| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Since commit d7c5f6863550 ("ARM: dts: sun8i: a83t: bananapi-m3: Add
AXP813 regulator nodes") my BPIM3 no longer works at gigabit speed.
With the default setting, dldo3 is regulated at 2.9v which seems
sufficient for the PHY but the aforementioned commit drops it to 2.5V
which is insufficient. Note that this behaviour is random for all BPIM3.
Some work with 2.5V, but some don't.
Finnaly, someone from Bananapi confirmed that this regulator must be set
to 3.3V.
Fixes: d7c5f6863550 ("ARM: dts: sun8i: a83t: bananapi-m3: Add AXP813
regulator nodes")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
[wens@csie.org: Reworked commit message]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The Bananapi M3 has an onboard IR receiver.
This enables the onboard IR receiver subnode.
Unlike the other IR receivers this one needs a base clock frequency
of 3000000 Hz (3 MHz), to be able to work.
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The OPPs for the A83T CPU cores were added in v4.17 in commit 2db639d8c166
("ARM: dts: sun8i: a83t: add stable OPP tables and CPUfreq"), but board
level regulator supplies for the CPU clusters were only added for the
TBS-A711 tablet. This means the other A83T boards do not benefit from
voltage scaling, or worse, if the implementation does not scale the
frequency when the voltage is fixed, no benefit at all.
Add board level CPU cluster power supplies to all the A83T development
boards, so they can have proper dynamic CPU voltage and frequency scaling.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Pull "Allwinner H3/H5 changes for 4.17" from Maxime Ripard:
Here is our usual bunch of changes to the common DTSI shared between arm
and arm64, and their associated device trees.
Even though the diffstat is quite big, it's been mostly just cleanups. The
big feature is that the HDMI is now suported on H3 and H5 boards.
* tag 'sunxi-h3-h5-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: allwinner: H5: Add Xunlong Orange Pi Zero Plus
ARM: dts: sun8i-h3: Add Mali node
ARM64: dts: sun50i: h5: Enable HDMI output on H5 boards
ARM: dts: sun8i: h3: Enable HDMI output on H3 boards
ARM: dts: sunxi: h3/h5: Add HDMI pipeline
ARM: dts: sun8i: h2-plus: remove unnecessary mmc1_pins node
ARM: dts: sunxi: h3-h5: rename mmc0_pins_a and mmc1_pins_a
ARM: dts: sunxi: h3-h5: Move pinctrl of mmc1 from dts to dtsi
ARM: dts: sunxi: h3-h5: Move pinctrl of mmc0 from dts to dtsi
ARM: dts: sunxi: h3-h5: remove mmc0 card detection pin from pinctrl
ARM: dts: sun8i: h2+: add support for Banana Pi M2 Zero board
ARM: dts: sunxi: Switch MMC nodes away from cd-inverted property
ARM: dts: nanopi-neo-air: Add WiFi / eMMC
|
|
BananaPi M3 includes HDMI connector, so add support for it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The Bananapi M3 has two controllable LEDs, blue and green, that are tied
to the PMIC's two GPIO pins.
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
Using the cd-inverted property is not useful when GPIOs are used as card
detects since the polarity can be specified with the usual
GPIO_ACTIVE_(HIGH|LOW) GPIO flags. It has also caused confusion for
U-Boot developers, so migrate all sunxi boards away from cd-inverted.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The Cubietruck Plus has a Realtek RTL8211E RGMII PHY tied to the EMAC.
The AXP818 PMIC's regulators provide main power and secondary signaling
voltages to the PHY. The latter is always on, as it also supplies the
pingroup on the SoC, which has other uses.
The Bananapi M3 has a Realtek RTL8211E RGMII PHY tied to the EMAC.
The AXP818 PMIC's SW regulators provides power to the PHY.
This patch enables Ethernet with the EMAC on both these boards by
enabling the emac node and setting all the required properties.
A proper ethernet alias is added as well.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The WiFi side of the AP6212 WiFi/BT combo module is connected to
mmc1. There are also GPIOs for enable and interrupts. An external
clock from the AC100 RTC is also used.
Enable WiFi on this board by enabling mmc1 and adding the power
sequencing clocks and GPIO, as well as the chip's interrupt line.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This patch adds device nodes for all the regulators of the AXP813 PMIC.
Sunxi common regulators are removed, and USB VBUS regulators are added.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The BPI-M3 is an Allwinner A83T based SBC in the Bananapi/Bpi family.
It is roughly the same form factor as the BPI-M1+, with roughly the
same peripherals and connectors:
- 2GB LPDDR3 DRAM
- 8GB eMMC
- Micro-SD card slot
- HDMI output
- Headset (stereo + mic) jack
- Onboard mic
- Gigabit Ethernet with RTL8211E transceiver
- Ampak AP6212 WiFi + BT
- USB OTG connector
- USB-to-SATA bridge connected through a USB 2.0 hub
- Consumer IR receiver
- MIPI DSI LCD panel connector
- Camera interface (parallel and MIPI CSI) connector
- 3 LEDs (Red, Green, Blue), of which 2 are controllable (GB)
- Raspberry Pi 2 compatible GPIO header
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
Corentin Labbe
Philipp Rossak
Chen-Yu Tsai
Arnd Bergmann
Jernej Skrabec
Tuomas Tynkkynen