Age | Commit message (Collapse) | Author | Files | Lines |
|
On some boards we cannot detect the presence of an external Vusb, because
e.g. the 5V of the otg connector is directly connected to the 5V of the board,
and thus is always high.
This commit adds support for using such boards by only looking at the
id-detection pin.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The usb-phys on the sun8i-a33 SoC are mostly the same as sun8i-a23 but for
some reason (hw bug?) the phyctl register was moved to a different address
and is not initialized to 0 on reset.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The usb-phys on the sun8i-a23 SoC have the same setup wrt clocks as on the
sun6i-a31 SoC, but there are only 2 instead of 3 like on the sun5i-a13 SoC.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Before this commit the code for determining the disconnect threshold was
checking for "allwinner,sun4i-a10-usb-phy" or "allwinner,sun6i-a31-usb-phy"
assuming that those where the exception and then newer SoCs would use a
disconnect threshold of 2 like sun7i does. But it turns out that newer
SoCs use a disconnect threshold of 3 and sun5i and sun7i are the
exceptions, so check for those instead.
Here are the settings from the various Allwinner SDK sources:
sun4i-a10: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
sun5i-a13: USBC_Phy_Write(usbc_no, 0x2a, 2, 2);
sun6i-a31: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
sun7i-a20: USBC_Phy_Write(usbc_no, 0x2a, 2, 2);
sun8i-a23: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
sun8i-h3: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
sun9i-a80: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
Note this commit makes no functional changes as currently we only support
sun4i - sun7i.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The sunxi musb glue needs to know if a host or normal usb cable is plugged
in, add extcon support so that the musb glue can monitor the host status.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The usb0 phy is connected to an OTG controller, and as such needs some special
handling:
1) It allows explicit control over the pullups, enable these on phy_init and
disable them on phy_exit.
2) It has bits to signal id and vbus detect to the musb-core, add support for
for monitoring id and vbus detect gpio-s for use in dual role mode, and set
these bits to the correct values for operating in host only mode when no
gpios are specified in the devicetree.
While updating the devicetree binding documentation also add documentation
for the sofar undocumented usage of regulators for vbus for all 3 phys.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|