| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
In the past, there have been words on various lists that if LDO3 is
disabled in u-boot, but enabled in the DTS, the axp209 driver would
fail to continue/hang. Several enable/disable patches have been
issues to devicetree's in both the kernel and u-boot to address
this issue.
What really happened however, was that the AXP209 shuts down without
a notice and without setting an interrupt. This is caused when LDO3
gets overloaded, for example with large capacitors on the LDO3 output.
Normally, we would expect that AXP209 would source 200 mA as per
datasheet and set and trigger an interrupt when being overloaded.
For some reason however, this does not happen.
As a work-around, implement software-based 'regulator-soft-start'
property for AXP209 LDO3 regulator, which is used to first bring up
the LDO3 to the lowest possible voltage and then enable the LDO.
After that, we can set the requested voltage as usual.
Combining this setting with the regulator-ramp-delay allows LDO3 to
come up slowly and staggered, potentially reducing overall inrush current.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The AXP209 supports ramping up voltages on several regulators such as
DCDC2 and LDO3, therefore we can use the standard 'regulator-ramp-delay'
property for those 2 regulators.
Note that the voltage ramp only works when the regulator is already
enabled. E.g. when going from say 0.7 V to 3.6 V.
When turning on the regulator, no voltage ramp is performed in hardware.
What this means, is that if the bootloader brings up the voltage at 0.7 V,
the ramp delay property is properly applied. If however, the bootloader
leaves the power off, no ramp delay is applied when the power is
enabled by the regulator framework.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Pull Devicetree updates from Rob Herring:
"A bit bigger than normal as I've been busy this cycle.
There's a few things with dependencies and a few things subsystem
maintainers didn't pick up, so I'm taking them thru my tree.
The fixes from Johan didn't get into linux-next, but they've been
waiting for some time now and they are what's left of what subsystem
maintainers didn't pick up.
Summary:
- Sync dtc with upstream version v1.4.7-14-gc86da84d30e4
- Work to get rid of direct accesses to struct device_node name and
type pointers in preparation for removing them. New helpers for
parsing DT cpu nodes and conversions to use the helpers. printk
conversions to %pOFn for printing DT node names. Most went thru
subystem trees, so this is the remainder.
- Fixes to DT child node lookups to actually be restricted to child
nodes instead of treewide.
- Refactoring of dtb targets out of arch code. This makes the support
more uniform and enables building all dtbs on c6x, microblaze, and
powerpc.
- Various DT binding updates for Renesas r8a7744 SoC
- Vendor prefixes for Facebook, OLPC
- Restructuring of some ARM binding docs moving some peripheral
bindings out of board/SoC binding files
- New "secure-chosen" binding for secure world settings on ARM
- Dual licensing of 2 DT IRQ binding headers"
* tag 'devicetree-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (78 commits)
ARM: dt: relicense two DT binding IRQ headers
power: supply: twl4030-charger: fix OF sibling-node lookup
NFC: nfcmrvl_uart: fix OF child-node lookup
net: stmmac: dwmac-sun8i: fix OF child-node lookup
net: bcmgenet: fix OF child-node lookup
drm/msm: fix OF child-node lookup
drm/mediatek: fix OF sibling-node lookup
of: Add missing exports of node name compare functions
dt-bindings: Add OLPC vendor prefix
dt-bindings: misc: bk4: Add device tree binding for Liebherr's BK4 SPI bus
dt-bindings: thermal: samsung: Add SPDX license identifier
dt-bindings: clock: samsung: Add SPDX license identifiers
dt-bindings: timer: ostm: Add R7S9210 support
dt-bindings: phy: rcar-gen2: Add r8a7744 support
dt-bindings: can: rcar_can: Add r8a7744 support
dt-bindings: timer: renesas, cmt: Document r8a7744 CMT support
dt-bindings: watchdog: renesas-wdt: Document r8a7744 support
dt-bindings: thermal: rcar: Add device tree support for r8a7744
Documentation: dt: Add binding for /secure-chosen/stdout-path
dt-bindings: arm: zte: Move sysctrl bindings to their own doc
...
|
|
Pull MFD updates from Lee Jones:
"New Drivers
- Add support for USART SPI to AT91*
New Functionality
- Add support for Audio CODECs to motorola-cpcap
Fix-ups
- DT documentation fix-ups; atmel-usart
- Staticise functions/structs; spi-at91-usart, arizona-core
- Constify; ti-lmu
- Fix memory leaks; menelaus
- Change device 'wake-up' status; ti_am335x_tscadc, max8997
- Power Management (suspend/resume) semantic changes; ti_am335x_adc, cros_ec, max8997
- SPDX churn; sec-core (+ headers), max* (+ headers), intel* (+ headers),
- Trivial (whitespace, email addresses, alphabetisise); Kconfig, adp5520, intel_soc_pmic_*
- Build as module; sec-irq
- Use new %pOFn printk format for device_node.name; max77620
- Remove unused code; madera
- Use generic MACROs; intel_msic, intel_soc_pmic_crc
- Move to GPIOD; ti-lmu
- Use managed resources; ti-lmu
Bug Fixes
- Add missing headers; at91-usart
- Prevent device from entering low-power mode; arizona-core
- Poll for BOOT_DONE to avoid still-booting NACK; madera-core
- Prevent ADC read from shutting down device; mc13xxx-core"
* tag 'mfd-next-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (45 commits)
mfd: cros_ec: Avoid unneeded internal declaration warning
mfd: ti-lmu: Use of_device_get_match_data() helper
mfd: ti-lmu: Use managed resource for everything
mfd: ti-lmu: Switch to GPIOD
mfd: ti-lmu: constify mfd_cell tables
mfd: max8997: Disable interrupt handling for suspend/resume cycle
mfd: max8997: Enale irq-wakeup unconditionally
mfd: arizona: Make array mclk_name static, shrinks object size
MAINTAINERS: Add myself as designated reviewer of Intel MFD PMIC
mfd: Convert Intel PMIC drivers to use SPDX identifier 1;5201;0c Reduce size of duplicated comments by switching to use SPDX identifier.
mfd: Sort headers alphabetically for Intel PMIC drivers
mfd: intel_soc_pmic_bxtwc: Chain power button IRQs as well
mfd: intel_soc_pmic_crc: Use REGMAP_IRQ_REG() macro
mfd: intel_soc_pmic_crc: Use DEFINE_RES_IRQ_NAMED() macro
mfd: intel_msic: Use DEFINE_RES_IRQ() macro
mfd: motorola-cpcap: Add audio-codec support
mfd: mc13xxx-core: Fix PMIC shutdown when reading ADC values
mfd: madera: Remove unused forward reference
mfd: max77620: Convert to using %pOFn instead of device_node.name
mfd: madera: Don't use regmap_read_poll_timeout to poll for BOOT_DONE
...
|
|
Add ROHM BD71847 Power Management IC MFD binding information to
device-tree binding documents.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
IRQ number was missing.
Suggested-by: Radu Nicolae Pirea <pirea.radu@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch moves the bindings for serial from serial/atmel-usart.txt to
mfd/atmel-usart.txt and adds bindings for USART in SPI mode.
Signed-off-by: Radu Pirea <radu.pirea@microchip.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Pull MFD updates from Lee Jones:
"New Drivers:
- Add Cirrus Logic Madera Codec (CS47L35, CS47L85 and CS47L90/91) driver
- Add ChromeOS EC CEC driver
- Add ROHM BD71837 PMIC driver
New Device Support:
- Add support for Dialog Semi DA9063L PMIC variant to DA9063
- Add support for Intel Ice Lake to Intel-PLSS-PCI
- Add support for X-Powers AXP806 to AXP20x
New Functionality:
- Add support for USB Charging to the ChromeOS Embedded Controller
- Add support for HDMI CEC to the ChromeOS Embedded Controller
- Add support for HDMI CEC to Intel HDMI
- Add support for accessory detection to Madera devices
- Allow individual pins to be configured via DT' wlf,csnaddr-pd
- Provide legacy platform specific EEPROM/Watchdog commands; rave-sp
Fix-upsL
- Trivial renaming/spelling fixes; cros_ec, da9063-*
- Convert to Managed Resources (devm_*); da9063-*, ti_am335x_tscadc
- Transition to helper macros/functions; da9063-*
- Constify; kempld-core
- Improve error path/messages; wm8994-core
- Disable IRQs locally instead of relying on USB subsystem; dln2
- Remove unused code; rave-sp
- New exports; sec-core
Bug Fixes:
- Fix possible false I2C transaction error; arizona-core
- Fix declared memory area size; hi655x-pmic
- Fix checksum type; rave-sp
- Fix incorrect default serial port configuration: rave-sp
- Fix incorrect coherent DMA mask for sub-devices; sm501"
* tag 'mfd-next-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (60 commits)
mfd: madera: Add register definitions for accessory detect
mfd: sm501: Set coherent_dma_mask when creating subdevices
mfd: bd71837: Devicetree bindings for ROHM BD71837 PMIC
mfd: bd71837: Core driver for ROHM BD71837 PMIC
media: platform: cros-ec-cec: Fix dependency on MFD_CROS_EC
mfd: sec-core: Export OF module alias table
mfd: as3722: Disable auto-power-on when AC OK
mfd: axp20x: Support AXP806 in I2C mode
mfd: axp20x: Add self-working mode support for AXP806
dt-bindings: mfd: axp20x: Add "self-working" mode for AXP806
mfd: wm8994: Allow to configure CS/ADDR Pulldown from dts
mfd: wm8994: Allow to configure Speaker Mode Pullup from dts
mfd: rave-sp: Emulate CMD_GET_STATUS on device that don't support it
mfd: rave-sp: Add legacy watchdog ping command translation
mfd: rave-sp: Add legacy EEPROM access command translation
mfd: rave-sp: Initialize flow control and parity of the port
mfd: rave-sp: Fix incorrectly specified checksum type
mfd: rave-sp: Remove unused defines
mfd: hi655x: Fix regmap area declared size for hi655x
mfd: ti_am335x_tscadc: Fix struct clk memory leak
...
|
|
Document devicetree bindings for ROHM BD71837 PMIC MFD.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
On ams AS3722, power on when AC OK is enabled by default.
Making this option as disable by default and enable only
when platform need this explicitly.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Bibek Basu <bbasu@nvidia.com>
Tested-by: Bibek Basu <bbasu@nvidia.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The AXP806 has three operation modes:
- master mode: The PMIC is the first or only AXP PMIC in the system,
but is not in charge of power management, i.e. only
provides regulator functions.
- slave mode: The PMIC is the second AXP PMIC in the system, chained
to the first, or master, one.
- self-working mode: The PMIC is the only AXP PMIC in the system, and
is in charge of power sequencing.
The functional differences between these modes can be found in the
"Control and Operation" chapter of the AXP806 (in Chinese) and AXP805
(in English) datasheets. These include how the PMIC responds to external
signals, whether it takes an external voltage reference or uses its own,
and whether the EN/PWRON pin functions as an enable switch or power button.
We already support both slave and master mode. This patch adds a property
for describing the self-working mode, and reworks the description for
the mode properties.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Icenowy Zheng <icenowy@aosc.io>
Tested-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch fixes documentation of tps65911 because its list of
compatible regulators contains wrongly vdd3 instead of vdd2.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Immutable branch (mfd, chrome) due for the v4.19 window
Immutable Branch which moves the cros_ec_i2c and cros_ec_spi
transport drivers from mfd to platform/chrome. Changes in arm are a simple
rename in defconfigs. Change in input is a rename in help text.
|
|
'interrupt-parent' is often documented as part of define bindings, but
it is really outside the scope of a device binding. It's never required
in a given node as it is often inherited from a parent node. Or it can
be implicit if a parent node is an 'interrupt-controller' node. So
remove it from all the binding files.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
As files got renamed, their references broke.
Manually fix a series of broken refs at the DT bindings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
|
|
Rename:
pinctrl-binding.txt -> pinctrl-bindings.txt
In order to match the current name of this file.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
|
|
As we move stuff around, some doc references are broken. Fix some of
them via this script:
./scripts/documentation-file-ref-check --fix
Manually checked that produced results are valid.
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
|
|
Pull pwm updates from Thierry Reding:
"This contains a couple of fixes and cleanups for the Meson and
ACPI/LPSS drivers as well as capture support for STM32.
Note that given the cross- subsystem changes, the STM32 patches were
merged through the MFD and PWM trees, both sharing an immutable
branch"
* tag 'pwm/for-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: stm32: Fix build warning with CONFIG_DMA_ENGINE disabled
pwm: stm32: Enforce dependency on CONFIG_MFD_STM32_TIMERS
ACPI / LPSS: Add missing prv_offset setting for byt/cht PWM devices
pwm: lpss: platform: Save/restore the ctrl register over a suspend/resume
dt-bindings: mfd: stm32-timers: Add support for dmas
pwm: simplify getting .drvdata
pwm: meson: Fix allocation of PWM channel array
|
|
Pull MFD updates from Lee Jones:
"New Device Support:
- Add support for AXP813 ADC to AXP20x
- Add support for PM8005, PM8998 and PMI8998
New Functionality:
- Add support for Battery Power Supply to AXP813
- Add support for SYSCON to SPARD SC27XX SPI
- Add support for RTC to ChromeOS Embedded-Controller
Fix-ups:
- Remove unused code; exynos{4,5}-pmu, cros_ec, cros_ec_acpi_gpe
- Remove duplicate error messages (-ENOMEM, etc); htc-i2cpld,
janz-cmodio, max8997, rc5t583, sm501, smsc-ece1099, abx500-core,
si476x-i2c, ti_am335x_tscadc, tps65090, tps6586x, tps65910,
tps80031, twl6030-irq, viperboard
- Succinctly use ptr to struct in sizeof(); rc5t583, abx500-core,
sm501, smsc-ece1099
- Simplify syntax for NULL ptr checking; abx500-core, sm501
- No not unnecessarily initialise variables; tps65910, tps65910
- Reorganise and simplify driver data; omap-usb-tll
- Move to SPDX license statement; tps68470
- Probe ADCs via DT; axp20x
- Use new GPIOD API; arizona-core
- Constify things; axp20x
- Reduce code-size (use MACROS, etc); axp20x, omap-usb-host
- Add DT support/docs; motorola-cpcap
- Remove VLAs; rave-sp
- Use devm_* managed resources; cros_ec
- Interrogate HW for firmware version; rave-sp
- Provide ACPI support for ChromeOS Embedded-Controller
Bug Fixes:
- Reorder ordered (enum) device list; tps65218
- Only accept valid data from the offset; rave-sp
- Refrain from copying junk from failed SPI read; cros_ec_dev
- Fix potential memory leaks; pcf50633-core
- Fix clock initialisation; twl-core
- Fix build-issue; tps65911
- Fix off-by-one error; tps65911
- Fix code ordering issues; intel-lpss
- Fix COMPILE_TEST related issues; pwm-stm32
- Fix broken MMC card detection; asic3
- Fix clocking related issues; intel-lpss-pci"
* tag 'mfd-next-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (84 commits)
mfd: cros_ec: Remove unused __remove function
mfd: wm97xx-core: Platform data can be NULL
mfd: cros_ec_dev: Don't advertise junk features on failure
mfd: cros_ec: Use devm_kzalloc for private data
mfd: intel-lpss: Fix Intel Cannon Lake LPSS I2C input clock
mfd: asic3: Fix broken MMC card detection
mfd: timberdale: Fix spelling mistake "Uknown" -> "Unknown"
mfd: omap-usb-host: Use match_string() helper
mfd: stm32-timers: Fix pwm-stm32 linker issue with COMPILE_TEST
pwm: stm32: Initialize raw local variables
mfd: arizona: Update DT doc to support more standard Reset binding
dt-bindings: mfd: Add bindings for DA9063L
mfd: intel-lpss: Correct names of RESETS register bits
mfd: qcom-spmi-pmic: Add support for pm8005, pm8998 and pmi8998
mfd: intel-lpss: Program REMAP register in PIO mode
mfd: cros_ec_i2c: Moving the system sleep pm ops to late
mfd: cros_ec_i2c: Add ACPI module device table
mfd: cros_ec_dev: Register shutdown function for debugfs
mfd: cros_ec_dev: Register cros-ec-rtc driver as a subdevice
mfd: cros_ec: Don't try to grab log when suspended
...
|
|
Specification of the bindings for the parent MFD driver component
of the Cirrus Logic Madera codec drivers.
Note that although the interrupt controller and GPIO are child
drivers their required bindings are trivial, mandatory, and exist
within the parent MFD node so are documented here.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Add device tree bindings for the Dialog DA9063L. This is a
variant of the DA9063 chip with smaller package, with less
LDO regulators and without RTC block. The other properties
of the chip are the same, including the content of the chip
ID register.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Add the compatibles and PMIC ids for the pm8005, pm8998, and pmi8998
PMICS found on MSM8998 and SDM845 based platforms.
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Add support for DMAs to STM32 timers. STM32 Timers can support up to 7
dma requests: up to 4 channels, update, compare and trigger.
DMAs may be used to transfer data from pwm capture for instance.
DMA support is made optional, PWM capture support is also an option.
This is much more wise system-wide to avoid shortage on DMA request
lines as there's significant amount of timer instances that can
request up to 7 channels.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This adds the DT binding for the audio-codec sub-module found
inside the Motorola CPCAP PMIC.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
|
|
Document the new optional properties related to DDR Backup Mode and
toggle/momentary power switches.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Like axp221, axp223, axp813 the axp803 is also supporting external
regulator to drive the OTG VBus through N_VBUSEN PMIC pin.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds documentation for device tree bindings for keys support
as the subnode of MT6397/MT6323 PMIC.
Signed-off-by: Chen Zhong <chen.zhong@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Pull ARM SoC driver updates from Arnd Bergmann:
"The main addition this time around is the new ARM "SCMI" framework,
which is the latest in a series of standards coming from ARM to do
power management in a platform independent way.
This has been through many review cycles, and it relies on a rather
interesting way of using the mailbox subsystem, but in the end I
agreed that Sudeep's version was the best we could do after all.
Other changes include:
- the ARM CCN driver is moved out of drivers/bus into drivers/perf,
which makes more sense. Similarly, the performance monitoring
portion of the CCI driver are moved the same way and cleaned up a
little more.
- a series of updates to the SCPI framework
- support for the Mediatek mt7623a SoC in drivers/soc
- support for additional NVIDIA Tegra hardware in drivers/soc
- a new reset driver for Socionext Uniphier
- lesser bug fixes in drivers/soc, drivers/tee, drivers/memory, and
drivers/firmware and drivers/reset across platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (87 commits)
reset: uniphier: add ethernet reset control support for PXs3
reset: stm32mp1: Enable stm32mp1 reset driver
dt-bindings: reset: add STM32MP1 resets
reset: uniphier: add Pro4/Pro5/PXs2 audio systems reset control
reset: imx7: add 'depends on HAS_IOMEM' to fix unmet dependency
reset: modify the way reset lookup works for board files
reset: add support for non-DT systems
clk: scmi: use devm_of_clk_add_hw_provider() API and drop scmi_clocks_remove
firmware: arm_scmi: prevent accessing rate_discrete uninitialized
hwmon: (scmi) return -EINVAL when sensor information is unavailable
amlogic: meson-gx-socinfo: Update soc ids
soc/tegra: pmc: Use the new reset APIs to manage reset controllers
soc: mediatek: update power domain data of MT2712
dt-bindings: soc: update MT2712 power dt-bindings
cpufreq: scmi: add thermal dependency
soc: mediatek: fix the mistaken pointer accessed when subdomains are added
soc: mediatek: add SCPSYS power domain driver for MediaTek MT7623A SoC
soc: mediatek: avoid hardcoded value with bus_prot_mask
dt-bindings: soc: add header files required for MT7623A SCPSYS dt-binding
dt-bindings: soc: add SCPSYS binding for MT7623 and MT7623A SoC
...
|
|
The LPC Host Interface Controller is part of a BMC SoC that is used for
communication with the host.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This describes the reset controller present in the LPC address space.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
[p.zabel@pengutronix.de: removed a space before tab in indent]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Pull ARM SoC device tree updates from Arnd Bergmann:
"We get a moderate number of new machines this time, and only one new
SoC variant (Actions S700):
Actions:
- S700 Soc and CubieBoard7 development board
- Allo.com Sparky Single-board-computer
Allwinner:
- Orange Pi R1 development board
- Libre Computer Board ALL-H3-CC H3 single-board computer
ASpeed ast2x00:
- Witherspoon: OpenPower Power9 server manufactured by IBM that uses the ASPEED ast2500
- Zaius: OpenPower Power9 server manufactured by Invatech that uses the ASPEED ast2500
- Q71L: Intel Xeon server manufactured by Qanta that uses the ASPEED ast2400
AT91:
- Axentia Nattis/Natte digital signage
- sama5d2 PTC-ek Evaluation board
Freescale/NXP i.MX:
- SolidRun Humminboard2 development board
- Variscite DART-MX6 SoM and Carrier-board
- Technologic TS-4600 and TS-7970 development board
- Toradex Colibri iMX7D SoM board
- v1.5 variant of Solidrun Cubox-i and Hummingboard
Freescale/NXP Layerscape:
- Moxa UC-8410A Series industrial computer
Gemini:
- D-Link DNS-313 NAS enclosure
OMAP:
- LogicPD OMAP35xx SOM-LV devkit
- LogicPD OMAP35xx Torpedo devkit
Renesas:
- r8a77970 (V3M) Starter Kit board
- r8a7795 (M3-W) Salvator-XS board
We finally managed to get the dtc warnings under control, with no more
build-time warnings for bad device tree files. This includes fixes for
the majority of platforms, including nomadik, samsung, lpc32xx, STi,
spear, mediatek, freescale, qcom, realview, keystone, omap, kirkwood,
renesas, hisilicon, and broadcom.
Files get rearranged on a few platforms, in particular the Marvell
Armada 7K/8K device tree files are changed in preparation for future
SoC support, based on more than two of the same chips in one package,
and some boards get renamed for oxnas for consistency.
Finally, many existing SoCs gain descriptions for additional on-chip
devices that we can now support with kernel drivers:
- Allwinner A83t (drm, ethernet, i2c, ...), H3/H5 (USB-OTG)
- Amlogic AXG family (clk, pinctrl, pwm, ...), and others (vpu, hdmi)
- Aspeed clk controller support
- Freescale LS1088A, LS1021A device support
- Gemini Ethernet, PCI, TVE, panel
- Keystone gpio, qspi, more uarts
- Mediatek cpufreq, regulator, clock, reset
- Marvell thermal, cpufreq, nand
- Renesas SMP, thermal, timer, PWM, sound, phy, ipmmu
- Rockchip Mipi, GPU, display
- Samsung Exynos5433 PMU, power domain, nfc
- Spreadtrum: sc9860 clocks
- Tegra TX2 PSDI, HDMI, I2C,SMMU, display, fuse, ..."
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (690 commits)
arm64: dts: stratix10: fix SPI settings
ARM: dts: socfpga: add i2c reset signals
arm64: dts: stratix10: add USB ECC reset bit
arm64: dts: stratix10: enable USB on the devkit
ARM: dts: socfpga: disable over-current for Arria10 USB devkit
ARM: dts: Nokia N9: add support for up/down keys in the dts
ARM: dts: nomadik: add interrupt-parent for clcd
ARM: dts: Add ethernet to a bunch of platforms
ARM: dts: Add ethernet to the Gemini SoC
ARM: dts: rename oxnas dts files
ARM: dts: s5pv210: add interrupt-parent for ohci
ARM: lpc3250: fix uda1380 gpio numbers
ARM: dts: STi: Add gpio polarity for "hdmi,hpd-gpio" property
ARM: dts: dra7: Reduce shut down temperature of non-cpu thermal zones
ARM: dts: n900: Add aliases for lcd and tvout displays
ARM: dts: Update ti-sysc data for existing users
ARM: dts: Fix smartreflex compatible for omap3 shared mpu-iva instance
arm64: dts: marvell: armada-80x0: Fix pinctrl compatible string
arm: spear13xx: Fix spics gpio controller's warning
arm: spear13xx: Fix dmas cells
...
|
|
Pull DeviceTree updates from Rob Herring:
- Convert to use memblock_virt_alloc in DT code which supports
bootmem arches. With this we can remove the arch specific
early_init_dt_alloc_memory_arch() functions.
- Enable running the DT unittests on UML
- Use SPDX license tags on DT files
- Fix early FDT kconfig ifdef logic
- Clean-up unittest Makefile
- Fix function comment for of_irq_parse_raw
- Add missing documentation for linux,initrd-{start,end} properties
- Clean-up of binding examples using uppercase hex
- Add trivial devices W83773G and Infineon TLV493D-A1B6
- Add missing STM32 SoC bindings
- Various small binding doc fixes
* tag 'devicetree-for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (23 commits)
xtensa: remove arch specific early DT functions
x86: remove arch specific early_init_dt_alloc_memory_arch
nios2: remove arch specific early_init_dt_alloc_memory_arch
mips: remove arch specific early_init_dt_alloc_memory_arch
metag: remove arch specific early DT functions
cris: remove arch specific early DT functions
libfdt: remove unnecessary include directive from <linux/libfdt.h>
of: unittest: refactor Makefile
of/fdt: use memblock_virt_alloc for early alloc
of: Use SPDX license tag for DT files
of/fdt: Fix #ifdef dependency of early flattree declarations
dt-bindings: h8300 clocksource: correct spelling of pulse
dt-bindings: imx6q-pcie: Add required property for i.MX6SX
mmc: Don't reference Linux-specific OF_GPIO_ACTIVE_LOW flag in DT binding
dt-bindings: Use lower case hex in unit-addresses
dt-bindings: display: panel: Fix compatible string for Toshiba LT089AC29000
dt-bindings: Add Infineon TLV493D-A1B6
dt-bindings: mailbox: ti,message-manager: Fix interrupt name error
dt-bindings: chosen: Document linux,initrd-{start,end}
dt-bindings: arm: document supported STM32 SoC family
...
|
|
Pull regmap updates from Mark Brown:
"A very busy release for regmap, all fairly specialist stuff but
useful:
- Support for disabling locking from Bartosz Golaszewski, allowing
users that handle their own locking to save some overhead.
- Support for hwspinlocks in syscons in MFD from Baolin Wang, this is
going through the regmap tree since the first users turned up some
some cases that needed interface tweaks with 0 being used as a
syscon identifier.
- Support for devices with no read or write flag from Andrew F.
Davis.
- Basic support for devices on SoundWire buses from Vinod Koul"
* tag 'regmap-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
mfd: syscon: Add hardware spinlock support
regmap: Allow empty read/write_flag_mask
regcache: flat: Un-inline index lookup from cache access
regmap: Add SoundWire bus support
regmap: Add one flag to indicate if a hwlock should be used
regmap: debugfs: document why we don't create the debugfs entries
regmap: debugfs: emit a debug message when locking is disabled
regmap: use proper part of work_buf for storing val
regmap: potentially duplicate the name string stored in regmap
regmap: Disable debugfs when locking is disabled
regmap: rename regmap_lock_unlock_empty() to regmap_lock_unlock_none()
regmap: allow to disable all locking mechanisms
regmap: Remove the redundant config to select hwspinlock
|
|
Pull MFD updates from Lee Jones:
"New Drivers:
- Add support for RAVE Supervisory Processor
Moved drivers:
- Move Realtek Card Reader Driver to Misc
New Device Support:
- Add support for Pinctrl to axp20x
New Functionality:
- Add resume support to atmel-flexcom
Fix-ups:
- Split MFD (mfd) and userspace handlers (platform) in cros_ec
- Fix trivial (whitespace, spelling) issue(s) in pcf50633-core
- Clean-up error handling in ab8500-debugfs
- General tidying up in tmio_core
- Kconfig fix-ups for qcom-pm8xxx
- Licensing changes (SPDX) to stm32-lptimer, stm32-timers
- Device Tree fixups in mc13xxx
- Simplify/remove unused code in cros_ec_spi, axp20x, ti_am335x_tscadc,
kempld-core, intel_soc_pmic_core.c, ab8500-debugfs"
* tag 'mfd-next-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (32 commits)
mfd: lpc_ich: Do not touch SPI-NOR write protection bit on Apollo Lake
mfd: axp20x: Mark axp288 CHRG_BAK_CTRL register volatile
mfd: ab8500: Introduce DEFINE_SHOW_ATTRIBUTE() macro
atmel_flexcom: Support resuming after a chip reset
mfd: Remove duplicate includes
dt-bindings: mfd: mc13xxx: Add the unit address to sysled
mfd: stm32: Adopt SPDX identifier
mfd: axp20x: Add pinctrl cell for AXP813
mfd: pm8xxx: Make elegible for COMPILE_TEST
mfd: kempld-core: Use resource_size function on resource object
mfd: tmio: Move register macros to tmio_core.c
mfd: cros ec: spi: Simplify delay handling between SPI messages
mfd: palmas: Assign the right powerhold mask for tps65917
mfd: ab8500-debugfs: Use common error handling code in ab8500_print_modem_registers()
mfd: ti_am335x_tscadc: Remove redundant assignment to node
mfd: pcf50633: Fix spelling mistake: 'Falied' -> 'Failed'
dt-bindings: watchdog: Add bindings for RAVE SP watchdog driver
watchdog: Add RAVE SP watchdog driver
mfd: Add driver for RAVE Supervisory Processor
serdev: Introduce devm_serdev_device_open()
...
|
|
|
|
Some system control registers need hardware spinlock to synchronize
between the multiple subsystems, so we should add hardware spinlock
support for syscon.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
As the 'reg' property is mandatory in the subnodes, improve the
example by adding the unit address to the sysled node.
This prevents the following build warning with W=1:
Node /soc/aips@70000000/spba@70000000/ecspi@70010000/pmic@0/leds/sysled0 has a reg or ranges property, but no unit name
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
DT for 4.16
- New boards:
- Axentia Nattis with Natte power
- sama5d2 PTC ek
- Document and use extended TCB bindings
* tag 'at91-ab-4.16-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (50 commits)
ARM: dts: at91: sama5d2_ptc_ek: use TCB0 as timers
ARM: dts: at91: sama5d27_som1_ek: use TCB0 as timers
ARM: dts: at91: sama5d2 Xplained: use TCB0 as timers
ARM: dts: at91: sama5d2: TC blocks are also simple-mfd and syscon devices
ARM: dts: at91: vinco: use TCB2 as timers
ARM: dts: at91: ma5d4: use TCB2 as timers
ARM: dts: at91: sama5d4 Xplained: use TCB2 as timers
ARM: dts: at91: sama5d4ek: use TCB2 as timers
ARM: dts: at91: sama5d4: Add TCB2
ARM: dts: at91: sama5d4: TC blocks are also simple-mfd and syscon devices
ARM: dts: at91: linea/tse850-3: use TCB0 as timers
ARM: dts: at91: sama5d3xek_cmp: use TCB0 as timers
ARM: dts: at91: kizbox2: use TCB0 as timers
ARM: dts: at91: sama5d3 Xplained: use TCB0 as timers
ARM: dts: at91: sama5d3xek: use TCB0 as timers
ARM: dts: at91: sama5d3: TC blocks are also simple-mfd and syscon devices
ARM: dts: at91: kizboxmini: use TCB0 as timers
ARM: dts: at91: cosino: use TCB0 as timers
ARM: dts: at91: acme/g25: use TCB0 as timers
ARM: dts: at91: at91sam9x5cm: use TCB0 as timers
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The current binding for the TCB is not flexible enough for some use cases
and prevents proper utilization of all the channels.
Acked-by: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
DT unit addresses should be lower case hex. Fix all the
binding examples.
Converted with the following command from Krzysztof Kozlowski:
sed -e 's/@\([a-fA-F0-9_-]*\) {/@\L\1 {/' -i $(find Documentation/devicetree/bindings -name '*.txt')
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Improve the binding example by removing all the leading 0x to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
Converted using the following command:
find Documentation/devicetree/bindings -name "*.txt" -exec sed -i -e 's/([^ ])\@0x([0-9a-f])/$1\@$2/g' {} +
This is a follow up to commit 48c926cd3414
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Pull MFD updates from Lee Jones:
"New drivers:
- Add support for Cherry Trail Dollar Cove TI PMIC
- Add support for Add Spreadtrum SC27xx series PMICs
New device support:
- Add support Regulator to axp20x
New functionality:
- Add DT support; aspeed-scu sc27xx-pmic
- Add power saving support; rts5249
Fix-ups:
- DT clean-up/rework; tps65217, max77693, iproc-cdru, iproc-mhb, tps65218
- Staticise/constify; stw481x
- Use new succinct IRQ API; fsl-imx25-tsadc
- Kconfig fix-ups; MFD_TPS65218
- Identify SPI method; lpc_ich
- Use managed resources (devm_*) calls; ssbi
- Remove unused/obsolete code/documentation; mc13xxx
Bug fixes:
- Fix typo in MAINTAINERS
- Fix error handling; mxs-lradc
- Clean-up IRQs on .remove; fsl-imx25-tsadc"
* tag 'mfd-next-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (21 commits)
dt-bindings: mfd: mc13xxx: Remove obsolete property
mfd: axp20x: Add axp20x-regulator cell for AXP813
mfd: Add Spreadtrum SC27xx series PMICs driver
dt-bindings: mfd: Add Spreadtrum SC27xx PMIC documentation
mfd: ssbi: Use devm_of_platform_populate()
mfd: fsl-imx25: Clean up irq settings during removal
mfd: mxs-lradc: Fix error handling in mxs_lradc_probe()
mfd: lpc_ich: Avoton/Rangeley uses SPI_BYT method
mfd: tps65218: Introduce dependency on CONFIG_OF
mfd: tps65218: Correct the config description
MAINTAINERS: Fix Dialog search term for watchdog binding file
mfd: fsl-imx25: Set irq handler and data in one go
mfd: rts5249: Add support for RTS5250S power saving
ACPI / PMIC: Add opregion driver for Intel Dollar Cove TI PMIC
mfd: Add support for Cherry Trail Dollar Cove TI PMIC
syscon: dt-bindings: Add binding document for iProc MHB block
syscon: dt-bindings: Add binding doc for Broadcom iProc CDRU
mfd: max77693: Add muic of_compatible in mfd_cell
mfd: stw481x: Make three arrays static const, reduces object code size
mfd: tps65217: Introduce dependency on CONFIG_OF
...
|
|
Pull DeviceTree updates from Rob Herring:
"A bigger diffstat than usual with the kbuild changes and a tree wide
fix in the binding documentation.
Summary:
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing
memory leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node.
The prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to
dtb compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage
Technology, shimafuji, Tecon Microprocessor Technologies, DH
electronics GmbH, Opal Kelly, and Next Thing"
* tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (55 commits)
dt-bindings: usb: add #phy-cells to usb-nop-xceiv
dt-bindings: Remove leading zeros from bindings notation
kbuild: handle dtb-y and CONFIG_OF_ALL_DTBS natively in Makefile.lib
MIPS: dts: remove bogus bcm96358nb4ser.dtb from dtb-y entry
kbuild: clean up *.dtb and *.dtb.S patterns from top-level Makefile
.gitignore: move *.dtb and *.dtb.S patterns to the top-level .gitignore
.gitignore: sort normal pattern rules alphabetically
dt-bindings: add vendor prefix for Next Thing Co.
scripts/dtc: Update to upstream version v1.4.5-6-gc1e55a5513e9
of: dynamic: fix memory leak related to properties of __of_node_dup
of: overlay: make pr_err() string unique
of: overlay: pr_err from return NOTIFY_OK to overlay apply/remove
of: overlay: remove unneeded check for NULL kbasename()
of: overlay: remove a dependency on device node full_name
of: overlay: simplify applying symbols from an overlay
of: overlay: avoid race condition between applying multiple overlays
of: overlay: loosen overly strict phandle clash check
of: overlay: expand check of whether overlay changeset can be removed
of: overlay: detect cases where device tree may become corrupt
of: overlay: minor restructuring
...
|
|
Improve the binding example by removing all the leading zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find ./Documentation/devicetree/bindings "*.txt"`
Some unnecessary changes were manually fixed.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The 'fsl,spi-num-chipselects' property is obsolete according to
Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt, so remove
it from the example.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch adds the binding documentation for Spreadtrum SC27xx series
PMIC device.
Signed-off-by: Baolin Wang <baolin.wang@spreadtrum.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Add binding document for Broadcom iProc's Multi-Host Bridge (MHB)
block
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
Olliver Schinagl
Linus Torvalds
Matti Vaittinen
Charles Keepax
Lee Jones
Radu Pirea
Marcel Ziswiler
Chen-Yu Tsai
Christoph Fritz
Rob Herring
Mauro Carvalho Chehab
Richard Fitzgerald
Marek Vasut
Stephen Boyd
Fabrice Gasnier
Sebastian Reichel
Mark Brown
Geert Uytterhoeven
Jagan Teki
Chen Zhong
Joel Stanley
Baolin Wang
Fabio Estevam
Olof Johansson
Alexandre Belloni
Mathieu Malaterre
Marco Franchi
Baolin Wang
Ray Jui