| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The Marvell RTC on Kirkwood makes use of the runit clock. Ensure the
driver clk_prepare_enable() this clock, otherwise there is a danger
the SoC will lockup when accessing RTC registers with the clock
disabled.
Reported-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The kirkwood SoC GPIO cores use the runit clock. Add code to
clk_prepare_enable() runit, otherwise there is a danger of locking up
the SoC by accessing the GPIO registers when runit clock is not
ticking.
Reported-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
When DT support for kirkwood was first introduced, there was no clock
infrastructure. As a result, we had to manually pass the
clock-frequency to the driver from the device node.
Unfortunately, on kirkwood, with minimal config or all module configs,
clock-frequency breaks booting because of_serial doesn't consume the
gate_clk when clock-frequency is defined.
The end result on kirkwood is that runit gets gated, and then the boot
fails when the kernel tries to write to the serial port.
Fix the issue by removing the clock-frequency parameter from all
kirkwood dts files.
Booted on dreamplug without earlyprintk and successfully logged in via
ttyS0.
Reported-by: Simon Baatz <gmbnomis@gmail.com>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Now that the SDIO controller has a Device Tree binding, let's use it
in kirkwood.dtsi.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The gpio controller on kirkwood can provide interrupts but is missing
the #interrupt-cells property. This patch just adds it to both gpio
controllers.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Without the clock being held by a driver, it gets turned off at a bad
time causing the SoC to lockup. This is often during reboot.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Stefan Peter <s.peter@mpl.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Pull ARM SoC updates for Marvell mvebu/kirkwood from Olof Johansson:
"This is a branch with updates for Marvell's mvebu/kirkwood platforms.
They came in late-ish, and were heavily interdependent such that it
didn't make sense to split them up across the cross-platform topic
branches. So here they are (for the second release in a row) in a
branch on their own."
* tag 'mvebu' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (88 commits)
arm: l2x0: add aurora related properties to OF binding
arm: mvebu: add Aurora L2 Cache Controller to the DT
arm: mvebu: add L2 cache support
dma: mv_xor: fix error handling path
dma: mv_xor: fix error checking of irq_of_parse_and_map()
dma: mv_xor: use request_irq() instead of devm_request_irq()
dma: mv_xor: clear the window override control registers
arm: mvebu: fix address decoding armada_cfg_base() function
ARM: mvebu: update defconfig with I2C and RTC support
ARM: mvebu: Add SATA support for OpenBlocks AX3-4
ARM: mvebu: Add support for the RTC in OpenBlocks AX3-4
ARM: mvebu: Add support for I2C on OpenBlocks AX3-4
ARM: mvebu: Add support for I2C controllers in Armada 370/XP
arm: mvebu: Add hardware I/O Coherency support
arm: plat-orion: Add coherency attribute when setup mbus target
arm: dma mapping: Export a dma ops function arm_dma_set_mask
arm: mvebu: Add SMP support for Armada XP
arm: mm: Add support for PJ4B cpu and init routines
arm: mvebu: Add IPI support via doorbells
arm: mvebu: Add initial support for power managmement service unit
...
|
|
Select the generic mvebu kirkwood pincltr driver and generic mvebu
gpio driver. This requires minor changes to the DT, and the calls to
configure plat-orion gpio driver are removed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Michael Walle <michael@walle.cc>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Tested-by: Joshua Coombs <josh.coombs@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Now that the EHCI driver has DT support, drop old style configuration
of it and add DT in its place. Since all the boards enable the EHCI,
enable it by default in kirkwood.dtsi. Any new boards which don't have
USB can specifically disable it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Use DT to describe the two XOR DMA engines on Kirkwood. Remove the
C code initialization.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
|
|
With true DT clock providers available switch Kirkwood clock setup in
DT- enabled boards. While AUXDATA can be removed completely from bus
probing, some devices still don't know about DT. Therefore, some clkdev
aliases are created until these devices also move to DT.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
|
|
Based on work by Michael Walle and Jason Cooper.
Added support for getting the interrupt number and address of SRAM
from DT.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Conflicts:
arch/arm/mach-kirkwood/board-dt.c
|
|
Add support for instantiating this driver from device tree, and add
the necassary DT information to the kirkwood.dtsi file.
This is based on previous work by Michael Walle and Jason Cooper.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Josh Coombs <josh.coombs@gmail.com>
|
|
Add device tree support to the Orion watchdog timer, and enable its
use in the kirkwood devices using device tree.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
|
|
The MV64XXX I2C driver needs a clock in order to calculate the baud
rate factors. So add an clk to the clk tree. Also add the base DT
properties for kirkwood devices.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Conflicts:
arch/arm/mach-kirkwood/common.c
|
|
Populate the devices with auxdata to set the device names which are used by
clkdev to lookup the clocks.
Signed-off-by: Michael Walle <micheal@walle.cc>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
v2: Add interrupts properties, although not used.
|
|
Both IRQ and GPIO controllers can now be represented in DT. The IRQ
controllers are setup first, and then the GPIO controllers. Interrupts
for GPIO lines are placed directly after the main interrupts in the
interrupt space.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Josh Coombs <josh.coombs@gmail.com>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
|
|
It has been decided to use marvell, not mrvl, in the compatibility
property. Search & replace.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
|
|
Add default configuration for NAND, to be enabled in your board config. Ensure
clock gating is set appropriately when the NAND is enabled.
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
Define both uarts in kirkwood.dtsi as they are common to all kirkwood
SoCs. Each board may enable all or none of them, so they are disabled
by default. uart0 is enabled for the dreamplug.
tclk can vary for each board, so we leave it undefined in the kirkwood
dtsi. Each board can then set it as appropriate when enabling the uart.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Also, use inclusive register size for uart0.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Initially, copied guruplug-setup.c and did s/guruplug/dreamplug/g.
Then, switched to SPI based NOR flash.
After talking to Arnd Bergman, chose an incremental approach to adding
devicetree support. First, we use the dtb to tell us we are on the
dreamplug, then we gradually port over drivers.
Driver porting will start with the uart (see next patch), and progress
from there. Possibly, spi/flash/partitions will be next.
When done, board-dt.c will no longer be dreamplug specific, and dt's can
be made for the other kirkwood boards.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
Andrew Lunn
Jason Cooper
Thomas Petazzoni
Sebastian Hesselbarth
Linus Torvalds
Michael Walle
Jamie Lentin