| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Extend the bindings to cover the set of features found in Tegra194.
Note that, technically, there are four more supplies connected to the
XUSB pad controller (DVDD_PEX, DVDD_PEX_PLL, HVDD_PEX and HVDD_PEX_PLL)
, but the power sequencing requirements of Tegra194 require these to be
under the control of the PMIC.
Tegra194 XUSB PADCTL supports up to USB 3.1 Gen 2 speed, however, it
is possible for some platforms have long signal trace that could not
provide sufficient electrical environment for Gen 2 speed. This patch
adds a "maximum-speed" property to usb3 ports which can be used to
specify the maximum supported speed for any particular USB 3.1 port.
For a port that is not capable of SuperSpeedPlus, "maximum-speed"
property should carry "super-speed".
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Minor overlapping changes, nothing serious.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 93512dad334d ("dt-bindings: Improve validation build error
handling"), 'make dtbs_check' does not validate the schema fully.
If you want to check everything, you need to run two commands separately.
$ make ARCH=arm dt_binding_check
$ make ARCH=arm dtbs_check
They are exclusive each other, so you cannot do like this:
$ make ARCH=arm dt_binding_check dtbs_check
In this case, dt-doc-validate and dt-extract-example are skipped
because CHECK_DTBS is set.
Let's make it possible to run these two targets in a single command.
It will be useful for schema writers.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
|
|
Pull networking fixes from David Miller:
"It looks like a decent sized set of fixes, but a lot of these are one
liner off-by-one and similar type changes:
1) Fix netlink header pointer to calcular bad attribute offset
reported to user. From Pablo Neira Ayuso.
2) Don't double clear PHY interrupts when ->did_interrupt is set,
from Heiner Kallweit.
3) Add missing validation of various (devlink, nl802154, fib, etc.)
attributes, from Jakub Kicinski.
4) Missing *pos increments in various netfilter seq_next ops, from
Vasily Averin.
5) Missing break in of_mdiobus_register() loop, from Dajun Jin.
6) Don't double bump tx_dropped in veth driver, from Jiang Lidong.
7) Work around FMAN erratum A050385, from Madalin Bucur.
8) Make sure ARP header is pulled early enough in bonding driver,
from Eric Dumazet.
9) Do a cond_resched() during multicast processing of ipvlan and
macvlan, from Mahesh Bandewar.
10) Don't attach cgroups to unrelated sockets when in interrupt
context, from Shakeel Butt.
11) Fix tpacket ring state management when encountering unknown GSO
types. From Willem de Bruijn.
12) Fix MDIO bus PHY resume by checking mdio_bus_phy_may_suspend()
only in the suspend context. From Heiner Kallweit"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (112 commits)
net: systemport: fix index check to avoid an array out of bounds access
tc-testing: add ETS scheduler to tdc build configuration
net: phy: fix MDIO bus PM PHY resuming
net: hns3: clear port base VLAN when unload PF
net: hns3: fix RMW issue for VLAN filter switch
net: hns3: fix VF VLAN table entries inconsistent issue
net: hns3: fix "tc qdisc del" failed issue
taprio: Fix sending packets without dequeueing them
net: mvmdio: avoid error message for optional IRQ
net: dsa: mv88e6xxx: Add missing mask of ATU occupancy register
net: memcg: fix lockdep splat in inet_csk_accept()
s390/qeth: implement smarter resizing of the RX buffer pool
s390/qeth: refactor buffer pool code
s390/qeth: use page pointers to manage RX buffer pool
seg6: fix SRv6 L2 tunnels to use IANA-assigned protocol number
net: dsa: Don't instantiate phylink for CPU/DSA ports unless needed
net/packet: tpacket_rcv: do not increment ring index on drop
sxgbe: Fix off by one in samsung driver strncpy size arg
net: caif: Add lockdep expression to RCU traversal primitive
MAINTAINERS: remove Sathya Perla as Emulex NIC maintainer
...
|
|
Convert the usb-connector.txt bindings file to YAML format. This allows
it to be used in dt_bindings_check verification. This patch was
born out of a patch series for the addition of a Type C connector
class port driver[1].
An attempt has been made to maintain the same documentation text and
example structure as was in the .txt file, but wherever needed
modifications have been made to satisfy dt_bindings_check.
Also, update all references to usb-connector.txt to now use
usb-connector.yaml.
[1]: https://lkml.org/lkml/2020/2/19/1232
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The Amlogic G12A SPICC controllers uses a secondary clock used to feed the
baud rate generator and the delay control logic.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200312133131.26430-9-narmstrong@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Kryo280 is found in msm8998, so add it to the list of cpu compatibles.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The description below is already in use for px30.dtsi,
but was somehow never added to a document, so add
"rockchip,px30-i2c", "rockchip,rk3399-i2c"
for i2c nodes on a px30 platform to i2c-rk3x.yaml.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The description below is already in use for rk3308.dtsi,
but was somehow never added to a document, so add
"rockchip,rk3308-i2c", "rockchip,rk3399-i2c"
for i2c nodes on a rk3308 platform to i2c-rk3x.yaml.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The description below is already in use for rk3368.dtsi,
but was somehow never added to a document, so add
"rockchip,rk3368-i2c", "rockchip,rk3288-i2c"
for i2c nodes on a rk3368 platform to i2c-rk3x.yaml.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The description below is already in use for rk3036.dtsi,
but was somehow never added to a document, so add
"rockchip,rk3036-i2c", "rockchip,rk3288-i2c"
for i2c nodes on a rk3036 platform to i2c-rk3x.yaml.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Current dts files with 'i2c' nodes are manually verified.
In order to automate this process i2c-rk3x.txt
has to be converted to yaml. In the new setup
i2c-rk3x.yaml will inherit properties from
i2c-controller.yaml.
Also change document name in MAINTAINERS.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Document the optional binding to limit the possible sdtv standards on the
input connectors.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Use underlines to highlight optional and required properties. This is
quite common for all bindings. Align descriptions and start sentence
with uppercase letter. Also reword the usage of the required
endpoint properties for the output port in case BT.656 should be used.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The TVP5150/1 decoders support different video input sources to their
AIP1A/B pins.
Possible configurations are as follows:
- Analog Composite signal connected to AIP1A.
- Analog Composite signal connected to AIP1B.
- Analog S-Video Y (luminance) and C (chrominance)
signals connected to AIP1A and AIP1B respectively.
This patch extends the device tree bindings documentation to describe
how the input connectors for these devices should be defined in a DT.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Some connectors no matter if in- or output supports only a limited
range of sdtv standards. It doesn't matter if the hardware behind that
connector supports more than the listed formats since the users are
restriced by a label e.g. to plug only a camera into this connector
which uses the PAL format.
This patch adds the capability to describe such limitation within the
firmware. There are no format restrictions if the property isn't
present, so it's completely backward compatible.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Extra dtc warnings (roughly what W=1 enables) are now enabled by default
when building the binding examples. These were fixed treewide in
5.6-rc5, but the newly added google,cros-ec-codec schema adds some new
warnings:
Documentation/devicetree/bindings/sound/google,cros-ec-codec.example.dts:17.28-21.11:
Warning (unit_address_vs_reg): /example-0/reserved_mem: node has a reg or ranges property, but no unit name
Documentation/devicetree/bindings/sound/google,cros-ec-codec.example.dts:22.19-32.11:
Warning (unit_address_vs_reg): /example-0/cros-ec@0: node has a unit name, but no reg property
Documentation/devicetree/bindings/sound/google,cros-ec-codec.example.dts:26.37-31.15:
Warning (unit_address_vs_reg): /example-0/cros-ec@0/ec-codec: node has a reg or ranges property, but no unit name
Fixing the above, then results in:
Documentation/devicetree/bindings/sound/google,cros-ec-codec.example.dts:26.13-23:
Warning (reg_format): /example-0/cros-ec@0:reg: property has invalid length (4 bytes) (#address-cells == 1, #size-cells == 1)
Documentation/devicetree/bindings/sound/google,cros-ec-codec.example.dts:27.37-32.15:
Warning (unit_address_vs_reg): /example-0/cros-ec@0/ec-codec: node has a reg or ranges property, but no unit name
Fixes: eadd54c75f1e ("dt-bindings: Convert the binding file google, cros-ec-codec.txt to yaml format.")
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Cc: alsa-devel@alsa-project.org
Cc: Benson Leung <bleung@chromium.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Guenter Roeck <groeck@chromium.org>
Cc: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Cc: Cheng-Yi Chiang <cychiang@chromium.org>
Link: https://lore.kernel.org/r/20200311205841.2710-1-robh@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If the kernel configuration option CONFIG_PCIE_DW_PLAT_HOST is enabled
then this can cause the kernel to incorrectly probe the generic
designware PCIe platform driver instead of the Tegra194 designware PCIe
driver. This causes a boot failure on Tegra194 because the necessary
configuration to access the hardware is not performed.
The order in which the compatible strings are populated in Device-Tree
is not relevant in this case, because the kernel will attempt to probe
the device as soon as a driver is loaded and if the generic designware
PCIe driver is loaded first, then this driver will be probed first.
Therefore, to fix this problem, remove the "snps,dw-pcie" string from
the compatible string as we never want this driver to be probe on
Tegra194.
Fixes: 2602c32f15e7 ("arm64: tegra: Add P2U and PCIe controller nodes to Tegra194 DT")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add thermal binding doc for Freescale's i.MX8MM Thermal Monitoring Unit.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1582947862-11073-1-git-send-email-Anson.Huang@nxp.com
|
|
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Link: https://lore.kernel.org/r/20200308214230.15193-1-j.neuschaefer@gmx.net
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
NXP i.MX8QXP is an ARMv8 SoC with a Cortex-M4 core inside as
system controller, the system controller is in charge of system
power, clock and thermal sensors etc. management, Linux kernel
has to communicate with system controller via MU (message unit)
IPC to get temperature from thermal sensors, this patch adds
binding doc for i.MX system controller thermal driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1582330132-13461-1-git-send-email-Anson.Huang@nxp.com
|
|
Add the Spreadtrum thermal documentation.
Signed-off-by: Baolin Wang <baolin.wang@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/444e45ce0a9b390b2502dfcefd1ddb36948fa8e1.1582013101.git.baolin.wang7@gmail.com
|
|
Add the LS1028A SoC compatibility string to the lpuart devicetree
bindings documentation.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200307091302.14881-1-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add documentation for the devicetree bindings of the
Ingenic JZ4770 USB transceiver.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200229161820.17824-1-paul@crapouillou.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The definitions for the "qcom,smem-states" and "qcom,smem-state-names"
properties need to list their "$ref" under an "allOf" keyword.
In addition, fix two problems in the example at the end:
- Use #include for header files that define needed symbolic values
- Terminate the line that includes the "ipa-shared" register space
name with a comma rather than a semicolon
Finally, update some white space in the example for better alignment.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add ipq806x to compatible list in qcom_scm Documentation
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20200311130918.753-2-ansuelsmth@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
drm-misc-next for 5.7:
UAPI Changes:
Cross-subsystem Changes:
Core Changes:
Driver Changes:
- fb-helper: Remove drm_fb_helper_{add,add_all,remove}_one_connector
- fbdev: some cleanups and dead-code removal
- Conversions to simple-encoder
- zero-length array removal
- Panel: panel-dpi support in panel-simple, Novatek NT35510, Elida
KD35T133,
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20200309135439.dicfnbo4ikj4tkz7@gilmour
|
|
spi: Rewrite mtk-quadspi spi-nor driver with spi-mem
This patchset from Chuanhong Guo <gch981213@gmail.com> adds a spi-mem
driver for Mediatek SPI-NOR controller, which already has limited
support by mtk-quadspi. This new driver can make use of full quadspi
capability of this controller.
|
|
spi-mtk-nor is a driver to replace mtk-quadspi and they have almost
the same device-tree bindings. Reuse this binding documentation and
convert it for new driver:
1. "Mediatek SoCs" -> "Mediatek ARM SoCs" because MTK MIPS SoCs
use different controllers.
2. document "interrupts" as a required property because it's
available on all SoCs with this controller and new driver takes
advantages of it. It's implemented as optional only to maintain
backward compatibility.
3. add a dummy interrupt binding in example.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Link: https://lore.kernel.org/r/20200306085052.28258-4-gch981213@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Linux 5.6-rc5
|
|
Convert the STM32 SPDIFRX bindings to DT schema format using json-schema.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200117170352.16040-1-olivier.moysan@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Adding support for EBI DMA unit (EDU).
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200122213313.35820-2-kdasu.kdev@gmail.com
|
|
Document the bindings used by the Macronix NAND device.
Signed-off-by: Mason Yang <masonccyang@mxic.com.tw>
Reviewed-by: Rob Herring <robh@kernel.org>
[<miquel.raynal@bootlin.com: Fix typos]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1581922600-25461-3-git-send-email-masonccyang@mxic.com.tw
|
|
The A33 SS has a difference with all other SS, it give SHA1 digest
directly in BE.
This difference need to be handlded by the driver and so need a new
compatible.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
Convert cirrus,cs42l51 to yaml format.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200228152706.29749-1-benjamin.gaignard@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add support for PCIe controllers that can operate in endpoint mode
in Tegra194.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
|
|
i.MX6UL example uses a specific node name for the crypto node.
Let's fix it so we avoid this propagating further.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
crypto node should use the "crypto" generic naming,
and not the "dcp" specific one.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
crypto node should use the "crypto" generic naming,
and not a specific one.
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
A test with the command below gives this error:
arch/arm/boot/dts/rk3036-evb.dt.yaml: /: compatible:
['rockchip,rk3036-evb', 'rockchip,rk3036']
is not valid under any of the given schemas
This board was somehow never added to the documentation.
Fix this error by adding the rk3036-evb board to rockchip.yaml.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/arm/rockchip.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200302092759.3291-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
A test with the command below gives this error:
arch/arm/boot/dts/rk3036-kylin.dt.yaml: /: compatible:
['rockchip,rk3036-kylin', 'rockchip,rk3036']
is not valid under any of the given schemas
Normally the dt-binding is the authoritative part, so boards should follow
the binding, but in the kylin-case the compatible from the .dts is used for
years in the field now, so fix the binding, as otherwise
we would break old users.
Fix this error by changing 'rockchip,kylin-rk3036' to
'rockchip,rk3036-kylin' in rockchip.yaml.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/arm/rockchip.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200302092759.3291-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Convert the Renesas Clock Pulse Generator / Module Standby and Software
Reset Device Tree binding documentation to json-schema.
Note that #reset-cells was incorrecty marked a required property for
RZ/A2 before.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200303094848.23670-1-geert+renesas@glider.be
|
|
Convert Renesas R-Car VIN bindings documentation to json-schema.
As the examples in the bindings now can be tested add a new one which
describes how the both a parallel and a CSI-2 source can be connected on
Gen3 SoCs.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Requested my mripard for some misc patches that need this as a base.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Add binding for the idk-2121wr LVDS panel from Advantech.
Some panel-specific documentation can be found here:
https://buy.advantech.eu/Displays/Embedded-LCD-Kits-High-Brightness/model-IDK-2121WR-K2FHA2E.htm
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1583869169-1006-1-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
|
|
Consolidate and move the 'secondary-boot-reg' property from the 3
existing binding documents into the main cpus.yaml documentation, also
make sure that the property is enforced when relevant.
Acked-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Update Vulcan SoC family binding document for boards/SoCs to use YAML.
Verified with dt_binding_check and dtbs_check.
Acked-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Update the Broadcom BCM11351 SoC family binding document for boards/SoCs
to use YAML. Verified with dt_binding_check and dtbs_check.
Acked-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Update the Broadcom BCM4708 SoC family binding document for boards/SoCs
to use YAML. Verified with dt_binding_check and dtbs_check.
Acked-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Update the Broadcom BCM23550 SoC binding document for boards/SoCs to use
YAML. Verified with dt_binding_check and dtbs_check.
Acked-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
JC Kuo
David S. Miller
Masahiro Yamada
Linus Torvalds
Prashant Malani
Neil Armstrong
Amit Kucheria
Johan Jonker
Marco Felsch
Rob Herring
Jon Hunter
Anson Huang
Jonathan Neuschäfer
Baolin Wang
Michael Walle
Paul Cercueil
Alex Elder
Ansuel Smith
Dave Airlie
Mark Brown
Chuanhong Guo
Olivier Moysan
Kamal Dasu
Mason Yang
Corentin Labbe
Benjamin Gaignard
Vidya Sagar
Horia Geantă
Geert Uytterhoeven
Niklas Söderlund
Fabrizio Castro
Florian Fainelli