| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Neither the OHCI or EHCI bindings are using the phy-names property, so we
can just drop it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
I2C2 is available on the PE pingroup, on the same pins as the camera
sensor interface (CSI) controller's camera control interface pins.
This provides an option to use I2C2 instead of that control interface
to configure camera sensors.
Add a pinctrl node for it. The property /omit-if-no-ref/ is added to
keep the device tree blob size down if it is unused.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Allwinner A83T SoC has a low res adc like the one in Allwinner A10 SoC.
Now the driver has been modified to support it.
Add support for it.
Signed-off-by: Ziping Chen <techping.chan@gmail.com>
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
A83T DTSI has cpu clocks defined only on the first CPU in each cluster.
We can bring down any CPU in the cluster, so we need to define clock
for each CPU, so that the system knows what clock to use if the first
CPU is down.
Also move the clocks property below the compatible on cpus where it is
already defined. Property "clock-names" is not needed.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Add pin definitions for UART2 PB pins. These are used on TBS-A711
tablet.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Enable to use CPUs as cooling device in the future, by adding
"#cooling-cells" to each CPU node. This property should be present for
all the CPUs of a cluster. If these are present only for a subset of
CPUs of a cluster then things will start falling apart as soon as the
CPUs are brought online in a different order. For example, this will
happen because the operating system looks for such properties in the CPU
node it is trying to bring up, so that it can register a cooling device.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
A83T has 5 UART interfaces, but only the first two have their nodes
defined in sun8i-a83t.dtsi. Add nodes for the missing interfaces.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The USB OTG binding we have mandates to have a dr_mode property, yet not
all boards are setting it.
Since the generic otg binding states that the default mode should be the
OTG mode, let's use that one in our DTSI.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Even though we shouldn't really have any external user of the clock
provided by the TCON, if clock-output-names is set, then #clock-cells must
be there as well.
Fix this.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
As can be shown by the YAML schema now, the combination of GIC compatibles
we were using has never been an option.
Switch to the gic-400 variant, which is the more correct option.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Our display engine endpoints trigger some DTC warnings due to the fact that
we're having a single endpoint that doesn't need any reg property, and
since we don't have a reg property, we don't need the address-cells and
size-cells properties anymore.
Fix those
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Unlike what the binding for multiple pipeline documents, the A83t doesn't
have the cross links between the TCON and the mixers.
Let's add them.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Our memory node will generate a warning in DTC since the unit address is
not matching the reg property. However, that node will be created by the
bootloader, so we can just remove it entirely in order to remove that
warning.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The cir interface is like on the H3 located at 0x01f02000 and is exactly
the same. This patch adds support for the ir interface on the A83T.
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The CIR Pin of the A83T is located at PL12.
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
ddress-cells/size-cells is unnecessary for dwmac-sun8i node.
It was in early days, but since a mdio node is used, it could be
removed.
This patch fix the following DT warning:
Warning (avoid_unnecessary_addr_size): /soc/ethernet@1c50000: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Add the use of enable-method property for SMP support which allows
to handle the SMP support for this specific SoC.
This commit adds enable-method properties to all CPU nodes.
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Add CCI-400 node and control-port on CPUs needed by SMP bringup.
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The R_CPUCFG is a collection of registers needed for SMP bringup
on clusters and cluster's reset.
For the moment, documentation about this register is found in
Allwinner's code only.
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
As we found in sun9i-a80, CPUCFG is a collection of registers that are
mapped to the SoC's signals from each individual processor core and
associated peripherals.
These registers are used for SMP bringup and CPU hotplugging.
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Allwinner a83t has a 1 KB sid block with efuse for security rootkey and thermal
calibration data, add node to describe it.
a83t-sid is not currently supported by nvmem/sunxi-sid, but it is
supported in an external driver for FreeBSD.
Signed-off-by: Kyle Evans <kevans@FreeBSD.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The Allwinner A83T is an octacore A7 divided in two clusters of 4 A7,
each cluster having its own regulator and clock.
The operating points were found in Allwinner BSP and fex files.
Note that there are a few OPPs that are missing:
1608000000Hz with 920000mV
1800000000Hz with 1000000mV
2016000000Hz with 1080000mV
These OPPs are pretty unstable but it might be due to the SoC quickly
overheating (till the board completely shuts down).
It seems impossible to reach those frequencies with none or passive
cooling, so better leave them out by default.
It's still possible to add those OPPs on a per-board basis though.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
[maxime: Reordered the nodes alphabetically]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The Allwinner A83T is a SoC with two clusters of 4 A7, each cluster
having its own regulator and clock.
The regulators are board-specific, thus we need labels for cpu0 and
cpu100 so that we can use references to these nodes from the board
header file.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
This commit adds all bits necessary for HDMI on A83T - mixer1, tcon1,
hdmi, hdmi phy and hdmi pinctrl entries.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The A83T has an LVDS bus that can be connected to a panel or a bridge. Add
the pinctrl group for it.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The A83T has the same PWM block than the H3. Add it to our DT.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The display pipeline on the A83T is mainly composed of the mixers and
TCONs, plus various encoders.
Let's add the first mixer and TCON to the DTSI since the only board I have
can use only the LVDS output on the first TCON. The other parts will be
added eventually.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The A83T has 3 I2C controllers under the standard bus. There is one
more in the R_ block section. The pin functions for the 3 controllers
are on PH 0~6. I2C2 can also be used on pins PE14 and PE15, but these
pins can also mux the CSI (camera sensor interface) controller's
embedded I2C controller. The latter seems to be preferred in the
reference designs for I2C camera sensor access, freeing I2C2 for other
uses.
This patch adds device nodes for the three standard I2C controllers,
as well as pinmux settings for the PH pins. For I2C0 and I2C1, since
they only have one possible setting, just set them by default.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The A83T has 3 I2S controllers. The first is multiplexed with the TDM
controller. The pins are generally connected to the codec side of the
AXP81x PMIC/codec/RTC chip. The second is free for other uses. The
third only supports output, and is connected internally to the HDMI
controller for HDMI audio output.
This patch adds device nodes for the controllers, and a default pinmux
setting for the second controller.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The dwmac-sun8i is an ethernet MAC hardware that support 10/100/1000 speed.
This patch add support for it on the Allwinner a83t SoC Device-tree.
This patch add the emac device node and the related RGMII pins node.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
mmc1 only has 1 possible pinmux setting.
Move any settings to the dtsi file and set it by default.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This patch remove leading 0 of unit address and so remove
lots of warning when building DT with W=1.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The A83T has an UART1 controller, with the RTS and CTS pins routed so it
can be used for devices with hardware flow control, like a bluetooth chip.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Add the pinctrl definitions for the A83t MMC1 controller.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Those nodes are useless, remove them.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The USB OTG controller found on the A83T is compatible with the one
found on the A33.
Add a device node for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The A83T has 3 USB PHYs, 1 for USB OTG, 1 for standard USB 2.0, 1 for
USB HSIC. EHCI0/OHCI0 are the standard USB host pair, while EHCI1 is
the host controller for HSIC. OTG is not added yet.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The A83T has an RSB controller for talking to the PMIC and audio codec.
Add a device node for it. Since there is only one usable pinmux setting,
for it, add that as well.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
mmc2 can support 8-bit eMMC chips, with a dedicated reset line.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The A83T has 3 MMC controllers. The third one is a bit special, as it
supports a wider 8-bit bus, and a "new timing mode".
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The R_INTC interrupt controller handles the NMI interrupt pin for the
SoC. While there is no documentation or code from the vendor for this
device on the A83T, existing mainline kernel drivers and bindings show
this to be similar to the old Allwinner interrupt controller found on
the A10 SoC, but with only the NMI interrupt wired. Register poking
experiments confirm this.
The device seems to be the same across all recent Allwinner SoCs, apart
from the A20 and A80, which have a separate set of registers to handle
the NMI interrupt. We already have a set of bindings supporting this
on the A31.
Add a device node for it, with an SoC specific compatible.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Now that the CCU device tree binding headers have been merged, we can
use the properly named macros in the device tree, instead of raw
numbers.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This patch add the dt node for the syscon register present on the
Allwinner A83T
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The A83T has 1 pingroup with 13 pins belonging to the R_PIO
or special pin controller.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The A83T's PRCM has the same set of clocks and resets as the A64.
However, a few dividers are different. And due to the lack of a low
speed 32.768 kHz oscillator, a few of the clock parents are different.
The PRCM also has controls for various power domains. These are not
supported yet, neither in software nor in the device tree binding.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The A83T SoC has an SPDIF transmitter block. According to the vendor
BSP kernel, it is compatible with the one found on the H3 SoC.
Add a device node and pinmux setting for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The A83T SoC has a DMA controller that supports 8 DMA channels
to and from various peripherals.
Add a device node for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The datasheets for Allwinner SoCs set strict requirements on the
stability of the external crystal oscillators. Add the accuracy
for the main 24MHz oscillator to the device tree.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Now that we have support for the A83T CCU, add a device node for it,
and replace any existing placeholder clock phandles with the correct
ones.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
We should use hyphens and not underscores in device node names.
Replace the ones that were just added.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
Maxime Ripard
Chen-Yu Tsai
Ziping Chen
Ondrej Jirman
Philipp Rossak
Corentin Labbe
Mylène Josserand
kevans@FreeBSD.org
Quentin Schulz
Jernej Skrabec
Maxime Ripard
Corentin LABBE