| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
QSGMII is a SerDes protocol clocked at 5 Gbaud (4 times higher than
SGMII which is clocked at 1.25 Gbaud), with the same 8b/10b encoding and
some extra symbols for synchronization. Logically it offers 4 SGMII
interfaces multiplexed onto the same physical lanes. Each MAC PCS has
its own in-band AN process with the system side of the QSGMII PHY, which
is identical to the regular SGMII AN process.
So allow QSGMII as a valid in-band AN mode, since it is no different
from software perspective from regular SGMII.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Typically a MAC PCS auto-configures itself after it receives the
negotiated copper-side link settings from the PHY, but some MAC devices
are more special and need manual interpretation of the SGMII AN result.
In other cases, the PCS exposes the entire tx_config_reg base page as it
is transmitted on the wire during auto-negotiation, so it makes sense to
be able to decode the equivalent lp_advertised bit mask from the raw u16
(of course, "lp" considering the PCS to be the local PHY).
Therefore, add the bit definitions for the SGMII registers 4 and 5
(local device ability, link partner ability), as well as a link_mode
conversion helper that can be used to feed the AN results into
phy_resolve_aneg_linkmode.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a cosmetic patch that makes the dp, tx_vid, queue_mapping and
pcp local variable definitions a bit closer in length, so they don't
look like an eyesore as much.
The 'ds' variable is not used otherwise, except for ds->dp.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are 3 things that are wrong with the DSA deferred xmit mechanism:
1. Its introduction has made the DSA hotpath ever so slightly more
inefficient for everybody, since DSA_SKB_CB(skb)->deferred_xmit needs
to be initialized to false for every transmitted frame, in order to
figure out whether the driver requested deferral or not (a very rare
occasion, rare even for the only driver that does use this mechanism:
sja1105). That was necessary to avoid kfree_skb from freeing the skb.
2. Because L2 PTP is a link-local protocol like STP, it requires
management routes and deferred xmit with this switch. But as opposed
to STP, the deferred work mechanism needs to schedule the packet
rather quickly for the TX timstamp to be collected in time and sent
to user space. But there is no provision for controlling the
scheduling priority of this deferred xmit workqueue. Too bad this is
a rather specific requirement for a feature that nobody else uses
(more below).
3. Perhaps most importantly, it makes the DSA core adhere a bit too
much to the NXP company-wide policy "Innovate Where It Doesn't
Matter". The sja1105 is probably the only DSA switch that requires
some frames sent from the CPU to be routed to the slave port via an
out-of-band configuration (register write) rather than in-band (DSA
tag). And there are indeed very good reasons to not want to do that:
if that out-of-band register is at the other end of a slow bus such
as SPI, then you limit that Ethernet flow's throughput to effectively
the throughput of the SPI bus. So hardware vendors should definitely
not be encouraged to design this way. We do _not_ want more
widespread use of this mechanism.
Luckily we have a solution for each of the 3 issues:
For 1, we can just remove that variable in the skb->cb and counteract
the effect of kfree_skb with skb_get, much to the same effect. The
advantage, of course, being that anybody who doesn't use deferred xmit
doesn't need to do any extra operation in the hotpath.
For 2, we can create a kernel thread for each port's deferred xmit work.
If the user switch ports are named swp0, swp1, swp2, the kernel threads
will be named swp0_xmit, swp1_xmit, swp2_xmit (there appears to be a 15
character length limit on kernel thread names). With this, the user can
change the scheduling priority with chrt $(pidof swp2_xmit).
For 3, we can actually move the entire implementation to the sja1105
driver.
So this patch deletes the generic implementation from the DSA core and
adds a new one, more adequate to the requirements of PTP TX
timestamping, in sja1105_main.c.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I finally found out how the 4 management route slots are supposed to
be used, but.. it's not worth it.
The description from the comment I've just deleted in this commit is
still true: when more than 1 management slot is active at the same time,
the switch will match frames incoming [from the CPU port] on the lowest
numbered management slot that matches the frame's DMAC.
My issue was that one was not supposed to statically assign each port a
slot. Yes, there are 4 slots and also 4 non-CPU ports, but that is a
mere coincidence.
Instead, the switch can be used like this: every management frame gets a
slot at the right of the most recently assigned slot:
Send mgmt frame 1 through S0: S0 x x x
Send mgmt frame 2 through S1: S0 S1 x x
Send mgmt frame 3 through S2: S0 S1 S2 x
Send mgmt frame 4 through S3: S0 S1 S2 S3
The difference compared to the old usage is that the transmission of
frames 1-4 doesn't need to wait until the completion of the management
route. It is safe to use a slot to the right of the most recently used
one, because by protocol nobody will program a slot to your left and
"steal" your route towards the correct egress port.
So there is a potential throughput benefit here.
But mgmt frame 5 has no more free slot to use, so it has to wait until
_all_ of S0, S1, S2, S3 are full, in order to use S0 again.
And that's actually exactly the problem: I was looking for something
that would bring more predictable transmission latency, but this is
exactly the opposite: 3 out of 4 frames would be transmitted quicker,
but the 4th would draw the short straw and have a worse worst-case
latency than before.
Useless.
Things are made even worse by PTP TX timestamping, which is something I
won't go deeply into here. Suffice to say that the fact there is a
driver-level lock on the SPI bus offsets any potential throughput gains
that parallelism might bring.
So there's no going back to the multi-slot scheme, remove the
"mgmt_slot" variable from sja1105_port and the dummy static assignment
made at probe time.
While passing by, also remove the assignment to casc_port altogether.
Don't pretend that we support cascaded setups.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Switch network drivers, phy drivers, and SFP/phylink over to use the
more correct 10GBASE-R, rather than 10GBASE-KR. 10GBASE-KR is backplane
ethernet, which is 10GBASE-R with autonegotiation on top, which our
current usage on the affected platforms does not have.
The only remaining user of PHY_INTERFACE_MODE_10GKR is the Aquantia
PHY, which has a separate mode for 10GBASE-KR.
For Marvell mvpp2, we detect 10GBASE-KR, and rewrite it to 10GBASE-R
for compatibility with existing DT - this is the only network driver
at present that makes use of PHY_INTERFACE_MODE_10GKR.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recent discussion has revealed that the use of PHY_INTERFACE_MODE_10GKR
is incorrect. Add a 10GBASE-R definition, document both the -R and -KR
versions, and the fact that 10GKR was used incorrectly.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the netdev ops for managing VFs. Since most of the
management work happens in the NIC firmware, the driver becomes
mostly a pass-through for the network stack commands that want
to control and configure the VFs.
We also tweak ionic_station_set() a little to allow for
the VFs that start off with a zero'd mac address.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds new AdminQ calls and their related structs for
supporting PF controls on VFs:
CMD_OPCODE_VF_GETATTR
CMD_OPCODE_VF_SETATTR
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix up inconsistent usage of upper and lowercase letters in "Samsung"
name.
"SAMSUNG" is not an abbreviation but a regular trademarked name.
Therefore it should be written with lowercase letters starting with
capital letter.
Although advertisement materials usually use uppercase "SAMSUNG", the
lowercase version is used in all legal aspects (e.g. on Wikipedia and in
privacy/legal statements on
https://www.samsung.com/semiconductor/privacy-global/).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gpiod_get_from_of_node() is being retired in favor of
[devm_]fwnode_gpiod_get_index(), that behaves similar to
[devm_]gpiod_get_index(), but can work with arbitrary firmware node. It
will also be able to support secondary software nodes.
Let's switch this driver over.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we fail to locate GPIO for any reason other than deferral or
not-found-GPIO, we try to print device tree node info, however if might
be freed already as we called of_node_put() on it.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of fwnode_get_named_gpiod() that I plan to hide away, let's use
the new fwnode_gpiod_get_index() that mimics gpiod_get_index(), but
works with arbitrary firmware node.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no build time dependency on CONFIG_OF, but we do need to make
sure we gate the initialization of the gpio_chip::of_node member with a
proper check on CONFIG_OF_GPIO. This enables the driver to build on
platforms that do not have CONFIG_OF enabled.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Certain drivers will pass gro skbs to udp, at which point the udp driver
simply iterates through them and passes them off to encap_rcv, which is
where we pick up. At the moment, we're not attempting to coalesce these
into bundles, but we also don't want to wind up having cascaded lists of
skbs treated separately. The right behavior here, then, is to just mark
each incoming one as not on a list. This can be seen in practice, for
example, with Qualcomm's rmnet_perf driver.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Tested-by: Yaroslav Furman <yaro330@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before 8b7008620b84 ("net: Don't copy pfmemalloc flag in __copy_skb_
header()"), the pfmemalloc flag used to be between headers_start and
headers_end, which is a region we clear when preparing the packet for
encryption/decryption. This is a parameter we certainly want to
preserve, which is why 8b7008620b84 moved it out of there. The code here
was written in a world before 8b7008620b84, though, where we had to
manually account for it. This commit brings things up to speed.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Quite a bit of the test suite was designed to work with ancient kernels.
Thankfully we no longer have to deal with this. This commit updates
things that we can finally update and removes things that we can finally
remove, to avoid the build-up of the last several years as a result of
having to support ancient kernels. We can finally rely on suppress_
prefixlength being available. On the build side of things, the no-PIE
hack is no longer required, and we can bump some of the tools, repair
our m68k and i686-kvm support, and get better coverage of the static
branches used in the crypto lib and in udp_tunnel.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We want to avoid forward-declarations of function if possible.
Rearrange the igc_sw_init function implementation.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We want to avoid forward-declarations of function if possible.
Rearrange the igc_write_itr function implementation.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We want to avoid forward-declarations of function if possible.
Rearrange the igc_assign_vector function implementation.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We want to avoid forward-declarations of function if possible.
Rearrange the igc_free_q_vector function implementation.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We want to avoid forward-declarations of function if possible.
Rearrange the igc_free_q_vectors function implementation.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We want to avoid forward-declarations of function if possible.
Rearrange the igc_irq_disable function implementation.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We want to avoid forward-declarations of function if possible.
Rearrange the igc_irq_enable function implementation.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We want to avoid forward-declarations of function if possible.
Rearrange the igc_configure_msix function implementation.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We want to avoid forward-declarations of function if possible.
Rearrange the igc_set_rx_mode function implementation.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We want to avoid forward-declarations of function if possible.
Rearrange the igc_set_interrupt_capability function implementation.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We want to avoid forward-declarations of function if possible.
Rearrange the igc_alloc_mapped_page function implementation.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We want to avoid forward-declarations of function if possible.
Rearrange the igc_configure function implementation.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We want to avoid forward-declarations of function if possible.
Rearrange the igc_set_default_mac_filter function implementation.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We want to avoid forward-declarations of function if possible.
Rearrange the igc_power_down_link function implementation.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We want to avoid forward-declarations of function if possible.
Rearrange the igc_clean_tx_ring function implementation.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add support for E822 devices
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Coverity reports some of the calls to xdp_rxq_info_reg() as potential
issues, because the driver does not check its return value. However,
those calls are wrapped with "if (!xdp_rxq_info_is_reg(&ring->xdp_rxq))"
and this check alone is enough to be sure that the function will never
fail.
All possible states of xdp_rxq_info are:
- NEW,
- REGISTERED,
- UNREGISTERED,
- UNUSED.
The driver won't mark a queue as UNUSED under no circumstance, so the
return value can be ignored safely.
Add comments for Coverity right above calls to xdp_rxq_info_reg() to
suppress the warnings.
Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In ice_xsk_umem(), variable qid which is later used as an array index,
is not validated for a possible boundary exceedance. Because of that,
a calling function might receive an invalid address, which causes
general protection fault when dereferenced.
To address this, add a boundary check to see if qid is greater than the
size of a UMEM array. Also, don't let user change vsi->num_xsk_umems
just by trying to setup a second UMEM if its value is already set up
(i.e. UMEM region has already been allocated for this VSI).
While at it, make sure that ring->zca.free pointer is always zeroed out
if there is no UMEM on a specified ring.
Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In the case where the hardware gives us a null Rx descriptor, it is
theoretically possible that we could call one of our skb-construction
functions with no data pointer, which would cause a panic.
In real life, this will never happen - we only get null RX
descriptors as the final descriptor in a chain of otherwise-valid
descriptors. When this happens, the skb will be extant and we'll just
call ice_add_rx_frag(), which can deal with empty data buffers.
Unfortunately, Coverity does not have intimate knowledge of our
hardware, so we must add a check here.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Coverity reports an error that is not really an error; suppress it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Following the changes of commit 12299132b3d3 ("net: ethernet: intel: Demote
MTU change prints to debug"), change the MTU change message to netdev_dbg()
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently when there are SR-IOV VF(s) and the user does "ip link show <pf
interface>" the VF unicast MAC addresses all show 00:00:00:00:00:00
if the unicast MAC was set via VIRTCHNL (i.e. not administratively set
by the host PF).
This is misleading to the host administrator. Fix this by setting the
VF's dflt_lan_addr.addr when the VF's unicast MAC address is
configured via VIRTCHNL. There are a couple cases where we don't allow
the dflt_lan_addr.addr field to be written. First, If the VF's
pf_set_mac field is true and the VF is not trusted, then we don't allow
the dflt_lan_addr.addr to be modified. Second, if the
dflt_lan_addr.addr has already been set (i.e. via VIRTCHNL).
Also a small refactor was done to separate the flow for add and delete
MAC addresses in order to simplify the logic for error conditions
and set/clear the VF's dflt_lan_addr.addr field.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently the flow for ice_set_vf_link_state() is not configuring link
the same as all other VF link configuration flows. Fix this by only
setting the necessary VF members in ice_set_vf_link_state() and then
call ice_vc_notify_link_state() to actually configure link for the
VF. This made ice_set_pfe_link_forced() unnecessary, so it was
deleted. Also, this commonizes the link flows for the VF to all call
ice_vc_notify_link_state().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Remove Rx flex descriptor metadata and flag programming; per specification
these registers cannot be written to as they are read only.
Signed-off-by: Vignesh Sridhar <vignesh.sridhar@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Check for all unused parameters, if ethtool sent one of them,
print info about that and return error.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
After each rebuild driver deallocates q_vectors, so the interrupt
throttle rate (ITR) settings get lost.
Create a function to save and restore ITR for each queue. If a user
increases the number of queues, restore all the previous queue
settings for each existing queue, and the additional queues will
get the default setting.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When the user sets itr_setting to zero from ethtool -C, the driver changes
this value to default in ice_cfg_itr (for example after changing ring
param). Remove code that sets default value in ice_cfg_itr and move it to
place where the driver allocates q_vectors.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently we do "for (i = 0; i < pf->num_alloc_vfs; i++)" all over the
place. Many other places use macros to contain this repeated for loop,
So create the macro ice_for_each_vf(pf, i) that does the same thing.
There were a couple places we were using one loop variable and a VF
iterator, which were changed to using a local variable within the
ice_for_each_vf() macro.
Also in ice_alloc_vfs() we were setting pf->num_alloc_vfs after doing
"for (i = 0; i < num_alloc_vfs; i++)". Instead assign pf->num_alloc_vfs
right after allocating memory for the pf->vf array.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We can't have more than one default VSI so prevent another VSI from
overwriting the current dflt_vsi. This was achieved by adding the
following functions:
ice_is_dflt_vsi_in_use()
- Used to check if the default VSI is already being used.
ice_is_vsi_dflt_vsi()
- Used to check if VSI passed in is in fact the default VSI.
ice_set_dflt_vsi()
- Used to set the default VSI via a switch rule
ice_clear_dflt_vsi()
- Used to clear the default VSI via a switch rule.
Also, there was no need to introduce any locking because all mailbox
events and synchronization of switch filters for the PF happen in the
service task.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
There are many things wrong with the function
ice_set_vf_spoofchk().
1. The VSI being modified is the PF VSI, not the VF VSI.
2. We are enabling Rx VLAN pruning instead of Tx VLAN anti-spoof.
3. The spoofchk setting for each VF is not initialized correctly
or re-initialized correctly on reset.
To fix [1] we need to make sure we are modifying the VF VSI.
This is done by using the vf->lan_vsi_idx to index into the PF's
VSI array.
To fix [2] replace setting Rx VLAN pruning in ice_set_vf_spoofchk()
with setting Tx VLAN anti-spoof.
To Fix [3] we need to make sure the initial VSI settings match what
is done in ice_set_vf_spoofchk() for spoofchk=on. Also make sure
this also works for VF reset. This was done by modifying ice_vsi_init()
to account for the current spoofchk state of the VF VSI.
Because of these changes, Tx VLAN anti-spoof needs to be removed
from ice_cfg_vlan_pruning(). This is okay for the VF because this
is now controlled from the admin enabling/disabling spoofchk. For the
PF, Tx VLAN anti-spoof should not be set. This change requires us to
call ice_set_vf_spoofchk() when configuring promiscuous mode for
the VF which requires ice_set_vf_spoofchk() to move in order to prevent
a forward declaration prototype.
Also, add VLAN 0 by default when allocating a VF since the PF is unaware
if the guest OS is running the 8021q module. Without this, MDD events will
trigger on untagged traffic because spoofcheck is enabled by default. Due
to this change, ignore add/delete messages for VLAN 0 from VIRTCHNL since
this is added/deleted during VF initialization/teardown respectively and
should not be modified.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Based on the work done by Alex Duyck on other Intel drivers, add code to
support UDP segmentation offload (USO) for the ice driver.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
drivers/net/ethernet/brocade/bna/bfa_ioc.c: In function
‘bfa_ioc_fwver_clear’:
drivers/net/ethernet/brocade/bna/bfa_ioc.c:1127:13: warning: variable
‘pgoff’ set but not used [-Wunused-but-set-variable]
It is never used, and so can be removed.
Signed-off-by: yu kuai <yukuai3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current driver only exists on a non NUMA aware machine.
With 44768decb7c0 ("page_pool: handle page recycle for NUMA_NO_NODE condition")
applied we can safely change that to NUMA_NO_NODE and accommodate future
NUMA aware hardware using netsec network interface
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Vladimir Oltean
Vladimir Oltean
Russell King
Shannon Nelson
Krzysztof Kozlowski
Dmitry Torokhov
Florian Fainelli
Jason A. Donenfeld
Sasha Neftin
Jacob Keller
Krzysztof Kazimierczak
Mitch Williams
Bruce Allan
Tony Nguyen
Brett Creeley
Vignesh Sridhar
Michal Swiatkowski
yu kuai
Ilias Apalodimas