| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Make it possible for a client to use AuriStor's service upgrade facility.
The client does this by adding an RXRPC_UPGRADE_SERVICE control message to
the first sendmsg() of a call. This takes no parameters.
When recvmsg() starts returning data from the call, the service ID field in
the returned msg_name will reflect the result of the upgrade attempt. If
the upgrade was ignored, srx_service will match what was set in the
sendmsg(); if the upgrade happened the srx_service will be altered to
indicate the service the server upgraded to.
Note that:
(1) The choice of upgrade service is up to the server
(2) Further client calls to the same server that would share a connection
are blocked if an upgrade probe is in progress.
(3) This should only be used to probe the service. Clients should then
use the returned service ID in all subsequent communications with that
server (and not set the upgrade). Note that the kernel will not
retain this information should the connection expire from its cache.
(4) If a server that supports upgrading is replaced by one that doesn't,
whilst a connection is live, and if the replacement is running, say,
OpenAFS 1.6.4 or older or an older IBM AFS, then the replacement
server will not respond to packets sent to the upgraded connection.
At this point, calls will time out and the server must be reprobed.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Implement AuriStor's service upgrade facility. There are three problems
that this is meant to deal with:
(1) Various of the standard AFS RPC calls have IPv4 addresses in their
requests and/or replies - but there's no room for including IPv6
addresses.
(2) Definition of IPv6-specific RPC operations in the standard operation
sets has not yet been achieved.
(3) One could envision the creation a new service on the same port that as
the original service. The new service could implement improved
operations - and the client could try this first, falling back to the
original service if it's not there.
Unfortunately, certain servers ignore packets addressed to a service
they don't implement and don't respond in any way - not even with an
ABORT. This means that the client must then wait for the call timeout
to occur.
What service upgrade does is to see if the connection is marked as being
'upgradeable' and if so, change the service ID in the server and thus the
request and reply formats. Note that the upgrade isn't mandatory - a
server that supports only the original call set will ignore the upgrade
request.
In the protocol, the procedure is then as follows:
(1) To request an upgrade, the first DATA packet in a new connection must
have the userStatus set to 1 (this is normally 0). The userStatus
value is normally ignored by the server.
(2) If the server doesn't support upgrading, the reply packets will
contain the same service ID as for the first request packet.
(3) If the server does support upgrading, all future reply packets on that
connection will contain the new service ID and the new service ID will
be applied to *all* further calls on that connection as well.
(4) The RPC op used to probe the upgrade must take the same request data
as the shadow call in the upgrade set (but may return a different
reply). GetCapability RPC ops were added to all standard sets for
just this purpose. Ops where the request formats differ cannot be
used for probing.
(5) The client must wait for completion of the probe before sending any
further RPC ops to the same destination. It should then use the
service ID that recvmsg() reported back in all future calls.
(6) The shadow service must have call definitions for all the operation
IDs defined by the original service.
To support service upgrading, a server should:
(1) Call bind() twice on its AF_RXRPC socket before calling listen().
Each bind() should supply a different service ID, but the transport
addresses must be the same. This allows the server to receive
requests with either service ID.
(2) Enable automatic upgrading by calling setsockopt(), specifying
RXRPC_UPGRADEABLE_SERVICE and passing in a two-member array of
unsigned shorts as the argument:
unsigned short optval[2];
This specifies a pair of service IDs. They must be different and must
match the service IDs bound to the socket. Member 0 is the service ID
to upgrade from and member 1 is the service ID to upgrade to.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Permit bind() to be called on an AF_RXRPC socket more than once (currently
maximum twice) to bind multiple listening services to it. There are some
restrictions:
(1) All bind() calls involved must have a non-zero service ID.
(2) The service IDs must all be different.
(3) The rest of the address (notably the transport part) must be the same
in all (a single UDP socket is shared).
(4) This must be done before listen() or sendmsg() is called.
This allows someone to connect to the service socket with different service
IDs and lays the foundation for service upgrading.
The service ID used by an incoming call can be extracted from the msg_name
returned by recvmsg().
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
The addition of the AVF and virtchnl code to the i40evf driver
means we should update the i40evf.txt file with the most up to date
information.
It seems this file hasn't been updated in a while, so the
changes cover a little more than just AVF, but it's all only
in the i40evf.txt.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds documentation for Device-Tree bindings for the
syscon present in allwinner devices.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds documentation for Device-Tree bindings for the
Allwinner dwmac-sun8i driver.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A sample SPI configuration for Microchip KSZ switches.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This merges the serdev binding for the QCA7000 UART driver (Ethernet over
UART) into the existing document.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds a new DT property to define the current baud rate of the
slave device.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before we can merge the QCA7000 UART binding the document needs to be
renamed.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for the QCA7000 UART binding rework the binding document.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add device tree description info for Cortina 10G phy devices.
Signed-off-by: Bogdan Purcareata <bogdan.purcareata@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Overlapping changes in drivers/net/phy/marvell.c, bug fix in 'net'
restricting a HW workaround alongside cleanups in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Fix state pruning in bpf verifier wrt. alignment, from Daniel
Borkmann.
2) Handle non-linear SKBs properly in SCTP ICMP parsing, from Davide
Caratti.
3) Fix bit field definitions for rss_hash_type of descriptors in mlx5
driver, from Jesper Brouer.
4) Defer slave->link updates until bonding is ready to do a full commit
to the new settings, from Nithin Sujir.
5) Properly reference count ipv4 FIB metrics to avoid use after free
situations, from Eric Dumazet and several others including Cong Wang
and Julian Anastasov.
6) Fix races in llc_ui_bind(), from Lin Zhang.
7) Fix regression of ESP UDP encapsulation for TCP packets, from
Steffen Klassert.
8) Fix mdio-octeon driver Kconfig deps, from Randy Dunlap.
9) Fix regression in setting DSCP on ipv6/GRE encapsulation, from Peter
Dawson.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
ipv4: add reference counting to metrics
net: ethernet: ax88796: don't call free_irq without request_irq first
ip6_tunnel, ip6_gre: fix setting of DSCP on encapsulated packets
sctp: fix ICMP processing if skb is non-linear
net: llc: add lock_sock in llc_ui_bind to avoid a race condition
bonding: Don't update slave->link until ready to commit
test_bpf: Add a couple of tests for BPF_JSGE.
bpf: add various verifier test cases
bpf: fix wrong exposure of map_flags into fdinfo for lpm
bpf: add bpf_clone_redirect to bpf_helper_changes_pkt_data
bpf: properly reset caller saved regs after helper call and ld_abs/ind
bpf: fix incorrect pruning decision when alignment must be tracked
arp: fixed -Wuninitialized compiler warning
tcp: avoid fastopen API to be used on AF_UNSPEC
net: move somaxconn init from sysctl code
net: fix potential null pointer dereference
geneve: fix fill_info when using collect_metadata
virtio-net: enable TSO/checksum offloads for Q-in-Q vlans
be2net: Fix offload features for Q-in-Q packets
vlan: Fix tcp checksum offloads in Q-in-Q vlans
...
|
|
Document the different sysfs attributes that exist for PHY devices:
attached_dev, phy_has_fixups, phy_id and phy_interface.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we link the network device to its PHY device, document this
sysfs symbolic link.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull MMC fixes from Ulf Hansson:
"This contains fixes to make the WiFi work again for the ARM64 Hikey
board.
Together with a couple of DTS updates for the Hikey board we have also
extended the mmc pwrseq_simple, to support a new power-off-delay-us DT
property, as that was required to enable a graceful power off sequence
for the WiFi chip"
* tag 'mmc-v4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
arm64: dts: hikey: Fix WiFi support
arm64: dts: hi6220: Move board data from the dwmmc nodes to hikey dts
arm64: dts: hikey: Add the SYS_5V and the VDD_3V3 regulators
arm64: dts: hi6220: Move the fixed_5v_hub regulator to the hikey dts
arm64: dts: hikey: Add clock for the pmic mfd
mfd: dts: hi655x: Add clock binding for the pmic
mmc: pwrseq_simple: Parse DTS for the power-off-delay-us property
mmc: dt: pwrseq-simple: Invent power-off-delay-us
|
|
Pull sound fixes from Takashi Iwai:
"This contains a few HD-audio device-specific quirks and an endianess
fix for USB-audio, as well as the update of quirk model list document.
All fixes are small and trivial.
The document update could have been postponed, but it's a good thing
for user and has absolutely zero risk of breakage, so included here"
* tag 'sound-4.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - apply STAC_9200_DELL_M22 quirk for Dell Latitude D430
ALSA: hda - Update the list of quirk models
ALSA: hda - Provide dual-codecs model option for a few Realtek codecs
ALSA: hda - Apply dual-codec quirk for MSI Z270-Gaming mobo
ALSA: hda - No loopback on ALC299 codec
ALSA: usb-audio: fix Amanero Combo384 quirk on big-endian hosts
|
|
Some PHY require to wait for a bit after the reset GPIO has been
toggled. This adds support for the DT property `phy-reset-post-delay`
which gives the delay in milliseconds to wait after reset.
If the DT property is not given, no delay is observed. Post reset delay
greater than 1000ms are invalid.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The hi655x PMIC provides the regulators but also a clock. The latter is
missing in the definition, so extend the documentation to include this as
well.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
[Ulf: Split patch and updated changelog]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
During power off, after the GPIO pin has been asserted, some devices like
the Wifi chip from TI, Wl18xx, needs a delay before the host continues with
clock gating and turning off regulators as to follow a graceful shutdown
sequence.
Therefore invent an optional power-off-delay-us DT binding for
mmc-pwrseq-simple, to allow us to support this constraint.
Cc: devicetree@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
|
|
Pull ACPI fixes from Rafael Wysocki:
"These revert a 4.11 change that turned out to be problematic and add a
.gitignore file.
Specifics:
- Revert a 4.11 commit related to the ACPI-based handling of laptop
lids that made changes incompatible with existing user space stacks
and broke things there (Lv Zheng).
- Add .gitignore to the ACPI tools directory (Prarit Bhargava)"
* tag 'acpi-4.12-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "ACPI / button: Remove lid_init_state=method mode"
tools/power/acpi: Add .gitignore file
|
|
* acpi-button:
Revert "ACPI / button: Remove lid_init_state=method mode"
* acpi-tools:
tools/power/acpi: Add .gitignore file
|
|
* intel_pstate:
cpufreq: intel_pstate: Document the current behavior and user interface
* pm-cpufreq:
cpufreq: dbx500: add a Kconfig symbol
* pm-cpufreq-sched:
cpufreq: schedutil: use now as reference when aggregating shared policy requests
|
|
I've forgotten to sync the documentation with the actually available
options for some time. Now all updated.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add SOF_TIMESTAMPING_OPT_TX_SWHW option to allow an outgoing packet to
be looped to the socket's error queue with a software timestamp even
when a hardware transmit timestamp is expected to be provided by the
driver.
Applications using this option will receive two separate messages from
the error queue, one with a software timestamp and the other with a
hardware timestamp. As the hardware timestamp is saved to the shared skb
info, which may happen before the first message with software timestamp
is received by the application, the hardware timestamp is copied to the
SCM_TIMESTAMPING control message only when the skb has no software
timestamp or it is an incoming packet.
While changing sw_tx_timestamp(), inline it in skb_tx_timestamp() as
there are no other users.
CC: Richard Cochran <richardcochran@gmail.com>
CC: Willem de Bruijn <willemb@google.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The scm_timestamping struct may return multiple non-zero fields, e.g.
when both software and hardware RX timestamping is enabled, or when the
SO_TIMESTAMP(NS) option is combined with SCM_TIMESTAMPING and a false
software timestamp is generated in the recvmsg() call in order to always
return a SCM_TIMESTAMP(NS) message.
CC: Richard Cochran <richardcochran@gmail.com>
CC: Willem de Bruijn <willemb@google.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add SOF_TIMESTAMPING_OPT_PKTINFO option to request a new control message
for incoming packets with hardware timestamps. It contains the index of
the real interface which received the packet and the length of the
packet at layer 2.
The index is useful with bonding, bridges and other interfaces, where
IP_PKTINFO doesn't allow applications to determine which PHC made the
timestamp. With the L2 length (and link speed) it is possible to
transpose preamble timestamps to trailer timestamps, which are used in
the NTP protocol.
While this information could be provided by two new socket options
independently from timestamping, it doesn't look like they would be very
useful. With this option any performance impact is limited to hardware
timestamping.
Use dev_get_by_napi_id() to get the device and its index. On kernels
with disabled CONFIG_NET_RX_BUSY_POLL or drivers not using NAPI, a zero
index will be returned in the control message.
CC: Richard Cochran <richardcochran@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull staging driver fixes from Greg KH:
"Here are a number of staging driver fixes for 4.12-rc2
Most of them are typec driver fixes found by reviewers and users of
the code. There are also some removals of files no longer needed in
the tree due to the ion driver rewrite in 4.12-rc1, as well as some
wifi driver fixes. And to round it out, a MAINTAINERS file update.
All have been in linux-next with no reported issues"
* tag 'staging-4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (22 commits)
MAINTAINERS: greybus-dev list is members-only
staging: fsl-dpaa2/eth: add ETHERNET dependency
staging: typec: fusb302: refactor resume retry mechanism
staging: typec: fusb302: reset i2c_busy state in error
staging: rtl8723bs: remove re-positioned call to kfree in os_dep/ioctl_cfg80211.c
staging: rtl8192e: GetTs Fix invalid TID 7 warning.
staging: rtl8192e: rtl92e_get_eeprom_size Fix read size of EPROM_CMD.
staging: rtl8192e: fix 2 byte alignment of register BSSIDR.
staging: rtl8192e: rtl92e_fill_tx_desc fix write to mapped out memory.
staging: vc04_services: Fix bulk cache maintenance
staging: ccree: remove extraneous spin_unlock_bh() in error handler
staging: typec: Fix sparse warnings about incorrect types
staging: typec: fusb302: do not free gpio from managed resource
staging: typec: tcpm: Fix Port Power Role field in PS_RDY messages
staging: typec: tcpm: Respond to Discover Identity commands
staging: typec: tcpm: Set correct flags in PD request messages
staging: typec: tcpm: Drop duplicate PD messages
staging: typec: fusb302: Fix chip->vbus_present init value
staging: typec: fusb302: Fix module autoload
staging: typec: tcpci: declare private structure as static
...
|
|
Pull USB fixes from Greg KH:
"Here are a number of small USB fixes for 4.12-rc2
Most of them come from Johan, in his valiant quest to fix up all
drivers that could be affected by "malicious" USB devices. There's
also some fixes for more "obscure" drivers to handle some of the
vmalloc stack fallout (which for USB drivers, was always the case, but
very few people actually ran those systems...)
Other than that, the normal set of xhci and gadget and musb driver
fixes as well.
All have been in linux-next with no reported issues"
* tag 'usb-4.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (42 commits)
usb: musb: tusb6010_omap: Do not reset the other direction's packet size
usb: musb: Fix trying to suspend while active for OTG configurations
usb: host: xhci-plat: propagate return value of platform_get_irq()
xhci: Fix command ring stop regression in 4.11
xhci: remove GFP_DMA flag from allocation
USB: xhci: fix lock-inversion problem
usb: host: xhci-ring: don't need to clear interrupt pending for MSI enabled hcd
usb: host: xhci-mem: allocate zeroed Scratchpad Buffer
xhci: apply PME_STUCK_QUIRK and MISSING_CAS quirk for Denverton
usb: xhci: trace URB before giving it back instead of after
USB: serial: qcserial: add more Lenovo EM74xx device IDs
USB: host: xhci: use max-port define
USB: hub: fix SS max number of ports
USB: hub: fix non-SS hub-descriptor handling
USB: hub: fix SS hub-descriptor handling
USB: usbip: fix nonconforming hub descriptor
USB: gadget: dummy_hcd: fix hub-descriptor removable fields
doc-rst: fixed kernel-doc directives in usb/typec.rst
USB: core: of: document reference taken by companion helper
USB: ehci-platform: fix companion-device leak
...
|
|
skb_csum_hwoffload_help() uses netdev features and skb->csum_not_inet to
determine if skb needs software computation of Internet Checksum or crc32c
(or nothing, if this computation can be done by the hardware). Use it in
place of skb_checksum_help() in validate_xmit_skb() to avoid corruption
of non-GSO SCTP packets having skb->ip_summed equal to CHECKSUM_PARTIAL.
While at it, remove references to skb_csum_off_chk* functions, since they
are not present anymore in Linux _ see commit cf53b1da73bd ("Revert
"net: Add driver helper functions to determine checksum offloadability"").
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ICH9 is listed as having TCO v2, and indeed the behavior in the
datasheet corresponds to v2 (for example the NO_REBOOT flag is
accessible via the 16KiB-aligned Root Complex Base Address).
However, the TCO counts twice just like in v1; the documentation
of the SECOND_TO_STS bit says: "ICH9 sets this bit to 1 to indicate
that the TIMEOUT bit had been (or is currently) set and a second
timeout occurred before the TCO_RLD register was written. If this
bit is set and the NO_REBOOT config bit is 0, then the ICH9 will
reboot the system after the second timeout. The same can be found
in the BayTrail (Atom E3800) datasheet, and even HOWTOs around
the Internet say that it will reboot after _twice_ the specified
heartbeat.
I did not find the Apollo Lake datasheet, but because v4/v5 has
a SECOND_TO_STS bit just like the previous version I'm enabling
this for Apollo Lake as well.
Cc: linux-watchdog@vger.kernel.org
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Cygnus is a small family of SoCs, of which we currently have
devicetree for BCM11360 and BCM58300. The 11360's B53 is mostly the
same as 58xx, just requiring a tiny bit of setup that was previously
missing.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Even if this file is not yet included in any toctree, it is parsed by
Sphinx since it is named '.rst'. This patch fixes the following two
ERRORs from Sphinx build:
Documentation/usb/typec.rst:116: ERROR: Error in "kernel-doc" directive:
invalid option block.
.. kernel-doc:: drivers/usb/typec/typec.c
:functions: typec_register_cable typec_unregister_cable typec_register_plug
typec_unregister_plug
Documentation/usb/typec.rst:139: ERROR: Error in "kernel-doc" directive:
invalid option block.
.. kernel-doc:: drivers/usb/typec/typec.c
:functions: typec_set_data_role typec_set_pwr_role typec_set_vconn_role
typec_set_pwr_opmode
Signed-off-by: Markus Heiser <markus.heiser@darmarit.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
After commit 9828282e33a0 ("staging: android: ion: Remove old platform
support"), the document about devicetree of ion is no need anymore, so
just remove it.
Signed-off-by: Yisheng Xie <xieyisheng1@huawei.com>
Acked-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a document describing the current behavior and user space
interface of the intel_pstate driver in the RST format and
drop the existing outdated intel_pstate.txt document.
Also update admin-guide/pm/cpufreq.rst with proper RST references
to the new intel_pstate.rst document.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit 4b4cea91691d ("mm: vmscan: fix IO/refault regression in cache
workingset transition") introduced three new entries in memory stat
file:
- workingset_refault
- workingset_activate
- workingset_nodereclaim
This commit adds a corresponding description to the cgroup v2 docs.
Link: http://lkml.kernel.org/r/1494530293-31236-1-git-send-email-guro@fb.com
Signed-off-by: Roman Gushchin <guro@fb.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Li Zefan <lizefan@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Cc: Tigran Aivazian <aivazian.tigran@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This reverts commit ecb10b694b72ca5ea51b3c90a71ff2a11963425a.
The only expected ACPI control method lid device's usage model is
1. Listen to the lid notification,
2. Evaluate _LID after being notified by BIOS,
3. Suspend the system (if users configure to do so) after seeing "close".
It's not ensured that BIOS will notify OS after boot/resume, and
it's not ensured that BIOS will always generate "open" event upon
opening the lid.
But there are 2 wrong usage models:
1. When the lid device is responsible for suspend/resume the system,
userspace requires to see "open" event to be paired with "close" after
the system is resumed, or it will suspend the system again.
2. When an external monitor connects to the laptop attached docks,
userspace requires to see "close" event after the system is resumed so
that it can determine whether the internal display should remain dark
and the external display should be lit on.
After we made default kernel behavior to be suitable for usage model 1,
users of usage model 2 start to report regressions for such behavior
change.
Reversion of button.lid_init_state=method doesn't actually reverts to old
default behavior as doing so can enter a regression loop, but facilitates
users to work the reported regressions around with
button.lid_init_state=method.
Fixes: ecb10b694b72 (ACPI / button: Remove lid_init_state=method mode)
Cc: 4.11+ <stable@vger.kernel.org> # 4.11+
Link: https://bugzilla.kernel.org/show_bug.cgi?id=195455
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1430259
Tested-by: Steffen Weber <steffen.weber@gmail.com>
Tested-by: Julian Wiedmann <julian.wiedmann@jwi.name>
Reported-by: Joachim Frieben <jfrieben@hotmail.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Pull more power-supply updates from Sebastian Reichel:
"The power-supply subsystem has a few more changes for the v4.12 merge
window:
- New battery driver for AXP20X and AXP22X PMICs
- Improve max17042_battery for usage on x86
- Misc small cleanups & fixes"
* tag 'for-v4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (34 commits)
power: supply: cpcap-charger: Keep trickle charger bits disabled
power: supply: cpcap-charger: Fix enable for 3.8V charge setting
power: supply: cpcap-charger: Fix charge voltage configuration
power: supply: cpcap-charger: Fix charger name
power: supply: twl4030-charger: make twl4030_bci_property_is_writeable static
power: supply: sbs-battery: Add alert callback
mailmap: add Sebastian Reichel
power: supply: avoid unused twl4030-madc.h
power: supply: sbs-battery: Correct supply status with current draw
power: supply: sbs-battery: Don't ignore the first external power change
power: supply: pda_power: move from timer to delayed_work
power: supply: max17042_battery: Add support for the SCOPE property
power: supply: max17042_battery: Add support for the CHARGE_NOW property
power: supply: max17042_battery: Add support for the CHARGE_FULL_DESIGN property
power: supply: max17042_battery: mAh readings depend on r_sns value
power: supply: max17042_battery: Add support for the VOLT_MIN property
power: supply: max17042_battery: Add support for the TECHNOLOGY attribute
power: supply: max17042_battery: Add external_power_changed callback
power: supply: max17042_battery: Add support for the STATUS property
power: supply: max17042_battery: Add default platform_data fallback data
...
|
|
Pull thermal management updates from Zhang Rui:
- Fix a problem where orderly_shutdown() is called for multiple times
due to multiple critical overheating events raised in a short period
by platform thermal driver. (Keerthy)
- Introduce a backup thermal shutdown mechanism, which invokes
kernel_power_off()/emergency_restart() directly, after
orderly_shutdown() being issued for certain amount of time(specified
via Kconfig). This is useful in certain conditions that userspace may
be unable to power off the system in a clean manner and leaves the
system in a critical state, like in the middle of driver probing
phase. (Keerthy)
- Introduce a new interface in thermal devfreq_cooling code so that the
driver can provide more precise data regarding actual power to the
thermal governor every time the power budget is calculated. (Lukasz
Luba)
- Introduce BCM 2835 soc thermal driver and northstar thermal driver,
within a new sub-folder. (Rafał Miłecki)
- Introduce DA9062/61 thermal driver. (Steve Twiss)
- Remove non-DT booting on TI-SoC driver. Also add support to fetching
coefficients from DT. (Keerthy)
- Refactorf RCAR Gen3 thermal driver. (Niklas Söderlund)
- Small fix on MTK and intel-soc-dts thermal driver. (Dawei Chien,
Brian Bian)
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (25 commits)
thermal: core: Add a back up thermal shutdown mechanism
thermal: core: Allow orderly_poweroff to be called only once
Thermal: Intel SoC DTS: Change interrupt request behavior
trace: thermal: add another parameter 'power' to the tracing function
thermal: devfreq_cooling: add new interface for direct power read
thermal: devfreq_cooling: refactor code and add get_voltage function
thermal: mt8173: minor mtk_thermal.c cleanups
thermal: bcm2835: move to the broadcom subdirectory
thermal: broadcom: ns: specify myself as MODULE_AUTHOR
thermal: da9062/61: Thermal junction temperature monitoring driver
Documentation: devicetree: thermal: da9062/61 TJUNC temperature binding
thermal: broadcom: add Northstar thermal driver
dt-bindings: thermal: add support for Broadcom's Northstar thermal
thermal: bcm2835: add thermal driver for bcm2835 SoC
dt-bindings: Add thermal zone to bcm2835-thermal example
thermal: rcar_gen3_thermal: add suspend and resume support
thermal: rcar_gen3_thermal: store device match data in private structure
thermal: rcar_gen3_thermal: enable hardware interrupts for trip points
thermal: rcar_gen3_thermal: record and check number of TSCs found
thermal: rcar_gen3_thermal: check that TSC exists before memory allocation
...
|
|
Pull SCSI target updates from Nicholas Bellinger:
"Things were a lot more calm than previously expected. It's primarily
fixes in various areas, with most of the new functionality centering
around TCMU backend driver work that Xiubo Li has been driving.
Here's the summary on the feature side:
- Make T10-PI verify configurable for emulated (FILEIO + RD) backends
(Dmitry Monakhov)
- Allow target-core/TCMU pass-through to use in-kernel SPC-PR logic
(Bryant Ly + MNC)
- Add TCMU support for growing ring buffer size (Xiubo Li + MNC)
- Add TCMU support for global block data pool (Xiubo Li + MNC)
and on the bug-fix side:
- Fix COMPARE_AND_WRITE non GOOD status handling for READ phase
failures (Gary Guo + nab)
- Fix iscsi-target hang with explicitly changing per NodeACL
CmdSN number depth with concurrent login driven session
reinstatement. (Gary Guo + nab)
- Fix ibmvscsis fabric driver ABORT task handling (Bryant Ly)
- Fix target-core/FILEIO zero length handling (Bart Van Assche)
Also, there was an OOPs introduced with the WRITE_VERIFY changes that
I ended up reverting at the last minute, because as not unusual Bart
and I could not agree on the fix in time for -rc1. Since it's specific
to a conformance test, it's been reverted for now.
There is a separate patch in the queue to address the underlying
control CDB write overflow regression in >= v4.3 separate from the
WRITE_VERIFY revert here, that will be pushed post -rc1"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (30 commits)
Revert "target: Fix VERIFY and WRITE VERIFY command parsing"
IB/srpt: Avoid that aborting a command triggers a kernel warning
IB/srpt: Fix abort handling
target/fileio: Fix zero-length READ and WRITE handling
ibmvscsis: Do not send aborted task response
tcmu: fix module removal due to stuck thread
target: Don't force session reset if queue_depth does not change
iscsi-target: Set session_fall_back_to_erl0 when forcing reinstatement
target: Fix compare_and_write_callback handling for non GOOD status
tcmu: Recalculate the tcmu_cmd size to save cmd area memories
tcmu: Add global data block pool support
tcmu: Add dynamic growing data area feature support
target: fixup error message in target_tg_pt_gp_tg_pt_gp_id_store()
target: fixup error message in target_tg_pt_gp_alua_access_type_store()
target/user: PGR Support
target: Add WRITE_VERIFY_16
Documentation/target: add an example script to configure an iSCSI target
target: Use kmalloc_array() in transport_kmap_data_sg()
target: Use kmalloc_array() in compare_and_write_callback()
target: Improve size determinations in two functions
...
|
|
Pull x86 fixes from Ingo Molnar:
"Misc fixes:
- two boot crash fixes
- unwinder fixes
- kexec related kernel direct mappings enhancements/fixes
- more Clang support quirks
- minor cleanups
- Documentation fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/intel_rdt: Fix a typo in Documentation
x86/build: Don't add -maccumulate-outgoing-args w/o compiler support
x86/boot/32: Fix UP boot on Quark and possibly other platforms
x86/mm/32: Set the '__vmalloc_start_set' flag in initmem_init()
x86/kexec/64: Use gbpages for identity mappings if available
x86/mm: Add support for gbpages to kernel_ident_mapping_init()
x86/boot: Declare error() as noreturn
x86/mm/kaslr: Use the _ASM_MUL macro for multiplication to work around Clang incompatibility
x86/mm: Fix boot crash caused by incorrect loop count calculation in sync_global_pgds()
x86/asm: Don't use RBP as a temporary register in csum_partial_copy_generic()
x86/microcode/AMD: Remove redundant NULL check on mc
|
|
Pull more powerpc updates from Michael Ellerman:
"The change to the Linux page table geometry was delayed for more
testing with 16G pages, and there's the new CPU features stuff which
just needed one more polish before going in. Plus a few changes from
Scott which came in a bit late. And then various fixes, mostly minor.
Summary highlights:
- rework the Linux page table geometry to lower memory usage on
64-bit Book3S (IBM chips) using the Hash MMU.
- support for a new device tree binding for discovering CPU features
on future firmwares.
- Freescale updates from Scott:
"Includes a fix for a powerpc/next mm regression on 64e, a fix for
a kernel hang on 64e when using a debugger inside a relocated
kernel, a qman fix, and misc qe improvements."
Thanks to: Christophe Leroy, Gavin Shan, Horia Geantă, LiuHailong,
Nicholas Piggin, Roy Pledge, Scott Wood, Valentin Longchamp"
* tag 'powerpc-4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64s: Support new device tree binding for discovering CPU features
powerpc: Don't print cpu_spec->cpu_name if it's NULL
of/fdt: introduce of_scan_flat_dt_subnodes and of_get_flat_dt_phandle
powerpc/64s: Fix unnecessary machine check handler relocation branch
powerpc/mm/book3s/64: Rework page table geometry for lower memory usage
powerpc: Fix distclean with Makefile.postlink
powerpc/64e: Don't place the stack beyond TASK_SIZE
powerpc/powernv: Block PCI config access on BCM5718 during EEH recovery
powerpc/8xx: Adding support of IRQ in MPC8xx GPIO
soc/fsl/qbman: Disable IRQs for deferred QBMan work
soc/fsl/qe: add EXPORT_SYMBOL for the 2 qe_tdm functions
soc/fsl/qe: only apply QE_General4 workaround on affected SoCs
soc/fsl/qe: round brg_freq to 1kHz granularity
soc/fsl/qe: get rid of immrbar_virt_to_phys()
net: ethernet: ucc_geth: fix MEM_PART_MURAM mode
powerpc/64e: Fix hang when debugging programs with relocated kernel
|
|
Pull more documentation updates from Jonathan Corbet:
"Connect the newly RST-formatted documentation to the rest; this had to
wait until the input pull was done. There's also a few small fixes
that wandered in"
* tag 'docs-4.12-2' of git://git.lwn.net/linux:
doc: replace FTP URL to kernel.org with HTTPS one
docs: update references to the device io book
Documentation: earlycon: fix Marvell Armada 3700 UART name
docs-rst: add input docs at main index and use kernel-figure
|
|
Pull more arm64 updates from Catalin Marinas:
- Silence module allocation failures when CONFIG_ARM*_MODULE_PLTS is
enabled. This requires a check for __GFP_NOWARN in alloc_vmap_area()
- Improve/sanitise user tagged pointers handling in the kernel
- Inline asm fixes/cleanups
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Silence first allocation with CONFIG_ARM64_MODULE_PLTS=y
ARM: Silence first allocation with CONFIG_ARM_MODULE_PLTS=y
mm: Silence vmap() allocation failures based on caller gfp_flags
arm64: uaccess: suppress spurious clang warning
arm64: atomic_lse: match asm register sizes
arm64: armv8_deprecated: ensure extension of addr
arm64: uaccess: ensure extension of access_ok() addr
arm64: ensure extension of smp_store_release value
arm64: xchg: hazard against entire exchange variable
arm64: documentation: document tagged pointer stack constraints
arm64: entry: improve data abort handling of tagged pointers
arm64: hw_breakpoint: fix watchpoint matching for tagged pointers
arm64: traps: fix userspace cache maintenance emulation on a tagged pointer
|
|
Pull fbdev updates from Bartlomiej Zolnierkiewicz:
"There is nothing really major here, just a couple of small bugfixes,
improvements and cleanups.
- fix handling of probing errors in omapfb (Arvind Yadav)
- remove incorrect __exit markups in few drivers (Dmitry Torokhov)
- fix boot time logo support for drivers using deferred probe
(Takeshi Kihara)
- fix DMA allocation size for ARM CLCD driver (Liam Beguin)
- add support for specifying size via xenstore in xen-frontfb
(Juergen Gross)
- support for AUS mode in imxfb driver (Martin Kaiser)
- fix buffer on stack usage in udlfb driver (Maksim Salau)
- probe failure path fixup in sm501fb driver (Alexey Khoroshilov)
- fix config dependency loop for stifb driver (Arnd Bergmann)
- misc cleanups (Joe Perches, Christophe Leroy, Karim Eshapa, Pushkar
Jambhlekar)"
* tag 'fbdev-v4.12' of git://github.com/bzolnier/linux:
fbdev: sti: don't select CONFIG_VT
drivers/video/fbdev/omap/lcd_mipid.c: Use time comparison kernel macros
sm501fb: don't return zero on failure path in sm501fb_start()
video: fbdev: udlfb: Fix buffer on stack
video: console: Remove reference to CONFIG_8xx
dt-bindings: display: imx: entry for AUS mode
video: fbdev: imxfb: support AUS mode
drivers/video/fbdev: Fixing coding guidelines in acornfb.c
xen, fbfront: add support for specifying size via xenstore
video: ARM CLCD: fix dma allocation size
drivers/video: Convert remaining uses of pr_warning to pr_warn
video/logo: tidyup fb_logo_late_init initcall timing
video: fbdev: i810: remove incorrect __exit markups
video: fbdev: pmag-aa-fb: remove incorrect __exit markups
video: fbdev: pmagb-b-fb: remove incorrect __exit markups
video: fbdev: pmag-ba-fb: remove incorrect __exit markups
omapfb: dss: Handle return errors in dss_init_ports()
|
|
Pull block fixes from Jens Axboe:
"A smaller collection of fixes that should go into -rc1. This contains:
- A fix from Christoph, fixing a regression with the WRITE_SAME and
partial completions. Caused a BUG() on ppc.
- Fixup for __blk_mq_stop_hw_queues(), it should be static. From
Colin.
- Removal of dmesg error messages on elevator switching, when invoked
from sysfs. From me.
- Fix for blk-stat, using this_cpu_ptr() in a section only protected
by rcu_read_lock(). This breaks when PREEMPT_RCU is enabled. From
me.
- Two fixes for BFQ from Paolo, one fixing a crash and one updating
the documentation.
- An error handling lightnvm memory leak, from Rakesh.
- The previous blk-mq hot unplug lock reversal depends on the CPU
hotplug rework that isn't in mainline yet. This caused a lockdep
splat when people unplugged CPUs with blk-mq devices. From Wanpeng.
- A regression fix for DIF/DIX on blk-mq. From Wen"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: handle partial completions for special payload requests
blk-mq: NVMe 512B/4K+T10 DIF/DIX format returns I/O error on dd with split op
blk-stat: don't use this_cpu_ptr() in a preemptable section
elevator: remove redundant warnings on IO scheduler switch
block, bfq: stress that low_latency must be off to get max throughput
block, bfq: use pointer entity->sched_data only if set
nvme: lightnvm: fix memory leak
blk-mq: make __blk_mq_stop_hw_queues static
lightnvm: remove unused rq parameter of nvme_nvm_rqtocmd() to kill warning
block/mq: fix potential deadlock during cpu hotplug
|
|
FTP services were shutdown some weeks ago, so the FTP URL
does not work anymore. Fix this by replacing it with
corresponding HTTPS URL.
Signed-off-by: Michael Heimpold <michael.heimpold@i2se.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
David Howells
Jesse Brandeburg
LABBE Corentin
Woojung Huh
Stefan Wahren
Bogdan Purcareata
David S. Miller
Linus Torvalds
Florian Fainelli
Quentin Schulz
Daniel Lezcano
Ulf Hansson
Rafael J. Wysocki
Takashi Iwai
Miroslav Lichvar
Davide Caratti
Paolo Bonzini
Eric Anholt
Markus Heiser
Yisheng Xie
Roman Gushchin
Andrew Morton
Lv Zheng
Michael Heimpold