| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Samsung DTS changes for DMC driver for v5.5
Add bindings and update device tree sources of Exynos5422 platforms with
new Dynamic Memory Controller nodes and properties.
* tag 'samsung-dt-dmc-5.5' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
dt-bindings: memory-controllers: exynos5422-dmc: Correct example syntax and memory region
ARM: dts: exynos: Add interrupts to DMC controller in Exynos5422
ARM: dts: exynos: Extend mapped region for DMC on Exynos5422
dt-bindings: memory-controllers: exynos5422-dmc: Add interrupt mode
dt-bindings: ddr: Add bindings for Samsung LPDDR3 memories
ARM: dts: exynos: Add DMC device to Exynos5422 and Odroid XU3-family boards
ARM: dts: exynos: Add syscon compatible to clock controller on Exynos542x
dt-bindings: memory-controllers: Add Exynos5422 DMC device description
dt-bindings: ddr: Add bindings for LPDDR3 memories
dt-bindings: ddr: Rename lpddr2 directory
Link: https://lore.kernel.org/r/20191021180453.29455-6-krzk@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add interrupts to Dynamic Memory Controller in Exynos5422 and Odroid
XU3-family boards. It will be used instead of devfreq polling mode
governor. The interrupt is connected to performance counters private
for DMC, which might track utilisation of the memory channels.
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
DMC Adaptive Voltage and Frequency Scaling driver in interrupt mode
needs to access registers at address offset near 0x10000. These
registers are private DMC performance counters, which might be used
as interrupt trigger when overflow. Potential usage is to skip polling
in devfreq framework and switch to interrupt managed bandwidth control.
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Change representation of phandle array as then dt-schema counts number
of its items properly.
Signed-off-by: Maciej Falkowski <m.falkowski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Add description of Dynamic Memory Controller and PPMU counters to
Exynos5422 and Odroid XU3/XU4/HC1 boards. They are used by
exynos5422-dmc driver. There is a definition of the memory chip, which
is then used during calculation of timings for each OPP.
The algorithm in the driver needs these two sets to bound the timings.
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
In order to get the clock by phandle and use it with regmap it needs to be
compatible with syscon. The DMC driver uses two registers from clock
register set and needs the regmap of them.
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Add a power domain for G3D/Mali device present in Exynos542x/5800 SoCs.
Node for the Mali device will be added by a separate patch.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
DT nodes should be sorted by 'reg' property, so move MSC power domain
node in exynos5420.dtsi to the end of power domains to keep them sorted.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Move the ADC from exynos5420.dtsi to a shared file between Exynos5410 and
Exynos542x: exynos54xx.dtsi. Enable the ADC on Odroid XU board.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
The cpus node is a top-level node, not inside the soc. Therefore its
OPP tables should be there as well.
This also fixes the DTC warnings like:
arch/arm/boot/dts/exynos5420.dtsi:46.37-109.5:
Warning simple_bus_reg): /soc/opp_table0: missing or empty reg/ranges property
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
The SoC name EXYNOS5420 was misspelled.
Signed-off-by: Benjamin Drung <bdrung@posteo.de>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Remove no longer needed samsung thermal properties.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
There are 3 scaler devices in Exynos5420 SoCs, all are a part of MSCL
power domain. MSCL power domain and SYSMMU controllers (two per each
scaler device) have been already added to exynos5420.dtsi earlier,
so bind them to newly added devices.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find arch/arm/boot/dts -type f \( -iname "*.dts" -o -iname "*.dtsi" \) -exec sed -i \
-e "s/@\([0-9a-fA-FxX\.;:#]\+\)\s*{/@\L\1 {/g" -e "s/@0x\(.*\) {/@\1 \
{/g" -e "s/@0\+\(.\+\) {/@\1 {/g" {} +
For simplicity, two sed expressions were used to solve each warnings separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace: https://elinux.org/Device_Tree_Linux#Linux_conventions
This will solve also a side effect warning:
Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format error, expected "<lower>"
This is a follow up to commit 4c9847b7375a ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
[krzk: Rerun the command to include few more changes, adjust the commit msg]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
The PMU node is the actual block responsible for power management,
including typical Exynos on/off/restart procedures. Therefore the
syscon poweroff and restart nodes logically belong to it.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
Handling of special clock operations on power domain on/off sequences
has been moved to respective Exynos clock controller drivers and clock
properties have been marked as deprecated. Remove all clock properties
from existing Exynos power domain nodes, as they are no longer used.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Replace GPL v2.0 license statements with SPDX license identifiers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Convert all hex addresses in node unit addresses to lower case to fix warnings
like:
arch/arm/boot/dts/exynos5422-odroidhc1.dtb: Warning (simple_bus_reg):
Node /soc/nocp@10CA1000 simple-bus unit address format error, expected "10ca1000"
Conversion was done using sed:
$ sed -e 's/@\([a-zA-Z0-9_-]*\) {/@\L\1 {/' -i arch/arm/boot/dts/exynos*.dts*
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Add nodes for the True Random Number Generator found in Samsung Exynos
5250+ SoCs.
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Add nodes for Pseudo Random Number Generator in dts files describing
Exynos5 chips.
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Audio power domain includes following hardware modules: Pin controller
for GPZ bank, AudioSS clock controller, PL330 ADMA device and Exynos I2S
controller.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Current the node is only defined in the exynos5250 DT, while
the corresponding SYSMMUs are also to be found in the exynos5420
DT. Move the node to exynos5 and only setup the SYSMMUs in the
corresponding DT.
Disable the node by default, since exynos5410 also includes
the dtsi, but currently does not define the G2D clock.
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
[mszyprow: rephrased commit message]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
The new sound card DT binding is used for Odroid XU3 in order
to properly support the HDMI audio path. Clocks configuration is
changed so the I2S controller is now the bit clock and the frame clock
master. The EPLL output clock is now the audio root clock adjusted to
each audio sample rate.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Pull "Samsung DTS ARM changes for 4.15" from Krzysztof Kozłowski:
1. Add new board: Hardkernel Odroid HC1.
2. Fix incomplete Odroid-XU3/4 thermal-zones definition leading to
possible overheat if first pair of A7+A15 cores is idle but rest of
CPUs are busy.
3. Add capacity-dmips-mhz properties for CPUs of octa-core SoCs.
4. Add power button to Odroid XU3/4.
5. Improvements in Gscaler, HDMI and Mixer blocks on Exynos5.
6. Add suspend quirk to DWC3 USB controller to fix enumeration of
SuperSpeed devices on Odroid XU4.
7. Add HDMI and MHL to Trats2.
8. Cleanups (redundant properties and nodes).
* tag 'samsung-dt-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
dt-bindings: samsung: Document binding for new Odroid HC1 board
ARM: dts: exynos: Add HDMI and Sil9234 to Trats2 board
ARM: dts: exynos: Add support for Hardkernel's Odroid HC1 board
ARM: dts: exynos: Move audio clocks configuration to odroidxu3-audio.dtsi
ARM: dts: exynos: Add dwc3 SUSPHY quirk
ARM: dts: exynos: Add status property to Exynos 542x Mixer nodes
ARM: dts: exynos: Add status property to Exynos 5250 HDMI and Mixer nodes
ARM: dts: exynos: Cleanup HDMI DCC definitions on Exynos5250 and Exynos542x boards
ARM: dts: exynos: Move HDMI PHY node from boards to exynos5250.dtsi
ARM: dts: exynos: Use specific compatibles for proper Gscaler limits on Exynos5250 and Exynos5420
ARM: dts: exynos: Remove redundant interrupt properties in gpio-keys on Odroid boards
ARM: dts: exynos: Add power button for Odroid XU3/4
ARM: dts: exynos: Remove the display-timing and delay from Rinato
ARM: dts: exynos: add exynos5422 cpu capacity-dmips-mhz information
ARM: dts: exynos: add exynos5420 cpu capacity-dmips-mhz information
ARM: dts: exynos: fix incomplete Odroid-XU3/4 thermal-zones definition
|
|
Fix dtc warnings for 'simple_bus_reg' due to leading 0s. Converted using
the following command:
perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find arch/arm/boot/dts -type -f -name '*.dts*'
Dropped changes to ARM, Ltd. boards LED nodes and manually fixed up some
occurrences of uppercase hex.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
HDMI support requires some additional off-SoC logic, so Mixer device (part
of HDMI display path) should be disabled by default in SoC dtsi and enabled
then in each board dts. This patch unifies Mixer handling with other
Exynos SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Exynos 5250 and 5420 have different hardware rotation limits. However,
currently it uses only one compatible - "exynos5-gsc". Since we have
to distinguish between these two, we add different compatible.
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Replace hard-coded values of type of GIC interrupt and its flags with
respective macros from header to increase code readability.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Exynos5250 and Exynos542x SoCs have the same CEC hardware module as
Exynos4 SoC series, so enable support for it using the same compatible
string.
Tested on Odroid XU3 (Exynos5422) and Google Snow (Exynos5250) boards.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Compiling the DT file with W=1, DTC warns like follows:
Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 has a
unit name, but no reg property
Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
[k.kozlowski: Split patch per ARM and ARM64]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
In Odroid XU3 Lite board, the temperature levels reported for thermal
zone 0 were weird. In warm room:
/sys/class/thermal/thermal_zone0/temp:32000
/sys/class/thermal/thermal_zone1/temp:51000
/sys/class/thermal/thermal_zone2/temp:55000
/sys/class/thermal/thermal_zone3/temp:54000
/sys/class/thermal/thermal_zone4/temp:51000
Sometimes after booting the value was even equal to ambient temperature
which is highly unlikely to be a real temperature of sensor in SoC.
The thermal sensor's calibration (trimming) is based on fused values.
In case of the board above, the fused values are: 35, 52, 43, 58 and 43
(corresponding to each TMU device). However driver defined a minimum value
for fused data as 40 and for smaller values it was using a hard-coded 55
instead. This lead to mapping data from sensor to wrong temperatures
for thermal zone 0.
Various vendor 3.10 trees (Hardkernel's based on Samsung LSI, Artik 10)
do not impose any limits on fused values. Since we do not have any
knowledge about these limits, use 0 as a minimum accepted fused value.
This should essentially allow accepting any reasonable fused value thus
behaving like vendor driver.
The exynos5420-tmu-sensor-conf.dtsi is copied directly from existing
exynos4412 with one change - the samsung,tmu_min_efuse_value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
|
|
Provide human readable names for all power domains defined in Exynos SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
UART modules can use DMA for offloading data transfers and reducing
interrupts, so enable this feature for Exynos5 boards. Tested on
Google ChromeBook Snow (Exynos5250), Odroid XU (Exynos5410) and Odroid
XU3 (Exynos5422) boards.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Interrupt of type IRQ_TYPE_NONE is not allowed for GIC interrupts and
generates an error:
genirq: Setting trigger mode 0 for irq 16 failed (gic_set_type+0x0/0x68)
The GIC requires shared interrupts to be edge rising or level high.
Platform declares support for both. Arbitrarily choose level high
everywhere hoping it will work on each platform.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reported-by: Alban Browaeys <alban.browaeys@gmail.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
|
|
Topic branch for adding Exynos 5410 Odroid XU board for v4.8.
This brings support for Hardkernel's Odroid XU board. It was the first
design with big.LITTLE SoC from Samsung: Exynos5410. The board is not
very popular. Newer XU3 and XU4 got more attention.
Board details:
1. Exynos5410 octa-core (A15+A7, however as of now only one cluster is
enabled),
2. 2 GB DDR3 RAM,
3. PowerVR SGX544MP3 GPU (not enabled in DTS),
4. USB 3.0 Host x 1, USB 3.0 OTG x 1, USB 2.0 Host x 4,
5. HDMI 1.4a, MIPI DSI and Display Port (Display Port not on all of
revisions though),
6. eMMC 4.5 and microSD slots.
* tag 'samsung-dt-odroid-xu-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (28 commits)
ARM: dts: exynos: Add watchdog and Security SubSystem to Exynos5410
ARM: dts: exynos: Configure PWM, usb3503, PMIC and thermal on Odroid XU board
ARM: dts: exynos: Add Thermal Management Unit to Exynos5410
ARM: dts: exynos: Interrupt for USB DWC3-1 differs between Exynos5420 and 5410
dt-bindings: clock: Add watchdog and SSS clock IDs to Exynos5410
dt-bindings: clock: Add TMU clock ID to Exynos5410
ARM: dts: exynos: Add RTC and I2C to Exynos5410
ARM: dts: exynos: Add I2C, PWM and UART pinctrl to Exynos5410
ARM: dts: exynos: Move HSI2C nodes to exynos54xx.dtsi
ARM: dts: exynos: Add initial support for Odroid XU board
ARM: dts: exynos: Add USB to Exynos5410
ARM: dts: exynos: Move common Exynos5410/542x/5800 nodes to new DTSI
ARM: dts: exynos: MCT is not an interrupt controller and extend length of iomap
ARM: dts: exynos: Enable UART3 on Exynos5410
ARM: dts: exynos: Include common exynos5 in exynos5410.dtsi
ARM: dts: exynos: Move Exynos5250 and Exynos5420 nodes under soc
ARM: dts: exynos: Use phandle to get parent node in exynos5250-snow
ARM: dts: exynos: Prepare for inclusion of exynos5.dtsi in exynos5410.dtsi
ARM: dts: exynos: Move common nodes to exynos5.dtsi
ARM: dts: exynos: Split Odroid XU3 LEDs to separate DTSI
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Move watchdog and Security SubSystem nodes from exynos5420.dtsi to file
shared with Exynos5410 and configure the clocks on the latter.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
|
|
On Exynos5410 the SPI interrupt for second USB DWC3 (called DRD: Dual
Role Device) is different - 200 instead of 73.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
The USI/HSI2C nodes can be mostly shared between Exynos5420 and
Exynos5410 so move them to common DTSI.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
|
|
Move USB 3.0 DWC and 2.0 EHCI/OHCI nodes from exynos5420.dtsi to
exynos54xx.dtsi common for entire family. For Exynos542x/5800 this
should not have functional impact but for Exynos5410 this effectively
adds USB support.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
|
|
The Exynos5410/542x/5800 are very similar designs. Create a new
DTSI with common nodes to remove DTS duplication. Although currently
only MCT and SysRAM are shared but in future more nodes will be added to
the common file.
The patch should not have functional impact.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
|
|
Multi-Core Timer generates interrupts but it is not really an interrupt
controller so remove the "interrupt-controller" and "interrupt-cells"
properties. Additionally extend the length of mapped memory to cover all
registers (last SFR is at 0x0A40).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
|
|
The conventions is to put SoC devices under 'soc' node. In fact other
our DTSes (like exynos3250.dtsi or exynos5410.dtsi) already follow it.
Adjust exynos5250 and exynos5420 DTSI to follow this convention. This is
also necessary for the upcoming change in exynos5410.dtsi to inherit
from common exynos5.dtsi.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
|
|
Exynos5420 and Exynos5250 share some nodes: the PWM, syscon
(sysreg_system_controller) and first four I2C controllers. Move them to
parent DTSI to avoid duplication.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
|
|
Since commit 218e1496135e ("i2c: exynos5: add support for HSI2C on
Exynos5260 SoC") the "samsung,exynos5-hsi2c" is deprecated in favor of
SoC version specific: "samsung,exynos5250-hsi2c".
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
The MFC IP is also inter-connected by an Async-Bridge so the CLK_ACLK333
has to be ungated during a power domain switch. Trying to do it when the
clock is gated will fail and lead to an imprecise external abort error
when the driver tries to access the MFC registers with the PD disabled.
For example, if the s5p-mfc module is removed and the MFC PD turned off:
[ 186.835606] Power domain power-domain@10044060 disable failed
[ 186.835671] s5p-mfc 11000000.codec: Removing 11000000.codec
[ 186.837670] Power domain power-domain@10044060 disable failed
And when the module is inserted again:
[ 2395.176956] s5p_mfc_wait_for_done_dev:34: Interrupt (dev->int_type:0, command:12) timed out
[ 2395.177031] s5p_mfc_init_hw:272: Failed to load firmware
[ 2395.177384] Unhandled fault: imprecise external abort (0x1406) at 0x00000000
[ 2395.177441] pgd = ec3b4000
[ 2395.177467] [00000000] *pgd=00000000
[ 2395.177507] Internal error: : 1406 [#1] PREEMPT SMP ARM
[ 2395.177550] Modules linked in: s5p_mfc mwifiex_sdio mwifiex uvcvideo s5p_jpeg v4l2_mem2mem videobuf2_vmalloc videobuf2_dma_contig videobuf2_memops videobuf2_v4l2 videobuf2_core v4l2_common videodev media [last unloaded: s5p_mfc]
[ 2395.177774] CPU: 1 PID: 2382 Comm: v4l_id Tainted: G W 4.6.0-rc6-next-20160502-00010-g7730dc64d2c1-dirty #179
[ 2395.177857] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[ 2395.177906] task: ed275500 ti: e6c8c000 task.ti: e6c8c000
[ 2395.177996] PC is at s5p_mfc_reset+0x1c4/0x284 [s5p_mfc]
[ 2395.178057] LR is at s5p_mfc_reset+0x1a4/0x284 [s5p_mfc]
This patch fixes this issue by adding the CLK_ACLK333 as an Async-Bridge
clock for the MFC power domain, so the PD configuration works properly.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
Pull ARM SoC late DT updates from Arnd Bergmann:
"This is a collection of a few late fixes and other misc stuff that had
dependencies on things being merged from other trees.
The Renesas R-Car power domain handling, and the Nvidia Tegra USB
support both hand notable changes that required changing the DT
binding in a way that only provides compatibility with old DT blobs on
new kernels but not vice versa. As a consequence, the DT changes are
based on top of the driver changes and are now in this branch.
For NXP i.MX and Samsung Exynos, the changes in here depend on other
changes that got merged through the clk maintainer tree"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (35 commits)
ARM: dts: exynos: Add support of Bus frequency using VDD_INT for exynos5422-odroidxu3
ARM: dts: exynos: Add bus nodes using VDD_INT for Exynos542x SoC
ARM: dts: exynos: Add NoC Probe dt node for Exynos542x SoC
ARM: dts: exynos: Add support of bus frequency for exynos4412-trats/odroidu3
ARM: dts: exynos: Expand the voltage range of buck1/3 regulator for exynos4412-odroidu3
ARM: dts: exynos: Add support of bus frequency using VDD_INT for exynos3250-rinato
ARM: dts: exynos: Add exynos4412-ppmu-common dtsi to delete duplicate PPMU nodes
ARM: dts: exynos: Add bus nodes using VDD_MIF for Exynos4210
ARM: dts: exynos: Add bus nodes using VDD_INT for Exynos4x12
ARM: dts: exynos: Add bus nodes using VDD_MIF for Exynos4x12
ARM: dts: exynos: Add bus nodes using VDD_INT for Exynos3250
ARM: dts: exynos: Add DMC bus frequency for exynos3250-rinato/monk
ARM: dts: exynos: Add DMC bus node for Exynos3250
ARM: tegra: Enable XUSB on Nyan
ARM: tegra: Enable XUSB on Jetson TK1
ARM: tegra: Enable XUSB on Venice2
ARM: tegra: Add Tegra124 XUSB controller
ARM: tegra: Move Tegra124 to the new XUSB pad controller binding
ARM: dts: r8a7794: Use SYSC "always-on" PM Domain
ARM: dts: r8a7793: Use SYSC "always-on" PM Domain
...
|
|
This patch adds the AMBA bus nodes using VDD_INT for Exynos542x SoC.
Exynos542x has the following AMBA buses to translate data between
DRAM and sub-blocks.
Following list specifies the detailed correlation between sub-block and clock:
- CLK_DOUT_ACLK400_WCORE clock for WCORE's AXI
- CLK_DOUT_ACLK100_NOC for NoC (Network on Chip)'s AXI
- CLK_DOUT_PCLK200_FSYS for FSYS's APB
- CLK_DOUT_ACLK200_FSYS for FSYS's AXI
- CLK_DOUT_ACLK200_FSYS2 for FSYS2's AXI
- CLK_DOUT_ACLK333 for MFC's AXI
- CLK_DOUT_ACLK266 for GEN's AXI
- CLK_DOUT_ACLK66 for PERIC/PERIR's AXI
- CLK_DOUT_ACLK333_G2D for G2D's AXI
- CLK_DOUT_ACLK266_G2D for ACP's AXI
- CLK_DOUT_ACLK300_JPEG for JPEG's AXI
- CLK_DOUT_ACLK166 for JPEG's APB
- CLK_DOUT_ACLK300_DISP1 for FIMD's AXI
- CLK_DOUT_ACLK400_DISP1 for DISP1's AXI
- CLK_DOUT_ACLK300_GSCL for GSCL Scaler's AXI
- CLK_DOUT_ACLK400_MSCL for MSCL's AXI
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
This patch adds the NoCP (Network on Chip Probe) Device Tree node
to measure the bandwidth of memory and g3d in Exynos542x SoC.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
This patch changes the compatible of Exynos5420 fimd
to "exynos5420-fimd". To support MIC bypass from display
path, the new compatible is introduced for Exynos5420.
Cc: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
Fix following DTC warnings in all Exynos542x/5800 boards:
Warning (unit_address_vs_reg): Node /video-phy@10040728 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /video-phy@10040714 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /usb@12000000 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /usb@12000000/dwc3 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /usb@12400000 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /usb@12400000/dwc3 has a reg or ranges property, but no unit name
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
|
Olof Johansson
Lukasz Luba
Maciej Falkowski
Marek Szyprowski
Krzysztof Kozlowski
Benjamin Drung
Bartlomiej Zolnierkiewicz
Andrzej Pietrasiewicz
Mathieu Malaterre
Łukasz Stelmach
Tobias Jakobi
Sylwester Nawrocki
Arnd Bergmann
Rob Herring
Hoegeun Kwon
Viresh Kumar
Krzysztof Kozlowski
Javier Martinez Canillas
Linus Torvalds
Chanwoo Choi
Chanho Park