| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The device can optionally supply an interrupt, hence document that.
Add required GPIO properties to the example (extracted from a patch by
Wolfram Sang).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
It is not completely obvious that these are required and
how to use them. So we provide a tested example.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Hardware can have a switchable Vcc supply, so let's add it to
the bindings (the current Linux driver code already supports it).
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Pyra-Handheld originally used the tca6424 but recently we have
replaced it by the pin and package compatible pcal6524. So let's
add this to the bindings and the driver.
And while we are at it, the pcal9555a does not have a compatible entry
either but is already supported by the device id table.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Despite commit 55020c8056a8 ("of: Add vendor prefix for ON Semiconductor
Corp.") was made long ago, the latter commit 9f49f6dd0473 ("gpio: pca953x:
add onsemi,pca9654 id") made use of another, undocumented vendor prefix.
Since such prefix doesn't seem to be used in any device trees, I think we
can just fix the "compatible" string in the driver and the bindings and be
done with that...
Fixes: 9f49f6dd0473 ("gpio: pca953x: add onsemi,pca9654 id")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The TCA9554 is similar to the PCA9554. Update the DT binding docs.
Signed-off-by: Anders Darander <anders@chargestorm.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add optional reset-gpios pin control. If present, de-assert the
specified reset gpio pin to bring the chip out of reset.
v2:
- Specify that reset signal to PCA953x chip is active low, in
binding doc.
- reorder includes in gpio-pca953x.c.
- remove dev_err() on devm_gpiod_get_optional() error return.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
TI PCA9536 is 4-Bit I2C GPIO expander without interrupt support[1].
Add support for the same.
[1] TRM: http://www.ti.com/lit/ds/symlink/pca9536.pdf
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add onsemi,pca9654 which is also compatible with the nxp,pca9524 as it
is an 8bit expander with an interrupt output.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The TCA9539 is almost identical to the PCA9555 and software-compatible
with this driver. It exposes 16 general purpose I/O pins in two 8-bit
configurations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add a devicetree binding documentation for the pca953x driver.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
Geert Uytterhoeven
H. Nikolaus Schaller
Sergei Shtylyov
Anders Darander
Steve Longerbeam
Vignesh R
Ben Dooks
Thierry Reding
Markus Pargmann