| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Fix all the remaining dtc 'unit_address_format' warnings except for the ones
related to 'register-bit-led'. For those, we need to decide on and document
the node name.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210823165126.2320910-1-robh@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The wrong property "atmel,shdwc-debouncer" was used to specify the
debounce delay for the shutdown controler. Replace it with the
documented and implemented property "debounce-delay-us", as mentioned
in v4 driver submission. See:
https://lore.kernel.org/r/1458134390-23847-3-git-send-email-nicolas.ferre@atmel.com/
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reported-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20210730172729.28093-1-nicolas.ferre@microchip.com/
|
|
Having a button code and not a key code causes issues with libinput.
udev won't set ID_INPUT_KEY. If it is forced, then it causes a bug
within libinput.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210402130227.21478-1-nicolas.ferre@microchip.com
|
|
atmel,wakeup-type DT property is not referenced anywhere in the current
and previous version of the code thus remove it.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nferre@kernel.org>
Link: https://lore.kernel.org/r/1609845525-10766-1-git-send-email-claudiu.beznea@microchip.com
|
|
The SCL gpio pin used by I2C bus for recovery needs to be configured as
open drain.
Fixes: 455fec938bbb ("ARM: dts: at91: sama5d2: add i2c gpio pinctrl")
Fixes: a4bd8da893a3 ("ARM: dts: at91: sama5d3: add i2c gpio pinctrl")
Fixes: 8fb82f050cf6 ("ARM: dts: at91: sama5d4: add i2c gpio pinctrl")
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20200515140001.287932-1-codrin.ciubotariu@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Indicate which i2c alias is for which connector on the board.
Specify that serial0 is for DBGU. This eases tester's life.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200514050301.147442-17-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Spare boards of duplicating the DMA bindings. Describe the flx0
DMA bindings in the SoC dtsi. Users that don't want to use DMA
for their flexcom functions have to overwrite the flexcom DMA
bindings in their board device tree.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200514050301.147442-12-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The Flexcom IP is part of the sama5d2 SoC. Move the flx0 node together
with its function definitions in sama5d2.dtsi. Boards will just fill
the pins and enable the desired functions.
There is a single functional change in this patch. With the move of the
flx0 uart5 definition in the SoC dtsi, the uart5 from
at91-sama5d27_wlsom1_ek.dts inherits the following optional property:
atmel,fifo-size = <32>;
This particular change was tested by Codrin.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20200514050301.147442-7-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Add the push button PB_USER as wakeup source
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20200401221504.41196-3-ludovic.desroches@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
The gpio property for the vbus pin doesn't match the pinctrl and is
not correct.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Fixes: 42ed535595ec "ARM: dts: at91: introduce the sama5d2 ptc ek board"
Cc: stable@vger.kernel.org # 4.19 and later
Link: https://lore.kernel.org/r/20200401221947.41502-1-ludovic.desroches@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Remove non-removable and mmc-ddr-1_8v properties from the sdmmc0
node which come probably from an unchecked copy/paste.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Fixes:42ed535595ec "ARM: dts: at91: introduce the sama5d2 ptc ek board"
Cc: stable@vger.kernel.org # 4.19 and later
Link: https://lore.kernel.org/r/20200401221504.41196-1-ludovic.desroches@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Add the i2c gpio pinctrls to support the i2c bus recovery
Signed-off-by: Kamel Bouhara <kamel.bouhara@bootlin.com>
[codrin.ciubotariu@microchip.com: removed gpio pull-ups]
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20200225155012.22764-4-codrin.ciubotariu@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Switch sama5d2 boards to the new PMC clock bindings.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Pull ARM SoC device tree updates from Arnd Bergmann:
"There are close to 800 indivudal changesets in this branch again,
which feels like a lot. There are particularly many changes for the
NVIDIA Tegra platform this time, in fact more than it has seen in the
two years since the v4.9 merge window. Aside from this, it's been
fairly normal, with lots of changes going into Renesas R-CAR, NXP
i.MX, Allwinner Sunxi, Samsung Exynos, and TI OMAP.
Most of the changes are for adding new features into existing boards,
for brevity I'm only mentioning completely new machines and SoCs here.
For the first time I think we have (slightly) more new 64-bit hardware
than 32-bit:
Two boards get added for TI OMAP: Moxa UC-2101 is an industrial
computer, see https://www.moxa.com/product/UC-2100.htm; GTA04A5 is a
minor variation of the motherboards of the GTA04 phone, see
https://shop.goldelico.com/wiki.php?page=GTA04A5
Clearfog is a nice little board for quad-core Marvell Armada 8040
network processor, see
https://www.solid-run.com/marvell-armada-family/clearfog-gt-8k/
Two additional server boards come with the Aspeed baseboard management
controllers: Stardragon4800 is an arm64 reference platform made by HXT
(based on Qualcomm's server chips), and TiogaPass is an Open Compute
mainboard with x86 CPUs. Both use the ARM11 based AST2500 chips in the
BMC.
NXP i.MX usually sees a lot of new boards each release. This time
there we only add one minor variant: ConnectCore 6UL SBC Pro uses the
same SoM design as the ConnectCore 6UL SBC Express added later.
However, there is a new chip, the i.MX6ULZ, which is an even smaller
variant of the i.MX6ULL, with features removed. There is also support
for the reference board design, the i.MX6ULZ 14x14 EVK.
A new Raspberry Pi variant gets added, this one is the CM3 compute
module based on bcm2837, it was launched in early 2017 but only now
added to the kernel, both as 32-bit and as 64-bit files, as we tend to
do for Raspberry Pi.
On the Allwinner side, everything is again about cheap development
boards, usually of the "Fruit Pi" variety. The new ones this time are:
- Orange Pi Zero Plus2: http://www.orangepi.org/OrangePiZeroPlus2/
- Orange Pi One Plus: http://www.orangepi.org/OrangePiOneplus/
- Pine64 LTS: https://www.pine64.org/?product=pine-a64-lts
- Banana Pi M2+ H5: http://www.banana-pi.org/m2plus.html
The last one of these is now a 64-bit version of the earlier Banana Pi
M2+ H3, with the same board layout.
Similarly, for Rockchips, get get another variant of the 32-bit Asus
Tinker board, the model 'S' based on rk3288, and three now boards
based on the popular RK3399 chip:
- ROC-RK3399-PC: https://libre.computer/products/boards/roc-rk3399-pc/
- Rock960: https://www.96boards.org/product/rock960/
- RockPro64: https://www.pine64.org/?page_id=61454
These are all quite powerful boards with lots of RAM and I/O, and the
RK3399 is the same chip used in several Chromebooks. Finally, we get
support for the PX30 (aka rk3326) chip, which is based on the low-end
64-bit Cortex-A35 CPU core. So far, only the evaluation board is
supported.
One more Banana Pi is added with a Mediatek chip: Banana Pi R64 is
based on the MT7622 WiFi router platform, and the first product I've
seen with a 64-bit Mediatek chip in that market:
http://www.banana-pi.org/r64.html
For HiSilicon, we gain support for the Hi3670 SoC and HiKey 370
development board, which are similar to the Hi3660 and Hikey 360
respectively, but add support for an NPU.
Amlogic gets initial support for the Meson-G12A chip (S905D2), another
quad-core Cortex-A53 SoC, and its evaluation platform. On the 32-bit
side, we gain support for an actual end-user product, the Endless
Computers Endless Mini based on Meson8b (S805), see
https://endlessos.com/computers/
Qualcomm adds support for their MSM8998 SoC and evaluation platform.
This chip is commonly known as the Snapdragon 835, and is used in
high-end phones as well as low-end laptops.
For Renesas, a very bare support for the r8a774a1 (RZ/G2M) is added,
but no boards for this one. However, we do add boards for the
previously added r8a77965 (R-Car M3-N): the M3NULCB Kingfisher and the
M3NULCB Starter Kit Pro.
While we have lots of DT changes for NVIDIA to update the existing
files, the only board that gets added is the Toradex Colibri T20 on
Colibri Evaluation Board for the old Tegra2.
Synaptics add support for their AS370 SoC, which is part of the
(formerly Marvell) Berlin line of set-top-box chips used e.g. in the
various Google Chromecast. Only the .dtsi gets added at this point, no
actual machines"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (721 commits)
ARM: dts: socfgpa: remove ethernet aliases from dtsi
arm64: dts: stratix10: add ethernet aliases
dt-bindings: mediatek: Add bindig for MT7623 IOMMU and SMI
dt-bindings: mediatek: Add JPEG Decoder binding for MT7623
dt-bindings: iommu: mediatek: Add binding for MT7623
dt-bindings: clock: mediatek: add support for MT7623
ARM: dts: mvebu: armada-385-db-88f6820-amc: auto-detect nand ECC properites
ARM: dts: da850-lego-ev3: slow down A/DC as much as possible
ARM: dts: da850-evm: Enable tca6416 on baseboard
arm64: dts: uniphier: Add USB2 PHY nodes
arm64: dts: uniphier: Add USB3 controller nodes
ARM: dts: uniphier: Add USB2 PHY nodes
ARM: dts: uniphier: Add USB3 controller nodes
arm64: dts: meson-axg: s400: disable emmc
arm64: dts: meson-axg: s400: add missing emmc pwrseq
arm64: dts: clearfog-gt-8k: add PCIe slot description
ARM: dts: at91: sama5d4_xplained: even nand memory partitions
ARM: dts: at91: sama5d3_xplained: even nand memory partitions
ARM: dts: at91: at91sam9x5cm: even nand memory partitions
ARM: dts: at91: sama5d2_ptc_ek: fix bootloader env offsets
...
|
|
The offsets for the bootloader environment and its redundant partition
were inverted. Fix the addresses to match our nand flash map available at:
http://www.at91.com/linux4sam/pub/Linux4SAM/SambaSubsections//demo_nandflash_map_lnx4sam5x.png
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
|
|
The drive strength has to be set to medium otherwise some data
corruption may happen.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Using compatible strings without the <manufacturer> part for at24 is
now deprecated. Use a correct 'atmel,<model>' value.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Use tcb0 for timers as selected in sama5_defconfig.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Add the official SAMA5D2 Peripheral Touch Controller Evaluation
Kit board.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
Rob Herring
Nicolas Ferre
Ludovic Desroches
Claudiu Beznea
Codrin Ciubotariu
Tudor Ambarus
Kamel Bouhara
Alexandre Belloni
Linus Torvalds
Bartosz Golaszewski