| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This documentation is old. Add a short note to describe why aliases
are no long necessary, and remove the old contact/edit info.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It oopsd for me in skb_seq_read. addr2line said it was
linux-2.6/net/core/skbuff.c:2228, which is this line:
while (st->frag_idx < skb_shinfo(st->cur_skb)->nr_frags) {
I added some printks in there and it looks like we hit this:
} else if (st->root_skb == st->cur_skb &&
skb_shinfo(st->root_skb)->frag_list) {
st->cur_skb = skb_shinfo(st->root_skb)->frag_list;
st->frag_idx = 0;
goto next_skb;
}
Actually I did some testing and added a few printks and found that the
st->cur_skb->data was 0 and hence the ptr used by iscsi_tcp was null.
This caused the kernel panic.
if (abs_offset < block_limit) {
- *data = st->cur_skb->data + abs_offset;
+ *data = st->cur_skb->data + (abs_offset - st->stepped_offset);
I enabled the debug_tcp and with a few printks found that the code did
not go to the next_skb label and could find that the sequence being
followed was this -
It hit this if condition -
if (st->cur_skb->next) {
st->cur_skb = st->cur_skb->next;
st->frag_idx = 0;
goto next_skb;
And so, now the st pointer is shifted to the next skb whereas actually
it should have hit the second else if first since the data is in the
frag_list.
else if (st->root_skb == st->cur_skb &&
skb_shinfo(st->root_skb)->frag_list) {
st->cur_skb = skb_shinfo(st->root_skb)->frag_list;
goto next_skb;
}
Reversing the two conditions the attached patch fixes the issue for me
on top of Herbert's patches.
Signed-off-by: Shyam Iyer <shyam_iyer@dell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The frag_list handling was broken in skb_seq_read:
1) We didn't add the stepped offset when looking at the head
are of fragments other than the first.
2) We didn't take the stepped offset away when setting the data
pointer in the head area.
3) The frag index wasn't reset.
This patch fixes both issues.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reducing jumbo ring size below 1024 reduces throughput for old
firmwares (3.4.216 and older) running on older (NX2031) chip,
so restore it back to 1024.
This was reduced in commit 32ec803348b4d5f1353e1d7feae30880b8b3e342
("netxen: reduce memory footprint").
Raising jumbo ring size from 512 to 1024, adds ~4MB per port, but
there's still big saving because of original patch (~20MB per port).
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ath5k_config updates the software context without taking sc->lock.
Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When CONFIG_CFG80211_REG_DEBUG is enabled and an intersection
occurs we are printing the regulatory domain passed by CRDA
and indicating its the intersected regulatory domain. Lets fix
this and print the intersection as originally intended.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This fixes two issues with the sanity check loop when processing
the country IE:
1. Do not use frequency for the current subband channel check,
this was a big fat typo.
2. Apply the 5 GHz 4-channel steps when considering max channel
on each subband as was done with a recent patch.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The patch fixes memcpy to NULL address when the ucode DMA allocation failure.
This is a fix to bug
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1861
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
After reports of poor performance, a review of the latest vendor driver
(rtl8187_linux_26.1025.0328.2007) for RTL8187L devices was undertaken.
A difference was found in the code used to index the OFDM power tables. When
the Linux driver was changed, my unit works at a much greater range than
before. I think this fixes Bugzilla #12380 and has been tested by at least
two other users.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Martín Ernesto Barreyro <barreyromartin@gmail.com>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
His email address keeps bouncing, and he's not interested in mac80211
patches etc. anyway.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The kernel manages this value internally, as necessary, as
VIFs are added/removed and as multicast routers are registered
and deregistered.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch addresses the IPv6 multicast routing issues described
below. It was tested with XORP 1.4/1.5 as the IPv6 PIM-SM routing
daemon against FreeBSD peers.
net/ipv6/ip6_input.c:
- Don't try to forward link-local multicast packets.
- Don't reset skb2->dev before calling ip6_mr_input() so packets can
be identified as coming from the PIM register vif properly.
net/ipv6/ip6mr.c:
- Fix incoming PIM register messages processing:
* The IPv6 pseudo-header should be included when checksumming PIM
messages (RFC 4601 section 4.9; RFC 3973 section 4.7.1).
* Packets decapsulated from PIM register messages should have
skb->protocol ETH_P_IPV6.
- Enable/disable IPv6 multicast forwarding on the corresponding
interface when a routing daemon adds/removes a multicast virtual
interface.
- Remove incorrect skb_pull() to fix userspace signaling.
- Enable/disable global IPv6 multicast forwarding when an IPv6
multicast routing socket is opened/closed.
net/ipv6/route.c:
- Don't use strict routing logic for packets decapsulated from PIM
register messages (similar to disabling rp_filter for the IPv4
case).
Signed-off-by: Thomas Goff <thomas.goff@boeing.com>
Reviewed-by: Fred Templin <fred.l.templin@boeing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the xfrm reverse flow lookup for icmp6 so that icmp6 packets
don't get lost over ipsec tunnels. Similar patch is in RHEL5 kernel for a quite
long time and I do not see why it isn't in mainline.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit 9db66bdcc83749affe61c61eb8ff3cf08f42afec (net: convert
TCP/DCCP ehash rwlocks to spinlocks), I forgot to change one
occurrence of rwlock_t to spinlock_t
I believe sizeof(raw_spinlock_t) might be > 0 on !CONFIG_SMP if
CONFIG_DEBUG_SPINLOCK while sizeof(raw_rwlock_t) should be 0 in this
case.
Fortunatly, CONFIG_DEBUG_SPINLOCK adds fields to both spinlock_t and
rwlock_t, but at this might change in the future (being able to debug
spinlocks but not rwlocks for example), better to be safe.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A nasty bug was found where an MTU change (or anything else that caused a
reset) could race with the interrupt code. The interrupt code was entered
by a shared interrupt during the MTU change.
This change prevents the interrupt code from running while the driver is in
the middle of its reset path.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tcp_splice_data_recv has two lengths to consider: the len parameter it
gets from tcp_read_sock, which specifies the amount of data in the skb,
and rd_desc->count, which is the amount of data the splice caller still
wants. Currently it passes just the latter to skb_splice_bits, which then
splices min(rd_desc->count, skb->len - offset) bytes.
Most of the time this is fine, except when the skb contains urgent data.
In that case len goes only up to the urgent byte and is less than
skb->len - offset. By ignoring len tcp_splice_data_recv may a) splice
data tcp_read_sock told it not to, b) return to tcp_read_sock a value > len.
Now, tcp_read_sock doesn't handle used > len and leaves the socket in a
bad state (both sk_receive_queue and copied_seq are bad at that point)
resulting in duplicated data and corruption.
Fix by passing min(rd_desc->count, len) to skb_splice_bits.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Acked-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
drivers/net/r6040.c:441: warning: unused variable 'pdev'
Signed-off-by: Manish Katiyar <mkatiyar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 9088c5609584684149f3fb5b065aa7f18dcb03ff
(udp: Improve port randomization) introduced a regression for UDP bind() syscall
to null port (getting a random port) in case lot of ports are already in use.
This is because we do about 28000 scans of very long chains (220 sockets per chain),
with many spin_lock_bh()/spin_unlock_bh() calls.
Fix this using a bitmap (64 bytes for current value of UDP_HTABLE_SIZE)
so that we scan chains at most once.
Instead of 250 ms per bind() call, we get after patch a time of 2.9 ms
Based on a report from Vitaly Mayatskikh
Reported-by: Vitaly Mayatskikh <v.mayatskih@gmail.com>
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Tested-by: Vitaly Mayatskikh <v.mayatskih@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without this fix, virtio_net makes incorrect usage of scatterlists. It sets
the end of the scatterlist chain after the first element, despite the fact
that more entries come after it.
If you try to run dma_map_sg() on one of the scatterlists given to you by
add_buf(), you will get a null pointer oops.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 77ecaf2d5a8bfd548eed3f05c1c2e6573d5de4ba ("gianfar: Fix VLAN
HW feature related frame/buffer size calculation") wrongly removed
priv->vlgrp assignment, and now priv->vlgrp is always NULL.
This patch fixes the issue, plus fixes following sparse warning
introduced by the same commit:
gianfar.c:1406:13: warning: context imbalance in 'gfar_vlan_rx_register' - wrong count at exit
gfar_vlan_rx_register() checks for "if (old_grp == grp)" and tries
to return w/o dropping the lock.
According to net/8021q/vlan.c VLAN core issues rx_register() callback:
1. In register_vlan_dev() only on a newly created group;
2. In unregister_vlan_dev() only if the group becomes empty.
Thus the check in the gianfar driver isn't needed.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In previous kernels, any kernel module could get access to the
'real-device' and the VLAN-ID for a particular VLAN. In more recent
kernels, the code was restructured such that this is hard to do
without accessing private .h files for any module that cannot use
GPL-only symbols.
Attached is a patch to once again allow non-GPL modules the ability to
access the real-device and VLAN id for VLANs.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current tx_has_work waited until all packets sent by the driver
are marked as completed by the FW. This is too greedy and it causes
the bnx2x_poll to spin in vain. The driver should only check that all
packets FW already completed are freed - only in unload flow the
driver should make sure that transmit queue is empty
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o reduce rx ring size from 8192 to 4096.
o cut down old huge lro buffers.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o set netdev->vlan_features appropriately.
o fix tso descriptor initialization for vlan case.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The userspace interfaces are protected by CONFIG_* ifdefs
and that of course can't work.
Reported by Jaswinder Singh Rajput.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make NET_NS available underneath the generic Namespaces config option
since all of the other namespace options are there.
Signed-off-by: Matt Helsley <matthltc@us.ibm.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The following patch fixes a warning caused by a missing ifdef in
isdn_ppp.c. A function was defined, but never used if CONFIG_IPPP_FILTER
was not defined.
The warning was: 'get_filter' defined but not used
Patch is against 2.6.28.1
Signed-off-by: Daniele Venzano <venza@brownhat.org>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Let the kernel developers know that i2c_attach_client() and
i2c_detach_client() are deprecated and should no longer be used.
Drivers using these should be converted to the standard device
driver binding model (probe and remove methods.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ben Dooks <ben-linux@fluff.org>
|
|
Now that all EEPROM drivers live in the same place, let's harmonize
their symbol names.
Also fix eeprom's dependencies, it definitely needs sysfs, and is no
longer experimental after many years in the kernel tree.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
|
|
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Update Kconfig text to specify this driver as I2C.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
As drivers/i2c/chips is going to go away, move the driver to
drivers/misc/eeprom. Other eeprom drivers may be moved here later, too.
Update Kconfig text to specify this driver as I2C.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
My i2c quilt tree will now be hosted on kernel.org, because I can
conveniently use rsync there.
Also list the new i2c wiki.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
It always annoyed me that the netconsole documentation didn't give me the
correct command for my distro. Update it with a command line that actually
works on my Fedora install.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a hardware errata in some revisions of the 82574 that needs
to be worked around in the driver by setting a register bit at init.
If this bit is not set A0 versions of the 82574 can generate
tx hangs.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
swab.h seems to have been missed during the header merge.
Add conditionals similar to byteorder.h and remove the
now unnecessary byteorder_no/mm.h
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If userspace supplies an invalid pointer to a read() of an inotify
instance, the inotify device's event list mutex is unlocked twice.
This causes an unbalance which effectively leaves the data structure
unprotected, and we can trigger oopses by accessing the inotify
instance from different tasks concurrently.
The best fix (contributed largely by Linus) is a total rewrite
of the function in question:
On Thu, Jan 22, 2009 at 7:05 AM, Linus Torvalds wrote:
> The thing to notice is that:
>
> - locking is done in just one place, and there is no question about it
> not having an unlock.
>
> - that whole double-while(1)-loop thing is gone.
>
> - use multiple functions to make nesting and error handling sane
>
> - do error testing after doing the things you always need to do, ie do
> this:
>
> mutex_lock(..)
> ret = function_call();
> mutex_unlock(..)
>
> .. test ret here ..
>
> instead of doing conditional exits with unlocking or freeing.
>
> So if the code is written in this way, it may still be buggy, but at least
> it's not buggy because of subtle "forgot to unlock" or "forgot to free"
> issues.
>
> This _always_ unlocks if it locked, and it always frees if it got a
> non-error kevent.
Cc: John McCutchan <ttb@tentacle.dhs.org>
Cc: Robert Love <rlove@google.com>
Cc: <stable@kernel.org>
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Use '%zu' to print out a size_t variable, not '%d'. Another case of the
"let's keep at least Linus' defconfig compile warningless" rule.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Move fuse_copy_finish() to before calling fuse_notify_poll_wakeup().
This is not a big issue because fuse_notify_poll_wakeup() should be
atomic, but it's cleaner this way, and later uses of notification will
need to be able to finish the copying before performing some actions.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
|
|
If a fuse filesystem is unmounted but the device file descriptor
remains open and a new mount reuses the old device number, then the
mount fails with EEXIST and the following warning is printed in the
kernel log:
WARNING: at fs/sysfs/dir.c:462 sysfs_add_one+0x35/0x3d()
sysfs: duplicate filename '0:15' can not be created
The cause is that the bdi belonging to the fuse filesystem was
destoryed only after the device file was released. Fix this by
calling bdi_destroy() from fuse_put_super() instead.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
CC: stable@kernel.org
|
|
Clean up error handling for the whole of fuse_fill_super() function.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
|
|
Fix the leaking file reference if allocation or initialization of
fuse_conn failed.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
CC: stable@kernel.org
|
|
ff is set to NULL and then dereferenced on line 65. Compile tested only.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
CC: stable@kernel.org
|
|
The return value of xenbus_write_transaction can be uninitialised in
the success case leading to the userspace xenstore utilities failing.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Here function vmi_activate calls a init function activate_vmi , which
causes the following section mismatch warnings:
LD arch/x86/kernel/built-in.o
WARNING: arch/x86/kernel/built-in.o(.text+0x13ba9): Section mismatch
in reference from the function vmi_activate() to the function
.init.text:vmi_time_init()
The function vmi_activate() references
the function __init vmi_time_init().
This is often because vmi_activate lacks a __init
annotation or the annotation of vmi_time_init is wrong.
WARNING: arch/x86/kernel/built-in.o(.text+0x13bd1): Section mismatch
in reference from the function vmi_activate() to the function
.devinit.text:vmi_time_bsp_init()
The function vmi_activate() references
the function __devinit vmi_time_bsp_init().
This is often because vmi_activate lacks a __devinit
annotation or the annotation of vmi_time_bsp_init is wrong.
WARNING: arch/x86/kernel/built-in.o(.text+0x13bdb): Section mismatch
in reference from the function vmi_activate() to the function
.devinit.text:vmi_time_ap_init()
The function vmi_activate() references
the function __devinit vmi_time_ap_init().
This is often because vmi_activate lacks a __devinit
annotation or the annotation of vmi_time_ap_init is wrong.
Fix it by marking vmi_activate() as __init too.
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: fix boot hang on pre-model-15 Intel CPUs
rdmsrl_safe() does not work in very early bootup code yet, because we
dont have the pagefault handler installed yet so exception section
does not get parsed. rdmsr_safe() will just crash and hang the bootup.
So limit the MSR_IA32_MISC_ENABLE MSR read to those CPU types that
support it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
In the absence of PAT, PAGE_KERNEL_WC ends up mapping to a memory type that
gets UC behavior even in the presence of a WC MTRR covering the area in
question. By swapping to PAGE_KERNEL_UC_MINUS, we can get the actual
behavior the caller wanted (WC if you can manage it, UC otherwise).
This recovers the 40% performance improvement of using WC in the DRM
to upload vertex data.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
Stephen Hemminger
Shyam Iyer
Herbert Xu
Dhananjay Phadke
Bob Copeland
Luis R. Rodriguez
Zhu, Yi
Larry Finger
Johannes Berg
David S. Miller
Thomas Goff
Jiri Pirko
Eric Dumazet
Jesse Brandeburg
Dimitris Michailidis
Manish Katiyar
Ira W. Snyder
Anton Vorontsov
Ben Greear
Vladislav Zolotarov
Krzysztof Hałasa
Matt Helsley
Daniele Venzano
Jean Delvare
Wolfram Sang
Jesse Barnes
Harvey Harrison
Vegard Nossum
Linus Torvalds
Miklos Szeredi
Dan Carpenter
Ian Campbell
Rakib Mullick
Ingo Molnar
Eric Anholt