apm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This patch adds documentation for the ZTE ZX296702 SoC DMA device
DTS binding.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Pull dmaengine updates from Vinod Koul:
"This time we have support for few new devices, few new features and
odd fixes spread thru the subsystem.
New devices added:
- support for CSRatlas7 dma controller
- Allwinner H3(sun8i) controller
- TI DMA crossbar driver on DRA7x
- new pxa driver
New features added:
- memset support is bought back now that we have a user in xdmac controller
- interleaved transfers support different source and destination strides
- supporting DMA routers and configuration thru DT
- support for reusing descriptors
- xdmac memset and interleaved transfer support
- hdmac support for interleaved transfers
- omap-dma support for memcpy
Others:
- Constify platform_device_id
- mv_xor fixes and improvements"
* tag 'dmaengine-4.2-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (46 commits)
dmaengine: xgene: fix file permission
dmaengine: fsl-edma: clear pending interrupts on initialization
dmaengine: xdmac: Add memset support
Documentation: dmaengine: document DMA_CTRL_ACK
dmaengine: virt-dma: don't always free descriptor upon completion
dmaengine: Revert "drivers/dma: remove unused support for MEMSET operations"
dmaengine: hdmac: Implement interleaved transfers
dmaengine: Move icg helpers to global header
dmaengine: mv_xor: improve descriptors list handling and reduce locking
dmaengine: mv_xor: Enlarge descriptor pool size
dmaengine: mv_xor: add support for a38x command in descriptor mode
dmaengine: mv_xor: Rename function for consistent naming
dmaengine: mv_xor: bug fix for racing condition in descriptors cleanup
dmaengine: pl330: fix wording in mcbufsz message
dmaengine: sirf: add CSRatlas7 SoC support
dmaengine: xgene-dma: Fix "incorrect type in assignement" warnings
dmaengine: fix kernel-doc documentation
dmaengine: pxa_dma: add support for legacy transition
dmaengine: pxa_dma: add debug information
dmaengine: pxa: add pxa dmaengine driver
...
|
|
|
|
The Marvell Armada 38x SoC introduce new features to the XOR engine,
especially the fact that the engine mode (MEMCPY/XOR/PQ/etc) can be part of
the descriptor and not set through the controller registers.
This new feature allows mixing of different commands (even PQ) on the same
channel/chain without the need to stop the engine to reconfigure the engine
mode.
Refactor the driver to be able to use that new feature on the Armada 38x,
while keeping the old behaviour on the older SoCs.
Signed-off-by: Lior Amsalem <alior@marvell.com>
Reviewed-by: Ofer Heifetz <oferh@marvell.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
add support for new CSR atlas7 SoC. atlas7 exists V1 and V2 IP.
atlas7 DMAv1 is basically moved from marco, which has never been
delivered to customers and renamed in this patch.
atlas7 DMAv2 supports chain DMA by a chain table, this
patch also adds chain DMA support for atlas7.
atlas7 DMAv1 and DMAv2 co-exist in the same chip. there are some HW
configuration differences(register offset etc.) with old prima2 chips,
so we use compatible string to differentiate old prima2 and new atlas7,
then results in different set in HW for them.
Signed-off-by: Hao Liu <Hao.Liu@csr.com>
Signed-off-by: Yanchang Li <Yanchang.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The DRA7x has more peripherals with DMA requests than the sDMA can handle:
205 vs 127. All DMA requests are routed through the DMA crossbar, which can
be configured to route selected incoming DMA requests to specific request
line of the DMA controller.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
DMA routers are transparent devices used to mux DMA requests from
peripherals to DMA controllers. They are used when the SoC integrates more
devices with DMA requests then their controller can handle.
DRA7x is one example of such SoC, where the sDMA can hanlde 128 DMA request
lines, but in SoC level it has 205 DMA requests.
The of_dma_router will be registered as of_dma_controller with special
xlate function and additional parameters. The driver for the router is
responsible to craft the dma_spec (in the of_dma_route_allocate callback)
which can be used to requests a DMA channel from the real DMA controller.
This way the router can be transparent for the system while remaining generic
enough to be used in different environments.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The H3 SoC has the same dma engine as the A31 (sun6i), with a
reduced amount of endpoints and physical channels. Add the proper
config data and compatible string to support it.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Fix a typo in the TX DMA interrupt name for AUART4.
This patch makes AUART4 operational again.
Signed-off-by: Marek Vasut <marex@denx.de>
Fixes: f30fb03d4d3a ("ARM: dts: add generic DMA device tree binding for mxs-dma")
Cc: stable@vger.kernel.org
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Pull slave-dmaengine updates from Vinod Koul:
- new drivers for:
- Ingenic JZ4780 controller
- APM X-Gene controller
- Freescale RaidEngine device
- Renesas USB Controller
- remove device_alloc_chan_resources dummy handlers
- sh driver cleanups for peri peri and related emmc and asoc patches
as well
- fixes and enhancements spread over the drivers
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (59 commits)
dmaengine: dw: don't prompt for DW_DMAC_CORE
dmaengine: shdmac: avoid unused variable warnings
dmaengine: fix platform_no_drv_owner.cocci warnings
dmaengine: pch_dma: fix memory leak on failure path in pch_dma_probe()
dmaengine: at_xdmac: unlock spin lock before return
dmaengine: xgene: devm_ioremap() returns NULL on error
dmaengine: xgene: buffer overflow in xgene_dma_init_channels()
dmaengine: usb-dmac: Fix dereferencing freed memory 'desc'
dmaengine: sa11x0: report slave capabilities to upper layers
dmaengine: vdma: Fix compilation warnings
dmaengine: fsl_raid: statify fsl_re_chan_probe
dmaengine: Driver support for FSL RaidEngine device.
dmaengine: xgene_dma_init_ring_mngr() can be static
Documentation: dma: Add documentation for the APM X-Gene SoC DMA device DTS binding
arm64: dts: Add APM X-Gene SoC DMA device and DMA clock DTS nodes
dmaengine: Add support for APM X-Gene SoC DMA engine driver
dmaengine: usb-dmac: Add Renesas USB DMA Controller (USB-DMAC) driver
dmaengine: renesas,usb-dmac: Add device tree bindings documentation
dmaengine: edma: fixed wrongly initialized data parameter to the edma callback
dmaengine: ste_dma40: fix implicit conversion
...
|
|
|
|
This patch adds documentation for the APM X-Gene SoC DMA device DTS binding
Signed-off-by: Rameshwar Prasad Sahu <rsahu@apm.com>
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Document the device tree bindings for the Renesas USB DMA
Controller (USB-DMAC).
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Add device tree bindings for the DMA controller on JZ4780 SoCs, used by
the dma-jz4780 driver.
Signed-off-by: Alex Smith <alex.smith@imgtec.com>
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This patchset attempts to standardize the naming of dt-bindings
documents based on the Broadcom vendor prefix of brcm.
Although there are no guidelines currently present for how to name
the dt-bindings document the "vendor,binding.txt" style is in use by
some of the other vendors.
Acked-by: Lee Jones <lee@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Renesas R-Car sound (= rsnd) needs 2 DMAC which are called as
Audio DMAC (= 1st DMAC) and Audio DMAC peri peri (2nd DMAC).
And rsnd had assumed that 1st / 2nd DMACs are implemented as DMAEngine.
But, in result of DMA ML discussion, 2nd DMAC was concluded that it is
not a general purpose DMAC (2nd DMAC is for Device to Device inside
sound system). Additionally, current DMAEngine can't support Device to
Device, and we don't have correct DT bindings for it at this point.
So the easiest solution for it is that move it from DMAEngine to rsnd
driver.
Audio DMAC peri peri on DMAEngine is no longer needed. remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add register offset table entry for the newer (v1.7.0) version of the BAM IP
found on MSM8916. Update the DT bindings documentation.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Pull dmaengine updates from Vinod Koul:
"This update brings:
- the big cleanup up by Maxime for device control and slave
capabilities. This makes the API much cleaner.
- new IMG MDC driver by Andrew
- new Renesas R-Car Gen2 DMA Controller driver by Laurent along with
bunch of fixes on rcar drivers
- odd fixes and updates spread over driver"
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (130 commits)
dmaengine: pl330: add DMA_PAUSE feature
dmaengine: pl330: improve pl330_tx_status() function
dmaengine: rcar-dmac: Disable channel 0 when using IOMMU
dmaengine: rcar-dmac: Work around descriptor mode IOMMU errata
dmaengine: rcar-dmac: Allocate hardware descriptors with DMAC device
dmaengine: rcar-dmac: Fix oops due to unintialized list in error ISR
dmaengine: rcar-dmac: Fix spinlock issues in interrupt
dmaenegine: edma: fix sparse warnings
dmaengine: rcar-dmac: Fix uninitialized variable usage
dmaengine: shdmac: extend PM methods
dmaengine: shdmac: use SET_RUNTIME_PM_OPS()
dmaengine: pl330: fix bug that cause start the same descs in cyclic
dmaengine: at_xdmac: allow muliple dwidths when doing slave transfers
dmaengine: at_xdmac: simplify channel configuration stuff
dmaengine: at_xdmac: introduce save_cc field
dmaengine: at_xdmac: wait for in-progress transaction to complete after pausing a channel
ioat: fail self-test if wait_for_completion times out
dmaengine: dw: define DW_DMA_MAX_NR_MASTERS
dmaengine: dw: amend description of dma_dev field
dmatest: move src_off, dst_off, len inside loop
...
|
|
Instead of using magic number in the code the patch provides
DW_DMA_MAX_NR_MASTERS constant.
While here, restrict the reading of data width array by amount of the actual
number of AHB masters.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Add a binding document for the IMG Multi-threaded DMA Controller (MDC)
present on the MIPS-based Pistachio and other IMG SoCs.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This patch fix multiple words such as "the the" and "which which"
in Documentation/devicetree.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
DT bindings are complex enough without expressing the same information
twice in a slightly different way. Remove the duplicate.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
The specification requires xlnx,data-width, but example and driver use
xlnx,datawidth. Change the specification to match the implementation.
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Fixes: eebeac03db93 ("dma: Add Xilinx Video DMA DT Binding Documentation")
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
|
|
The dma-cells value in the example was 2 instead of 1.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This patch simply adds a new DMATYPE for SAI which's included
in i.MX6 Solo X.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Add compatible string for BAM v1.3.0 in the DT bindings documentation. Mentioned
a few more SoCs which have BAM v1.4.0 in them.
Reviewed-by: Kumar Gala <galak@codeaurora.org>
Reviewed-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The A23 SoC has the same dma engine as the A31 (sun6i), with a
reduced amount of endpoints and physical channels. Add the proper
config data and compatible string to support it.
A slight difference in sun8i is an undocumented register needs
to be toggled for dma to function.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Add bindings documentation for the new Atmel DMA controller (XDMAC)
introduced with SAMA5D4.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Pull slave-dmaengine updates from Vinod Koul:
"For dmaengine contributions we have:
- designware cleanup by Andy
- my series moving device_control users to dmanegine_xxx APIs for
later removal of device_control API
- minor fixes spread over drivers mainly mv_xor, pl330, mmp, imx-sdma
etc"
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (60 commits)
serial: atmel: add missing dmaengine header
dmaengine: remove FSLDMA_EXTERNAL_START
dmaengine: freescale: remove FSLDMA_EXTERNAL_START control method
carma-fpga: move to fsl_dma_external_start()
carma-fpga: use dmaengine_xxx() API
dmaengine: freescale: add and export fsl_dma_external_start()
dmaengine: add dmaengine_prep_dma_sg() helper
video: mx3fb: use dmaengine_terminate_all() API
serial: sh-sci: use dmaengine_terminate_all() API
net: ks8842: use dmaengine_terminate_all() API
mtd: sh_flctl: use dmaengine_terminate_all() API
mtd: fsmc_nand: use dmaengine_terminate_all() API
V4L2: mx3_camer: use dmaengine_pause() API
dmaengine: coh901318: use dmaengine_terminate_all() API
pata_arasan_cf: use dmaengine_terminate_all() API
dmaengine: edma: check for echan->edesc => NULL in edma_dma_pause()
dmaengine: dw: export probe()/remove() and Co to users
dmaengine: dw: enable and disable controller when needed
dmaengine: dw: always export dw_dma_{en,dis}able
dmaengine: dw: introduce dw_dma_on() helper
...
|
|
Add device tree binding support for the QCOM ADM DMA driver.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Current dmas explanation of SRC/DRS is confusable.
This patch clarifies it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Device-tree binding documentation of Xilinx DMA Engine
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
Vinod Koul
Simon Horman
Peter Ujfalusi
M'boumba Cedric Madianga
Linus Torvalds
Lars-Peter Clausen
Emilio López
Thomas Petazzoni
Joachim Eastwood
Linus Walleij
Rameshwar Prasad Sahu
Jun Nie
Lior Amsalem
Hao Liu
Jens Kuske
Marek Vasut
Yoshihiro Shimoda
Alex Smith
Scott Branden
Kuninori Morimoto
Archit Taneja
Andy Shevchenko
Andrew Bresticker
Masanari Iida
Laurent Pinchart
Andreas Färber
Ludovic Desroches
Nicolin Chen
Chen-Yu Tsai
Andy Gross
Srikanth Thokala