| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Boards based on imx28 have duplicate memory nodes:
- One coming from the board dts file: memory@
- One coming from the imx28.dtsi file.
Fix the duplication by removing the memory node from the dtsi file
and by adding 'device_type = "memory";' in the board dts.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
dtc has new checks for SPI buses. Fix the warnings in node names and
unit-addresses.
There's over 100 warnings for FSL boards, a few examples:
arch/arm/boot/dts/imx28-duckbill-2-spi.dtb: Warning (spi_bus_bridge): /apb@80000000/apbh@80000000/ssp@80014000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/imx53-ppd.dtb: Warning (spi_bus_bridge): /soc/aips@50000000/spba@50000000/ecspi@50010000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/imx6dl-colibri-eval-v3.dtb: Warning (spi_bus_reg): /soc/aips-bus@2000000/spba-bus@2000000/spi@2014000/mcp251x@1: SPI bus unit address format error, expected "0"
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Li Yang <leoyang.li@nxp.com>
Cc: Stefan Agner <stefan@agner.ch>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fix the following warnings from dtc by adding the unit name to memory
nodes:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Converted using the following command:
perl -p0777i -e 's/memory \{\n\t\treg = \<0x+([0-9a-f])/memory\@$1$\0000000 \{\n\t\treg = <0x$1/m' `find ./arch/arm/boot/dts -name "imx*"`
The files below were manually fixed:
-imx1-ads.dts
-imx1-apf9328.dts
-imx6q-pistachio.dts
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This patch updates the Duckbill device tree and synchronize it with
the vendor distributed file. The changes in mostly pin-muxing stuff,
but also some minor fixes. In detail:
- enable SPI pins
- enable I2C pins
- enable UART pins
- enable LRADC pin
- adjust USB DR mode
- add default triggers for LEDs
- get rid of regulators simple-bus container
- adjust phy reset duration
According to phy datasheet, 25ms are sufficient. This also reduces
the time to boot the system.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Use GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW instead of 0 and 1.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Fix a copy & paste error: on duckbills the GPIO used for resetting
the ethernet phy differs from FSL's MX28EVK board.
Reported-by: Stefan Wahren <info@lategoodbye.de>
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
I2SE's duckbills are only equipped with a micro SD card slot and
thus only provide a 4-bit interface.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
|
|
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
Fabio Estevam
Rob Herring
Marco Franchi
Michael Heimpold