| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This reverts commit ddb56254ae52acff7bd7fbd8f963e79bffc324d4. The EMAC
bindings have not stabilized yet, so we can't commit to keeping them
stable.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The BPI-M3 is an Allwinner A83T based SBC in the Bananapi/Bpi family.
It is roughly the same form factor as the BPI-M1+, with roughly the
same peripherals and connectors:
- 2GB LPDDR3 DRAM
- 8GB eMMC
- Micro-SD card slot
- HDMI output
- Headset (stereo + mic) jack
- Onboard mic
- Gigabit Ethernet with RTL8211E transceiver
- Ampak AP6212 WiFi + BT
- USB OTG connector
- USB-to-SATA bridge connected through a USB 2.0 hub
- Consumer IR receiver
- MIPI DSI LCD panel connector
- Camera interface (parallel and MIPI CSI) connector
- 3 LEDs (Red, Green, Blue), of which 2 are controllable (GB)
- Raspberry Pi 2 compatible GPIO header
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The h8homlet board has the A83T's standard USB 1.1/2.0 host pair routed
to a USB host port on the board. The other USB host port is routed to
USB OTG controller.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The Cubietruck-plus has a GL830 USB-to-SATA bridge connected to EHCI0,
and a USB3503 HSIC USB 2.0 hub connected to EHCI1. The USB3503's I2C
control interface is not connected.
This patch enables both EHCI controllers, adds a device node for the
USB hub, and includes sunxi-common-regulators.dtsi for the VBUS
regulators. The existing reg_vcc3v3 is dropped as it is also available
in the set of common regulators. Other unused regulators are disabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The USB OTG controller found on the A83T is compatible with the one
found on the A33.
Add a device node for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The A83T has 3 USB PHYs, 1 for USB OTG, 1 for standard USB 2.0, 1 for
USB HSIC. EHCI0/OHCI0 are the standard USB host pair, while EHCI1 is
the host controller for HSIC. OTG is not added yet.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The AXP813/AXP818 PMICs used with the A83T/H8 SoCs are actually 2 dies
in one package sharing the serial bus (I2C/RSB) pins. One die is the
actual PMIC. The other is an AC100 codec / RTC combo chip.
This patch adds the device nodes for the AC100 chip to the h8homlet-v2
device tree.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The AXP813/AXP818 PMICs used with the A83T/H8 SoCs are actually 2 dies
in one package sharing the serial bus (I2C/RSB) pins. One die is the
actual PMIC. The other is an AC100 codec / RTC combo chip.
This patch enables the RSB controller and adds a device node for the
PMIC die to the h8homlet-v2 device tree. Since the AXP813 and AXP818
are virtually identical, this patch uses the compatible string for
the former as a fallback.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The AXP813/AXP818 PMICs used with the A83T/H8 SoCs are actually 2 dies
in one package sharing the serial bus (I2C/RSB) pins. One die is the
actual PMIC. The other is an AC100 codec / RTC combo chip.
This patch adds the device nodes for the AC100 chip to the Cubietruck
Plus device tree.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The AXP813/AXP818 PMICs used with the A83T/H8 SoCs are actually 2 dies
in one package sharing the serial bus (I2C/RSB) pins. One die is the
actual PMIC. The other is an AC100 codec / RTC combo chip.
This patch enables the RSB controller and adds a device node for the
PMIC die to the Cubietruck Plus device tree. Since the AXP813 and
AXP818 are virtually identical, this patch uses the compatible string
for the former as a fallback.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The A83T has an RSB controller for talking to the PMIC and audio codec.
Add a device node for it. Since there is only one usable pinmux setting,
for it, add that as well.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The H8 homlet has a micro-SD card slot connected to mmc0,
and onboard eMMC from FORESEE, connected to mmc2.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Now that we support the MMC controllers on the A83T SoC, we can enable
them on some boards.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
mmc2 can support 8-bit eMMC chips, with a dedicated reset line.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The A83T has 3 MMC controllers. The third one is a bit special, as it
supports a wider 8-bit bus, and a "new timing mode".
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The dwmac-sun8i hardware is present on the Beelink X2.
It uses the internal PHY.
This patch create the needed emac node.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[wens@csie.org: Fixed typo in commit subject]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
This STB has a type A socket which acts as OTG.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The Bananapi M2-Magic is a board with an A33, a USB host and USB OTG
connectors, and 8GB eMMC, an AP6212 WiFi/Bluetooth chip and connectors for
DSI, CSI and GPIOs.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[wens@csie.org: Correct subject prefix case]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The Cubietruck has an AXP209 PMIC with battery connector.
This enables the battery power supply subnode.
Signed-off-by: Alexander Syring <alex@asyring.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[wens@csie.org: Correct subject prefix order]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The R_INTC interrupt controller handles the NMI interrupt pin for the
SoC. While there is no documentation or code from the vendor for this
device on the A83T, existing mainline kernel drivers and bindings show
this to be similar to the old Allwinner interrupt controller found on
the A10 SoC, but with only the NMI interrupt wired. Register poking
experiments confirm this.
The device seems to be the same across all recent Allwinner SoCs, apart
from the A20 and A80, which have a separate set of registers to handle
the NMI interrupt. We already have a set of bindings supporting this
on the A31.
Add a device node for it, with an SoC specific compatible.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
We introduced a new compatible for the NMI or R_INTC interrupt
controller. This new compatible has the register region aligned
to the boundary listed in the SoC's memory map.
This patch converts the NMI/R_INTC node to using the new compatible,
and fixes up the register region and device node name.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
We introduced a new compatible for the NMI or R_INTC interrupt
controller. This new compatible has the register region aligned
to the boundary listed in the SoC's memory map.
This patch converts the NMI/R_INTC node to using the new compatible,
and fixes up the register region and device node name.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Now that the CCU device tree binding headers have been merged, we can
use the properly named macros in the device tree, instead of raw
numbers.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The datasheet said that emac register size is 0x10000 not 0x104
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[wens@csie.org: Fixed commit subject prefix]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
Pull ARM device-tree updates from Arnd Bergmann:
"Device-tree continues to see lots of updates. The majority of patches
here are smaller changes for new hardware on existing platforms, and
there are a few larger changes worth pointing out.
New machines:
- The new Action Semi S500 platform is added along with initial
support for the LeMaker Guitar board.
- STM32 gains support for three new boards: stm32h743-disco,
stm32f746-disco, and stm32f769-disco, along with new device support
for the existing stm32f429 boards.
- Renesas adds two new boards, the tiny GR-Peach based on RZ/A1H with
10MB on-chip SRAM, and the iWave G20D-Q7 System-on-Module plus
board.
- On Marvell "mvebu", we gain support for the Linksys WRT3200ACM
wireless router.
- For NXP i.MX, we gain support for the Gateworks Ventana GW5600 and
the Technexion Pico i.MX7D single-board computers.
- The BeagleBone Blue is added for OMAP, it's the latest variation of
the popular Beaglebone Black single-board computer.
- The Allwinner based Lichee Pi Zero and NanoPi M1 Plus boards are
added, these are the latest variations of a seemingly endless
supply of similar single-board computers.
Other updates:
- Linus Walleij improves support for the "Faraday" based SoC
platforms from various SoC makers (Moxart, Aspeed, Gemini)
- The ARM Mali GPU is now describe on Rockchips SoCs
- Mediatek MT7623 is extended significantly, making it much more
useful.
- Lots of individual updates on Renesas, OMAP, Rockchips, Broadcom,
Allwinner, Qualcomm, iMX
- For Amlogic, the clock support is extended a lot on meson8b.
- We now build the devicetree file for the Raspberry Pi 3 on 32-bit
ARM, in addition to the existing ARM64 support, to help users
wanting to run a 32-bit system on it"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (345 commits)
ARM: dts: socfpga: set the i2c frequency
ARM: dts: socfpga: Add second ethernet alias to VINING FPGA
ARM: dts: socfpga: Drop LED node from VINING FPGA
ARM: dts: socfpga: Remove I2C EEPROMs from VINING FPGA
ARM: dts: socfpga: Enable QSPI support on VINING FPGA
ARM: dts: socfpga: Fix the ethernet clock phandle
ARM: pxa: Use - instead of @ for DT OPP entries
ARM: dts: owl-s500: Add SPS node
ARM: dts: owl-s500: Set CPU enable-method
dt-bindings: arm: cpus: Add S500 enable-method
ARM: dts: Add Actions Semi S500 and LeMaker Guitar
dt-bindings: arm: Document Actions Semi S900
dt-bindings: timer: Document Owl timer
ARM: dts: imx6q-cm-fx6: add sdio wifi/bt nodes
dt-bindings: arm: Document Actions Semi S500
dt-bindings: Add vendor prefix for Actions Semi
ARM: dts: turris-omnia: Add generic compatible string for I2C EEPROM
ARM: dts: mvebu: add support for Linksys WRT3200ACM (Rango)
ARM: dts: armada-385-linksys: fixup button node names
ARM: dts: armada-385-linksys: group pins in pinctrl
...
|
|
Pull non-urgent ARM SoC fixes from Arnd Bergmann:
"Smaller patches that didn't seem to find a home in other branches, and
low-priority fixes from late in the merge window.
- Lee Jones retires as bcm2835 (raspberry pi) co-maintainer.
- a couple of bugfixes for the ARM CCN bus driver that were regarded
not important enough
- minor device tree fixes for the Renesas and Marvell platforms, that
came a little late or did not justify have another pull request
after the last -rc"
* tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
bus: arm-ccn: Enable stats for CCN-502 interconnect
dt-bindings: arm-ccn: Add bindings info for CCN-502 compatible string
bus: arm-ccn: Use devm_kcalloc() in arm_ccn_probe()
bus: arm-ccn: Fix module autoload
MAINTAINERS: add RV1108 Rockchip soc to maintained files
ARM: dts: kirkwood: Fix Openblock A6 nand partition overlap
ARM: dts: armadillo800eva: Split LCD mux and gpio
MAINTAINERS: Remove Lee Jones from bcm2835.
|
|
Pull MMC updates from Ulf Hansson:
"MMC core:
- Add support to enable irq wake for slot gpio
- Remove MMC_CAP2_HC_ERASE_SZ and make it the default behaviour
- Improve R1 response error checks for stop commands
- Cleanup and clarify some MMC specific code
- Keep card runtime resumed while adding SDIO function devices
- Use device_property_read instead of of_property_read in mmc_of_parse()
- Move boot partition locking into a driver op to enable proper I/O scheduling
- Move multi/single-ioctl() to use block layer to enable proper I/O scheduling
- Delete bounce buffer Kconfig option
- Improve the eMMC HW reset support provided via the eMMC pwrseq
- Add host API to manage SDIO IRQs from a workqueue
MMC host:
- dw_mmc: Drop support for multiple slots
- dw_mmc: Use device_property_read instead of of_property_read
- dw_mmc-rockchip: Optional improved tuning to greatly decrease tuning time
- dw_mmc: Prevent rpm suspend for SDIO IRQs instead of always for SDIO cards
- dw_mmc: Convert to use MMC_CAP2_SDIO_IRQ_NOTHREAD for SDIO IRQs
- omap_hsmmc: Convert to mmc regulator APIs to consolidate code
- omap_hsmmc: Deprecate "vmmc_aux" in DT and use "vqmmc" instead
- tmio: make sure SDIO gets reinitialized after resume
- sdhi: add CMD23 support to R-Car Gen2 & Gen3
- tmio: add CMD23 support
- sdhi/tmio: Refactor code and rename files to simplify Kconfig options
- sdhci-pci: Enable card detect wake for Intel BYT-related SD controllers
- sdhci-pci: Add support for Intel CNP
- sdhci-esdhc-imx: Remove ENGcm07207 workaround - allow multi block transfers
- sdhci-esdhc-imx: Allow all supported prescaler values
- sdhci-esdhc-imx: Fix DAT line software reset
- sdhci-esdhc: Add SDHCI_QUIRK_32BIT_DMA_ADDR
- atmel-mci: Drop AVR32 support"
* tag 'mmc-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (86 commits)
mmc: dw_mmc: remove the unnecessary slot variable
mmc: dw_mmc: use the 'slot' instead of 'cur_slot'
mmc: dw_mmc: remove the 'id' arguments about functions relevant to slot
mmc: dw_mmc: change the array of slots
mmc: dw_mmc: remove the loop about finding slots
mmc: dw_mmc: deprecated the "num-slots" property
mmc: dw_mmc-rockchip: parse rockchip, desired-num-phases from DT
dt-bindings: rockchip-dw-mshc: add optional rockchip, desired-num-phases
mmc: renesas-sdhi: improve checkpatch cleanness
mmc: tmio: improve checkpatch cleanness
mmc: sdhci-pci: Enable card detect wake for Intel BYT-related SD controllers
mmc: slot-gpio: Add support to enable irq wake on cd_irq
mmc: core: Remove MMC_CAP2_HC_ERASE_SZ
mmc: core: for data errors, take response of stop cmd into account
mmc: core: check also R1 response for stop commands
mmc: core: Clarify code for sending CSD
mmc: core: Drop mmc_all_send_cid() and use mmc_send_cxd_native() instead
mmc: core: Re-factor code for sending CID
mmc: core: Remove redundant code in mmc_send_cid()
mmc: core: Make mmc_can_reset() static
...
|
|
mvebu fixes for 4.12 (part 2)
Fix Openblock A6 (kirkwood base board) nand partition overlap
* tag 'mvebu-fixes-4.12-2' of git://git.infradead.org/linux-mvebu:
ARM: dts: kirkwood: Fix Openblock A6 nand partition overlap
arm64: marvell: dts: fix interrupts in 7k/8k crypto nodes
|
|
Pull "Actions Semi ARM based SoC DT for v4.13" from Andreas Färber:
This adds an initial DT for the S500 SoC and a devboard based on it.
* tag 'actions-arm-dt-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-actions:
ARM: dts: owl-s500: Add SPS node
ARM: dts: owl-s500: Set CPU enable-method
dt-bindings: arm: cpus: Add S500 enable-method
ARM: dts: Add Actions Semi S500 and LeMaker Guitar
dt-bindings: arm: Document Actions Semi S900
dt-bindings: timer: Document Owl timer
dt-bindings: arm: Document Actions Semi S500
dt-bindings: Add vendor prefix for Actions Semi
|
|
Merge "Amlogic 32-bit DT changes for v4.13 (round 2)" from Kevin Hilman:
- greatly expands DT clock support for meson8b
* tag 'amlogic-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic: (22 commits)
ARM: dts: meson: use the real ethernet clock on Meson8 and Meson8b
ARM: dts: meson8b: add the SCU device node
ARM: dts: meson: add USB support on Meson8 and Meson8b
ARM: dts: meson: add the hardware random number generator
ARM: dts: meson8: add reserved memory zones
ARM: dts: meson: add the SAR ADC
ARM: dts: meson8: add the pins for the SDIO controller
ARM: dts: meson8: add the PWM_E and PWM_F pins
ARM: dts: meson: use GIC_SPI and IRQ_TYPE_EDGE_RISING macros
ARM: dts: meson: use C preprocessor friendly include syntax
ARM: dts: meson8: fix the IR receiver pins
clk: meson8b: export the ethernet gate clock
clk: meson8b: export the USB clocks
clk: meson8b: export the gate clock for the HW random number generator
clk: meson8b: export the SDIO clock
clk: meson8b: export the SAR ADC clocks
clk: meson-gxbb: un-export the CPU clock
clk: meson-gxbb: expose UART clocks
clk: meson-gxbb: expose SPICC gate
clk: meson-gxbb: expose spdif master clock
...
|
|
Pull "SoCFPGA DTS updates for v4.13" from Dinh Nguyen:
- Fix clocks node the EMACs
- VINING board updtes
- Remove I2C EEPROMs and LED node
- Add QSPI device
- Add 2nd ethernet alias
- Add 'clock-frequency' binding for i2c node
* tag 'socfpga_dts_for_v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: dts: socfpga: set the i2c frequency
ARM: dts: socfpga: Add second ethernet alias to VINING FPGA
ARM: dts: socfpga: Drop LED node from VINING FPGA
ARM: dts: socfpga: Remove I2C EEPROMs from VINING FPGA
ARM: dts: socfpga: Enable QSPI support on VINING FPGA
ARM: dts: socfpga: Fix the ethernet clock phandle
|
|
Use 'clock-frequency' binding for the i2c node that will put the I2C driver
into the standard operating mode. 'speed-mode' was not a valid binding for
the I2C driver, remove it.
Signed-off-by: Alan Tull <atull@kernel.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Add DT alias for the second ethernet present on mainboard rev 1.10.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Drop the LED node from VINing FPGA DT because the LED wiring is
different on each mainboard revision. This wiring is therefore
handled in mainboard DT Overlays.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Remove the EEPROMs attached to the I2C expander ports which
lead to the backplane slots from the main VIN|ING DTS file.
These EEPROMs are bound using separate DTO files, which lets
us handle both two-slot and six-slot configuration of the
backplane.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Enable the QSPI node and add the flash chips.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
The ethernet block clock phandle must point to the clock node which
represents the clock which directly supply the ethernet block. This
is emac_x_clk , not emacx_clk , so fix this.
From: Pavel Machek <pavel@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Pull "pxa-dt for v4.13" from Robert Jarzmik:
This device-tree pxa update brings :
- cpu operating points renaming from Viresh
* tag 'pxa-dt-4.13' of https://github.com/rjarzmik/linux:
ARM: pxa: Use - instead of @ for DT OPP entries
|
|
Pull "Samsung DeviceTree update for v4.13, part two" from Krzysztof Kozłowski:
1. Add needed property for CEC on Odroid U3,
2. Fix reset GPIO polarity on Rinato.
* tag 'samsung-dt-4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Fix polarity of panel reset gpio in Rinato
ARM: dts: exynos: add needs-hpd to &hdmicec for Odroid-U3
|
|
Compiling the DT file with W=1, DTC warns like follows:
Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 has a
unit name, but no reg property
Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
|
|
Pick up dependent changes.
|
|
commit 94647a30124e2c7 ("ARM: dts: omap3-overo: Enable WiFi/BT combo")
while enabling WiFi/BT combo added regulator to trigger the nReset
signal of the Bluetooth module in vqmmc-supply. However BT should be
handled by UART. Moreover "vqmmc" is not a defined binding for
omap_hsmmc. While "vqmmc" in mmc2 hasn't caused any issues so far,
mmc2 will start to mis-behave once omap_hsmmc defines "vqmmc"
binding.
Remove "vqmmc-supply" property in mmc2 here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add Smart Power System node for PM domains.
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
Use a custom S500 enable-method for all CPUs.
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
Pull ARM SoC fixes from Olof Johansson:
"Stream of fixes has slowed down, only a few this week:
- Some DT fixes for Allwinner platforms, and addition of a clock to
the R_CCU clock controller that had been missed.
- A couple of small DT fixes for am335x-sl50"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: allwinner: a64: Add PLL_PERIPH0 clock to the R_CCU
ARM: sunxi: h3-h5: Add PLL_PERIPH0 clock to the R_CCU
ARM: dts: am335x-sl50: Fix cannot claim requested pins for spi0
ARM: dts: am335x-sl50: Fix card detect pin for mmc1
arm64: allwinner: h5: Remove syslink to shared DTSI
ARM: sunxi: h3/h5: fix the compatible of R_CCU
|
|
The i.MX device tree updates for 4.13:
- New board support: Gateworks Ventana GW5600, Technexion Pico i.MX7D
Board.
- A series from Alexandre Belloni to correct the vendor prefix for
rv4162 compatible.
- A patch-set from Andrey Smirnov ot enable PCIe support for i.MX7 and
imx7d-sdb board.
- Increase the SGTL5000 LRCLK pad strength to fix a random audio
channel swapping seen on imx6qdl-wandboard and imx6qdl-colibri
boards.
- Clean up non-existing property 'enable-active-low' from fixed
regulator device nodes.
- Correct GPIO polarity for Ethernet PHY and PCI reset lines, even
though device drivers do not use the polarity for now.
- Add Wifi and Bluetooth support for imx7d-sdb board.
- Adopt the i.MX6Q/DL DT to the new and more flexible GPC binding.
- Update zii-rdu2 device tree source to use #include "..." for local
inclusion.
- A series from Philipp Zabel and Steve Longerbeam to enable video
capture support for imx6qdl platforms.
- A number of small random updates on various board support.
* tag 'imx-dt-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (47 commits)
ARM: dts: imx6q-cm-fx6: add sdio wifi/bt nodes
ARM: dts: ls1021a: update the clockgen node
ARM: dts: imx6-sabreauto: add the ADV7180 video decoder
ARM: dts: imx6-sabreauto: add pinctrl for gpt input capture
ARM: dts: imx6-sabreauto: add reset-gpios property for max7310_b
ARM: dts: imx6-sabreauto: create i2cmux for i2c3
ARM: dts: imx6-sabresd: add OV5642 and OV5640 camera sensors
ARM: dts: imx6-sabrelite: add OV5642 and OV5640 camera sensors
ARM: dts: imx6qdl-sabrelite: remove erratum ERR006687 workaround
ARM: dts: imx6qdl: add capture-subsystem device
ARM: dts: imx6qdl: Add video multiplexers, mipi_csi, and their connections
ARM: dts: imx6qdl: Add compatible, clocks, irqs to MIPI CSI-2 node
ARM: dts: imx6qdl: add multiplexer controls
ARM: dts: imx6: Fix PCI GPIO reset polarity
ARM: dts: imx7d-sdb: Add Bluetooth support
ARM: dts: imx7d-sdb: Add Wifi support
ARM: dts: imx7d-sdb: Adjust the regulator nodes
ARM: dts: imx: Fix Ethernet PHY reset polarity
ARM: dts: imx7: Fix typo in watchdog pin name
ARM: dts: vf610-zii: Add switch eeprom-length properties
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
mvebu dt for 4.13 (part 1)
- Add Linksys WRT3200ACM (Rango) support
- Add PWM properties for gpio on Aramda XP and 38x
- A couple of minor updates for the 98dx3236 and 98dx4251
* tag 'mvebu-dt-4.13-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: turris-omnia: Add generic compatible string for I2C EEPROM
ARM: dts: mvebu: add support for Linksys WRT3200ACM (Rango)
ARM: dts: armada-385-linksys: fixup button node names
ARM: dts: armada-385-linksys: group pins in pinctrl
ARM: dts: armada-385-linksys: partition layout is board specific
ARM: dts: armada-385-linksys: use binary unit prefixes
ARM: dts: armada-385-linksys: drop legacy DSA bindings
ARM: dts: armada-385-linksys: usb3 label cleanup
ARM: dts: armada-385-linksys: bm pools by label order
ARM: dts: armada-385-linksys: drop redundant properties in dependants
ARM: dts: armada-385-linksys: flatten dependants
ARM: dts: armada-385-linksys: label nodes
ARM: dts: armada-385-linksys: flatten dtsi
ARM: dts: mvebu: disable the rtc on 98dx3236 SoC
ARM: dts: mvebu: add missing interrupt to 98dx4251 switch
ARM: dts: armada-xp: Use pwm-fan rather than gpio-fan
ARM: dts: mvebu: Add PWM properties for armada-38x
ARM: dts: mvebu: Add PWM properties to .dtsi files
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
DT for 4.13
- Switch to the new NAND binding
- A few non urgent fixes
* tag 'at91-ab-4.13-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: dts: at91: sama5d2_xplained: remove wrong memory node
ARM: dts: at91: sama5d2_xplained: add pwm controller
ARM: dts: at91: Add the NOR flash available on sama5d3 dev kits
ARM: dts: at91: Switch to the new NAND bindings
ARM: dts: at91: Declare EBI/NAND controllers
dt-bindings: mtd: atmel-nand: Document the nfc-io bindings
ARM: dts: at91-sama5d4: use IRQ_TYPE_* to specify irq flags
dts: gpio_atmel: adapt binding doc to reality
ARM: dts: at91: sama5d2: add m_can nodes
ARM: dts: at91: Add generic compatible string for I2C EEPROM
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Second Round of Renesas ARM Based SoC DT Updates for v4.13
Cleanup:
* Correct PCI bus dtc warnings for r8a779x SoCs
Enhancements:
* Add support for iWave G20D-Q7 board based on RZ/G1M SoC
* Add support for GR-Peach board based on r7s72100 SoC
* Add composite video and HDMI input to gose board
* tag 'renesas-dt2-for-v4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: dts: r8a779x: Fix PCI bus dtc warnings
ARM: dts: iwg20d-q7: Add support for iWave G20D-Q7 board based on RZ/G1M
ARM: dts: iwg20m: Add iWave RZG1M Qseven SOM
ARM: dts: gose: add composite video input
ARM: dts: r7s72100: Add support for GR-Peach
ARM: dts: gose: add HDMI input
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Qualcomm Device Tree Changes for v4.13
* Fix IPQ4019 i2c0 node
* Add GSBI7 on IPQ8064
* Add misc APQ8060 devices
* Fixup USB related devices on APQ8064 and MSM8974
* tag 'qcom-dts-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
ARM: dts: add core I2C devices to the APQ8060 Dragonboard
ARM: dts: add GSBI8 defines to the MSM8660 family
ARM: dts: Qualcomm APQ8060 DragonBoard ALS sensor
ARM: dts: add XOADC and IIO HWMON to MSM8660/APQ8060
ARM: dts: qcom: ipq4019: fix i2c_0 node
ARM: dts: qcom: add gsbi7 serial to ipq8064 SoC device tree
ARM: dts: qcom-apq8064: Collapse usb support into one node
ARM: dts: qcom-msm8974: Add HS usb node and OTG detection mechanisms
ARM: dts: qcom: add charger otg regulator
ARM: dts: qcom: Remove s4/5vs1,2 from RPM pm8941 control
Signed-off-by: Olof Johansson <olof@lixom.net>
|
Maxime Ripard
Chen-Yu Tsai
Marcus Cooper
Alexander Syring
Corentin Labbe
Linus Torvalds
Arnd Bergmann
Dinh Nguyen
Marek Vasut
Viresh Kumar
Thomas Gleixner
Kishon Vijay Abraham I
Andreas Färber
Olof Johansson