| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
mvebu fixes for 5.0 (part 2)
Fix PHY reset signal on clearfog gt 8K (Armada 8040 based)
Fix NAND description on Armada XP boards which was broken since a few
release
* tag 'mvebu-fixes-5.0-2' of git://git.infradead.org/linux-mvebu:
arm64: dts: clearfog-gt-8k: fix SGMII PHY reset signal
ARM: dts: armada-xp: fix Armada XP boards NAND description
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Two am335x ethernet phy mode fixes for v5.0-rc cycle
Recent changes with commit cd28d1d6e52e: ("net: phy: at803x: Disable phy
delay for RGMII mode") broke Ethernet on am335x-evmsk, and turns out some
device driver fixes are needed.
Even without the driver fixes, am335x needs to run in rgmii-id mode instead
rgmii-txid mode. Things have been working based on luck as the broken driver
has been configuring rgmii-id mode. Let's fix that as that way things work
as they're supposed to work from hardware wiring point of view.
* tag 'omap-for-v5.0/fixes-rc7-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-evm: Fix PHY mode for ethernet
ARM: dts: am335x-evmsk: Fix PHY mode for ethernet
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Commit 482997699ef0 ("ARM: tegra: Fix unit_address_vs_reg DTC warnings
for /memory") inadventently broke device tree ABI by adding a unit-
address to the "/memory" node because the device tree compiler flagged
the missing unit-address as a warning.
Tegra124 Chromebooks (a.k.a. Nyan) use a bootloader that relies on the
full name of the memory node in device tree being exactly "/memory". It
can be argued whether this was a good decision or not, and some other
bootloaders (such as U-Boot) do accept a unit-address in the name of the
node, but the device tree is an ABI and we can't break existing setups
just because the device tree compiler considers it bad practice to omit
the unit-address nowadays.
This partially reverts the offending commit and restores device tree ABI
compatibility.
Fixes: 482997699ef0 ("ARM: tegra: Fix unit_address_vs_reg DTC warnings for /memory")
Reported-by: Tristan Bastian <tristan-c.bastian@gmx.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tested-by: Tristan Bastian <tristan-c.bastian@gmx.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
|
|
The PHY must add both tx and rx delay and not only on the tx clock.
The board uses AR8031_AL1A PHY where the rx delay is enabled by default,
the tx dealy is disabled.
The reason why rgmii-txid worked because the rx delay was not disabled by
the driver so essentially we ended up with rgmii-id PHY mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The PHY must add both tx and rx delay and not only on the tx clock.
The board uses AR8031_AL1A PHY where the rx delay is enabled by default,
the tx dealy is disabled.
The reason why rgmii-txid worked because the rx delay was not disabled by
the driver so essentially we ended up with rgmii-id PHY mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 3b79919946cd2cf4dac47842afc9a893acec4ed7 ("ARM: dts:
armada-370-xp: update NAND node with new bindings") updated some
Marvell Armada DT description to use the new NAND controller bindings,
but did it incorrectly for a number of boards: armada-xp-gp,
armada-xp-db and armada-xp-lenovo-ix4-300d. Due to this, the NAND is
no longer detected on those platforms.
This commit fixes that by properly using the new NAND DT binding. This
commit was runtime-tested on Armada XP GP, the two other platforms are
only compile-tested.
Fixes: 3b79919946cd2 ("ARM: dts: armada-370-xp: update NAND node with new bindings")
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Drop one non-existent component from powerdomain list.
* tag 'v5.0-rockchip-dts32fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: remove qos_cif1 from rk3188 power-domain
|
|
SoC fixes for omaps for v5.0-rc cycle
This series contains two SoC regression fixes and one uninitialized
variable fix:
- Fix inverted nirq pin handling for omap5 that started producing
warnings with earlier GIC direction checks and took a while to
understand and confirm. Basically there are two sys_nirq pins
that are bypassing peripheral modules and inverted automatically
by the SoC and need to be handled with a custom irq_set_type()
- Recent ti-sysc changes caused a regression to the pwm-omap-dmtimer
code where the device tree handling code for timer source clock
gets confused. It looks like we can remove that code eventually,
but for now we just drop a bogus pm_runtime_irq_safe() for the
timers with the related quirks caused by pm_runtime_irq_safe(),
and have the standard assigned-clocks and assigned-clock-parents
deal with setting the source clock
- Fix potentially uninitialized value for display init code if
regmap_read() fails
* tag 'omap-for-v5.0/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Variable "reg" in function omap4_dsi_mux_pads() could be uninitialized
ARM: dts: Configure clock parent for pwm vibra
bus: ti-sysc: Fix timer handling with drop pm_runtime_irq_safe()
ARM: OMAP5+: Fix inverted nirq pin interrupts with irq_set_type
clocksource: timer-ti-dm: Fix pwm dmtimer usage of fck reparenting
|
|
Third Round of Renesas ARM Based SoC Fixes for v5.0
* Convert to new LVDS DT bindings fixing a regression introduced in v4.17
* tag 'renesas-fixes3-for-v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: dts: r8a7743: Convert to new LVDS DT bindings
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Allwinner Fixes for 5.0
A couple of device tree fixes for the 5.0 cycle:
- Add missing clock-output-names for the osc24M clock on sun6i/A31
The Linux clock driver uses the device node as the clock name if
the property is missing. The node name was changed in 5.0-rc1,
breaking a subtle dependency in the sunxi-ng clock driver, and
renders Linux unable to completely boot up.
- Add alias for Ethernet controller on Beelink X2
This allows the bootloader to assign a deterministically generated
MAC address to it.
- Add property to enable USB VBUS regulator on OrangePi Win
The board had defined the constraints for the regulator, but was
missing the property to actually enable it.
* tag 'sunxi-fixes-for-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: a64: Fix USB OTG regulator
ARM: dts: sun8i: h3: Add ethernet0 alias to Beelink X2
ARM: dts: sun6i: Add clock-output-names to osc24M clock
arm64: dts: allwinner: a64: Fix the video engine compatible
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Amlogic fixes for v5.0-rc, round 2
- several fixups for the GPIO cd-inverted change
- IRQ trigger fixes for MAC IRQ
* tag 'amlogic-fixes-2.1' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
arm64: dts: meson: Fix mmc cd-gpios polarity
ARM: dts: meson8m2: mxiii-plus: mark the SD card detection GPIO active-low
ARM: dts: meson8b: ec100: mark the SD card detection GPIO active-low
ARM: dts: meson8b: odroidc1: mark the SD card detection GPIO active-low
arm: dts: meson: Fix IRQ trigger type for macirq
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Device tree fixes for omaps for v5.0-rc cycle
This series of dts fixes for omap devices fixes several device specific
regressions:
- The onenand timings for n950/n9 have been wrong for a while since
we moved to dts based timings
- A typo for the cpcap pmic is now producing erors during boot as the
level should be 0 for unconfigurable triggering instead of 1
- Changes for ti-sysc for omap5 left uart3 with debug flags that should
not be set
- Fix a new dtc warning started showing up for omap3-gta04 grap_port
- With the generic MMC card detection code we need to fix the gpio
in dts for n900 and am335x-shc
* tag 'omap-for-v5.0/fixes-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-shc.dts: fix wrong cd pin level
ARM: dts: n900: fix mmc1 card detect gpio polarity
ARM: dts: omap3-gta04: Fix graph_port warning
ARM: dts: Remove unnecessary idle flags for omap5 uart3
ARM: dts: omap4-droid4: Fix typo in cpcap IRQ flags
ARM: OMAP: dts: N950/N9: fix onenand timings
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This fixes a long standing typo in device-tree for DA850 in interrupt
number for timer. It did not affect us so far because we use non-DT
timer driver within mach-davinci. This was caught while migrating to
clocksource driver.
* tag 'davinci-fixes-for-v5.0-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850: fix interrupt numbers for clocksource
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
i.MX fixes for 5.0:
- Fix spi_bus_bridge DTC warning by correcting '#address-cells' of
dspi3 node on vf610-bk4 board, as it's being used a SPI slave
controller there.
- Replace deprecated gpio-key,wakeup property with wakeup-source for
board imx6q-pistachio and imx6sll-evk, into which the deprecated
property sneaked during the merge window.
- Correct the backward compatible for i.MX6SX GPT device, as it's
actually compatible with i.MX6DL GPT rather than i.MX31 one.
* tag 'imx-fixes-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6sx: correct backward compatible of gpt
ARM: dts: imx: replace gpio-key,wakeup with wakeup-source property
ARM: dts: vf610-bk4: fix incorrect #address-cells for dspi3
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
|
|
Commit 84badc5ec5fc ("ARM: dts: omap4: Move l4 child devices to probe
them with ti-sysc") moved some omap4 timers to probe with ti-sysc
interconnect target module. Turns out this broke pwm-omap-dmtimer
for reparenting of the timer clock.
With ti-sysc, we can now configure the clock sources in the dts with
assigned-clocks and assigned-clock-parents.
Fixes: 84badc5ec5fc ("ARM: dts: omap4: Move l4 child devices to probe them with ti-sysc")
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 83a86fbb5b56 ("irqchip/gic: Loudly complain about the use of
IRQ_TYPE_NONE") started warning about incorrect dts usage for irqs.
ARM GIC only supports active-high interrupts for SPI (Shared Peripheral
Interrupts), and the Palmas PMIC by default is active-low.
Palmas PMIC allows changing the interrupt polarity using register
PALMAS_POLARITY_CTRL_INT_POLARITY, but configuring sys_nirq1 with
a pull-down and setting PALMAS_POLARITY_CTRL_INT_POLARITY made the
Palmas RTC interrupts stop working. This can be easily tested with
kernel tools rtctest.c.
Turns out the SoC inverts the sys_nirq pins for GIC as they do not go
through a peripheral device but go directly to the MPUSS wakeupgen.
I've verified this by muxing the interrupt line temporarily to gpio_wk16
instead of sys_nirq1. with a gpio, the interrupt works fine both
active-low and active-high with the SoC internal pull configured and
palmas polarity configured. But as sys_nirq1, the interrupt only works
when configured ACTIVE_LOW for palmas, and ACTIVE_HIGH for GIC.
Note that there was a similar issue earlier with tegra114 and palmas
interrupt polarity that got fixed by commit df545d1cd01a ("mfd: palmas:
Provide irq flags through DT/platform data"). However, the difference
between omap5 and tegra114 is that tegra inverts the palmas interrupt
twice, once when entering tegra PMC, and again when exiting tegra PMC
to GIC.
Let's fix the issue by adding a custom wakeupgen_irq_set_type() for
wakeupgen and invert any interrupts with wrong polarity. Let's also
warn about any non-sysnirq pins using wrong polarity. Note that we
also need to update the dts for the level as IRQ_TYPE_NONE never
has irq_set_type() called, and let's add some comments and use proper
pin nameing to avoid more confusion later on.
Cc: Belisko Marek <marek.belisko@gmail.com>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: "Dr. H. Nikolaus Schaller" <hns@goldelico.com>
Cc: Jon Hunter <jonathanh@nvidia.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: stable@vger.kernel.org # v4.17+
Reported-by: Belisko Marek <marek.belisko@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
cd pin on mmc1 is GPIO_ACTIVE_LOW not GPIO_ACTIVE_HIGH
Fixes: e63201f19438 ("mmc: omap_hsmmc: Delete platform data GPIO CD and WP")
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We're currently getting a warning with make dtbs:
arch/arm/boot/dts/omap3-gta04.dtsi:720.7-727.4: Warning (graph_port):
/ocp@68000000/dss@48050000/encoder@48050c0 0/port: graph node unit
address error, expected "0"
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Wrong polarity of card detect GPIO pin leads to the system not
booting from external mmc, if the back cover of N900 is closed.
When the cover is open the system boots fine.
This wasn't noticed before, because of a bug, which was fixed
by commit e63201f19 (mmc: omap_hsmmc: Delete platform data GPIO
CD and WP).
Kernels up to 4.19 ignored the card detect GPIO from DT.
Fixes: e63201f19438 ("mmc: omap_hsmmc: Delete platform data GPIO CD and WP")
Signed-off-by: Arthur Demchenkov <spinal.by@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The internal LVDS encoder now has DT bindings separate from the DU. Port
the device tree over to the new model.
Fixes: c6a27fa41fab ("drm: rcar-du: Convert LVDS encoder code to bridge driver")
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The timer interrupts specified in commit 3652e2741f42 ("ARM: dts:
da850: Add clocks") are wrong but since the current timer code
hard-codes them, the bug was never spotted.
This patch must go into stable since, once we introduce a proper
clocksource driver, devices with buggy device tree will stop booting.
Fixes: 3652e2741f42 ("ARM: dts: da850: Add clocks")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
mvebu fixes for 5.0
They are all device tree fixes which also worth being in stable:
- Reserve PSCI area on Armada 7K/8K preventing the kernel accessing
this area and crashing while doing it.
- Use correct PCIe reset signal on MACCHIATOBin (Armada 8040 based)
- Fix polarity of GPIO fan line D-Link DNS NASes(kikwood based)
* tag 'mvebu-fixes-5.0-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: kirkwood: Fix polarity of GPIO fan lines
arm64: dts: marvell: mcbin: fix PCIe reset signal
arm64: dts: marvell: armada-ap806: reserve PSCI area
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
i.MX6SX has same GPT type as i.MX6DL, in GPT driver, it uses
below TIMER_OF_DECLARE, so the backward compatible should be
"fsl,imx6dl-gpt", correct it.
TIMER_OF_DECLARE(imx6sx_timer, "fsl,imx6sx-gpt", imx6dl_timer_init_dt);
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Most of the legacy "gpio-key,wakeup" and "enable-sdio-wakeup" boolean
properties are already replaced with "wakeup-source". However few
occurrences of old property has popped up again, probably from the
remnants in downstream trees. Almost all of those were remove couple
of years back.
Replace the legacy properties with the unified "wakeup-source" property
introduced in the commit 700a38b27eef ("Input: gpio_keys - switch to using
generic device properties") and commit 0dbcdc0622ea ("mmc: core: enable
support for the standard "wakeup-source" property")
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The dspi3 is used as slave controller on vf610-bk4, and the default
'#address-cells = <1>;' setting in vfxxx.dtsi causes the following DTC
warning.
DTC arch/arm/boot/dts/vf610-bk4.dtb
../arch/arm/boot/dts/vfxxx.dtsi:550.24-563.6: Warning (spi_bus_bridge): /soc/aips-bus@40080000/spi@400ad000: incorrect #address-cells for SPI bus
also defined at ../arch/arm/boot/dts/vf610-bk4.dts:107.8-119.3
arch/arm/boot/dts/vf610-bk4.dtb: Warning (spi_bus_reg): Failed prerequisite 'spi_bus_bridge'
For spi device used as slave controller, '#address-cells' should be 0.
Let's overwrite the property in vf610-bk4.dts to fix the warning.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
After commit 89a5e15bcba87d ("gpio/mmc/of: Respect polarity in the device
tree") SD cards are not detected anymore.
The CD GPIO is "active low" on the MXIII-Plus. The MMC dt-bindings
specify: "[...] using the "cd-inverted" property means, that the CD line
is active high, i.e. it is high, when a card is inserted".
Fix the description of the SD card by marking it as GPIO_ACTIVE_LOW and
drop the "cd-inverted" property. This makes the definition consistent
with the existing dt-bindings and fixes the check whether an SD card is
inserted.
Fixes: 35ee52bea66c74 ("ARM: dts: meson8m2: add support for the Tronsmart MXIII Plus")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
After commit 89a5e15bcba87d ("gpio/mmc/of: Respect polarity in the device
tree") SD cards are not detected anymore.
The CD GPIO is "active low" on the EC-100. The MMC dt-bindings specify:
"[...] using the "cd-inverted" property means, that the CD line is active
high, i.e. it is high, when a card is inserted".
Fix the description of the SD card by marking it as GPIO_ACTIVE_LOW and
drop the "cd-inverted" property. This makes the definition consistent
with the existing dt-bindings and fixes the check whether an SD card is
inserted.
Fixes: bbedc1f1d90e33 ("ARM: dts: meson8b: Add support for the Endless Mini (EC-100)")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
After commit 89a5e15bcba87d ("gpio/mmc/of: Respect polarity in the device
tree") SD cards are not detected anymore.
The CD GPIO is "active low" on Odroid-C1. The MMC dt-bindings specify:
"[...] using the "cd-inverted" property means, that the CD line is active
high, i.e. it is high, when a card is inserted".
Fix the description of the SD card by marking it as GPIO_ACTIVE_LOW and
drop the "cd-inverted" property. This makes the definition consistent
with the existing dt-bindings and fixes the check whether an SD card is
inserted.
Fixes: e03efbce6bebf5 ("ARM: dts: meson8b-odroidc1: add microSD support")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
A long running stress test on a custom board shipping an AXG SoCs and a
Realtek RTL8211F PHY revealed that after a few hours the connection
speed would drop drastically, from ~1000Mbps to ~3Mbps. At the same time
the 'macirq' (eth0) IRQ would stop being triggered at all and as
consequence the GMAC IRQs never ACKed.
After a painful investigation the problem seemed to be due to a wrong
defined IRQ type for the GMAC IRQ that should be LEVEL_HIGH instead of
EDGE_RISING.
The change in the macirq IRQ type also solved another long standing
issue affecting this SoC/PHY where EEE was causing the network
connection to die after stressing it with iperf3 (even though much
sooner). It's now possible to remove the 'eee-broken-1000t' quirk as
well.
Fixes: 9c15795a4f96 ("ARM: dts: meson8b-odroidc1: ethernet support")
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
These two lines are active high, not active low. The bug was
found when we changed the kernel to respect the polarity defined
in the device tree.
Fixes: 1b90e06b1429 ("ARM: kirkwood: Use devicetree to define DNS-32[05] fan")
Cc: Jamie Lentin <jm@lentin.co.uk>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@bootlin.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Julien D'Ascenzio <jdascenzio@posteo.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Reported-by: Julien D'Ascenzio <jdascenzio@posteo.net>
Tested-by: Julien D'Ascenzio <jdascenzio@posteo.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
To avoid the following error:
asoc-simple-card sound: ASoC: Failed to create card debugfs directory
Which is because the card name contains '/' character, which can not be
used in file or directory names.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Add the board level fixed regulators for 3.3V and 1.8V which is used to
power - among other things - the tlv320aic3106 codec.
Apart from removing the following warning during boot:
tlv320aic3x-codec 0-0018: Invalid supply voltage(s) AVDD: -22, DVDD: -22
With the correct voltages the driver can select correct OCMV value to
reduce pop noise.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
To avoid the following error:
asoc-simple-card sound: ASoC: Failed to create card debugfs directory
Which is because the card name contains '/' character, which can not be
used in file or directory names.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Add the board level fixed regulators for 3.3V and 1.8V which is used to
power - among other things - the tlv320aic3106 codec.
Apart from removing the following warning during boot:
tlv320aic3x-codec 0-0018: Too high supply voltage(s) AVDD: 5000000, DVDD: 5000000
With the correct voltages the driver can select correct OCMV value to
reduce pop noise.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Because "ethernet0" alias is missing, U-Boot doesn't generate board
specific MAC address. Effect of this is random MAC address every boot
and thus new IP address is assigned to the board.
Fix this by adding alias.
Fixes: 7389172fc3ed ("ARM: dts: sun8i: h3: Enable dwmac-sun8i on the Beelink X2")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
[Maxime: Removed unneeded comment]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The osc24M clock does not have a "clock-output-names" property, which
means that the clock name is derived from the node name in Linux. The
node name was changed in commit acfd5bbe2641 ("ARM: dts: sun6i: Change
clock node names to avoid warnings"). This breaks Linux as the sunxi-ng
clock driver implicitly depends on the external clock being named
"osc24M".
Add a "clock-output-names" property to restore the previous behavior.
Fixes: acfd5bbe2641 ("ARM: dts: sun6i: Change clock node names to avoid
warnings")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Looks like I accidentally left some extra flags for uart3 to
not idle it. This happened as I generated the data from a
running system where these flags are set dynamically on boot
by omap_hwmod_setup_earlycon_flags() if earlycon is enabled.
We can just remove them.
Fixes: 4c387984618f ("ARM: dts: omap5: Add l4 interconnect hierarchy and ti-sysc data")
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We're now getting the following error:
genirq: Setting trigger mode 1 for irq 230 failed
(regmap_irq_set_type+0x0/0x15c)
cpcap-usb-phy cpcap-usb-phy.0: could not get irq dp: -524
Cc: Sebastian Reichel <sre@kernel.org>
Reported-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit a758f50f10cf ("mtd: onenand: omap2: Configure driver from DT")
started using DT specified timings for GPMC, and as a result the
OneNAND stopped working on N950/N9 as we had wrong values in the DT.
Fix by updating the values to bootloader timings that have been tested
to be working on both Nokia N950 and N9.
Fixes: a758f50f10cf ("mtd: onenand: omap2: Configure driver from DT")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
While the rk3066 does have 2 camera interfaces, the rk3188 does not, so
there also isn't a QoS block for that non-existing interface, so remove it.
Fixes: e6e1869f0b71 ("ARM: dts: rockchip: add rk3066/rk3188 power-domains")
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Pull PCI updates from Bjorn Helgaas:
- Remove unused lists from ASPM pcie_link_state (Frederick Lawler)
- Fix Broadcom CNB20LE host bridge unintended sign extension (Colin Ian
King)
- Expand Kconfig "PF" acronyms (Randy Dunlap)
- Update MAINTAINERS for arch/x86/kernel/early-quirks.c (Bjorn Helgaas)
- Add missing include to drivers/pci.h (Alexandru Gagniuc)
- Override Synopsys USB 3.x HAPS device class so dwc3-haps can claim it
instead of xhci (Thinh Nguyen)
- Clean up P2PDMA documentation (Randy Dunlap)
- Allow runtime PM even if driver doesn't supply callbacks (Jarkko
Nikula)
- Remove status check after submitting Switchtec MRPC Firmware Download
commands to avoid Completion Timeouts (Kelvin Cao)
- Set Switchtec coherent DMA mask to allow 64-bit DMA (Boris Glimcher)
- Fix Switchtec SWITCHTEC_IOCTL_EVENT_IDX_ALL flag overwrite issue
(Joey Zhang)
- Enable write combining for Switchtec MRPC Input buffers (Kelvin Cao)
- Add Switchtec MRPC DMA mode support (Wesley Sheng)
- Skip VF scanning on powerpc, which does this in firmware (Sebastian
Ott)
- Add Amlogic Meson PCIe controller driver and DT bindings (Yue Wang)
- Constify histb dw_pcie_host_ops structure (Julia Lawall)
- Support multiple power domains for imx6 (Leonard Crestez)
- Constify layerscape driver data (Stefan Agner)
- Update imx6 Kconfig to allow imx6 PCIe in imx7 kernel (Trent Piepho)
- Support armada8k GPIO reset (Baruch Siach)
- Support suspend/resume support on imx6 (Leonard Crestez)
- Don't hard-code DesignWare DBI/ATU offst (Stephen Warren)
- Skip i.MX6 PHY setup on i.MX7D (Andrey Smirnov)
- Remove Jianguo Sun from HiSilicon STB maintainers (Lorenzo Pieralisi)
- Mask DesignWare interrupts instead of disabling them to avoid lost
interrupts (Marc Zyngier)
- Add locking when acking DesignWare interrupts (Marc Zyngier)
- Ack DesignWare interrupts in the proper callbacks (Marc Zyngier)
- Use devm resource parser in mediatek (Honghui Zhang)
- Remove unused mediatek "num-lanes" DT property (Honghui Zhang)
- Add UniPhier PCIe controller driver and DT bindings (Kunihiko
Hayashi)
- Enable MSI for imx6 downstream components (Richard Zhu)
* tag 'pci-v4.21-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (40 commits)
PCI: imx: Enable MSI from downstream components
s390/pci: skip VF scanning
PCI/IOV: Add flag so platforms can skip VF scanning
PCI/IOV: Factor out sriov_add_vfs()
PCI: uniphier: Add UniPhier PCIe host controller support
dt-bindings: PCI: Add UniPhier PCIe host controller description
PCI: amlogic: Add the Amlogic Meson PCIe controller driver
dt-bindings: PCI: meson: add DT bindings for Amlogic Meson PCIe controller
arm64: dts: mt7622: Remove un-used property for PCIe
arm: dts: mt7623: Remove un-used property for PCIe
dt-bindings: PCI: MediaTek: Remove un-used property
PCI: mediatek: Remove un-used variant in struct mtk_pcie_port
MAINTAINERS: Remove Jianguo Sun from HiSilicon STB DWC entry
PCI: dwc: Don't hard-code DBI/ATU offset
PCI: imx: Add imx6sx suspend/resume support
PCI: armada8k: Add support for gpio controlled reset signal
PCI: dwc: Adjust Kconfig to allow IMX6 PCIe host on IMX7
PCI: dwc: layerscape: Constify driver data
PCI: imx: Add multi-pd support
PCI: Override Synopsys USB 3.x HAPS device class
...
|
|
Pull more ARM SoC updates from Olof Johansson:
"A few updates that we merged late but are low risk for regressions for
other platforms (and a few other straggling patches):
- I mis-tagged the 'drivers' branch, and missed 3 patches. Merged in
here. They're for a driver for the PL353 SRAM controller and a
build fix for the qualcomm scm driver.
- A new platform, RDA Micro RDA8810PL (Cortex-A5 w/ integrated
Vivante GPU, 256MB RAM, Wifi). This includes some acked
platform-specific drivers (serial, etc). This also include DTs for
two boards with this SoC, OrangePi 2G and OrangePi i86.
- i.MX8 is another new platform (NXP, 4x Cortex-A53 + Cortex-M4, 4K
video playback offload). This is the first i.MX 64-bit SoC.
- Some minor updates to Samsung boards (adding a few peripherals in
DTs).
- Small rework for SMP bootup on STi platforms.
- A couple of TEE driver fixes.
- A couple of new config options (bcm2835 thermal, Uniphier MDMAC)
enabled in defconfigs"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (27 commits)
ARM: multi_v7_defconfig: enable CONFIG_UNIPHIER_MDMAC
arm64: defconfig: Re-enable bcm2835-thermal driver
MAINTAINERS: Add entry for RDA Micro SoC architecture
tty: serial: Add RDA8810PL UART driver
ARM: dts: rda8810pl: Add interrupt support for UART
dt-bindings: serial: Document RDA Micro UART
ARM: dts: rda8810pl: Add timer support
ARM: dts: Add devicetree for OrangePi i96 board
ARM: dts: Add devicetree for OrangePi 2G IoT board
ARM: dts: Add devicetree for RDA8810PL SoC
ARM: Prepare RDA8810PL SoC
dt-bindings: arm: Document RDA8810PL and reference boards
dt-bindings: Add RDA Micro vendor prefix
ARM: sti: remove pen_release and boot_lock
arm64: dts: exynos: Add Bluetooth chip to TM2(e) boards
arm64: dts: imx8mq-evk: enable watchdog
arm64: dts: imx8mq: add watchdog devices
MAINTAINERS: add i.MX8 DT path to i.MX architecture
arm64: add support for i.MX8M EVK board
arm64: add basic DTS for i.MX8MQ
...
|
|
Pull ARM Device-tree updates from Olof Johansson:
"As usual, this is where the bulk of our changes end up landing each
merge window.
The individual updates are too many to enumerate, many many platforms
have seen additions of device descriptions such that they are
functionally more complete (in fact, this is often the bulk of updates
we see).
Instead I've mostly focused on highlighting the new platforms below as
they are introduced. Sometimes the introduction is of mostly a
fragment, that later gets filled in on later releases, and in some
cases it's near-complete platform support. The latter is more common
for derivative platforms that already has similar support in-tree.
Two SoCs are slight outliers from the usual range of additions.
Allwinner support for F1C100s, a quite old SoC (ARMv5-based) shipping
in the Lychee Pi Nano platform. At the other end is NXP Layerscape
LX2160A, a 16-core 2.2GHz Cortex-A72 SoC with a large amount of I/O
aimed at infrastructure/networking.
TI updates stick out in the diff stats too, in particular because they
have moved the description of their L4 on-chip interconnect to
devicetree, which opens up for removal of even more of their
platform-specific 'hwmod' description tables over the next few
releases.
SoCs:
- Qualcomm QCS404 (4x Cortex-A53)
- Allwinner T3 (rebranded R40) and f1c100s (armv5)
- NXP i.MX7ULP (1x Cortex-A7 + 1x Cortex-M4)
- NXP LS1028A (2x Cortex-A72), LX2160A (16x Cortex-A72)
New platforms:
- Rockchip: Gru Scarlet (RK3188 Tablet)
- Amlogic: Phicomm N1 (S905D), Libretech S805-AC
- Broadcom: Linksys EA6500 v2 Wi-Fi router (BCM4708)
- Qualcomm: QCS404 base platform and EVB
- Qualcomm: Remove of Arrow SD600
- PXA: First PXA3xx DT board: Raumfeld
- Aspeed: Facebook Backpack-CMM BMC
- Renesas iWave G20D-Q7 (RZ/G1N)
- Allwinner t3-cqa3t-bv3 (T3/R40) and Lichee Pi Nano (F1C100s)
- Allwinner Emlid Neutis N5, Mapleboard MP130
- Marvell Macchiatobin Single Shot (Armada 8040, no 10GbE)
- i.MX: mtrion emCON-MX6, imx6ul-pico-pi, imx7d-sdb-reva
- VF610: Liebherr's BK4 device, ZII SCU4 AIB board
- i.MX7D PICO Hobbit baseboard
- i.MX7ULP EVK board
- NXP LX2160AQDS and LX2160ARDB boards
Other:
- Coresight binding updates across the board
- CPU cooling maps updates across the board"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (648 commits)
ARM: dts: suniv: Fix improper bindings include patch
ARM: dts: sunxi: Enable Broadcom-based Bluetooth for multiple boards
arm64: dts: allwinner: a64: bananapi-m64: Add Bluetooth device node
ARM: dts: suniv: Fix improper bindings include patch
arm64: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
arm64: dts: Remove unused properties from FSL QSPI driver nodes
ARM: dts: Add spi-[tx/rx]-bus-width for the FSL QSPI controller
ARM: dts: imx6sx-sdb: Fix the reg properties for the FSL QSPI nodes
ARM: dts: Remove unused properties from FSL QSPI driver nodes
arm64: dts: ti: k3-am654: Enable main domain McSPI0
arm64: dts: ti: k3-am654: Add McSPI DT nodes
arm64: dts: ti: k3-am654: Populate power-domain property for UART nodes
arm64: dts: ti: k3-am654-base-board: Enable ECAP PWM
arm64: dts: ti: k3-am65-main: Add ECAP PWM node
arm64: dts: ti: k3-am654-base-board: Add I2C nodes
arm64: dts: ti: am654-base-board: Add pinmux for main uart0
arm64: dts: ti: k3-am65: Add pinctrl regions
dt-bindings: pinctrl: k3: Introduce pinmux definitions
ARM: dts: exynos: Specify I2S assigned clocks in proper node
ARM: dts: exynos: Add missing CPUs in cooling maps for Odroid X2
...
|
|
Pull arm SoC platform updates from Olof Johansson:
"SoC updates, mostly refactorings and cleanups of old legacy platforms,
but also a few more things:
New SoC support this release:
- NXP/Freescale i.MX7ULP (1x Cortex-A7, Cortex-M4, graphics, etc)
- Allwinner F1C100, older platform with an ARM926-EJS (ARMv5) core
Cleanups of various platforms:
- OMAP1 ams-delta does some GPIO cleanups
- Davinci removes of at24 platform data
- Samsung cleans up old wakeup, PM debug and secondary core boot code
- Renesas moves around config options and PM code to drivers/soc for
sharing with 64-bit and more consistency
- i.MX, Broadcom and SoCFPGA all have tweaks to lowlevel debug
console setups
- SoCFPGA adds explicit selection of ARM errata and removes some
unused code
This also contains a few patches that I had queued up as fixes for
4.20 but didn't send in before the release"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (68 commits)
arm64: dts: renesas: draak: Fix CVBS input
ARM: omap2: avoid section mismatch warning
ARM: tegra: avoid section mismatch warning
ARM: ks8695: fix section mismatch warning
ARM: pxa: avoid section mismatch warning
ARM: mmp: fix pxa168_device_usb_phy use on aspenite
ARM: mmp: fix timer_init calls
ARM: OMAP1: fix USB configuration for device-only setups
ARM: OMAP1: add MMC configuration for Palm Tungsten E
ARM: imx: fix dependencies on imx7ulp
ARM: meson: select HAVE_ARM_TWD and ARM_GLOBAL_TIMER
MAINTAINERS: add drivers/soc/amlogic/ to amlogic list
ARM: imx: add initial support for imx7ulp
ARM: debug-imx: only define DEBUG_IMX_UART_PORT if needed
ARM: dts: Fix OMAP4430 SDP Ethernet startup
ARM: dts: am335x-pdu001: Fix polarity of card detection input
ARM: OMAP1: ams-delta: Fix audio permanently muted
ARM: dts: omap5: Fix dual-role mode on Super-Speed port
arm64: dts: rockchip: fix rk3399-rockpro64 regulator gpios
ARM: davinci: da850-evm: remove unnecessary include
...
|
|
Samsung DTS ARM changes for v4.21, part 2
1. Add missing CPUs in cooling maps for Odroid X2 (missed in previous
round of fixups).
2. Fix clock configuration in audio subsystem on Odroid XU3/XU4.
* tag 'samsung-dt-4.21-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Specify I2S assigned clocks in proper node
ARM: dts: exynos: Add missing CPUs in cooling maps for Odroid X2
ARM: dts: exynos: remove display-port node from Arndale
ARM: dts: exynos: Add opp-suspend to DMC and leftbus devfreq OPPs on Exynos4
ARM: dts: s5pv210: Add s5p-jpeg codec node.
ARM: dts: exynos: Use Samsung SoC specific compatible for DWC2 module
ARM: dts: exynos: Add all CPUs in cooling maps
ARM: dts: exynos: Clarify comment explaining purpose of Odroid XU3 DTSI
ARM: dts: exynos: Add pin configuration for SD write protect on Odroid XU3/XU4/HC1
ARM: dts: exynos: Update maximum frequency for eMMC to 200MHz on Odroid XU3/XU4
ARM: dts: exynos: Update maximum frequency for SD card to 200MHz on Odroid XU3/XU4/HC1
ARM: dts: exynos: Fix LDO13 min values on Odroid XU3/XU4/HC1
ARM: dts: exynos: Add UHS-I bus speed support to Odroid XU3/XU4/HC1
ARM: dts: exynos: Add missing clocks to RTC node for Arndale board
ARM: dts: exynos: Add compatible for s5m8767 clocks node on Itop Core
ARM: dts: exynos: Add compatible for s2mps11 clocks node on Exynos542x
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add interrupt support for UART in RDA Micro RDA8810PL SoC.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add timer support for RDA Micro RDA8810PL SoC.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add initial devicetree for Orange Pi i96 board from Xunlong. It
is one of the 96Boards IoT Edition board.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
Arnd Bergmann
Thierry Reding
Tony Lindgren
Peter Ujfalusi
Thomas Petazzoni
Heiko Schocher
Arthur Demchenkov
Biju Das
Bartosz Golaszewski
Olof Johansson
Anson Huang
Sudeep Holla
Shawn Guo
Martin Blumenstingl
Carlo Caione
Linus Walleij
Jernej Skrabec
Chen-Yu Tsai
Aaro Koskinen
Johan Jonker
Linus Torvalds
Manivannan Sadhasivam