| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The ARM GIC only supports interrupts with either level-high or
rising-edge types for SPIs. The interrupt type for the Palmas PMIC used
for Tegra114 boards is specified as level-low which is invalid for the
GIC. This has gone undetected because until recently, failures to set
the interrupt type when the interrupts are mapped via firmware (such as
device-tree) have not been reported. Since commits 4b357daed698
("genirq: Look-up trigger type if not specified by caller") and
1e2a7d78499e ("irqdomain: Don't set type when mapping an IRQ"), failure
to set the interrupt type will cause the requesting of the interrupt to
fail and exposing incorrectly configured interrupts.
Please note that although the interrupt type was never being set for the
Palmas PMIC, it was still working fine, because the default type setting
for the interrupt, 'level-high', happen to match the correct type for
the interrupt.
Finally, it should be noted that the Palmas interrupt from the PMIC is
actually 'level-low', however, this interrupt signal is inverted by the
Tegra PMC and so the GIC actually sees a 'level-high' interrupt which is
what should be specified in the device-tree interrupt specifier.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This seems to have been copied and pasted since the beginning of time,
though only until Tegra124, likely because that DT was written from
scratch or it was fixed along the way.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add unit-addresses to nodes that have a reg property to avoid warnings
on newer versions of DTC.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Though the keyboard and other driver will continue to support the legacy
"gpio-key,wakeup", "nvidia,wakeup-source" boolean property to enable the
wakeup source, "wakeup-source" is the new standard binding.
This patch replaces all the legacy wakeup properties with the unified
"wakeup-source" property in order to avoid any further copy-paste
duplication.
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
vddio_sdmmc3 is a vdd_io, and thus should be under the vqmmc-supply
property, not vmmc-supply.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This property was wrong and broke eMMC since commit 52221610d ("mmc:
sdhci: Improve external VDD regulator support"). Align the eMMC
properties to those of other Tegra boards.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
There are general changes pending to make the /aliases/serial* entries
number the serial ports on the system. On Tegra, so far the ports have
been just numbered dynamically as they are configured so that makes them
change.
To avoid this, add specific aliases per board to keep the old numbers.
This allows us to change the numbering by default on future SoCs while
keeping the numbering on existing boards.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Tegra DSI support has been fixed to support continuous clock behavior that
the panel used on SHIELD requires, so finally add its device tree node
since it is functional.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Input had been disabled by mistake on these pins, leading to issues with
SDIO devices like the Wifi module not being probed or random errors
occuring on the SD card.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
The pinmux subsystem complained that the nvidia,low-power-mode property
is not supported by the sdio1, sdio3 and gma drive groups. In addition
gma also does not support nvidia,drive-type. Remove these properties so
the pinmux configuration can properly be applied.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
NVIDIA SHIELD is a portable Android console containing a Tegra 4 SoC with
2GB RAM and a 720p panel.
The following hardware is enabled by this device tree: UART, eMMC, USB
(needs external power), PMIC, backlight, joystick, SD card, GPIO keys.
DSI panel, HDMI output, charger, self-powered USB, audio, wifi bluetooth
are not supported yet but might be by future patches (likely in that
order).
Touch panel and sensors will probably never be supported.
Initrd addresses are hardcoded to match the static values used by the
bootloader, since it won't add them for us. All the same, a kernel
command-line is provided to replace the one passed by the
bootloader which is filled with garbage.
NVIDIA SHIELD is typically booted with an appended DTB to avoid
modifications made by the bootloader.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
[swarren, fixed gpio-keys child node sort order, patch description]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
Jon Hunter
Thierry Reding
Sudeep Holla
Alexandre Courbot
Olof Johansson