| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
In some cases, the NX hugepage mitigation for iTLB multihit is not
needed for all guests on a host. Allow disabling the mitigation on a
per-VM basis to avoid the performance hit of NX hugepages on trusted
workloads.
In order to disable NX hugepages on a VM, ensure that the userspace
actor has permission to reboot the system. Since disabling NX hugepages
would allow a guest to crash the system, it is similar to reboot
permissions.
Ideally, KVM would require userspace to prove it has access to KVM's
nx_huge_pages module param, e.g. so that userspace can opt out without
needing full reboot permissions. But getting access to the module param
file info is difficult because it is buried in layers of sysfs and module
glue. Requiring CAP_SYS_BOOT is sufficient for all known use cases.
Suggested-by: Jim Mattson <jmattson@google.com>
Reviewed-by: David Matlack <dmatlack@google.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Ben Gardon <bgardon@google.com>
Message-Id: <20220613212523.3436117-9-bgardon@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Add a quirk for KVM's behavior of emulating intercepted MONITOR/MWAIT
instructions a NOPs regardless of whether or not they are supported in
guest CPUID. KVM's current behavior was likely motiviated by a certain
fruity operating system that expects MONITOR/MWAIT to be supported
unconditionally and blindly executes MONITOR/MWAIT without first checking
CPUID. And because KVM does NOT advertise MONITOR/MWAIT to userspace,
that's effectively the default setup for any VMM that regurgitates
KVM_GET_SUPPORTED_CPUID to KVM_SET_CPUID2.
Note, this quirk interacts with KVM_X86_QUIRK_MISC_ENABLE_NO_MWAIT. The
behavior is actually desirable, as userspace VMMs that want to
unconditionally hide MONITOR/MWAIT from the guest can leave the
MISC_ENABLE quirk enabled.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220608224516.3788274-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The x86-only KVM_CAP_TRIPLE_FAULT_EVENT was (appropriately) renamed to
KVM_CAP_X86_TRIPLE_FAULT_EVENT when the patches were applied, but the
docs and selftests got left behind. Fix them.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
s390:
* add an interface to provide a hypervisor dump for secure guests
* improve selftests to show tests
x86:
* Intel IPI virtualization
* Allow getting/setting pending triple fault with KVM_GET/SET_VCPU_EVENTS
* PEBS virtualization
* Simplify PMU emulation by just using PERF_TYPE_RAW events
* More accurate event reinjection on SVM (avoid retrying instructions)
* Allow getting/setting the state of the speaker port data bit
* Rewrite gfn-pfn cache refresh
* Refuse starting the module if VM-Entry/VM-Exit controls are inconsistent
* "Notify" VM exit
|
|
Ignore 'kvm-arm.mode=protected' when using VHE so that kvm_get_mode()
only returns KVM_MODE_PROTECTED on systems where the feature is available.
Cc: David Brazdil <dbrazdil@google.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220609121223.2551-4-will@kernel.org
|
|
Currently the state of the speaker port (0x61) data bit (bit 1) is not
saved in the exported state (kvm_pit_state2) and hence is lost when
re-constructing guest state.
This patch removes the 'speaker_data_port' field from kvm_kpit_state and
instead tracks the state using a new KVM_PIT_FLAGS_SPEAKER_DATA_ON flag
defined in the API.
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Message-Id: <20220531124421.1427-1-pdurrant@amazon.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
There are cases that malicious virtual machines can cause CPU stuck (due
to event windows don't open up), e.g., infinite loop in microcode when
nested #AC (CVE-2015-5307). No event window means no event (NMI, SMI and
IRQ) can be delivered. It leads the CPU to be unavailable to host or
other VMs.
VMM can enable notify VM exit that a VM exit generated if no event
window occurs in VM non-root mode for a specified amount of time (notify
window).
Feature enabling:
- The new vmcs field SECONDARY_EXEC_NOTIFY_VM_EXITING is introduced to
enable this feature. VMM can set NOTIFY_WINDOW vmcs field to adjust
the expected notify window.
- Add a new KVM capability KVM_CAP_X86_NOTIFY_VMEXIT so that user space
can query and enable this feature in per-VM scope. The argument is a
64bit value: bits 63:32 are used for notify window, and bits 31:0 are
for flags. Current supported flags:
- KVM_X86_NOTIFY_VMEXIT_ENABLED: enable the feature with the notify
window provided.
- KVM_X86_NOTIFY_VMEXIT_USER: exit to userspace once the exits happen.
- It's safe to even set notify window to zero since an internal hardware
threshold is added to vmcs.notify_window.
VM exit handling:
- Introduce a vcpu state notify_window_exits to records the count of
notify VM exits and expose it through the debugfs.
- Notify VM exit can happen incident to delivery of a vector event.
Allow it in KVM.
- Exit to userspace unconditionally for handling when VM_CONTEXT_INVALID
bit is set.
Nested handling
- Nested notify VM exits are not supported yet. Keep the same notify
window control in vmcs02 as vmcs01, so that L1 can't escape the
restriction of notify VM exits through launching L2 VM.
Notify VM exit is defined in latest Intel Architecture Instruction Set
Extensions Programming Reference, chapter 9.2.
Co-developed-by: Xiaoyao Li <xiaoyao.li@intel.com>
Signed-off-by: Xiaoyao Li <xiaoyao.li@intel.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Co-developed-by: Chenyi Qiang <chenyi.qiang@intel.com>
Signed-off-by: Chenyi Qiang <chenyi.qiang@intel.com>
Message-Id: <20220524135624.22988-5-chenyi.qiang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
For the triple fault sythesized by KVM, e.g. the RSM path or
nested_vmx_abort(), if KVM exits to userspace before the request is
serviced, userspace could migrate the VM and lose the triple fault.
Extend KVM_{G,S}ET_VCPU_EVENTS to support pending triple fault with a
new event KVM_VCPUEVENT_VALID_FAULT_FAULT so that userspace can save and
restore the triple fault event. This extension is guarded by a new KVM
capability KVM_CAP_TRIPLE_FAULT_EVENT.
Note that in the set_vcpu_events path, userspace is able to set/clear
the triple fault request through triple_fault.pending field.
Signed-off-by: Chenyi Qiang <chenyi.qiang@intel.com>
Message-Id: <20220524135624.22988-2-chenyi.qiang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Introduce new max_vcpu_ids in KVM for x86 architecture. Userspace
can assign maximum possible vcpu id for current VM session using
KVM_CAP_MAX_VCPU_ID of KVM_ENABLE_CAP ioctl().
This is done for x86 only because the sole use case is to guide
memory allocation for PID-pointer table, a structure needed to
enable VMX IPI.
By default, max_vcpu_ids set as KVM_MAX_VCPU_IDS.
Suggested-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Zeng Guang <guang.zeng@intel.com>
Message-Id: <20220419154444.11888-1-guang.zeng@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
KVM: s390: pvdump and selftest improvements
- add an interface to provide a hypervisor dump for secure guests
- improve selftests to show tests
|
|
Pull delay-accounting update from Andrew Morton:
"A single featurette for delay accounting.
Delayed a bit because, unusually, it had dependencies on both the
mm-stable and mm-nonmm-stable queues"
* tag 'mm-nonmm-stable-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
delayacct: track delays from write-protect copy
|
|
Pull clockevent/clocksource updates from Thomas Gleixner:
- Device tree bindings for MT8186
- Tell the kernel that the RISC-V SBI timer stops in deeper power
states
- Make device tree parsing in sp804 more robust
- Dead code removal and tiny fixes here and there
- Add the missing SPDX identifiers
* tag 'timers-core-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/oxnas-rps: Fix irq_of_parse_and_map() return value
clocksource/drivers/timer-ti-dm: Remove unnecessary NULL check
clocksource/drivers/timer-sun5i: Convert to SPDX identifier
clocksource/drivers/timer-sun4i: Convert to SPDX identifier
clocksource/drivers/pistachio: Convert to SPDX identifier
clocksource/drivers/orion: Convert to SPDX identifier
clocksource/drivers/lpc32xx: Convert to SPDX identifier
clocksource/drivers/digicolor: Convert to SPDX identifier
clocksource/drivers/armada-370-xp: Convert to SPDX identifier
clocksource/drivers/mips-gic-timer: Convert to SPDX identifier
clocksource/drivers/jcore: Convert to SPDX identifier
clocksource/drivers/bcm_kona: Convert to SPDX identifier
clocksource/drivers/sp804: Avoid error on multiple instances
clocksource/drivers/riscv: Events are stopped during CPU suspend
clocksource/drivers/ixp4xx: Drop boardfile probe path
dt-bindings: timer: Add compatible for Mediatek MT8186
|
|
Pull hardware timestamping subsystem from Thierry Reding:
"This contains the new HTE (hardware timestamping engine) subsystem
that has been in the works for a couple of months now.
The infrastructure provided allows for drivers to register as hardware
timestamp providers, while consumers will be able to request events
that they are interested in (such as GPIOs and IRQs) to be timestamped
by the hardware providers.
Note that this currently supports only one provider, but there seems
to be enough interest in this functionality and we expect to see more
drivers added once this is merged"
[ Linus Walleij mentions the Intel PMC in the Elkhart and Tiger Lake
platforms as another future timestamp provider ]
* tag 'hte/for-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: timestamp: Correct id path
dt-bindings: Renamed hte directory to timestamp
hte: Uninitialized variable in hte_ts_get()
hte: Fix off by one in hte_push_ts_ns()
hte: Fix possible use-after-free in tegra_hte_test_remove()
hte: Remove unused including <linux/version.h>
MAINTAINERS: Add HTE Subsystem
hte: Add Tegra HTE test driver
tools: gpio: Add new hardware clock type
gpiolib: cdev: Add hardware timestamp clock type
gpio: tegra186: Add HTE support
gpiolib: Add HTE support
dt-bindings: Add HTE bindings
hte: Add Tegra194 HTE kernel provider
drivers: Add hardware timestamp engine (HTE) subsystem
Documentation: Add HTE subsystem guide
|
|
Pull regulator fix from Mark Brown:
"One fix that came in during the merge window, fixing an error in the
examples in the DT binding documentation for mt6315"
* tag 'regulator-fix-v5.19-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: mt6315-regulator: fix invalid allowed mode
|
|
Pull devicetree fixes from Rob Herring:
- Fixes for unevaluatedProperties warnings.
These were missed to due to a bug in dtschema which is now fixed. The
changes involve either adding missing properties or removing spurious
properties from examples.
- Update several Qualcomm binding maintainer email addresses
- Fix typo in imx8mp-media-blk-ctrl example
- Fix fixed string pattern in qcom,smd
- Correct the order of 'reg' entries in Xilinx PCI binding
* tag 'devicetree-fixes-for-5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: mtd: spi-nand: Add spi-peripheral-props.yaml reference
dt-bindings: memory-controllers: ingenic: Split out child node properties
dt-bindings: net/dsa: Add spi-peripheral-props.yaml references
dt-bindings: PCI: apple: Add missing 'power-domains' property
dt-bindings: Update Sibi Sankar's email address
dt-bindings: clock: Update my email address
dt-bindings: PCI: xilinx-cpm: Fix reg property order
dt-bindings: net: Fix unevaluatedProperties warnings in examples
dt-bindings: PCI: socionext,uniphier-pcie: Add missing child interrupt controller
dt-bindings: usb: snps,dwc3: Add missing 'dma-coherent' property
dt-bindings: soc: imx8mp-media-blk-ctrl: Fix DT example
dt-bindings: soc: qcom,smd: do not use pattern for simple rpm-requests string
|
|
Pull initial Loongarch architecture code from Arnd Bergmann:
"This is the majority of the loongarch architecture code, including the
final system call interface and all core functionality.
It still misses three sets of peripheral but vital patches to add
support for other subsystems, which have yet to pass review:
- The drivers/firmware/efi stub for booting from a standard UEFI
firmware implementation. Both the original custom boot interface
and a draft implementation of the EFI stub did not make it, so it
is currently impossible to boot the kernel, until the loongarch
specific portions get accepted into the UEFI subsystem
- The drivers/irqchip/irq-loongson-*.c drivers are shared with the
the MIPS port, but currently lack support for ACPI based booting,
which will get merged through the irqchip subsystem.
- Similarly, the drivers/pci/controller/pci-loongson.c needs to be
modified for ACPI support, which will be merged through the PCI
subsystem.
While the port cannot actually be used before all the above are
merged, having it in 5.19 helps to establish the user space ABI for
the libc ports to build on, and to help any treewide changes in the
mainline kernel get applied here as well.
A gcc-12 based tool chains for build testing is now included in
https://mirrors.edge.kernel.org/pub/tools/crosstool/"
Original description from Huacai Chen:
"LoongArch is a new RISC ISA, which is a bit like MIPS or RISC-V.
LoongArch includes a reduced 32-bit version (LA32R), a standard 32-bit
version (LA32S) and a 64-bit version (LA64). LoongArch use ACPI as its
boot protocol LoongArch-specific interrupt controllers (similar to APIC)
are already added in the next revision of ACPI Specification (current
revision is 6.4).
This patchset is adding basic LoongArch support in mainline kernel, we
can see a complete snapshot here:
https://github.com/loongson/linux/tree/loongarch-next
https://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson.git/log/?h=loongarch-next
Cross-compile tool chain to build kernel:
https://github.com/loongson/build-tools/releases/download/2021.12.21/loongarch64-clfs-2022-03-03-cross-tools-gcc-glibc.tar.xz
A CLFS-based Linux distro:
https://github.com/loongson/build-tools/releases/download/2021.12.21/loongarch64-clfs-system-2022-03-03.tar.bz2
Open-source tool chain which is under review (Binutils and Gcc are already upstream):
https://github.com/loongson/binutils-gdb/tree/upstream_v3.1
https://github.com/loongson/gcc/tree/loongarch_upstream_v6.3
https://github.com/loongson/glibc/tree/loongarch_2_35_dev_v2.2
Loongson and LoongArch documentations:
https://github.com/loongson/LoongArch-Documentation
LoongArch-specific interrupt controllers:
https://mantis.uefi.org/mantis/view.php?id=2203
https://mantis.uefi.org/mantis/view.php?id=2313"
Link: https://lore.kernel.org/lkml/20220603072053.35005-1-chenhuacai@loongson.cn/
* tag 'loongarch-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (24 commits)
MAINTAINERS: Add maintainer information for LoongArch
LoongArch: Add Loongson-3 default config file
LoongArch: Add Non-Uniform Memory Access (NUMA) support
LoongArch: Add multi-processor (SMP) support
LoongArch: Add VDSO and VSYSCALL support
LoongArch: Add some library functions
LoongArch: Add misc common routines
LoongArch: Add ELF and module support
LoongArch: Add signal handling support
LoongArch: Add system call support
LoongArch: Add memory management
LoongArch: Add process management
LoongArch: Add exception/interrupt handling
LoongArch: Add boot and setup routines
LoongArch: Add other common headers
LoongArch: Add atomic/locking headers
LoongArch: Add CPU definition headers
LoongArch: Add build infrastructure
LoongArch: Add writecombine support for drm
LoongArch: Add ELF-related definitions
...
|
|
Pull more RISC-V updates from Palmer Dabbelt:
"This is mostly some DT updates, but also a handful of cleanups and
some fixes. The most user-visible of those are:
- A device tree for the Sundance Polarberry, along with a handful of
fixes and clenups to the PolarFire SOC device trees and bindings.
- The memfd_secret syscall number is now visible to userspace,
- Some improvements to the vm layout dump, which really should have
followed shortly after the sv48 patches but I missed"
* tag 'riscv-for-linus-5.19-mw2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Move alternative length validation into subsection
riscv: mm: init: make pt_ops_set_[early|late|fixmap] static
riscv: move errata/ and kvm/ builds to arch/riscv/Kbuild
RISC-V: Mark IORESOURCE_EXCLUSIVE for reserved mem instead of IORESOURCE_BUSY
riscv: Wire up memfd_secret in UAPI header
riscv: Fix irq_work when SMP is disabled
riscv: Improve virtual kernel memory layout dump
riscv: Initialize thread pointer before calling C functions
Documentation: riscv: Add sv48 description to VM layout
RISC-V: Only default to spinwait on SBI-0.1 and M-mode
riscv: dts: icicle: sort nodes alphabetically
riscv: microchip: icicle: readability fixes
riscv: dts: microchip: add the sundance polarberry
dt-bindings: riscv: microchip: add polarberry compatible string
dt-bindings: vendor-prefixes: add Sundance DSP
riscv: dts: microchip: make the fabric dtsi board specific
dt-bindings: riscv: microchip: document icicle reference design
riscv: dts: microchip: remove soc vendor from filenames
riscv: dts: microchip: move sysctrlr out of soc bus
riscv: dts: microchip: remove icicle memory clocks
|
|
Pull driver core updates from Greg KH:
"Here is the set of driver core changes for 5.19-rc1.
Lots of tiny driver core changes and cleanups happened this cycle, but
the two major things are:
- firmware_loader reorganization and additions including the ability
to have XZ compressed firmware images and the ability for userspace
to initiate the firmware load when it needs to, instead of being
always initiated by the kernel. FPGA devices specifically want this
ability to have their firmware changed over the lifetime of the
system boot, and this allows them to work without having to come up
with yet-another-custom-uapi interface for loading firmware for
them.
- physical location support added to sysfs so that devices that know
this information, can tell userspace where they are located in a
common way. Some ACPI devices already support this today, and more
bus types should support this in the future.
Smaller changes include:
- driver_override api cleanups and fixes
- error path cleanups and fixes
- get_abi script fixes
- deferred probe timeout changes.
It's that last change that I'm the most worried about. It has been
reported to cause boot problems for a number of systems, and I have a
tested patch series that resolves this issue. But I didn't get it
merged into my tree before 5.18-final came out, so it has not gotten
any linux-next testing.
I'll send the fixup patches (there are 2) as a follow-on series to this
pull request.
All have been tested in linux-next for weeks, with no reported issues
other than the above-mentioned boot time-outs"
* tag 'driver-core-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (55 commits)
driver core: fix deadlock in __device_attach
kernfs: Separate kernfs_pr_cont_buf and rename_lock.
topology: Remove unused cpu_cluster_mask()
driver core: Extend deferred probe timeout on driver registration
MAINTAINERS: add Russ Weight as a firmware loader maintainer
driver: base: fix UAF when driver_attach failed
test_firmware: fix end of loop test in upload_read_show()
driver core: location: Add "back" as a possible output for panel
driver core: location: Free struct acpi_pld_info *pld
driver core: Add "*" wildcard support to driver_async_probe cmdline param
driver core: location: Check for allocations failure
arch_topology: Trace the update thermal pressure
kernfs: Rename kernfs_put_open_node to kernfs_unlink_open_file.
export: fix string handling of namespace in EXPORT_SYMBOL_NS
rpmsg: use local 'dev' variable
rpmsg: Fix calling device_lock() on non-initialized device
firmware_loader: describe 'module' parameter of firmware_upload_register()
firmware_loader: Move definitions from sysfs_upload.h to sysfs.h
firmware_loader: Fix configs for sysfs split
selftests: firmware: Add firmware upload selftests
...
|
|
Pull char / misc / other smaller driver subsystem updates from Greg KH:
"Here is the large set of char, misc, and other driver subsystem
updates for 5.19-rc1. The merge request for this has been delayed as I
wanted to get lots of linux-next testing due to some late arrivals of
changes for the habannalabs driver.
Highlights of this merge are:
- habanalabs driver updates for new hardware types and fixes and
other updates
- IIO driver tree merge which includes loads of new IIO drivers and
cleanups and additions
- PHY driver tree merge with new drivers and small updates to
existing ones
- interconnect driver tree merge with fixes and updates
- soundwire driver tree merge with some small fixes
- coresight driver tree merge with small fixes and updates
- mhi bus driver tree merge with lots of updates and new device
support
- firmware driver updates
- fpga driver updates
- lkdtm driver updates (with a merge conflict, more on that below)
- extcon driver tree merge with small updates
- lots of other tiny driver updates and fixes and cleanups, full
details in the shortlog.
All of these have been in linux-next for almost 2 weeks with no
reported problems"
* tag 'char-misc-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (387 commits)
habanalabs: use separate structure info for each error collect data
habanalabs: fix missing handle shift during mmap
habanalabs: remove hdev from hl_ctx_get args
habanalabs: do MMU prefetch as deferred work
habanalabs: order memory manager messages
habanalabs: return -EFAULT on copy_to_user error
habanalabs: use NULL for eventfd
habanalabs: update firmware header
habanalabs: add support for notification via eventfd
habanalabs: add topic to memory manager buffer
habanalabs: handle race in driver fini
habanalabs: add device memory scrub ability through debugfs
habanalabs: use unified memory manager for CB flow
habanalabs: unified memory manager new code for CB flow
habanalabs/gaudi: set arbitration timeout to a high value
habanalabs: add put by handle method to memory manager
habanalabs: hide memory manager page shift
habanalabs: Add separate poll interval value for protocol
habanalabs: use get_task_pid() to take PID
habanalabs: add prefetch flag to the MAP operation
...
|
|
Pull USB / Thunderbolt updates from Greg KH:
"Here is the "big" set of USB and Thunderbolt driver changes for
5.18-rc1. For the most part it's been a quiet development cycle for
the USB core, but there are the usual "hot spots" of development
activity.
Included in here are:
- Thunderbolt driver updates:
- fixes for devices without displayport adapters
- lane bonding support and improvements
- other minor changes based on device testing
- dwc3 gadget driver changes.
It seems this driver will never be finished given that the IP core
is showing up in zillions of new devices and each implementation
decides to do something different with it...
- uvc gadget driver updates as more devices start to use and rely on
this hardware as well
- usb_maxpacket() api changes to remove an unneeded and unused
parameter.
- usb-serial driver device id updates and small cleanups
- typec cleanups and fixes based on device testing
- device tree updates for usb properties
- lots of other small fixes and driver updates.
All of these have been in linux-next for weeks with no reported
problems"
* tag 'usb-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (154 commits)
USB: new quirk for Dell Gen 2 devices
usb: dwc3: core: Add error log when core soft reset failed
usb: dwc3: gadget: Move null pinter check to proper place
usb: hub: Simplify error and success path in port_over_current_notify
usb: cdns3: allocate TX FIFO size according to composite EP number
usb: dwc3: Fix ep0 handling when getting reset while doing control transfer
usb: Probe EHCI, OHCI controllers asynchronously
usb: isp1760: Fix out-of-bounds array access
xhci: Don't defer primary roothub registration if there is only one roothub
USB: serial: option: add Quectel BG95 modem
USB: serial: pl2303: fix type detection for odd device
xhci: Allow host runtime PM as default for Intel Alder Lake N xHCI
xhci: Remove quirk for over 10 year old evaluation hardware
xhci: prevent U2 link power state if Intel tier policy prevented U1
xhci: use generic command timer for stop endpoint commands.
usb: host: xhci-plat: omit shared hcd if either root hub has no ports
usb: host: xhci-plat: prepare operation w/o shared hcd
usb: host: xhci-plat: create shared hcd after having added main hcd
xhci: prepare for operation w/o shared hcd
xhci: factor out parts of xhci_gen_setup()
...
|
|
Pull tty and serial driver updates from Greg KH:
"Here is the big set of tty and serial driver updates for 5.19-rc1.
Lots of tiny cleanups in here, the major stuff is:
- termbit cleanups and unification by Ilpo. A much needed change that
goes a long way to making things simpler for all of the different
arches
- tty documentation cleanups and movements to their own place in the
documentation tree
- old tty driver cleanups and fixes from Jiri to bring some existing
drivers into the modern world
- RS485 cleanups and unifications to make it easier for individual
drivers to support this mode instead of having to duplicate logic
in each driver
- Lots of 8250 driver updates and additions
- new device id additions
- n_gsm continued fixes and cleanups
- other minor serial driver updates and cleanups
All of these have been in linux-next for weeks with no reported issues"
* tag 'tty-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (166 commits)
tty: Rework receive flow control char logic
pcmcia: synclink_cs: Don't allow CS5-6
serial: stm32-usart: Correct CSIZE, bits, and parity
serial: st-asc: Sanitize CSIZE and correct PARENB for CS7
serial: sifive: Sanitize CSIZE and c_iflag
serial: sh-sci: Don't allow CS5-6
serial: txx9: Don't allow CS5-6
serial: rda-uart: Don't allow CS5-6
serial: digicolor-usart: Don't allow CS5-6
serial: uartlite: Fix BRKINT clearing
serial: cpm_uart: Fix build error without CONFIG_SERIAL_CPM_CONSOLE
serial: core: Do stop_rx in suspend path for console if console_suspend is disabled
tty: serial: qcom-geni-serial: Remove uart frequency table. Instead, find suitable frequency with call to clk_round_rate.
dt-bindings: serial: renesas,em-uart: Add RZ/V2M clock to access the registers
serial: 8250_fintek: Check SER_RS485_RTS_* only with RS485
Revert "serial: 8250_mtk: Make sure to select the right FEATURE_SEL"
serial: msm_serial: disable interrupts in __msm_console_write()
serial: meson: acquire port->lock in startup()
serial: 8250_dw: Use dev_err_probe()
serial: 8250_dw: Use devm_add_action_or_reset()
...
|
|
SPI peripheral device bindings need to reference spi-peripheral-props.yaml
in order to use various SPI controller specific properties. Otherwise,
the unevaluatedProperties check will reject any controller specific
properties.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220525205909.2486153-1-robh@kernel.org
|
|
Binding schemas which define child node properties such as memory
controllers with timing properties need a separate schema which can be
referenced from child device schemas. This is necessary for
unevaluatedProperties checks to work properly.
Move the ingenic,nemc child properties to its own file and reference
from ingenic,nand.yaml which describes a child NAND controller.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220525210140.2489866-1-robh@kernel.org
|
|
SPI peripheral device bindings need to reference spi-peripheral-props.yaml
in order to use various SPI controller specific properties. Otherwise,
the unevaluatedProperties check will reject any controller specific
properties.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220531220122.2412711-1-robh@kernel.org
|
|
Add some basic documentation (zh_CN version) for LoongArch. LoongArch is
a new RISC ISA, which is a bit like MIPS or RISC-V. LoongArch includes a
reduced 32-bit version (LA32R), a standard 32-bit version (LA32S) and a
64-bit version (LA64).
Reviewed-by: Alex Shi <alexs@kernel.org>
Reviewed-by: Yanteng Si <siyanteng@loongson.cn>
Reviewed-by: Guo Ren <guoren@kernel.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Co-developed-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
Add some basic documentation for LoongArch. LoongArch is a new RISC ISA,
which is a bit like MIPS or RISC-V. LoongArch includes a reduced 32-bit
version (LA32R), a standard 32-bit version (LA32S) and a 64-bit version
(LA64).
Tested-by: Bagas Sanjaya <bagasdotme@gmail.com>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Co-developed-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: WANG Xuerui <git@xen0n.name>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
Pull documentation fixes from Jonathan Corbet:
"A handful of late-arriving documentation fixes and the addition of an
SVG tux logo which, I'm assured, we're going to want"
* tag 'docs-5.19-2' of git://git.lwn.net/linux:
documentation: Format button_dev as a pointer.
docs: add SVG version of the Linux logo
docs: move Linux logo into a new `images` folder
docs: blockdev: change title to match section content
docs/conf.py: Cope with removal of language=None in Sphinx 5.0.0
|
|
Pull more ARM SoC updates from Arnd Bergmann:
"This is the second part of the general SoC updates, containing
everything that did not make it in the initial pull request, or that
came in as a bugfix later.
- Devicetree updates for SoCFPGA, ASPEED, AT91 and Rockchip,
including a new machine using an ASPEED BMC.
- More DT fixes from Krzysztof Kozlowski across platforms
- A new SoC platform for the GXP baseboard management controller,
used in current server products from HPE"
* tag 'arm-late-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (56 commits)
ARM: configs: Enable more audio support for i.MX
tee: optee: Pass a pointer to virt_addr_valid()
arm64: dts: rockchip: rename Quartz64-A bluetooth gpios
arm64: dts: rockchip: add clocks property to cru node rk3368
arm64: dts: rockchip: add clocks property to cru node rk3308
arm64: dts: rockchip: add clocks to rk356x cru
ARM: dts: rockchip: add clocks property to cru node rk3228
ARM: dts: rockchip: add clocks property to cru node rk3036
ARM: dts: rockchip: add clocks property to cru node rk3066a/rk3188
ARM: dts: rockchip: add clocks property to cru node rk3288
ARM: dts: rockchip: Remove "amba" bus nodes from rv1108
ARM: dts: rockchip: add clocks property to cru node rv1108
arm64: dts: sprd: use new 'dma-channels' property
ARM: dts: da850: use new 'dma-channels' property
ARM: dts: pxa: use new 'dma-channels/requests' properties
soc: ixp4xx/qmgr: Fix unused match warning
ARM: ep93xx: Make ts72xx_register_flash() static
ARM: configs: enable support for Kontron KSwitch D10
ep93xx: clock: Do not return the address of the freed memory
arm64: dts: intel: add device tree for n6000
...
|
|
Pull more ARM multiplatform updates from Arnd Bergmann:
"The second part of the multiplatform changes now converts the
Intel/Marvell PXA platform along with the rest. The patches went
through several rebases before the merge window as bugs were found, so
they remained separate.
This has to touch a lot of drivers, in particular the touchscreen,
pcmcia, sound and clk bits, to detach the driver files from the
platform and board specific header files"
* tag 'arm-multiplatform-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (48 commits)
ARM: pxa/mmp: remove traces of plat-pxa
ARM: pxa: convert to multiplatform
ARM: pxa/sa1100: move I/O space to PCI_IOBASE
ARM: pxa: remove support for MTD_XIP
ARM: pxa: move mach/*.h to mach-pxa/
ARM: PXA: fix multi-cpu build of xsc3
ARM: pxa: move plat-pxa to drivers/soc/
ARM: mmp: rename pxa_register_device
ARM: mmp: remove tavorevb board support
ARM: pxa: remove unused mach/bitfield.h
ARM: pxa: move clk register definitions to driver
ARM: pxa: move smemc register access from clk to platform
cpufreq: pxa3: move clk register access to clk driver
ARM: pxa: remove get_clk_frequency_khz()
ARM: pxa: pcmcia: move smemc configuration back to arch
ASoC: pxa: i2s: use normal MMIO accessors
ASoC: pxa: ac97: use normal MMIO accessors
ASoC: pxa: use pdev resource for FIFO regs
Input: wm97xx - get rid of irq_enable method in wm97xx_mach_ops
Input: wm97xx - switch to using threaded IRQ
...
|
|
Pull networking fixes from Jakub Kicinski:
"Including fixes from bpf and netfilter.
Current release - new code bugs:
- af_packet: make sure to pull the MAC header, avoid skb panic in GSO
- ptp_clockmatrix: fix inverted logic in is_single_shot()
- netfilter: flowtable: fix missing FLOWI_FLAG_ANYSRC flag
- dt-bindings: net: adin: fix adi,phy-output-clock description syntax
- wifi: iwlwifi: pcie: rename CAUSE macro, avoid MIPS build warning
Previous releases - regressions:
- Revert "net: af_key: add check for pfkey_broadcast in function
pfkey_process"
- tcp: fix tcp_mtup_probe_success vs wrong snd_cwnd
- nf_tables: disallow non-stateful expression in sets earlier
- nft_limit: clone packet limits' cost value
- nf_tables: double hook unregistration in netns path
- ping6: fix ping -6 with interface name
Previous releases - always broken:
- sched: fix memory barriers to prevent skbs from getting stuck in
lockless qdiscs
- neigh: set lower cap for neigh_managed_work rearming, avoid
constantly scheduling the probe work
- bpf: fix probe read error on big endian in ___bpf_prog_run()
- amt: memory leak and error handling fixes
Misc:
- ipv6: expand & rename accept_unsolicited_na to accept_untracked_na"
* tag 'net-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (80 commits)
net/af_packet: make sure to pull mac header
net: add debug info to __skb_pull()
net: CONFIG_DEBUG_NET depends on CONFIG_NET
stmmac: intel: Add RPL-P PCI ID
net: stmmac: use dev_err_probe() for reporting mdio bus registration failure
tipc: check attribute length for bearer name
ice: fix access-beyond-end in the switch code
nfp: remove padding in nfp_nfdk_tx_desc
ax25: Fix ax25 session cleanup problems
net: usb: qmi_wwan: Add support for Cinterion MV31 with new baseline
sfc/siena: fix wrong tx channel offset with efx_separate_tx_channels
sfc/siena: fix considering that all channels have TX queues
socket: Don't use u8 type in uapi socket.h
net/sched: act_api: fix error code in tcf_ct_flow_table_fill_tuple_ipv6()
net: ping6: Fix ping -6 with interface name
macsec: fix UAF bug for real_dev
octeontx2-af: fix error code in is_valid_offset()
wifi: mac80211: fix use-after-free in chanctx code
bonding: guard ns_targets by CONFIG_IPV6
tcp: tcp_rtx_synack() can be called from process context
...
|
|
The 'unevaluatedProperties' schema checks is not fully working and doesn't
catch some cases where there's a $ref to another schema. A fix is pending,
but results in new warnings in examples.
The Apple PCIe host schema is missing 'power-domains' in the schema.
The example has 3 power domains. However, this is wrong too as actual
dts files have a single power domain and Sven confirmed 1 is correct.
Cc: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Link: https://lore.kernel.org/r/20220531215815.2408477-1-robh@kernel.org
|
|
Update email address to the quicinc.com domain.
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1654130923-18722-1-git-send-email-quic_sibis@quicinc.com
|
|
Update my email address from the defunct codeaurora.org domain to the
current quicinc.com domain.
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1654118992-4026-1-git-send-email-quic_jhugo@quicinc.com
|
|
During the repository renaming from hte to timestamp, $id path was not
updated accordingly. This patch corrects $id path.
Fixes: af583852d2ef ("dt-bindings: Renamed hte directory to timestamp")
Signed-off-by: Dipen Patel <dipenp@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
sv48 was just introduced, so add its virtual memory layout to the
documentation.
Signed-off-by: Alexandre Ghiti <alexandre.ghiti@canonical.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
Delay accounting does not track the delay of write-protect copy. When
tasks trigger many write-protect copys(include COW and unsharing of
anonymous pages[1]), it may spend a amount of time waiting for them. To
get the delay of tasks in write-protect copy, could help users to evaluate
the impact of using KSM or fork() or GUP.
Also update tools/accounting/getdelays.c:
/ # ./getdelays -dl -p 231
print delayacct stats ON
listen forever
PID 231
CPU count real total virtual total delay total delay average
6247 1859000000 2154070021 1674255063 0.268ms
IO count delay total delay average
0 0 0ms
SWAP count delay total delay average
0 0 0ms
RECLAIM count delay total delay average
0 0 0ms
THRASHING count delay total delay average
0 0 0ms
COMPACT count delay total delay average
3 72758 0ms
WPCOPY count delay total delay average
3635 271567604 0ms
[1] commit 31cc5bc4af70("mm: support GUP-triggered unsharing of anonymous pages")
Link: https://lkml.kernel.org/r/20220409014342.2505532-1-yang.yang29@zte.com.cn
Signed-off-by: Yang Yang <yang.yang29@zte.com.cn>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Jiang Xuexin <jiang.xuexin@zte.com.cn>
Reviewed-by: Ran Xiaokai <ran.xiaokai@zte.com.cn>
Reviewed-by: wangyong <wang.yong12@zte.com.cn>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Add a binding for the Sundance Polarberry board.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220509142610.128590-8-conor.dooley@microchip.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
Sundance DSP Inc. (https://www.sundancedsp.com/) is a supplier of
high-performance DSP and FPGA processor boards and I/O modules.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220509142610.128590-7-conor.dooley@microchip.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
Add a compatible for the icicle kit's reference design. This represents
the FPGA fabric's contents & is versioned to denote which release of the
reference design it applies to.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220509142610.128590-5-conor.dooley@microchip.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
Pull RTC updates from Alexandre Belloni:
"A new driver represents the bulk of the changes and then we get the
usual small fixes.
New driver:
- Renesas RZN1 rtc
Drivers:
- sun6i: Add nvmem support"
* tag 'rtc-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: mxc: Silence a clang warning
rtc: rzn1: Fix a variable type
rtc: rzn1: Fix error code in probe
rtc: rzn1: Avoid mixing variables
rtc: ftrtc010: Fix error handling in ftrtc010_rtc_probe
rtc: mt6397: check return value after calling platform_get_resource()
rtc: rzn1: fix platform_no_drv_owner.cocci warning
rtc: gamecube: Add missing iounmap in gamecube_rtc_read_offset_from_sram
rtc: meson: Fix email address in MODULE_AUTHOR
rtc: simplify the return expression of rx8025_set_offset()
rtc: pcf85063: Add a compatible entry for pca85073a
dt-binding: pcf85063: Add an entry for pca85073a
MAINTAINERS: Add myself as maintainer of the RZN1 RTC driver
rtc: rzn1: Add oscillator offset support
rtc: rzn1: Add alarm support
rtc: rzn1: Add new RTC driver
dt-bindings: rtc: rzn1: Describe the RZN1 RTC
rtc: sun6i: Add NVMEM provider
|
|
Pull i3c updates from Alexandre Belloni:
"Only clean ups and no functional change this cycle. A couple of yaml
conversions of the DT bindings, and a couple of code cleanups"
* tag 'i3c/for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
MAINTAINERS: rectify entries for some i3c drivers after dt conversion
i3c: master: svc: fix returnvar.cocci warning
i3c/master: simplify the return expression of i3c_hci_remove()
dt-bindings: i3c: Convert snps,dw-i3c-master to DT schema
dt-bindings: i3c: Convert cdns,i3c-master to DT schema
|
|
Pull watchdog updates from Wim Van Sebroeck:
- Add MediaTek MT8186 support
- Add Mediatek MT7986 reset-controller support
- Add i.MX93 support
- Add watchdog driver for Sunplus SP7021
- Add SC8180X and SC8280XP compatibles
- Add Renesas RZ/N1 Watchdog driver and support for RZ/N1
- rzg2l_wdt improvements and fixes
- Several other improvements and fixes
* tag 'linux-watchdog-5.19-rc1' of git://www.linux-watchdog.org/linux-watchdog: (38 commits)
watchdog: ts4800_wdt: Fix refcount leak in ts4800_wdt_probe
dt-bindings: watchdog: renesas,wdt: R-Car V3U is R-Car Gen4
watchdog: Add Renesas RZ/N1 Watchdog driver
dt-bindings: watchdog: renesas,wdt: Add support for RZ/N1
watchdog: wdat_wdt: Stop watchdog when uninstalling module
watchdog: wdat_wdt: Stop watchdog when rebooting the system
watchdog: wdat_wdt: Using the existing function to check parameter timeout
dt-bindings: watchdog: da9062: add watchdog timeout mode
dt-bindings: watchdog: renesas,wdt: Document RZ/G2UL SoC
watchdog: iTCO_wdt: Using existing macro define covers more scenarios
watchdog: rti-wdt: Fix pm_runtime_get_sync() error checking
dt-bindings: watchdog: Add SC8180X and SC8280XP compatibles
watchdog: rti_wdt: Fix calculation and evaluation of preset heartbeat
dt-bindings: watchdog: uniphier: Use unevaluatedProperties
watchdog: sp805: disable watchdog on remove
watchdog: da9063: optionally disable watchdog during suspend
dt-bindings: mfd: da9063: watchdog: add suspend disable option
dt-bindings: watchdog: sunxi: clarify clock support
dt-bindings: watchdog: sunxi: fix F1C100s compatible
watchdog: Add watchdog driver for Sunplus SP7021
...
|
|
Pull vfio updates from Alex Williamson:
- Improvements to mlx5 vfio-pci variant driver, including support for
parallel migration per PF (Yishai Hadas)
- Remove redundant iommu_present() check (Robin Murphy)
- Ongoing refactoring to consolidate the VFIO driver facing API to use
vfio_device (Jason Gunthorpe)
- Use drvdata to store vfio_device among all vfio-pci and variant
drivers (Jason Gunthorpe)
- Remove redundant code now that IOMMU core manages group DMA ownership
(Jason Gunthorpe)
- Remove vfio_group from external API handling struct file ownership
(Jason Gunthorpe)
- Correct typo in uapi comments (Thomas Huth)
- Fix coccicheck detected deadlock (Wan Jiabing)
- Use rwsem to remove races and simplify code around container and kvm
association to groups (Jason Gunthorpe)
- Harden access to devices in low power states and use runtime PM to
enable d3cold support for unused devices (Abhishek Sahu)
- Fix dma_owner handling of fake IOMMU groups (Jason Gunthorpe)
- Set driver_managed_dma on vfio-pci variant drivers (Jason Gunthorpe)
- Pass KVM pointer directly rather than via notifier (Matthew Rosato)
* tag 'vfio-v5.19-rc1' of https://github.com/awilliam/linux-vfio: (38 commits)
vfio: remove VFIO_GROUP_NOTIFY_SET_KVM
vfio/pci: Add driver_managed_dma to the new vfio_pci drivers
vfio: Do not manipulate iommu dma_owner for fake iommu groups
vfio/pci: Move the unused device into low power state with runtime PM
vfio/pci: Virtualize PME related registers bits and initialize to zero
vfio/pci: Change the PF power state to D0 before enabling VFs
vfio/pci: Invalidate mmaps and block the access in D3hot power state
vfio: Change struct vfio_group::container_users to a non-atomic int
vfio: Simplify the life cycle of the group FD
vfio: Fully lock struct vfio_group::container
vfio: Split up vfio_group_get_device_fd()
vfio: Change struct vfio_group::opened from an atomic to bool
vfio: Add missing locking for struct vfio_group::kvm
kvm/vfio: Fix potential deadlock problem in vfio
include/uapi/linux/vfio.h: Fix trivial typo - _IORW should be _IOWR instead
vfio/pci: Use the struct file as the handle not the vfio_group
kvm/vfio: Remove vfio_group from kvm
vfio: Change vfio_group_set_kvm() to vfio_file_set_kvm()
vfio: Change vfio_external_check_extension() to vfio_file_enforced_coherent()
vfio: Remove vfio_external_group_match_file()
...
|
|
All existing vendor DTSes are using "cpm_slcr" reg followed by "cfg" reg.
This order is also suggested by node name which is pcie@fca10000 which
suggests that cpm_slcr register should be the first.
Driver itself is using devm_platform_ioremap_resource_byname() for both
names that's why there is no functional change even on description which
are using current order.
But still prefer to change order to cover currently used description.
Fixes: e22fadb1d014 ("PCI: xilinx-cpm: Add YAML schemas for Versal CPM Root Port")
Signed-off-by: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220516102217.25960-1-bharat.kumar.gogada@xilinx.com
|
|
Pull more erofs updates from Gao Xiang:
"This is a follow-up to the main updates, including some fixes of
fscache mode related to compressed inodes and a cachefiles tracepoint.
There is also a patch to fix an unexpected decompression strategy
change due to a cleanup in the past. All the fixes are quite small.
Apart from these, documentation is also updated for a better
description of recent new features.
In addition, this has some trivial cleanups without actual code logic
changes, so I could have a more recent codebase to work on folios and
avoiding the PG_error page flag for the next cycle.
Summary:
- Leave compressed inodes unsupported in fscache mode for now
- Avoid crash when using tracepoint cachefiles_prep_read
- Fix `backmost' behavior due to a recent cleanup
- Update documentation for better description of recent new features
- Several decompression cleanups w/o logical change"
* tag 'erofs-for-5.19-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
erofs: fix 'backmost' member of z_erofs_decompress_frontend
erofs: simplify z_erofs_pcluster_readmore()
erofs: get rid of label `restart_now'
erofs: get rid of `struct z_erofs_collection'
erofs: update documentation
erofs: fix crash when enable tracepoint cachefiles_prep_read
erofs: leave compressed inodes unsupported in fscache mode for now
|
|
Pull pwm updates from Thierry Reding:
"Quite a large number of conversions this time around, courtesy of Uwe
who has been working tirelessly on these. No drivers of the legacy API
are left at this point, so as a next step the old API can be removed.
Support is added for a few new devices such as the Xilinx AXI timer-
based PWMs and the PWM IP found on Sunplus SoCs.
Other than that, there's a number of fixes, cleanups and optimizations"
* tag 'pwm/for-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (43 commits)
pwm: pwm-cros-ec: Add channel type support
dt-bindings: google,cros-ec-pwm: Add the new -type compatible
dt-bindings: Add mfd/cros_ec definitions
pwm: Document that the pinstate of a disabled PWM isn't reliable
pwm: twl-led: Implement .apply() callback
pwm: lpc18xx: Implement .apply() callback
pwm: mediatek: Implement .apply() callback
pwm: lpc32xx: Implement .apply() callback
pwm: tegra: Implement .apply() callback
pwm: stmpe: Implement .apply() callback
pwm: sti: Implement .apply() callback
pwm: pwm-mediatek: Add support for MediaTek Helio X10 MT6795
dt-bindings: pwm: pwm-mediatek: Add documentation for MT6795 SoC
pwm: tegra: Optimize period calculation
pwm: renesas-tpu: Improve precision of period and duty_cycle calculation
pwm: renesas-tpu: Improve maths to compute register settings
pwm: renesas-tpu: Rename variables to match the usual naming
pwm: renesas-tpu: Implement .apply() callback
pwm: renesas-tpu: Make use of devm functions
pwm: renesas-tpu: Make use of dev_err_probe()
...
|
|
Pull remoteproc updates from Bjorn Andersson:
"This fixes a race condition in the user space interface for starting
and stopping remote processors, it makes the ELF loader properly skip
zero memsz segments and it cleans up the debugfs tracefile code a bit
by not checking for errors.
It introduces support for controlling the audio DSP on Qualcomm
MSM8226, as well as audio and compute DSPs on Qualcomm SC8280XP.
It makes it possible to specify the firmware path for Mediatek's
remote processors, fixes a double free in the SCP driver and addresses
an issue with the SRAM initialization on MT8195.
Lastly it deprecates the custom ELF loader in the iMX remoteproc
driver, in favor of using the shared one"
* tag 'rproc-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux: (21 commits)
dt-bindings: remoteproc: mediatek: Add optional memory-region to mtk,scp
dt-bindings: remoteproc: mediatek: Make l1tcm reg exclusive to mt819x
dt-bindings: remoteproc: st,stm32-rproc: Fix phandle-array parameters description
remoteproc: imx_rproc: Support i.MX93
dt-bindings: remoteproc: imx_rproc: Support i.MX93
remoteproc: qcom: pas: Add MSM8226 ADSP support
dt-bindings: remoteproc: qcom: pas: Add MSM8226 adsp
remoteproc: mediatek: Allow reading firmware-name from DT
dt-bindings: remoteproc: mediatek: Add firmware-name property
remoteproc: qcom: pas: Add sc8280xp remoteprocs
dt-bindings: remoteproc: qcom: pas: Add sc8280xp adsp and nsp pair
dt-bindings: remoteproc: mediatek: Add interrupts property to mtk,scp
remoteproc: imx_rproc: Ignore create mem entry for resource table
remoteproc: core: Move state checking to remoteproc_core
remoteproc: core: Remove state checking before calling rproc_boot()
remoteproc: imx_dsp_rproc: Make rsc_table optional
remoteproc: imx_dsp_rproc: use common rproc_elf_load_segments
remoteproc: elf_loader: skip segment with memsz as zero
remoteproc: mtk_scp: Fix a potential double free
remoteproc: Don't bother checking the return value of debugfs_create*
...
|
|
The docs on creating an input device driver have an example in which
button_dev is a pointer to an input_dev struct. However, in two code
snippets below, button_dev is used as if it is not a pointer. Make these
occurrences of button_dev reflect that it is a pointer.
Signed-off-by: Nelson Penn <nelsonapenn@protonmail.com>
Link: https://lore.kernel.org/r/20220522194953.12097-1-nelsonapenn@protonmail.com
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
In the Rust for Linux patch series, Jonathan Corbet requested [1] that
we avoid binary assets (such as the logo), possibly by recreating
them in SVG format.
However, it turns out there is no SVG version of the Linux logo
in the kernel tree yet, only a GIF one from the pre-v2.0.0 days.
This patch fixes that by adding a SVG version of the Linux logo,
which we could then use in the Rust for Linux documentation and
other similar places.
This is a vector re-illustration by Garrett LeSage of the original
logo by Larry Ewing, plus cleanups by IFo Hancroft.
The file was imported as-is from:
https://github.com/garrett/Tux/blob/ecd40de64250ea2b24c849e901c3297ad01e54f6/tux.svg
The stated license in the repository is:
> Public domain http://creativecommons.org/publicdomain/zero/1.0/
>
> ...but, if anyone asks:
>
> Tux was originally made by Larry Ewing in the Gimp, re-illustrated
> in vector by Garrett LeSage, using Inkscape and refined and
> cleaned up by IFo Hancroft.
Here, the acknowledgement requirement has been made mandatory to
match the wording of the existing GIF logo in `COPYING-logo`.
Both Garrett LeSage and IFo Hancroft gave their permission [2,3]
to use their re-illustration with the license as given in
the `COPYING-logo` file.
Link: https://lore.kernel.org/lkml/87fspk1xoc.fsf@meer.lwn.net/ [1]
Link: https://lore.kernel.org/lkml/YgFsD7zBZyVqyF+F@battlestation/ [2]
Link: https://lore.kernel.org/lkml/CAFfNkxV=DmRJL1Oqm3w9YzBYcNLSAG3Ss8pih9ZVwh_E-Fbw+Q@mail.gmail.com/ [3]
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Link: https://lore.kernel.org/r/20220528153132.8636-2-ojeda@kernel.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
Having assets in the top-level `Documentation` directory can make
it harder to find the documents one needs, especially if we want
to add more of them later on.
Instead, create a new `images` folder inside it that is used
to hold assets such as logos.
In addition, update the reference in `scripts/spdxcheck-test.sh`.
Link: https://lore.kernel.org/lkml/8735hicoy7.fsf@meer.lwn.net/
Suggested-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Link: https://lore.kernel.org/r/20220528153132.8636-1-ojeda@kernel.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
Ben Gardon
Sean Christopherson
Paolo Bonzini
Will Deacon
Paul Durrant
Tao Xu
Chenyi Qiang
Zeng Guang
Linus Torvalds
Rob Herring
Huacai Chen
Sibi Sankar
Jeffrey Hugo
Dipen Patel
Alexandre Ghiti
Yang Yang
Conor Dooley
Bharat Kumar Gogada
Nelson Penn
Miguel Ojeda