aboutsummaryrefslogtreecommitdiffstats
path: root/arch/arm/boot/dts/at91-sama5d4_xplained.dts (follow)
AgeCommit message (Collapse)AuthorFilesLines
2017-05-31ARM: dts: at91: Switch to the new NAND bindingsBoris Brezillon1-32/+51
Use the new EBI/NAND bindings to declare NAND chips and remove old NAND nodes along the way. Note that we keep using old bindings in at91rm9200.dtsi because this SoC is not supported by the EBI driver. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Tested-by: Peter Rosin <peda@axentia.se> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2017-01-19ARM: dts: at91: Enable DMA on sama5d4_xplained consoleAlexandre Belloni1-0/+2
Enable DMA on usart3 to get a more reliable console. This is especially useful for automation and kernelci were a kernel with PROVE_LOCKING enabled is quite susceptible to character loss, resulting in tests failure. Cc: stable <stable@vger.kernel.org> #v4.1+ Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2017-01-10ARM: dts: at91: sama5d4 Xplained: enable UART1 node with DMANicolas Ferre1-0/+6
Enable UART1 and use DMA configuration with it. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-07-15ARM: dts: at91: sama5d4_xplained: fix regulator namesAlexandre Belloni1-2/+2
vcc_3v3_reg and vcc_mmc1_reg are fixed regulators and don't need a reg property. Remove their unit-address. Solves: Warning (unit_address_vs_reg): Node /fixedregulator@0 has a unit name, but no reg property Warning (unit_address_vs_reg): Node /fixedregulator@1 has a unit name, but no reg property Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-03-22ARM: dts: at91: sama5d4 Xplained: don't disable hsmci regulatorLudovic Desroches1-0/+1
If enabling the hsmci regulator on card detection, the board can reboot on sd card insertion. Keeping the regulator always enabled fixes this issue. Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> Fixes: 8d545f32bd77 ("ARM: at91/dt: sama5d4 xplained: add regulators for v(q)mmc1 supplies") Cc: stable@vger.kernel.org #4.3 and later Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2016-01-27ARM: dts: at91: sama5d4 xplained: fix phy0 IRQ typeNicolas Ferre1-1/+1
For phy0 KSZ8081, the type of GPIO IRQ should be "level low" instead of "edge falling". Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Fixes: 38153a017896 ("ARM: at91/dt: sama5d4: add dts for sama5d4 xplained board") Cc: <stable@vger.kernel.org> # 4.1+
2016-01-27ARM: dts: at91: sama5d4 xplained: properly mux phy interruptAlexandre Belloni1-0/+6
No interrupt were received from the phy because PIOE 1 may not be properly muxed. It prevented proper link detection, especially since commit 321beec5047a ("net: phy: Use interrupts when available in NOLINK state") disables polling. Cc: <stable@vger.kernel.org> # 4.4 Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2015-11-16ARM: at91/dt: remove bootargsAlexandre Belloni1-1/+0
Passing earlyprintk in the bootargs may crash the board as it depends on having a sane DEBUG_UART_PHYS configured which is not always the case. Also remove ignore_loglevel Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2015-11-16ARM: at91/dt: remove leftovers clock definitionAlexandre Belloni1-9/+0
The clocks group properties and the clock@0 node are useless, remove them to avoid copy pasting in future device trees. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2015-11-16ARM: at91/dt: replace gpio-key,wakeup with wakeup-source propertySudeep Holla1-1/+1
Though the keyboard driver for GPIO buttons(gpio-keys) will continue to check for/support the legacy "gpio-key,wakeup" boolean property to enable gpio buttons as wakeup source, "wakeup-source" is the new standard binding. This patch replaces the legacy "gpio-key,wakeup" with the unified "wakeup-source" property in order to avoid any futher copy-paste duplication. Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com> Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2015-09-18ARM: at91/dt: sama5d4 xplained: enable the led D8Josh Wu1-1/+1
Enable D8 led as now the pioD is available. D8 is the power led and is on by default. Signed-off-by: Josh Wu <josh.wu@atmel.com> [nicolas.ferre@atmel.com: split the patch in 2] Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2015-07-28ARM: at91/dt: sama5d4: move ADC pinctrl to board device treesAlexandre Belloni1-0/+9
The ADC pinctrl is board specific, move it to the board device trees. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2015-06-04ARM: at91/dt: sama5d4 xplained: use stdout-pathAlexandre Belloni1-1/+2
Use stdout-path to specify the console and remove the console argument from the kernel command line. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2015-05-19ARM: at91/dt: sama5d4 xplained: add regulators for v(q)mmc1 suppliesLudovic Desroches1-0/+20
Add vcc_mmc1 fixed regulator to remove the 'no vmmc regulator found' warning when probing the mmc1 device. Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2015-05-19ARM: at91/dt: sama5d4 xplained: add spi1 on j14 connectorNicolas Ferre1-0/+5
Route SPI1 on the Arduino "in the middle" spi connector. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2015-03-04ARM: at91/dt: sama5d4 xplained: add i2c0Nicolas Ferre1-0/+4
Add i2c0 aka twi0 on sama5d4 xplained board. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2015-03-04ARM: at91/dt: sama5d4: add dts for sama5d4 xplained boardJosh Wu1-0/+237
Add at91 sama5d4 xplained board support. Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.