aboutsummaryrefslogtreecommitdiffstats
path: root/Documentation/netlabel (unfollow)
AgeCommit message (Collapse)AuthorFilesLines
2018-10-10s390/pkey: Introduce new API for random protected key verificationIngo Franzki3-1/+83
Introduce a new ioctl API and in-kernel API to verify if a random protected key is still valid. A protected key is invalid when its wrapping key verification pattern does not match the verification pattern of the LPAR. Each time an LPAR is activated, a new LPAR wrapping key is generated and the wrapping key verification pattern is updated. Both APIs are described in detail in the header files arch/s390/include/asm/pkey.h and arch/s390/include/uapi/asm/pkey.h. Signed-off-by: Ingo Franzki <ifranzki@linux.ibm.com> Reviewed-by: Harald Freudenberger <freude@linux.ibm.com> Reviewed-by: Hendrik Brueckner <brueckner@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-10s390/pkey: Add sysfs attributes to emit secure key blobsIngo Franzki1-0/+104
Add binary read-only sysfs attributes for the pkey module that can be used to read random ccadata secure keys from. Keys are read from these attributes using a cat-like interface. A typical use case for those keys is to encrypt a swap device using the paes cipher. During processing of /etc/crypttab, the random random ccadata secure key to encrypt the swap device is read from one of the attributes. The following attributes are added: ccadata/aes_128 ccadata/aes_192 ccadata/aes_256 ccadata/aes_128_xts ccadata/aes_256_xts Each attribute emits a secure key blob for the corresponding key size and cipher mode. Signed-off-by: Ingo Franzki <ifranzki@linux.ibm.com> Reviewed-by: Harald Freudenberger <freude@linux.ibm.com> Reviewed-by: Hendrik Brueckner <brueckner@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-10s390/pkey: Add sysfs attributes to emit protected key blobsIngo Franzki1-0/+127
Add binary read-only sysfs attributes for the pkey module that can be used to read random protected keys from. Keys are read from these attributes using a cat-like interface. A typical use case for those keys is to encrypt a swap device using the paes cipher. During processing of /etc/crypttab, the random protected key to encrypt the swap device is read from one of the attributes. The following attributes are added: protkey/aes_128 protkey/aes_192 protkey/aes_256 protkey/aes_128_xts protkey/aes_256_xts Each attribute emits a protected key blob for the corresponding key size and cipher mode. Signed-off-by: Ingo Franzki <ifranzki@linux.ibm.com> Reviewed-by: Harald Freudenberger <freude@linux.ibm.com> Reviewed-by: Hendrik Brueckner <brueckner@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390/pkey: Define protected key blob formatIngo Franzki1-6/+27
Define a new protected key blob format. Protected key blobs use a type of 0x00, to be distinguished from other CCA key blobs. CCA defines type 0x00 as NULL key blob, but pkey will never use NULL keys anyway, so it is save to reuse this type. Using another so far undefined type value would introduce the risk that sometimes in the future CCA defines this so far unassigned type for a future key blob. Also add defines for the key token types and versions, and use them instead of hard coded hex values. Signed-off-by: Ingo Franzki <ifranzki@linux.ibm.com> Reviewed-by: Harald Freudenberger <freude@linux.ibm.com> Reviewed-by: Hendrik Brueckner <brueckner@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390/pkey: Introduce new API for random protected key generationIngo Franzki3-0/+73
This patch introduces a new ioctl API and in-kernel API to generate a random protected key. The protected key is generated in a way that the effective clear key is never exposed in clear. Both APIs are described in detail in the header files arch/s390/include/asm/pkey.h and arch/s390/include/uapi/asm/pkey.h. Signed-off-by: Ingo Franzki <ifranzki@linux.ibm.com> Reviewed-by: Harald Freudenberger <freude@linux.ibm.com> Reviewed-by: Hendrik Brueckner <brueckner@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390/zcrypt: add ap_adapter_mask sysfs attributeHarald Freudenberger1-0/+16
This patch provides a new sysfs attribute file /sys/bus/ap/ap_adapter_mask. This read-only attribute refrects the apm field as it is found in the PQAP(QCI) crypto info. Signed-off-by: Harald Freudenberger <freude@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390/zcrypt: provide apfs failure code on type 86 error replyHarald Freudenberger2-1/+25
The apfs field (AP final status) is set on transport protocol failures (reply code 0x90) for type 86 replies. For CCA cprbs this value is copied into the xcrb status field which gives userspace a hint for the failure reason. However, for EP11 cprbs there is no such status field in the xcrb struct. So now regardless of the request type, if a reply type 86 with transport protocol failure is seen, the apfs value is printed as part of the debug message. So the user has a chance to see the apfs value without using a special build kernel. Signed-off-by: Harald Freudenberger <freude@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390/zcrypt: zcrypt device driver cleanupHarald Freudenberger17-191/+117
Some cleanup in the s390 zcrypt device driver: - Removed fragments of pcixx crypto card code. This code can't be reached anymore because the hardware detection function does not recognize crypto cards < CEX2 since commit f56545430736 ("s390/zcrypt: Introduce QACT support for AP bus devices.") - Rename of some files and driver names which where still reflecting pcixx support to cex2a/cex2c. - Removed all the zcrypt version strings in the file headers. There is only one place left - the zcrypt.h header file is now the only place for zcrypt device driver version info. - Zcrypt version pump up from 2.2.0 to 2.2.1. Signed-off-by: Harald Freudenberger <freude@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390/kasan: add support for mem= kernel parameterVasily Gorbik1-0/+3
Handle mem= kernel parameter in kasan to limit physical memory. Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390/kasan: optimize kasan vmemmap allocationVasily Gorbik1-1/+2
Kasan implementation now supports memory hotplug operations. For that reason regions of initially standby memory are now skipped from shadow mapping and are mapped/unmapped dynamically upon bringing memory online/offline. Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390/kasan: avoid kasan crash with standby memory definedVasily Gorbik1-1/+18
Kasan early memory allocator simply chops off memory blocks from the end of the physical memory. Reuse mem_detect info to identify actual online memory end rather than using max_physmem_end. This allows to run the kernel with kasan enabled and standby memory defined. Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390/head: avoid doubling early boot stack size under KASANVasily Gorbik2-1/+2
Early boot stack uses predefined 4 pages of memory 0x8000-0xC000. This stack is used to run not instumented decompressor/facilities verification C code. It doesn't make sense to double its size when the kernel is built with KASAN support. BOOT_STACK_ORDER is introduced to avoid that. Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390/mm: improve debugfs ptdump markers walkingVasily Gorbik1-1/+1
This allows to print multiple markers when they happened to have the same value. ... 0x001bfffff0100000-0x001c000000000000 255M PMD I ---[ Kasan Shadow End ]--- ---[ vmemmap Area ]--- 0x001c000000000000-0x001c000002000000 32M PMD RW X ... Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390/mm: optimize debugfs ptdump kasan zero page walkingVasily Gorbik1-1/+34
Kasan zero p4d/pud/pmd/pte are always filled in with corresponding kasan zero entries. Walking kasan zero page backed area is time consuming and unnecessary. When kasan zero p4d/pud/pmd is encountered, it eventually points to the kasan zero page always with the same attributes and nothing but it, therefore zero p4d/pud/pmd could be jumped over. Also adds a space between address range and pages number to separate them from each other when pages number is huge. 0x0018000000000000-0x0018000010000000 256M PMD RW X 0x0018000010000000-0x001bfffff0000000 1073741312M PTE RO X 0x001bfffff0000000-0x001bfffff0001000 4K PTE RW X Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390/kasan: add option for 4-level paging supportVasily Gorbik5-7/+35
By default 3-level paging is used when the kernel is compiled with kasan support. Add 4-level paging option to support systems with more then 3TB of physical memory and to cover 4-level paging specific code with kasan as well. Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390/kasan: free early identity mapping structuresVasily Gorbik3-2/+13
Kasan initialization code is changed to populate persistent shadow first, save allocator position into pgalloc_freeable and proceed with early identity mapping creation. This way early identity mapping paging structures could be freed at once after switching to swapper_pg_dir when early identity mapping is not needed anymore. Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390/kasan: enable stack and global variables access checksVasily Gorbik2-1/+6
By defining KASAN_SHADOW_OFFSET in Kconfig stack and global variables memory access check instrumentation is enabled. gcc version 4.9.2 or newer is also required. Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390/dumpstack: disable __dump_trace kasan instrumentationVasily Gorbik1-1/+1
Walking async_stack produces false positives. Disable __dump_trace function instrumentation for now. Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390/kasan: reipl and kexec supportVasily Gorbik4-3/+8
Some functions from both arch/s390/kernel/ipl.c and arch/s390/kernel/machine_kexec.c are called without DAT enabled (or with and without DAT enabled code paths). There is no easy way to partially disable kasan for those files without a substantial rework. Disable kasan for both files for now. To avoid disabling kasan for arch/s390/kernel/diag.c DAT flag is enabled in diag308 call. pcpu_delegate which disables DAT is marked with __no_sanitize_address to disable instrumentation for that one function. Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390/smp: kasan stack instrumentation supportVasily Gorbik2-4/+4
smp_start_secondary function is called without DAT enabled. To avoid disabling kasan instrumentation for entire arch/s390/kernel/smp.c smp_start_secondary has been split in 2 parts. smp_start_secondary has instrumentation disabled, it does minimal setup and enables DAT. Then instrumentated __smp_start_secondary is called to do the rest. __load_psw_mask function instrumentation has been disabled as well to be able to call it from smp_start_secondary. Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09compiler: introduce __no_sanitize_address_or_inlineVasily Gorbik1-0/+7
Due to conflict between kasan instrumentation and inlining https://gcc.gnu.org/bugzilla/show_bug.cgi?id=67368 functions which are defined as inline could not be called from functions defined with __no_sanitize_address. Introduce __no_sanitize_address_or_inline which would expand to __no_sanitize_address when the kernel is built with kasan support and to inline otherwise. This helps to avoid disabling kasan instrumentation for entire files. Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390/kasan: use noexec and large pagesVasily Gorbik6-5/+118
To lower memory footprint and speed up kasan initialisation detect EDAT availability and use large pages if possible. As we know how much memory is needed for initialisation, another simplistic large page allocator is introduced to avoid memory fragmentation. Since facilities list is retrieved anyhow, detect noexec support and adjust pages attributes. Handle noexec kernel option to avoid inconsistent kasan shadow memory pages flags. Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390/kasan: dynamic shadow mem allocation for modulesVasily Gorbik2-12/+14
Move from modules area entire shadow memory preallocation to dynamic allocation per module load. This behaivior has been introduced for x86 with bebf56a1b: "This patch also forces module_alloc() to return 8*PAGE_SIZE aligned address making shadow memory handling ( kasan_module_alloc()/kasan_module_free() ) more simple. Such alignment guarantees that each shadow page backing modules address space correspond to only one module_alloc() allocation" Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390/mm: add kasan shadow to the debugfs pgtable dumpVasily Gorbik1-6/+15
This change adds address space markers for kasan shadow memory. Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390/kasan: avoid user access code instrumentationVasily Gorbik1-0/+4
Kasan instrumentation adds "store" check for variables marked as modified by inline assembly. With user pointers containing addresses from another address space this produces false positives. static inline unsigned long clear_user_xc(void __user *to, ...) { asm volatile( ... : "+a" (to) ... User space access functions are wrapped by manually instrumented functions in kasan common code, which should be sufficient to catch errors. So, we just disable uaccess.o instrumentation altogether. Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390/kasan: double the stack sizeVasily Gorbik2-1/+5
Kasan stack instrumentation pads stack variables with redzones, which increases stack frames size significantly. Stack sizes are increased from 16k to 32k in the code, as well as for the kernel stack overflow detection option (CHECK_STACK). Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390/kasan: add initialization code and enable itVasily Gorbik8-7/+343
Kasan needs 1/8 of kernel virtual address space to be reserved as the shadow area. And eventually it requires the shadow memory offset to be known at compile time (passed to the compiler when full instrumentation is enabled). Any value picked as the shadow area offset for 3-level paging would eat up identity mapping on 4-level paging (with 1PB shadow area size). So, the kernel sticks to 3-level paging when kasan is enabled. 3TB border is picked as the shadow offset. The memory layout is adjusted so, that physical memory border does not exceed KASAN_SHADOW_START and vmemmap does not go below KASAN_SHADOW_END. Due to the fact that on s390 paging is set up very late and to cover more code with kasan instrumentation, temporary identity mapping and final shadow memory are set up early. The shadow memory mapping is later carried over to init_mm.pgd during paging_init. For the needs of paging structures allocation and shadow memory population a primitive allocator is used, which simply chops off memory blocks from the end of the physical memory. Kasan currenty doesn't track vmemmap and vmalloc areas. Current memory layout (for 3-level paging, 2GB physical memory). ---[ Identity Mapping ]--- 0x0000000000000000-0x0000000000100000 ---[ Kernel Image Start ]--- 0x0000000000100000-0x0000000002b00000 ---[ Kernel Image End ]--- 0x0000000002b00000-0x0000000080000000 2G <- physical memory border 0x0000000080000000-0x0000030000000000 3070G PUD I ---[ Kasan Shadow Start ]--- 0x0000030000000000-0x0000030010000000 256M PMD RW X <- shadow for 2G memory 0x0000030010000000-0x0000037ff0000000 523776M PTE RO NX <- kasan zero ro page 0x0000037ff0000000-0x0000038000000000 256M PMD RW X <- shadow for 2G modules ---[ Kasan Shadow End ]--- 0x0000038000000000-0x000003d100000000 324G PUD I ---[ vmemmap Area ]--- 0x000003d100000000-0x000003e080000000 ---[ vmalloc Area ]--- 0x000003e080000000-0x000003ff80000000 ---[ Modules Area ]--- 0x000003ff80000000-0x0000040000000000 2G Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390: add pgd_page primitiveVasily Gorbik1-1/+10
Add pgd_page primitive which is required by kasan common code. Also fixes typo in p4d_page definition. Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390: introduce MAX_PTRS_PER_P4DVasily Gorbik1-0/+2
Kasan common code requires MAX_PTRS_PER_P4D definition, which in case of s390 is always PTRS_PER_P4D. Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390/kasan: replace some memory functionsVasily Gorbik2-3/+30
Follow the common kasan approach: "KASan replaces memory functions with manually instrumented variants. Original functions declared as weak symbols so strong definitions in mm/kasan/kasan.c could replace them. Original functions have aliases with '__' prefix in name, so we could call non-instrumented variant if needed." Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390/kasan: avoid instrumentation of early C codeVasily Gorbik4-0/+5
Instrumented C code cannot run without the kasan shadow area. Exempt source code files from kasan which are running before / used during kasan initialization. Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390/kasan: avoid vdso instrumentationVasily Gorbik2-2/+4
vdso is mapped into user space processes, which won't have kasan shodow mapped. Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390/mm: add missing pfn_to_kaddr helperVasily Gorbik1-0/+1
kasan common code uses pfn_to_kaddr, which is defined by many other architectures. Adding it as well to avoid a build error. Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390: move ipl block and cmd line handling to early boot phaseVasily Gorbik15-176/+355
To distinguish zfcpdump case and to be able to parse some of the kernel command line arguments early (e.g. mem=) ipl block retrieval and command line construction code is moved to the early boot phase. "memory_end" is set up correctly respecting "mem=" and hsa_size in case of the zfcpdump. arch/s390/boot/string.c is introduced to provide string handling and command line parsing functions to early boot phase code for the compressed kernel image case. Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390/sclp: introduce sclp_early_get_hsa_sizeVasily Gorbik2-0/+12
Introduce sclp_early_get_hsa_size function to be used during early memory detection. This function allows to find a memory limit imposed during zfcpdump. Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com> Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390/mem_detect: add info source debug printVasily Gorbik1-0/+17
Print mem_detect info source when memblock=debug is specified. Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390/mem_detect: replace tprot loop with binary searchVasily Gorbik4-36/+20
In a situation when other memory detection methods are not available (no SCLP and no z/VM diag260), continuous online memory is assumed. Replacing tprot loop with faster binary search, as only online memory end has to be found. Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com> Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390/mem_detect: use SCLP info for continuous memory detectionVasily Gorbik2-2/+8
When neither SCLP storage info, nor z/VM diag260 "storage configuration" are available assume a continuous online memory of size specified by SCLP info. Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com> Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390/mem_detect: introduce z/VM specific diag260 callVasily Gorbik2-0/+53
In the case when z/VM memory is defined with "define storage config" command, SCLP storage info is not available. Utilize diag260 "storage configuration" call, to get information about z/VM specific guest memory definitions with potential memory holes. Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390/mem_detect: introduce SCLP storage infoVasily Gorbik6-10/+74
SCLP storage info allows to detect continuous and non-continuous online memory under LPAR, z/VM and KVM, when standby memory is defined. Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com> Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390: introduce .boot.data section compile time validationVasily Gorbik2-2/+19
Make sure that .boot.data sections of vmlinux and arch/s390/compressed/vmlinux match before producing the compressed kernel image. Symbols presence, order and sizes are cross-checked. Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390/mem_detect: move tprot loop to early boot phaseVasily Gorbik11-69/+277
Move memory detection to early boot phase. To store online memory regions "struct mem_detect_info" has been introduced together with for_each_mem_detect_block iterator. mem_detect_info is later converted to memblock. Also introduces sclp_early_get_meminfo function to get maximum physical memory and maximum increment number. Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com> Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390/sclp: move sclp_early_read_info to sclp_early_core.cVasily Gorbik5-64/+81
To enable early online memory detection sclp_early_read_info has been moved to sclp_early_core.c. sclp_info_sccb has been made a part of .boot.data, which allows to reuse it later during early kernel startup and make sclp_early_read_info call just once. Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com> Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390: introduce .boot.data sectionVasily Gorbik6-4/+56
Introduce .boot.data section which is "shared" between the decompressor code and the decompressed kernel. The decompressor will store values in it, and copy over to the decompressed image before starting it. This method allows to avoid using pre-defined addresses and other hacks to pass values between those boot phases. .boot.data section is a part of init data, and will be freed after kernel initialization is complete. For uncompressed kernel image, .boot.data section is basically the same as .init.data Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390/decompressor: clean up and rename compressed/misc.cVasily Gorbik4-24/+14
Since compressed/misc.c is conditionally compiled move error reporting code to boot/main.c. With that being done compressed/misc.c has no "miscellaneous" functions left and is all about plain decompression now. Rename it accordingly. Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390: rescue initrd as early as possibleVasily Gorbik5-38/+40
To avoid multi-stage initrd rescue operation and to simplify assumptions during early memory allocations move initrd at some final safe destination as early as possible. This would also allow us to drop .bss usage restrictions for some files. Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390/sclp: simplify early hsa_size detectionVasily Gorbik1-57/+3
Architecture documentation suggests that hsa_size has been available in the read info since the list-directed ipl dump has been introduced. By using this value few early sclp calls could be avoided. Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com> Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390/decompressor: get rid of .bss usageVasily Gorbik2-13/+6
Using .bss in early code should be avoided. It might overlay initrd image or not yet be initialized. Clean up the last couple of places in the decompressor's code where .bss is used and enfore no .bss usage check on boot/compressed/misc.c. In particular: - initializing free_mem_ptr and free_mem_end_ptr with values guarantee that these variables won't end up in the .bss section. - define STATIC_RW_DATA to go into .data section. Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390/decompressor: rework uncompressed image info collectionVasily Gorbik7-56/+61
The kernel decompressor has to know several bits of information about uncompressed image. Currently this info is collected by running "nm" on uncompressed vmlinux + "sed" and producing sizes.h file. This method worked well, but it has several disadvantages. Obscure symbols name pattern matching is fragile. Adding new values makes pattern even longer. Logic is spread across code and make file. Limited ability to adjust symbols values (currently magic lma value of 0x100000 is always subtracted). Apart from that same pieces of information (and more) would be needed for early memory detection and features like KASLR outside of boot/compressed/ folder where sizes.h is generated. To overcome limitations new "struct vmlinux_info" has been introduced to include values needed for the decompressor and the rest of the boot code. The only static instance of vmlinux_info is produced during vmlinux link step by filling in struct fields by the linker (like it is done with input_data in boot/compressed/vmlinux.scr.lds.S). This way individual values could be adjusted with all the knowledge linker has and arithmetic it supports. Later .vmlinux.info section (which contains struct vmlinux_info) is transplanted into the decompressor image and dropped from uncompressed image altogether. While doing that replace "compressed/vmlinux.scr.lds.S" linker script (whose purpose is to rename .data section in piggy.o to .rodata.compressed) with plain objcopy command. And simplify decompressor's linker script. Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2018-10-09s390: remove decompressor's head.SVasily Gorbik8-64/+43
Decompressor's head.S provided "data mover" sole purpose of which has been to safely move uncompressed kernel at 0x100000 and jump to it. With current bzImage layout entire decompressor's code guaranteed to be in a safe location under 0x100000, and hence could not be overwritten during kernel move. For that reason head.S could be replaced with simple memmove function. To do so introduce early boot code phase which is executed from arch/s390/boot/head.S after "verify_facilities" and takes care of optional kernel image decompression and transition to it. Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.