| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
So far we've enabled pull-up and pull-down resistors on GPIOs using a
pinctrl node. Now that the GPIO binding allows for a flag to declare this,
let's switch to it.
This brings us closer to removing all the GPIO pinctrl nodes, which will in
turn allow us to switch the pinctrl strict mode on.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The I2C's and MMC0 controllers have only one muxing option in the SoC. In
such a case, we can just move the muxing into the DTSI, and remove it from
the DTS.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Some GPIO pinctrl nodes cannot be easily removed, because they would also
change the pin configuration, for example to add a pull resistor or change
the current delivered by the pin.
Those nodes still have underscores and unit-addresses in their node names
in our DTs, so adjust their name to remove the warnings. Use that occasion
to also fix some poorly chosen node-names.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
All our pinctrl nodes were using a node name convention with a unit-address
to differentiate the different muxing options. However, since those nodes
didn't have a reg property, they were generating warnings in DTC.
In order to accomodate for this, convert the old nodes to the syntax we've
been using for the new SoCs, including removing the letter suffix of the
node labels to the bank of those pins to make things more readable.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Boards usually have an external pull-up on the card-detect signal, so
there's no need to add another one.
This also removes a DTC warning.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
One of the usage of the LRADC is to implement buttons. The bindings define
that we should have one subnode per button, with their associated voltage
as a property.
However, there was no reg property but we still used the voltage associated
to the button as the unit-address, which eventually generated warnings in
DTC.
Rename the node names to avoid those warnings.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
The gpio pinctrl nodes are redundant and as such useless most of the times.
Since they will also generate warnings in DTC, we can simply remove most of
them.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Some boards override the MMC pin muxing settings in order to enable the
pull-ups and change the drive strength to a value higher than the default.
While this was needed in the earlier days, this is now the default setting
for those pins, and therefore we don't need those board-specific settings
anymore.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
|
|
Enable the audio codec and the audio dai for the sun8i R16 Parrot board.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Previously, the Allwinner Parrot R16 used everything declared in AXP221
DTSI while it has an AXP223 PMIC.
This corrects that so the Allwinner Parrot R16 can get some features the
AXP223 has (at the moment, ability to have 100mA as maximal current on
VBUS power supply).
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Now that we can handle the generic pinctrl bindings, convert our DT to it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The allwinner,pull property set to NO_PULL was really considered our
default (and wasn't even changing the default value in the code).
Remove these properties to make it obvious that we do not set anything in
such a case.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The allwinner,drive property set to 10mA was really considered as our
default. Remove all those properties entirely to make that obvious.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Parrot Board is an evaluation board with an Allwinner R16 (assumed
to be close to an Allwinner A33), 4GB of eMMC, 512MB of RAM, USB host
and OTG, a WiFi/Bluetooth combo chip, a micro SD Card reader, 2
controllable buttons, an LVDS port with separated backlight and
capacitive touch panel ports, an audio/microphone jack, a camera CSI
port, 2 sets of 22 GPIOs and an accelerometer.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
Maxime Ripard
Mylène Josserand
Quentin Schulz
Maxime Ripard