| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add support for Texas Instruments TMP464 and TMP468 temperature sensor
ICs.
TI's TMP464 is an I2C temperature sensor chip. This chip is similar
to TI's TMP421 chip, but with 16bit-wide registers (instead of
8bit-wide registers). The chip has one local sensor and four remote
sensors. TMP468 is similar to TMP464 but has one local and eight
remote sensors.
Originally-from: Agathe Porte <agathe.porte@nokia.com>
Cc: Agathe Porte <agathe.porte@nokia.com>
Cc: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Tested-by: Agathe Porte <agathe.porte@nokia.com>
Link: https://lore.kernel.org/r/20220222223610.23098-2-linux@roeck-us.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for another Infineon Multi-phase controller chip. The
xdpe11280 uses linear instead of vid data format for VOUT. Detect
VOUT_MODE format during identification and skip the xdpe122 related
adaptions in case it is linear.
Signed-off-by: Marcello Sylvester Bauer <sylv@sylv.io>
Link: https://lore.kernel.org/r/fa6a4b636a05ecb337d132824efca2545188a2a2.1646214248.git.sylv@sylv.io
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Extend aquacomputer_d5next driver to expose hardware temperature sensors
of the Aquacomputer Farbwerk 360 RGB controller, which communicates through
a proprietary USB HID protocol.
Four temperature sensors are available. Additionally, serial number and
firmware version are exposed through debugfs.
This driver has been tested on x86_64.
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
After doing some research, it seems that Fujitsu's
hardware monitoring solution exports data describing
which temperature sensors affect which fans, similar
to the data in fan_source of the ftsteutates driver.
Writing 0 into these registers forces the fans to
full speed.
Export this data with standard attributes.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20220224061210.16452-3-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The TMP125 is a 2 degree Celsius accurate Digital
Temperature Sensor with a SPI interface.
The temperature register is a 16-bit, read-only register.
The MSB (Bit 15) is a leading zero and never set. Bits 14
to 5 are the 1+9 temperature data bits in a two's
complement format. Bits 4 to 0 are useless copies of
Bit 5 value and therefore ignored.
This was tested on a Aerohive HiveAP-350.
Bonus: lm70 supports TMP122/TMP124 as well.
I added them to the Kconfig module description.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Link: https://lore.kernel.org/r/43b19cbd4e7f51e9509e561b02b5d8d0e7079fac.1645175187.git.chunkeey@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
PLI1209BC is a Digital Supervisor from Vicor Corporation.
Signed-off-by: Marcello Sylvester Bauer <sylv@sylv.io>
Link: https://lore.kernel.org/r/4e016e66275bc46c90974aec18b150c874e64787.1645435888.git.sylv@sylv.io
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Document the SMM interface as requested by Pali Rohar.
Since Dell does not offer any offical documentation
regarding the SMM interface, the necessary information
was extracted from the dell_smm_hwmon driver and other
sources.
Suggested-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20220215191113.16640-7-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
A user discovered [1] the CPU Core voltage sensor, which spans 2
registers and provides output in mV. Althroug the discovery was made
with a X470 chipset, the sensor is present in X570 (tested with C8H).
For now simply add it to each board with the CPU current sensor present.
[1] https://github.com/zeule/asus-ec-sensors/issues/12
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Tested-by: Denis Pauk <pauk.denis@gmail.com>
Link: https://lore.kernel.org/r/20220208094244.1106312-1-eugene.shalygin@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The Wi-Fi variant of Crosshair VIII Hero provides the same sensors,
which was tested by a Libre Hardware Monitor user [1].
[1] https://github.com/LibreHardwareMonitor/LibreHardwareMonitor/pull/453#issuecomment-1028398487
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20220203203052.441712-1-eugene.shalygin@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The old Datasheet does not exist anymore.
Signed-off-by: Marcello Sylvester Bauer <sylv@sylv.io>
Link: https://lore.kernel.org/r/76025f40d2684dc0d3ec02c8899b726b07a0e7da.1643299570.git.sylv@sylv.io
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Link: https://lore.kernel.org/r/20220124015658.687309-3-eugene.shalygin@gmail.com
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Tested-by: Denis Pauk <pauk.denis@gmail.com>
[groeck: update index.rst, do not drop asus_wmi_ec_sensors.rst]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add the "label" sysfs attribute, which can contain a descriptive label
that allows to uniquely identify a device within the system.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220110182256.30763-2-paul@crapouillou.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add documentation for peci-cputemp driver that provides DTS thermal
readings for CPU packages and CPU cores, and peci-dimmtemp driver that
provides Temperature Sensor on DIMM readings.
Co-developed-by: Iwona Winiarska <iwona.winiarska@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Iwona Winiarska <iwona.winiarska@intel.com>
Link: https://lore.kernel.org/r/20220208153639.255278-13-iwona.winiarska@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is a multi-function device to interface with the sy7636a
EPD PMIC chip from Silergy.
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The IR38060, IR38164 and IR38263 can be supported using this driver.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Arthur Heymans <arthur.heymans@9elements.com>
Link: https://lore.kernel.org/r/20211213142814.264802-2-arthur.heymans@9elements.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This driver implements monitoring and control of fans plugged into the
device. Besides typical speed monitoring and PWM duty cycle control,
voltage and current are reported for every fan.
The device also has 2 connectors for RGB LEDs, support for them isn't
implemented (mainly because there is no standardized sysfs interface).
Also, the device has a noise sensor, but the sensor seems to be completely
useless (and very imprecise), so support for it isn't implemented too.
The driver coexists with userspace tools that access the device through
hidraw interface with no known issues.
The driver has been tested on x86_64, built in and as a module.
Some changes/improvements were suggested by Jonas Malaco.
Signed-off-by: Aleksandr Mezin <mezin.alexander@gmail.com>
Link: https://lore.kernel.org/r/20211031033058.151014-1-mezin.alexander@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for mp5023 device from Monolithic Power Systems, Inc. (MPS)
vendor. This is a Hot-Swap Controller.
Signed-off-by: Howard Chiu <howard.chiu@quantatw.com>
Link: https://lore.kernel.org/r/HKAPR04MB400349AA406694FB976D78D096709@HKAPR04MB4003.apcprd04.prod.outlook.com
[groeck: Added MODULE_IMPORT_NS, entry in index.rst]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Provides a Linux kernel module "asus_wmi_sensors" that provides sensor
readouts via ASUS' WMI interface present in the UEFI of
X370/X470/B450/X399 Ryzen motherboards.
Supported motherboards:
* ROG CROSSHAIR VI HERO,
* PRIME X399-A,
* PRIME X470-PRO,
* ROG CROSSHAIR VI EXTREME,
* ROG CROSSHAIR VI HERO (WI-FI AC),
* ROG CROSSHAIR VII HERO,
* ROG CROSSHAIR VII HERO (WI-FI),
* ROG STRIX B450-E GAMING,
* ROG STRIX B450-F GAMING,
* ROG STRIX B450-I GAMING,
* ROG STRIX X399-E GAMING,
* ROG STRIX X470-F GAMING,
* ROG STRIX X470-I GAMING,
* ROG ZENITH EXTREME,
* ROG ZENITH EXTREME ALPHA.
Co-developed-by: Ed Brindley <kernel@maidavale.org>
Signed-off-by: Ed Brindley <kernel@maidavale.org>
Signed-off-by: Denis Pauk <pauk.denis@gmail.com>
[groeck: Squashed:
"hwmon: Fix warnings in asus_wmi_sensors.rst documetation."]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Linux HWMON sensors driver for ASUS motherboards to read
sensors from the embedded controller.
Many ASUS motherboards do not publish all the available
sensors via the Super I/O chip but the missing ones are
available through the embedded controller (EC) registers.
This driver implements reading those sensor data via the
WMI method BREC, which is known to be present in all ASUS
motherboards based on the AMD 500 series chipsets (and
probably is available in other models too). The driver
needs to know exact register addresses for the sensors and
thus support for each motherboard has to be added explicitly.
The EC registers do not provide critical values for the
sensors and as such they are not published to the HWMON.
Supported motherboards:
* PRIME X570-PRO
* Pro WS X570-ACE
* ROG CROSSHAIR VIII HERO
* ROG CROSSHAIR VIII DARK HERO
* ROG CROSSHAIR VIII FORMULA
* ROG STRIX X570-E GAMING
* ROG STRIX B550-I GAMING
* ROG STRIX B550-E GAMING
Co-developed-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Signed-off-by: Eugene Shalygin <eugene.shalygin@gmail.com>
Co-developed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Denis Pauk <pauk.denis@gmail.com>
Tested-by: Tor Vic <torvic9@mailbox.org>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The INA238 is a I2C power monitor similar to other INA2xx devices,
providing shunt voltage, bus voltage, current, power and temperature
measurements.
Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
Link: https://lore.kernel.org/r/20211102052754.817220-3-nathan@nathanrossi.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Pull driver core updates from Greg KH:
"Here is the big set of driver core changes for 5.16-rc1.
All of these have been in linux-next for a while now with no reported
problems.
Included in here are:
- big update and cleanup of the sysfs abi documentation files and
scripts from Mauro. We are almost at the place where we can
properly check that the running kernel's sysfs abi is documented
fully.
- firmware loader updates
- dyndbg updates
- kernfs cleanups and fixes from Christoph
- device property updates
- component fix
- other minor driver core cleanups and fixes"
* tag 'driver-core-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (122 commits)
device property: Drop redundant NULL checks
x86/build: Tuck away built-in firmware under FW_LOADER
vmlinux.lds.h: wrap built-in firmware support under FW_LOADER
firmware_loader: move struct builtin_fw to the only place used
x86/microcode: Use the firmware_loader built-in API
firmware_loader: remove old DECLARE_BUILTIN_FIRMWARE()
firmware_loader: formalize built-in firmware API
component: do not leave master devres group open after bind
dyndbg: refine verbosity 1-4 summary-detail
gpiolib: acpi: Replace custom code with device_match_acpi_handle()
i2c: acpi: Replace custom function with device_match_acpi_handle()
driver core: Provide device_match_acpi_handle() helper
dyndbg: fix spurious vNpr_info change
dyndbg: no vpr-info on empty queries
dyndbg: vpr-info on remove-module complete, not starting
device property: Add missed header in fwnode.h
Documentation: dyndbg: Improve cli param examples
dyndbg: Remove support for ddebug_query param
dyndbg: make dyndbg a known cli param
dyndbg: show module in vpr-info in dd-exec-queries
...
|
|
TMP461 is almost identical to TMP451, which is already supported by the
lm90 driver. At the same time, unlike other sensors from the TMP401
compatible series, it only supports 8-bit temperature read operations,
and it supports negative temperatures when configured for its default
temperature range, and it supports a temperature offset register.
Supporting this chip in the tmp401 driver adds unnecessary complexity.
Remove its support from this driver and support the chip with the lm90
driver instead.
Fixes: 24333ac26d01 ("hwmon: (tmp401) use smb word operations instead of 2 smb byte operations")
Reported-by: David T. Wilson <david.wilson@nasa.gov>
Cc: David T. Wilson <david.wilson@nasa.gov>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
TMP461 is almost identical to TMP451 and was actually detected as TMP451
with the existing lm90 driver if its I2C address is 0x4c. Add support
for it to the lm90 driver. At the same time, improve the chip detection
function to at least try to distinguish between TMP451 and TMP461.
As a side effect, this fixes commit 24333ac26d01 ("hwmon: (tmp401) use
smb word operations instead of 2 smb byte operations"). TMP461 does not
support word operations on temperature registers, which causes bad
temperature readings with the tmp401 driver. The lm90 driver does not
perform word operations on temperature registers and thus does not have
this problem.
Support is listed as basic because TMP461 supports a sensor resolution
of 0.0625 degrees C, while the lm90 driver assumes a resolution of 0.125
degrees C. Also, the TMP461 supports negative temperatures with its
default temperature range, which is not the case for similar chips
supported by the lm90 and the tmp401 drivers. Those limitations will be
addressed with follow-up patches.
Fixes: 24333ac26d01 ("hwmon: (tmp401) use smb word operations instead of 2 smb byte operations")
Reported-by: David T. Wilson <david.wilson@nasa.gov>
Cc: David T. Wilson <david.wilson@nasa.gov>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The nominal speed of each fan can be obtained with
i8k_get_fan_nominal_speed(), however the result is not available
from userspace.
Change that by adding fanX_min, fanX_max and fanX_target attributes.
All are RO since fan control happens over pwm.
Tested on a Dell Inspiron 3505 and a Dell Latitude C600.
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20210926221044.14327-2-W_Armin@gmx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Sysfs interface of the tmp421 driver was extended in the recent patches
so lets update the documentation to reflect that.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Link: https://lore.kernel.org/r/6ae22fdf18513ddd09f430ef9c5e46c17e27886b.1634206677.git.krzysztof.adamski@nokia.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The appropriate mantissa values for the lm25066 family's direct-format
current and power readings are a function of the sense resistor
employed between the SENSE and VIN pins of the chip. Instead of
assuming that resistance is always the same 1mOhm as used in the
datasheet, allow it to be configured via a device-tree property
("shunt-resistor-micro-ohms").
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Link: https://lore.kernel.org/r/20210928092242.30036-8-zev@bewilderbeest.net
[groeck: Fixed checkpatch warnings]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add hardware monitoring driver for Maxim MAX6620 Fan controller
Originally-from: L. Grunenberg <contact@lgrunenberg.de>
Originally-from: Cumulus Networks <support@cumulusnetworks.com>
Originally-from: Shuotian Cheng <shuche@microsoft.com>
Signed-off-by: Arun Saravanan Balachandran <Arun_Saravanan_Balac@dell.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Move the ABI attributes documentation from:
Documentation/hwmon/sysfs-interface.rst
in order for it to follow the usual ABI documentation. That
allows script/get_abi.pl to properly handle it.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/5f47619ed882b0b8d1c84b56f7ea17bac0854b77.1632994837.git.mchehab+huawei@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit id "b00647c46c9d7f6ee1ff6aaf335906101755e614",
adds reporting current and voltage to k10temp.c
The commit id "0a4e668b5d52eed8026f5d717196b02b55fb2dc6",
removed reporting current and voltage from k10temp.c
The curr and in(voltage) entries are not removed from
"k10temp_info" structure. Removing those residue entries.
while at it, update k10temp driver documentation
Signed-off-by: suma hegde <suma.hegde@amd.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210902174155.7365-2-nchatrad@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This driver exposes hardware sensors of the Aquacomputer D5 Next
watercooling pump, which communicates through a proprietary USB HID
protocol.
Available sensors are pump and fan speed, power, voltage and current, as
well as coolant temperature. Also available through debugfs are the serial
number, firmware version and power-on count.
Attaching a fan is optional and allows it to be controlled using
temperature curves directly from the pump. If it's not connected,
the fan-related sensors will report zeroes.
The pump can be configured either through software or via its physical
interface. Configuring the pump through this driver is not implemented,
as it seems to require sending it a complete configuration. That
includes addressable RGB LEDs, for which there is no standard sysfs
interface. Thus, that task is better suited for userspace tools.
This driver has been tested on x86_64, both in-kernel and as a module.
Signed-off-by: Aleksa Savic <savicaleksa83@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
- Add documentation for SB-RMI module
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Akshay Gupta <Akshay.Gupta@amd.com>
Signed-off-by: Naveen Krishna Chatradhi <nchatrad@amd.com>
Link: https://lore.kernel.org/r/20210726133615.9709-2-nchatrad@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Changeset 1496be719468 ("dt-bindings: firmware: arm,scpi: Convert to json schema")
renamed: Documentation/devicetree/bindings/arm/arm,scpi.txt
to: Documentation/devicetree/bindings/firmware/arm,scpi.yaml.
Update its cross-reference accordingly.
Fixes: 1496be719468 ("dt-bindings: firmware: arm,scpi: Convert to json schema")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://lore.kernel.org/r/b5a2b0cb83e7f8193b4be4cef9250dd4c42877ab.1626947923.git.mchehab+huawei@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Make top and bottom border lines match.
Documentation/hwmon/sht4x.rst:42: WARNING: Malformed table.
Text in column margin in table line 4.
Fixes: 505c2549373f ("hwmon: Add sht4x Temperature and Humidity Sensor Driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Navin Sankar Velliangiri <navin@linumiz.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: linux-hwmon@vger.kernel.org
Link: https://lore.kernel.org/r/20210727232054.7426-1-rdunlap@infradead.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This adds support for the Delta DPS-920AB PSU.
Only missing feature is fan control which the PSU supports.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Link: https://lore.kernel.org/r/20210607103431.2039073-1-robert.marko@sartura.hr
[groeck: Add MODULE_IMPORT_NS(PMBUS);]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add documentation and index link for pim4328 PMBus driver.
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The :doc:`foo` tag is auto-generated via automarkup.py.
So, use the filename at the sources, instead of :doc:`foo`.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/32b0db7e79a3ed0e817213113c607a1b819e3867.1622898327.git.mchehab+huawei@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
pwmX_enable supports three possible values:
0: Fan control disabled. Duty cycle is fixed to 0%
1: Fan control enabled, pwm mode. Duty cycle is determined by
values written into Target Duty Cycle registers.
2: Fan control enabled, rpm mode
Duty cycle is adjusted such that fan speed matches
the values in Target Count registers
The current code does not do this; instead, it mixes pwm control
configuration with fan speed monitoring configuration. Worse, it
reports that pwm control would be disabled (pwmX_enable==0) when
it is in fact enabled in pwm mode. Part of the problem may be that
the chip sets the "TACH input enable" bit on its own whenever the
mode bit is set to RPM mode, but that doesn't mean that "TACH input
enable" accurately reflects the pwm mode.
Fix it up and only handle pwm control with the pwmX_enable attributes.
In the documentation, clarify that disabling pwm control (pwmX_enable=0)
sets the pwm duty cycle to 0%. In the code, explain why TACH_INPUT_EN
is set together with RPM_MODE.
While at it, only update the configuration register if the configuration
has changed, and only update the cached configuration if updating the
chip configuration was successful.
Cc: Jan Kundrát <jan.kundrat@cesnet.cz>
Cc: Václav Kubernát <kubernat@cesnet.cz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Václav Kubernát <kubernat@cesnet.cz>
Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Link: https://lore.kernel.org/r/20210526154022.3223012-4-linux@roeck-us.net
|
|
The MAX31790 has two sets of registers for pwm duty cycles, one to request
a duty cycle and one to read the actual current duty cycle. Both do not
have to be the same.
When reporting the pwm duty cycle to the user, the actual pwm duty cycle
from pwm duty cycle registers needs to be reported. When setting it, the
pwm target duty cycle needs to be written. Since we don't know the actual
pwm duty cycle after a target pwm duty cycle has been written, set the
valid flag to false to indicate that actual pwm duty cycle should be read
from the chip instead of using cached values.
Cc: Jan Kundrát <jan.kundrat@cesnet.cz>
Cc: Václav Kubernát <kubernat@cesnet.cz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Václav Kubernát <kubernat@ceesnet.cz>
Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Link: https://lore.kernel.org/r/20210526154022.3223012-3-linux@roeck-us.net
|
|
This patch adds a hwmon driver for the SHT4x Temperature and
Humidity sensor.
Signed-off-by: Navin Sankar Velliangiri <navin@linumiz.com>
[groeck: dropped unnecessary empty line and continuation lines]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The entry for mp2888 is missing and it causes the following
'make htmldocs' build warning:
Documentation/hwmon/mp2888.rst: WARNING: document isn't included in any toctree
Add the mp2888 entry.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210521172218.37592-1-festevam@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for mp2888 device from Monolithic Power Systems, Inc. (MPS)
vendor. This is a digital, multi-phase, pulse-width modulation
controller.
This device supports:
- One power rail.
- Programmable Multi-Phase up to 10 Phases.
- PWM-VID Interface
- One pages 0 for telemetry.
- Programmable pins for PMBus Address.
- Built-In EEPROM to Store Custom Configurations.
- Can configured VOUT readout in direct or VID format and allows
setting of different formats on rails 1 and 2. For VID the following
protocols are available: VR13 mode with 5-mV DAC; VR13 mode with
10-mV DAC, IMVP9 mode with 5-mV DAC.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20210511055619.118104-3-vadimp@nvidia.com
[groeck: Add MODULE_IMPORT_NS]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add support for Flex BMR310, BMR456, BMR457, BMR458, BMR480, BMR490,
BMR491 and BMR492 to the pmbus driver
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Link: https://lore.kernel.org/r/20210507194023.61138-4-erik.rosen@metormote.com
[groeck: Fixed minor whitespace error]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add documentation for the new pmbus flags PMBUS_WRITE_PROTECTED,
PMBUS_NO_CAPABILITY and PMBUS_READ_STATUS_AFTER_FAILED_CHECK
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Link: https://lore.kernel.org/r/20210507194023.61138-3-erik.rosen@metormote.com
[groeck: Added newline at end of file]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
While UTF-8 characters can be used at the Linux documentation,
the best is to use them only when ASCII doesn't offer a good replacement.
So, replace the occurences of the following UTF-8 characters:
- U+2010 ('‐'): HYPHEN
- U+2013 ('–'): EN DASH
- U+2019 ('’'): RIGHT SINGLE QUOTATION MARK
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/ccdd1bf45963a7748188a97c75f667b37bd43d2f.1620641727.git.mchehab+huawei@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The conversion tools used during DocBook/LaTeX/html/Markdown->ReST
conversion and some cut-and-pasted text contain some characters that
aren't easily reachable on standard keyboards and/or could cause
troubles when parsed by the documentation build system.
Replace the occurences of the following characters:
- U+2010 ('‐'): HYPHEN
as ASCII HYPHEN is preferred over U+2010
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/ba8b5122ac9d4918fd966d0eb0a5ca9d89044b04.1621159997.git.mchehab+huawei@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
TI TMP1075 is a LM75 compatible sensor, so lets
add support for it.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Link: https://lore.kernel.org/r/20210429121150.106804-1-robert.marko@sartura.hr
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Update documentation for zl6100 driver and fix dead links to technical
specifications
Signed-off-by: Erik Rosen <erik.rosen@metormote.com>
Link: https://lore.kernel.org/r/20210423153329.33457-3-erik.rosen@metormote.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
While UTF-8 characters can be used at the Linux documentation,
the best is to use them only when ASCII doesn't offer a good replacement.
So, replace the occurences of the following UTF-8 characters:
- U+2013 ('–'): EN DASH
In this specific case, EN DASH was used instead of a minus
sign. So, replace it by a single hyphen.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/73b3c7c1eef5c12ddc941624d23689313bd56529.1620744606.git.mchehab+huawei@kernel.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
Commit 60268b0e8258 ("hwmon: (amd_energy) modify the visibility of
the counters") restricted visibility of AMD energy counters to work
around a side-channel attack using energy data to determine which
instructions are executed. The attack is described in 'PLATYPUS:
Software-based Power Side-Channel Attacks on x86'. It relies on quick
and accurate energy readings.
This change made the counters provided by the amd_energy driver
effectively unusable for non-provileged users. However, unprivileged
read access is the whole point of hardware monitoring attributes.
An attempt to remedy the situation by limiting and randomizing access
to chip registers was rejected by AMD. Since the driver is for all
practical purposes unusable, remove it.
Cc: Naveen Krishna Chatradhi <nchatrad@amd.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Hardware monitoring sysfs attributes are used and displayed by unrestricted
userspace applications. Standard attributes therefore have to be world
readable, since otherwise those userspace applications would either have
to run as super-user or display an error. None of those makes sense.
Clarify the expected scope of attribute access in the ABI document.
Cc: Naveen Krishna Chatradhi <nchatrad@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
Guenter Roeck
Marcello Sylvester Bauer
Aleksa Savic
Armin Wolf
Christian Lamparter
Eugene Shalygin
Paul Cercueil
Jae Hyun Yoo
Alistair Francis
Patrick Rudolph
Aleksandr Mezin
Howard.Chiu@quantatw.com
Denis Pauk
Nathan Rossi
Linus Torvalds
Krzysztof Adamski
Zev Weiss
Arun Saravanan Balachandran
Mauro Carvalho Chehab
suma hegde
Akshay Gupta
Randy Dunlap
Robert Marko
Erik Rosen
Navin Sankar Velliangiri
Fabio Estevam
Vadim Pasternak