| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
With commit d8e8fd0ebf8b ("mtd: rawnand: denali: decouple controller
and NAND chips"), the Denali NAND controller driver migrated to the
new controller/chip representation.
Update DT for it.
In the new binding, the number of connected chips are described in
DT instead of run-time probed.
I added just one chip to the reference boards, where we do not know
if the on-board NAND device is a single chip or multiple chips.
If we added too many chips into DT, it would end up with the timeout
error in nand_scan_ident().
I changed all the pinctrl properties to use the single CS.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Each CPU can (and does) participate in cooling down the system but the
DT only captures a handful of them, normally CPU0, in the cooling maps.
Things work by chance currently as under normal circumstances its the
first CPU of each cluster which is used by the operating systems to
probe the cooling devices. But as soon as this CPU ordering changes and
any other CPU is used to bring up the cooling device, we will start
seeing failures.
Also the DT is rather incomplete when we list only one CPU in the
cooling maps, as the hardware doesn't have any such limitations.
Update cooling maps to include all devices affected by individual trip
points.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add USB3 controller nodes including usb-core, resets, regulator, ss-phy
and hs-phy. This supports for Pro4, PXs2 and the boards.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add SD controller nodes for LD4, Pro4, sLD8, Pro5, and PXs2.
This is also used as an eMMC controller for LD4, Pro4, and sLD8.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add nodes of SPI controller for LD4, Pro4, sLD8, Pro5 and PXs2.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Catch up with the new binding of the Denali IP where three clocks,
"nand", "nand_x", "ecc" are required.
For UniPhier SoCs, the "nand_x" and "ecc" are tied up because they
are both 200MHz.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add syscon-phy-mode property specifying a phandle of system controller
to each ethernet node.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The GIO clock/reset, Another MAC clock, and the PHY clock are required
for the ethernet of Pro4 SoC.
And add clock-names and reset-names to the ethernet node of PXs2 since
we need to distinguish clocks and resets now.
Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This patch adds syscon property for specifying soc-glue core into
device-tree of PXs2 SoC.
Currently, soc-glue core is used for changing the state of S/PDIF
signal output pin to signal output state or Hi-Z state.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This patch adds audio controller, external codec and simple card node
of UniPhier AIO sound system for PXs2 SoCs.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
According to Documentation/process/license-rules.rst, move the SPDX
License Identifier to the very top of the file. I used C++ comment
style not only for the SPDX line but for the entire block because
this seems Linus' preference [1]. I also dropped the parentheses to
follow the examples in that document.
[1] https://lkml.org/lkml/2017/11/25/133
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add nodes of the AVE ethernet controller for Pro4, PXs2, LD6b SoCs
and the boards.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add efuse node for UniPhier LD4, Pro4, sLD8, Pro5 and PXs2.
This efuse node is included in soc-glue.
Signed-off-by: Keiji Hayashibara <hayashibara.keiji@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The dt-bindings header was applied to the driver subsystem. I had to
wait for a merge window to use it from DT.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add resets properties to all nodes that have reset lines.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The GPIO controller also acts as an interrupt controller and the
interrupt lines are connected to the AIDET block.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Fix warnings like follows:
Warning (node_name_chars_strict): Character '_' not recommended in ...
Commit 8654cb8d0371 ("dtc: update warning settings for new bus and
node/property name checks") says these checks are a bit subjective,
but Rob also says to not add new W=2 warnings.
The exising warnings should be fixed in order to catch new ones
easily.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add nodes of thermal monitor and thermal zone for UniPhier PXs2 SoC.
The thermal monitor node is included in sysctrl. Since the efuse might not
have a calibrated value of thermal monitor, this patch gives the default
value for PXs2.
Furthermore, add cpuN labels for reference in cooling-device property.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
All registers are located within 0x400 size from the base address.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add UniPhier AIDET (ARM Interrupt Detector) nodes to support
active low interrupts.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add NAND controller node to LD4, Pro4, sLD8, Pro5, and PXs2.
Set up pinctrl to enable 2 chip select lines except Pro4. The CS1
for Pro4 is multiplexed with other peripherals such as UART2, so
I did not enable it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
To include dt-bindings headers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Follow the recent trend for the license description, and fix the wrongly
stated X11 to MIT.
The X11 license text [1] is explicitly for the X Consortium and has a
couple of extra clauses. The MIT license text [2] is actually what the
current DT files claim.
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Compiling the UniPhier DT files with W=1, DTC warns like follows:
Warning (simple_bus_reg): Node /soc/system-bus@58c00000/support_card@1,1f00000/ethernet@00000000 simple-bus unit address format error, expected "0"
Warning (simple_bus_reg): Node /soc/system-bus@58c00000/support_card@1,1f00000/uart@000b0000 simple-bus unit address format error, expected "b0000"
Warning (simple_bus_reg): Node /soc/smpctrl@59800000 simple-bus unit address format error, expected "59801000"
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Compiling the DT file with W=1, DTC warns like follows:
Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 has a
unit name, but no reg property
Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Commit 9c0da3cc61f1 ("ARM: dts: explicitly mark skeleton.dtsi as
deprecated") declared that skeleton.dtsi was deprecated.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
I notice some mistakes in the SoC DTSI; wrong interrupts properties
of timer nodes, mismatch between the node name and the compatible
for sdctrl block. Given those problems fixed, the common parts
among SoCs are less than I had first expected. The more and more
property overrides are making the SoC DTSI unreadable.
Stretch out the SoC DTSI files and fix the following:
- Fix the 3rd cell of the interrupts property of the timer nodes
for Pro4, Pro5, PXs2
- Fix the node name mioctrl to sdctrl for Pro5, PXs2
- Fix the second region of l2 node for PXs2
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add a CPU clock to every CPU node and a CPU OPP table to use the
generic cpufreq driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
I made a mistake bacuse the Media I/O block is not implemented in
these SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The UniPhier reset controller driver has been merged. Enable it.
Also, replace the fixed-rate clocks with the dedicated clock
drivers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Use PSCI for enable-method instead of SoC specific implementation.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
All UniPhier device trees have the common prefix "uniphier-", so
"ph1-" is just making names longer. Recent documents and other
projects are not using PH1- prefixes any more.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
Masahiro Yamada
Viresh Kumar
Kunihiko Hayashi
Katsuhiro Suzuki
Keiji Hayashibara