aboutsummaryrefslogtreecommitdiffstats
path: root/arch/arm/boot/dts/sama5d4.dtsi (follow)
AgeCommit message (Collapse)AuthorFilesLines
2018-09-12ARM: dts: at91: sama5d4: add labels to soc dtsi for derivative boardsEugen Hristev1-4/+4
This adds labels to commonly used device-tree nodes so that derivative boards can avoid ahb/apb hierarchy. Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2018-06-20ARM: dts: fix PMC compatibleAlexandre Belloni1-1/+1
Make each SoC dtsi use its soc specific PMc compatible string. This solves a potential issue on at91sam9261 and at91sam9263 when using suspend to RAM Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2018-03-21ARM: dts: at91: fixes uart pinctrl, set pullup on rx, clear pullup on txPeter Rosin1-14/+14
Remove pullup on uart TX signals, they are push-pull outputs thus pullups are pointless. Add pullup on uart RX signals, they prevent the RX signals to be left floating and so consuming a useless extra amount of power in crowbarred state if nothing is connected to RX. Signed-off-by: Peter Rosin <peda@axentia.se> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2018-02-13ARM: dts: at91: sama5d4: fix pinctrl compatible stringSantiago Esteban1-1/+1
The compatible string is incorrect. Add atmel,sama5d3-pinctrl since it's the appropriate compatible string. Remove the atmel,at91rm9200-pinctrl compatible string, this fallback is useless, there are too many changes. Signed-off-by: Santiago Esteban <Santiago.Esteban@microchip.com> Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com> Cc: stable@vger.kernel.org #v3.18 Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2017-12-31ARM: dts: at91: sama5d4: Add TCB2Alexandre Belloni1-0/+10
The third TC block is missing from the dtsi. It has no output pins but can still be used for timers as the IRQ is wired. Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2017-12-31ARM: dts: at91: sama5d4: TC blocks are also simple-mfd and syscon devicesAlexandre Belloni1-2/+6
Add simple-mfd and syscon to the TC blocks to allow to register one of the channels as clocksource properly at boot time and free up the remaining channels for other use. Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2017-10-20arm: dts: fix unit-address leading 0sRob Herring1-5/+5
Fix dtc warnings for 'simple_bus_reg' due to leading 0s. Converted using the following command: perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find arch/arm/boot/dts -type -f -name '*.dts*' Dropped changes to ARM, Ltd. boards LED nodes and manually fixed up some occurrences of uppercase hex. Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2017-05-31ARM: dts: at91: Switch to the new NAND bindingsBoris Brezillon1-31/+0
Use the new EBI/NAND bindings to declare NAND chips and remove old NAND nodes along the way. Note that we keep using old bindings in at91rm9200.dtsi because this SoC is not supported by the EBI driver. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Tested-by: Peter Rosin <peda@axentia.se> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2017-05-31ARM: dts: at91: Declare EBI/NAND controllersBoris Brezillon1-0/+160
Declare new nodes for the EBI and NAND controllers embedded in various at91/sama5 SoCs. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2017-01-10ARM: dts: at91: sama5d4: change DMA allocation for secure peripheralsNicolas Ferre1-8/+8
Some peripherals are "Programmable Secure" but left as "Secure" by default. If tried to be connected to Non-Secure DMA controller, the possibility to leak secure data is prevented so using these peripherals with DMA1 is not possible with this default configuration (MATRIX_SPSELR registers setup by bootloader). Move them to DMA0 which is an "Always-Secure" DMA controller. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-11-07ARM: dts: at91: sama5d4: use proper sckc compatibleAlexandre Belloni1-23/+4
Now that there is support for the sama5d4 slow clock controller, use its driver. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-10-20ARM: dts: at91: fixes dbgu pinctrl, set pullup on rx, clear pullup on txSylvain Rochet1-2/+2
Remove pullup on dbgu DTXD signal, it is a push-pull output thus the pullup is pointless. Add pullup on dbgu DRXD signal, it prevents the DRXD signal to be left floating and so consuming a useless extra amount of power in crowbarred state if nothing is externally connected to dbgu. Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-07-15ARM: dts: at91: Fix USB endpoint nodesAlexandre Belloni1-16/+16
Endpoint nodes have a reg property. Add their mandatory unit-address. This solves: Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep0 has a reg or ranges property, but no unit name Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep1 has a reg or ranges property, but no unit name Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep2 has a reg or ranges property, but no unit name Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep3 has a reg or ranges property, but no unit name Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep4 has a reg or ranges property, but no unit name Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep5 has a reg or ranges property, but no unit name Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep6 has a reg or ranges property, but no unit name Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep7 has a reg or ranges property, but no unit name Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep8 has a reg or ranges property, but no unit name Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep9 has a reg or ranges property, but no unit name Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep10 has a reg or ranges property, but no unit name Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep11 has a reg or ranges property, but no unit name Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep12 has a reg or ranges property, but no unit name Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep13 has a reg or ranges property, but no unit name Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep14 has a reg or ranges property, but no unit name Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep15 has a reg or ranges property, but no unit name Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-07-15ARM: dts: at91: Fix ADC trigger nodesAlexandre Belloni1-4/+4
The triggers don't need a reg property, remove it when prenset. Also remove the unit-address from their name. This solves: Warning (unit_address_vs_reg): Node /ahb/apb/adc@fc034000/trigger@0 has a unit name, but no reg property Warning (unit_address_vs_reg): Node /ahb/apb/adc@fc034000/trigger@1 has a unit name, but no reg property Warning (unit_address_vs_reg): Node /ahb/apb/adc@fc034000/trigger@2 has a unit name, but no reg property Warning (unit_address_vs_reg): Node /ahb/apb/adc@fc034000/trigger@3 has a unit name, but no reg property Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2016-05-06ARM: dts: at91: sama5d4: add trng nodeMike Williams1-0/+7
Add node to support SAMA5D4 hardware random number generator. Signed-off-by: Mike Williams <mike@mikebwilliams.com> [nicolas.ferre@atmel.com: reduce the register map size] Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2016-04-27ARM: dts: at91: sama5d4: add watchdog interrupt propertyNicolas Ferre1-0/+1
The "interrupts" property is missing from the watchdog node. Add it with highest priority value of 7. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2016-01-27ARM: dts: at91: sama5d4: fix instance id of DBGUMohamed Jamsheeth Hajanajubudeen1-1/+1
Change instance id of DBGU to 45. Signed-off-by: Mohamed Jamsheeth Hajanajubudeen <mohamedjamsheeth.hajanajubudeen@atmel.com> Fixes: 7c661394c56c ("ARM: at91: dt: add device tree file for SAMA5D4 SoC") Cc: stable@vger.kernel.org # 3.18+ Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2015-12-15ARM: at91/dt: sama5d4: update i2c compatible stringLudovic Desroches1-3/+3
A new compatible string has been introduced: atmel,sama5d4-i2c. It allows to use the i2c-sda-hold-time-ns property if needed. Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2015-12-15ARM: at91/dt: sama5d4 master clock can run at 200MHz nowNicolas Ferre1-1/+1
After the change of frequency a SAMA5D4 can reach, we have to modify the maximum clock specification for the master clock, up to 200MHz now. It avoids the wrong message saying that "master clk is overclocked" for this configuration. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2015-12-15ARM: at91/dt: sama5d4: Add pinmux for 8-bit MMC0 busMarek Vasut1-0/+8
Add pinmux for the 4 remaining signals used in 8-bit MMC 0 bus configuration. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com> Reviewed-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2015-12-15ARM: at91/dt: sama5d4: Fix mmc0 pinmux commentsMarek Vasut1-5/+5
Synchronise the comments in mmc0 pinmux node with HSMCI0 pinmux description in the Atmel SAMA5D4 datasheet from 24-Aug-15 page 1119, section 37.6.1, Table 37-3 . Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com> Reviewed-by: Josh Wu <josh.wu@atmel.com> Reported-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2015-11-16ARM: at91/dt: sama5d4: change watchdog compatibleWenyou Yang1-1/+1
Change the watchdog compatible to "atmel,sama5d4-wdt" to support SAMA5D4 watchdog driver. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2015-10-19ARM: at91/dt: sama5d4: add the macb1 nodeGregory CLEMENT1-0/+30
The second macb is present on all the sama5d4 SoCs. Let's add a node reflecting it in the device tree. Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2015-10-19ARM: at91/dt: use syscon for PMCAlexandre Belloni1-1/+1
The PMC is not only used to drive the clocks but also has some registers related to other functions. One of those is for example the USB gadget bias. Using a syscon allows to properly separate those functions. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2015-09-18ARM: at91/dt: sama5d4: enable crypto nodesNicolas Ferre1-3/+3
The crypto modules will provide HW AES/TDES/SHA for any sama5d4 board. Enable them by default. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2015-09-18ARM: at91/dt: sama5d4: add pioD pin mux mask and enable pioDJosh Wu1-2/+1
Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2015-09-18ARM: at91/dt: corrections to i2c1 declaration to sama5d4Holger Busse1-4/+4
Correcting the dma declaration for i2c1 dma. Signed-off-by: Holger Busse <h.busse@kathrein-sachsen.de> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Fixes: 4cc7cdf35c5f ("ARM: at91/dt: add i2c1 declaration to sama5d4") Cc: stable@vger.kernel.org # v4.1+
2015-08-07ARM: at91/dt: sama5d4: use slow clock where necessaryAlexandre Belloni1-4/+8
The watchdog, the reset controller, the RTC, the shutdown controller, the timer counters and the LCD PWM need the slow clock, add it where necessary. Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
2015-07-30ARM: at91/dt: sama5: update rstc to correct compatible stringJosh Wu1-1/+1
They'll use "atmel,sama5d3-rstc" for reset function. Signed-off-by: Josh Wu <josh.wu@atmel.com> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> [nicolas.ferre@atmel.com: add the old compatible string as a fallback] Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2015-07-28ARM: at91/dt: sama5d4: move ADC pinctrl to board device treesAlexandre Belloni1-9/+0
The ADC pinctrl is board specific, move it to the board device trees. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2015-07-28ARM: at91/dt: sama5d4: fix external trigger propertyAlexandre Belloni1-1/+1
The property is actually atmel,adc-use-external-triggers. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2015-07-01ARM: at91/dt: update udc compatible stringsBoris Brezillon1-1/+1
at91sam9g45, at91sam9x5 and sama5 SoCs should not use "atmel,at91sam9rl-udc" for their USB device compatible property since this compatible is attached to a specific hardware bug fix. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Tested-by: Bo Shen <voice.shen@atmel.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: <stable@vger.kernel.org> #4.0+ Signed-off-by: Kevin Hilman <khilman@linaro.org>
2015-06-10ARM: at91/dt: sama5d4: fix dma conf for aes, sha and tdes nodesludovic.desroches@atmel.com1-10/+10
The xdmac channel configuration is done in one cell not two. This error prevents from probing devices correctly. Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> Fixes: 83906783b766 ("ARM: at91/dt: sama5d4: add aes, sha and tdes nodes") Cc: stable@vger.kernel.org # 4.1 Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Kevin Hilman <khilman@linaro.org>
2015-05-22ARM: at91/dt: remove useless usb clockBoris Brezillon1-3/+2
The ohci driver now calls clk_set_rate on the uhpck clock (which forwards set_rate requests to its parent: the usb clock). Remove useless references to usb clocks from ohci definitions. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2015-05-22ARM: at91/dt: remove useless uhpck clock references from ehci defintionsBoris Brezillon1-2/+2
The uhpck is useless for High-Speed communications, remove the reference to this clock in all ehci definitions. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2015-05-19ARM: at91/dt: sama5: reduce the NFC command register mapJosh Wu1-1/+1
commit 111573ccd89b ("mtd: atmel_nand: check NFC busy flag by HSMC_SR instead of NFC cmd regs") check NFC busy by nfc SR instead of NFC cmd regs. So we don't need to map NFC cmd registers to include NFCBUSY bit. That means we only need map 0x08000000 instead of 0x10000000 for NFC cmd regs. This patch reduce the NFC cmd regs map for sama5d3 & sama5d4. Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2015-05-19ARM: at91/dt: sama5d4: update pinctrl rangesLudovic Desroches1-1/+2
Update the pinctrl ranges property to support pioD controller whose mapping is not contiguous with other pio controllers. Without this update, getting resource will fail, then pinctrl probe will fail too because there is a missing pio controller. Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2015-05-19ARM: at91/dt: sama5d4: add spi1, spi2 dt nodesSuchang Ko1-0/+60
Add sama5d4 spi1, spi2 dt nodes & pinctrl. Signed-off-by: Suchang Ko <suchangko@samul.kr> [nicolas.ferre@atmel.com: split patch, reorder & whitespace fixes] Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2015-05-11ARM: at91/dt: sama5d4: add uart0, uart1 dt nodesSuchang Ko1-0/+56
Add sama5d4 uart0, uart1 dt nodes, pinctrl and related aliases. Signed-off-by: Suchang Ko <suchangko@samul.kr> [nicolas.ferre@atmel.com: split patch, reorder & whitespace fixes] Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2015-05-11ARM: at91/dt: sama5d4: add usart0, usart1 dt nodesJosh Wu1-0/+68
Also add the pinctrl for usart0, usart1. Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2015-04-22Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-socLinus Torvalds1-0/+342
Pull ARM DT updates from Olof Johansson: "As always, this tends to be one of our bigger branches. There are lots of updates this release, but not that many jumps out as something that needs more detailed coverage. Some of the highlights are: - DTs for the new Annapurna Labs Alpine platform - more graphics DT pieces falling into place on Exynos, bridges, clocks. - plenty of DT updates for Qualcomm platforms for various IP blocks - some churn on Tegra due to switch-over to tool-generated pinctrl data - misc fixes and updates for Atmel at91 platforms - various DT updates to add IP block support on Broadcom's Cygnus platforms - more updates for Renesas platforms as DT support is added for various IP blocks (IPMMU, display, audio, etc)" * tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (231 commits) ARM: dts: alpine: add internal pci Revert "ARM: dts: mt8135: Add pinctrl/GPIO/EINT node for mt8135." ARM: mvebu: use 0xf1000000 as internal registers on Armada 370 DB ARM: dts: qcom: Add idle state device nodes for 8064 ARM: dts: qcom: Add idle states device nodes for 8084 ARM: dts: qcom: Add idle states device nodes for 8974/8074 ARM: dts: qcom: Update power-controller device node for 8064 Krait CPUs ARM: dts: qcom: Add power-controller device node for 8084 Krait CPUs ARM: dts: qcom: Add power-controller device node for 8074 Krait CPUs devicetree: bindings: Document qcom,idle-states devicetree: bindings: Update qcom,saw2 node bindings dt-bindings: Add #defines for MSM8916 clocks and resets arm: dts: qcom: Add LPASS Audio HW to IPQ8064 device tree arm: dts: qcom: Add APQ8084 chipset SPMI PMIC's nodes arm: dts: qcom: Add 8x74 chipset SPMI PMIC's nodes arm: dts: qcom: Add SPMI PMIC Arbiter nodes for APQ8084 and MSM8974 arm: dts: qcom: Add LCC nodes arm: dts: qcom: Add TCSR support for MSM8960 arm: dts: qcom: Add TCSR support for MSM8660 arm: dts: qcom: Add TCSR support for IPQ8064 ...
2015-04-03Merge tag 'omap-for-v4.1/wl12xx-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dtOlof Johansson1-4/+4
Merge "wireless wl12xx and omap device tree changes for v4.1" from Tony Lindgren: Wireless and omap changes to make wl12xx driver to use device tree data instead of platform data from Eliad Peller <eliad@wizery.com>: - Add device-tree support to the wlcore (wl12xx/wl18xx) driver. - Update the current users to use the bindings instead of pdata-quirks. - Finally, remove the deprecated wl12xx_platform_data struct Note that da850 board file code that still uses the platform data, but we have da850.dtsi that can be used instead. So it was decided that we should try to remove the wl12xx support from the da850 board file as suggested by Sekhar Nori <nsekhar@ti.com>. As it's the last patch in the series, the last patch can be simply reverted if needed. As this series touches quite a bit of arch code, it was suggested by Kalle Valo <kvalo@codeaurora.org> that the whole series should be merged via the arm-soc tree. * tag 'omap-for-v4.1/wl12xx-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: wlcore: remove wl12xx_platform_data ARM: dts: add wl12xx/wl18xx bindings wlcore: add device-tree support dt: bindings: add TI's wilink wireless device wl12xx: use frequency instead of enumerations for pdata clocks wlcore: set irq_trigger in board files instead of hiding behind a quirk + Linux 4.0-rc4 Signed-off-by: Olof Johansson <olof@lixom.net>
2015-03-23ARM: at91/dt: sama5d4: add rgb777 LCD line configurationNicolas Ferre1-1/+28
For the SAMA5D4 SoC, some LCD lines are in conflict with useful peripherals. Remove these lines and the lowest significant bit of a 24 bit LCD. It gives us a RGB 777 configuration. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2015-03-23ARM: at91/dt: sama5d4: fix LCD pins for RGB666 formatNicolas Ferre1-7/+7
The color arrangement for SAMA5D4 in RGB 666 takes the most significant bits of each color line groups. Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2015-03-23ARM: at91/dt: sama5d4: add hlcdc nodeBoris Brezillon1-0/+28
Add HLCDC node. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2015-03-23ARM: at91/dt: sama5d4: add lcdc pin definitionsBoris Brezillon1-0/+95
Add LCDC pin definitions. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2015-03-13ARM: at91/dt: introduce atmel,<chip>-dbguAlexandre Belloni1-1/+1
The DBGU is not a simple UART and we need to be able to distinguish it from the other UARTs, in particular to get its address and check the chip id. Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2015-03-11ARM: at91/dt: fix USB high-speed clock to select UTMINicolas Ferre1-1/+1
The UTMI clock must be selected by any high-speed USB IP. The logic behind it needs this particular clock. So, correct the clock in the device tree files affected. Reported-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Cc: <stable@vger.kernel.org> #3.18
2015-03-05ARM: at91/dt: sama5d4: fix lcdck clock definitionBoris BREZILLON1-2/+2
lcdck takes mck (not smd) as its parent. It is also assigned id 3 and not 4. Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com> [nicolas.ferre@atmel.com: squashed 2 related patches] Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2015-03-05ARM: at91/dt: sama5d4: rename lcd_clk into lcdc_clkBoris BREZILLON1-1/+1
Rename lcd_clk into lcdc_clk to be consistent with sama5d3 clock definitions. Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.