aboutsummaryrefslogtreecommitdiffstats
path: root/arch/arm/boot
AgeCommit message (Collapse)AuthorFilesLines
2021-08-03ARM: dts: am335x-evm: Enable PRU-ICSS moduleSuman Anna1-0/+4
The PRU-ICSS target module node was left in disabled state in the base am33xx-l4.dtsi file. PRU-ICSS is supported on the AM335x EVM, so enable this node on the AM335x EVM. The PRUSS node and most of its child nodes are already enabled in the base dts file, and so become effective automatically with the enabling of this PRU-ICSS target module node. The corresponding PRU nodes can be disabled later on if there are no use-cases defined to use a particular PRU core or the whole PRU-ICSS subsystem itself if both its PRU cores are unused. Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2021-08-03ARM: dts: am335x-bone-common: Enable PRU-ICSS nodeSuman Anna1-0/+4
The PRU-ICSS target module node was left in disabled state in the base am33xx-l4.dtsi file. Enable this node on all the AM335x beaglebone boards as they mostly use a AM3358 or a AM3359 SoC which do contain the PRU-ICSS IP. The PRUSS node and most of its child nodes are already enabled in the base dts file, and so become effective automatically with the enabling of this PRU-ICSS target-module node. The corresponding PRU nodes can be disabled later on if there are no use-cases defined to use a particular PRU core or the whole PRU-ICSS subsystem itself if both its PRU cores are unused. Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2021-08-03ARM: dts: am33xx-l4: Add PRUSS MDIO controller nodeSuman Anna1-0/+11
The PRUSS on AM335x SoCs has a MDIO sub-module that can be used to control external PHYs associated with the Industrial Ethernet peripherals within the PRUSS. The MDIO module used within the PRU-ICSS is an instance of the MDIO Controller used in TI Davinci SoCs. The same bus frequency of 1 MHz is chosen as the regular MDIO node. The node is added to the common am33xx-l4.dtsi file and is disabled. This needs to be enabled in the respective board files using the relevant AM335x SoCs supporting PRUSS and where the ethernet is pinned out and connected properly. Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2021-08-03ARM: dts: am33xx-l4: Add PRUSS nodeSuman Anna1-0/+71
Add the DT nodes for the PRU-ICSS on AM33xx family of SoCs. The AM33xx SoCs contain a single PRU-ICSS instance and is represented by a pruss node and other child nodes. PRU-ICSS is supported only on AM3356+ SoCs though in the AM33xx family, so the nodes are added under the corresponding disabled interconnect target module node in the common am33xx-l4 dtsi file. The target module node should be enabled in only those derivative board files that use a SoC containing PRU-ICSS. The PRUSS subsystem node contains the entire address space. The various sub-modules of the PRU-ICSS are represented as individual child nodes (so platform devices themselves) of the PRUSS subsystem node. These include the two PRU cores and the interrupt controller. All the Data RAMs are represented within a child node of its own named 'memories' without any compatible. The Real Time Media Independent Interface controller (MII_RT), and the CFG sub-module are represented as syscon nodes. The PRUSS CFG module has a clock mux for IEP clock, this clk node is added under the CFG child node 'clocks'. The default source for this mux clock is the PRU_ICSS_IEP_GCLK clock. The DT nodes use all standard properties. The regs property in the PRU nodes define the addresses for the Instruction RAM, the Debug and Control sub-modules for that PRU core. The firmware for each PRU core is defined through a 'firmware-name' property. The default names for the firmware images for each PRU core are defined as follows (these can be adjusted either in derivative board dts files or through sysfs at runtime if required): PRU-ICSS PRU0 Core: am335x-pru1_0-fw PRU-ICSS PRU1 Core: am335x-pru1_1-fw Note: 1. There are few more sub-modules like the Industrial Ethernet Peripheral (IEP), MDIO, UART, eCAP that do not have bindings and so will be added in the future. 2. The PRUSS INTC on AM335x SoCs also connect the host interrupts 0 to TSC_ADC; 6 and 7 as possible DMA events, so use the 'ti,irqs-reserved' property in derivative board dts files _if_ any of them should not be handled by the host OS. Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2021-08-03ARM: dts: aspeed-g5: Remove ngpios from sgpio node.Steven Lee1-1/+0
Remove ngpios property from sgpio node as it should be defined in the platform dts. Signed-off-by: Steven Lee <steven_lee@aspeedtech.com> Reviewed-by: Andrew Jeffery <andrew@aj.id.au> Link: https://lore.kernel.org/r/20210712100317.23298-5-steven_lee@aspeedtech.com Signed-off-by: Joel Stanley <joel@jms.id.au>
2021-08-03ARM: dts: aspeed-g6: Add SGPIO node.Steven Lee1-0/+28
AST2600 supports 2 SGPIO master interfaces one with 128 pins another one with 80 pins. Signed-off-by: Steven Lee <steven_lee@aspeedtech.com> Link: https://lore.kernel.org/r/20210712100317.23298-4-steven_lee@aspeedtech.com Signed-off-by: Joel Stanley <joel@jms.id.au>
2021-08-02Merge tag 'renesas-arm-dt-for-v5.15-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dtArnd Bergmann4-47/+9
Renesas ARM DT updates for v5.15 - Switches support for the Draak and Ebisu development boards, - I2C support on RZ/G2L, - I2C EEPROM support on the Ebisu development board, - Sound support for the R-Car D3 SoC and the Draak development board, - Support for the new R-Car H3e-2G and M3e-2G SoCs on the Salvator-XS and ULCB development boards, - IOMMU support for DMAC, EtherAVB, and SDHI on the R-Car M3-W+ SoC, - Miscellaneous fixes and improvements. * tag 'renesas-arm-dt-for-v5.15-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: (29 commits) arm64: dts: renesas: r8a77961: Add iommus to ipmmu_ds[01] related nodes arm64: dts: renesas: Add support for M3ULCB+Kingfisher with R-Car M3e-2G arm64: dts: renesas: Add support for M3ULCB with R-Car M3e-2G arm64: dts: renesas: Add support for Salvator-XS with R-Car M3e-2G arm64: dts: renesas: Add support for H3ULCB+Kingfisher with R-Car H3e-2G arm64: dts: renesas: Add support for H3ULCB with R-Car H3e-2G arm64: dts: renesas: Add support for Salvator-XS with R-Car H3e-2G arm64: dts: renesas: Add Renesas R8A779M3 SoC support arm64: dts: renesas: Add Renesas R8A779M1 SoC support arm64: dts: renesas: hihope-rzg2-ex: Add EtherAVB internal rx delay arm64: dts: renesas: r8a77995: draak: Add R-Car Sound support arm64: dts: renesas: r8a77995: Add R-Car Sound support arm64: dts: renesas: rcar-gen3: Add SoC model to comment headers arm64: dts: renesas: r8a77990: ebisu: Add I2C EEPROM for PMIC arm64: dts: renesas: r8a77995: draak: Remove bogus adv7511w properties arm64: dts: renesas: beacon: Enable micbias arm64: dts: renesas: r9a07g044: Add I2C nodes arm64: dts: renesas: r8a779a0: Restore sort order arm64: dts: renesas: r8a77990: ebisu: Add SW4 support arm64: dts: renesas: r8a77995: draak: Add SW56 support ... Link: https://lore.kernel.org/r/cover.1627650696.git.geert+renesas@glider.be Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-08-02ARM: dts: owl-s500-roseapplepi: Add ethernet supportCristian Ciocaltea1-0/+45
Add pinctrl configuration for enabling the Ethernet MAC on RoseapplePi SBC. Additionally, provide the necessary properties for the generic S500 ethernet node in order to setup PHY and MDIO. Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com> Signed-off-by: Manivannan Sadhasivam <mani@kernel.org> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Link: https://lore.kernel.org/r/d0e1fbf81984127f0352eb740c7129424b5e40f9.1623401998.git.cristian.ciocaltea@gmail.com Link: https://lore.kernel.org/r/20210628072817.8269-3-mani@kernel.org' Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-08-02ARM: dts: owl-s500: Add ethernet supportCristian Ciocaltea1-0/+10
Add Ethernet MAC device tree node for Actions Semi S500 SoC. Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com> Signed-off-by: Manivannan Sadhasivam <mani@kernel.org> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Link: https://lore.kernel.org/r/222ee0c2cb431619f558dce9726585ac92f65e00.1623401998.git.cristian.ciocaltea@gmail.com Link: https://lore.kernel.org/r/20210628072817.8269-2-mani@kernel.org' Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-08-02Merge tag 'stm32-dt-for-v5.14-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/fixesArnd Bergmann2-11/+18
STM32 DT fixes for v5.14, round 1 Highlights: ----------- -Fixes are for DHCOM/DHCOR boards: - Set HW RTC ad default RTC - Disable EDPD LAN8710 feature as it is not a stable feature. - Fix touchscreen IRQ line assignment * tag 'stm32-dt-for-v5.14-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: ARM: dts: stm32: Fix touchscreen IRQ line assignment on DHCOM ARM: dts: stm32: Disable LAN8710 EDPD on DHCOM ARM: dts: stm32: Prefer HW RTC on DHCOM SoM Link: https://lore.kernel.org/r/c0b6031b-2de7-2ef8-71b2-a0af8f475932@foss.st.com Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-08-02Merge tag 'imx-fixes-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixesArnd Bergmann3-3/+10
i.MX fixes for 5.14: - A couple of fixes on MMDC driver to add missing iounmap() and clk_disable_unprepare(), and a follow-up fix. - Fix missing-prototypes warning in SRC driver. - Revert commit 7d981405d0fd ("soc: imx8m: change to use platform driver"), which breaks i.MX8M system that has CAAM driver enabled. - One fix on imx53-m53menlo pinctrl configuration. - Increase the PHY reset duration for imx6qdl-sr-som to fix intermittent issues where the PHY would be unresponsive every once in a while. - Add missing flag for in-band signalling between PHY and MAC on kontron-sl28-var2 board to fix network support. - Limit the SDIO Clock on Colibri iMX6ULL to 25MHz for fixing wireless noise issue. - Fix sysclk node name for LS1028A so that U-Boot is able to update the "clock-frequency" property. * tag 'imx-fixes-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: ARM: dts: imx: Swap M53Menlo pinctrl_power_button/pinctrl_power_out pins ARM: imx: fix missing 3rd argument in macro imx_mmdc_perf_init ARM: dts: colibri-imx6ull: limit SDIO clock to 25MHz arm64: dts: ls1028: sl28: fix networking for variant 2 Revert "soc: imx8m: change to use platform driver" ARM: dts: imx6qdl-sr-som: Increase the PHY reset duration to 10ms ARM: imx: common: Move prototype outside the SMP block ARM: imx: add missing clk_disable_unprepare() ARM: imx: add missing iounmap() arm64: dts: ls1028a: fix node name for the sysclk Link: https://lore.kernel.org/r/20210726023221.GF5901@dragon Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-08-02ARM: dts: nomadik: Fix up interrupt controller node namesSudeep Holla1-2/+2
Once the new schema interrupt-controller/arm,vic.yaml is added, we get the below warnings: arch/arm/boot/dts/ste-nomadik-nhk15.dt.yaml: intc@10140000: $nodename:0: 'intc@10140000' does not match '^interrupt-controller(@[0-9a-f,]+)*$' Fix the node names for the interrupt controller to conform to the standard node name interrupt-controller@.. Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Cc: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20210617210825.3064367-2-sudeep.holla@arm.com Link: https://lore.kernel.org/r/20210626000103.830184-1-linus.walleij@linaro.org' Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-08-02ARM: dts: at91: use the right property for shutdown controllerNicolas Ferre7-7/+7
The wrong property "atmel,shdwc-debouncer" was used to specify the debounce delay for the shutdown controler. Replace it with the documented and implemented property "debounce-delay-us", as mentioned in v4 driver submission. See: https://lore.kernel.org/r/1458134390-23847-3-git-send-email-nicolas.ferre@atmel.com/ Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Reported-by: Clément Léger <clement.leger@bootlin.com> Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com> Link: https://lore.kernel.org/r/20210730172729.28093-1-nicolas.ferre@microchip.com/
2021-08-02ARM: dts: ux500: Adjust operating points to realityLinus Walleij4-13/+22
The operating points should correspond to the actual frequencies supported for the CPU. Other patches have fixed so these are rounded and reported properly, this fixes the device trees to match. The Codina variant has a lower frequency than other devices so indicate this in the device tree. Cc: phone-devel@vger.kernel.org Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2021-07-30ARM: dts: stm32: Update AV96 adv7513 node per dtbs_checkMarek Vasut1-4/+2
Swap reg and reg-names order and drop adi,input-justification and adi,input-style to fix the following dtbs_check warnings: arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dt.yaml: hdmi-transmitter@3d: adi,input-justification: False schema does not allow ['evenly'] arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dt.yaml: hdmi-transmitter@3d: adi,input-style: False schema does not allow [[1]] arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dt.yaml: hdmi-transmitter@3d: reg-names:1: 'edid' was expected arch/arm/boot/dts/stm32mp157a-dhcor-avenger96.dt.yaml: hdmi-transmitter@3d: reg-names:2: 'cec' was expected Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Cc: linux-stm32@st-md-mailman.stormreply.com To: linux-arm-kernel@lists.infradead.org Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2021-07-30ARM: dts: stm32: Set {bitclock,frame}-master phandles on ST DKxMarek Vasut1-4/+4
Fix the following dtbs_check warning: cs42l51@4a: port:endpoint@0:frame-master: True is not of type 'array' cs42l51@4a: port:endpoint@0:bitclock-master: True is not of type 'array' Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Cc: linux-stm32@st-md-mailman.stormreply.com To: linux-arm-kernel@lists.infradead.org Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2021-07-30ARM: dts: stm32: Add coprocessor detach mbox on stm32mp15x-dkx boardsArnaud Pouliquen1-2/+2
To support the detach feature, add a new mailbox channel to inform the remote processor on a detach. This signal allows the remote processor firmware to stop IPC communication and to reinitialize the resources for a re-attach. Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2021-07-30ARM: dts: stm32: Add coprocessor detach mbox on stm32mp157c-ed1 boardArnaud Pouliquen1-2/+2
To support the detach feature, add a new mailbox channel to inform the remote processor on a detach. This signal allows the remote processor firmware to stop IPC communication and to reinitialize the resources for a re-attach. Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2021-07-30ARM: dts: stm32: Add usbphyc_port1 supply on DHCOM SoMMarek Vasut1-0/+4
The port is unused, but shares the same supply with port0, so fill the DT property in. This fixes the following dtbs_check warning: arch/arm/boot/dts/stm32mp153c-dhcom-drc02.dt.yaml: usbphyc@5a006000: usb-phy@1: 'phy-supply' is a required property Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Cc: kernel@dh-electronics.com Cc: linux-stm32@st-md-mailman.stormreply.com To: linux-arm-kernel@lists.infradead.org Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2021-07-30ARM: dts: stm32: Add backlight and panel supply on DHCOM SoMMarek Vasut1-0/+17
Fix the following dtbs_check warning: arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dt.yaml: display-bl: 'power-supply' is a required property arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dt.yaml: panel: 'power-supply' is a required property Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Cc: kernel@dh-electronics.com Cc: linux-stm32@st-md-mailman.stormreply.com To: linux-arm-kernel@lists.infradead.org Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2021-07-30ARM: dts: stm32: Set {bitclock,frame}-master phandles on DHCOM SoMMarek Vasut1-4/+4
Fix the following dtbs_check warning: arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dt.yaml: codec@a: port:endpoint@0:frame-master: True is not of type 'array' arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dt.yaml: codec@a: port:endpoint@0:bitclock-master: True is not of type 'array' Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Cc: kernel@dh-electronics.com Cc: linux-stm32@st-md-mailman.stormreply.com To: linux-arm-kernel@lists.infradead.org Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2021-07-30ARM: dts: stm32: Fix touchscreen IRQ line assignment on DHCOMMarek Vasut1-10/+14
While 7e5f3155dcbb4 ("ARM: dts: stm32: Fix LED5 on STM32MP1 DHCOM PDK2") fixed the LED0 assignment on the PDK2 board, the same commit did not update the touchscreen IRQ line assignment, which is the same GPIO line, shared between the LED0 output and touchscreen IRQ input. To make this more convoluted, the same EXTI input (not the same GPIO line) is shared between Button B which is Active-Low IRQ, and touchscreen IRQ which is Edge-Falling IRQ, which cannot be used at the same time. In case the LCD board with touchscreen is in use, which is the case here, LED0 must be disabled, Button B must be polled, so the touchscreen interrupt works as it should. Update the touchscreen IRQ line assignment, disable LED0 and use polled GPIO button driver for Button B, since the DT here describes baseboard with LCD board. Fixes: 7e5f3155dcbb4 ("ARM: dts: stm32: Fix LED5 on STM32MP1 DHCOM PDK2") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Cc: linux-stm32@st-md-mailman.stormreply.com To: linux-arm-kernel@lists.infradead.org Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2021-07-30ARM: dts: stm32: Disable LAN8710 EDPD on DHCOMMarek Vasut1-0/+1
The LAN8710 Energy Detect Power Down (EDPD) functionality might cause unreliable cable detection. There are multiple accounts of this in the SMSC PHY driver patches which attempted to make EDPD reliable, however it seems there is always some sort of corner case left. Unfortunatelly, there is no errata documented which would confirm this to be a silicon bug on the LAN87xx series of PHYs (LAN8700, LAN8710, LAN8720 at least). Disable EDPD on the DHCOM SoM, just like multiple other boards already do as well, to make the cable detection reliable. Fixes: 34e0c7847dcf ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Cc: linux-stm32@st-md-mailman.stormreply.com To: linux-arm-kernel@lists.infradead.org Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2021-07-30ARM: dts: stm32: Prefer HW RTC on DHCOM SoMMarek Vasut1-1/+3
The DHCOM SoM has two RTC, one is the STM32 RTC built into the SoC and another is Microcrystal RV RTC. By default, only the later has battery backup, the former does not. The order in which the RTCs are probed on boot is random, which means the kernel might pick up system time from the STM32 RTC which has no battery backup. This then leads to incorrect initial system time setup, even though the HW RTC has correct time configured in it. Add DT alias entries, so that the RTCs get assigned fixed IDs and the HW RTC is always picked by the kernel as the default RTC, thus resulting in correct system time in early userspace. Fixes: 34e0c7847dcf ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Cc: linux-stm32@st-md-mailman.stormreply.com To: linux-arm-kernel@lists.infradead.org Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2021-07-30ARM: dts: ux500: Add a device tree for KyleLinus Walleij2-1/+666
This adds a basic device tree for the Samsung SGH-I407 mobile phone also known as Kyle. Cc: newbyte@disroot.org Cc: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2021-07-30ARM: dts: ux500: Add devicetree for CodinaLinus Walleij2-0/+852
This adds a devicetree for Samsung GT-I8160 also known as Codina. Cc: newbyte@disroot.org Cc: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2021-07-30ARM: dts: ux500: ab8500: Link USB PHY to USB controller nodeStephan Gerhold2-1/+13
At the moment the AB8500 USB PHY driver still uses the old USB PHY subsystem instead of the generic PHY subsystem. This means that there is no explicit link between the USB controller and the USB PHY. In U-Boot the PHY driver is integrated in the generic PHY subsystem, so we need to use the typical PHY device tree bindings to specify which PHY belongs to the USB controller. Add the link between USB controller and PHY to both ste-ab8500.dtsi and ste-ab8505.dtsi. This is mainly for U-Boot for now and will just be ignored in Linux. However, if the AB8500 USB PHY driver in Linux is moved to the generic PHY subsystem at some point these device tree changes can be used as well. Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2021-07-30ARM: dts: ux500: Flag eMMCs as non-SDIO/SDLinus Walleij6-0/+14
We use the no-sdio and no-sd flags to indicate that these eMMCs are neither, so that the operating system can skip trying to identify them as SDIO or SD during boot, which just takes time. Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2021-07-30ARM: dts: ux500: Add device tree for Samsung GaviniLinus Walleij3-0/+871
This adds a device tree for the Samsung Galaxy Beam GT-I8530 also known as Gavini. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2021-07-28ARM: dts: aspeed: ast2500evb: Enable built in RTCJoel Stanley1-0/+4
Enable this device so the RTC driver can be tested on the EVB. Signed-off-by: Joel Stanley <joel@jms.id.au> Link: https://lore.kernel.org/r/20210727034639.474458-1-joel@jms.id.au
2021-07-28ARM: dts: aspeed: tacoma: Add TPM reset GPIOJoel Stanley1-1/+1
The GPIO is used to place the BMC-connected TPM in reset. The net is called BMC_TPM_RST_N on Tacoma. Signed-off-by: Joel Stanley <joel@jms.id.au> Reviewed-by: Andrew Jeffery <andrew@aj.id.au> Link: https://lore.kernel.org/r/20210727033319.473152-3-joel@jms.id.au
2021-07-28ARM: dts: rainier, everest: Add TPM reset GPIOJoel Stanley2-2/+2
The GPIO is used to place the BMC-connected TPM in reset. This state is latched until the BMC is next reset, blocking access to the TPM for that boot. On both machines this net is called TPM_RESET_LATCH_B. Signed-off-by: Joel Stanley <joel@jms.id.au> Reviewed-by: Andrew Jeffery <andrew@aj.id.au> Link: https://lore.kernel.org/r/20210727033319.473152-2-joel@jms.id.au
2021-07-27ARM: dts: at91: sama5d2_icp: enable digital filter for I2C nodesCodrin Ciubotariu1-0/+6
SAMA5D2's I2C controller supports digital filter, so let's enable it. Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Link: https://lore.kernel.org/r/20210727134115.1353494-1-codrin.ciubotariu@microchip.com
2021-07-27ARM: dts: at91: sama5d4_xplained: change the key code of the gpio keyLudovic Desroches1-1/+2
Having a button code and not a key code causes issues with libinput. udev won't set ID_INPUT_KEY. If it is forced, then it causes a bug within libinput. Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Link: https://lore.kernel.org/r/20210727091351.44475-1-nicolas.ferre@microchip.com
2021-07-27ARM: dts: at91: add conflict note for d3Claudiu Beznea1-1/+1
Pin feeding d3 led may be in conflict with EBI CS0, USART2 CTS. Add a note for this. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Link: https://lore.kernel.org/r/20210727074006.1609989-2-claudiu.beznea@microchip.com
2021-07-27ARM: dts: at91: add pinctrl-{names, 0} for all gpiosClaudiu Beznea3-1/+63
Add pinctrl-names and pinctrl-0 properties on controllers that claims to use pins to avoid failures due to commit 2ab73c6d8323 ("gpio: Support GPIO controllers without pin-ranges") and also to avoid using pins that may be claimed my other IPs. Fixes: b7c2b6157079 ("ARM: at91: add Atmel's SAMA5D3 Xplained board") Fixes: 1e5f532c2737 ("ARM: dts: at91: sam9x60: add device tree for soc and board") Fixes: 38153a017896 ("ARM: at91/dt: sama5d4: add dts for sama5d4 xplained board") Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Link: https://lore.kernel.org/r/20210727074006.1609989-1-claudiu.beznea@microchip.com Cc: <stable@vger.kernel.org> # v5.7+
2021-07-27ARM: dts: am335x-sancloud-bbe-lite: New devicetreePaul Barker2-0/+51
This adds support for the Sancloud BBE Lite which shares a common hardware base with the non-Lite version of the BBE. Signed-off-by: Paul Barker <paul.barker@sancloud.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2021-07-27ARM: dts: am335x-sancloud-bbe: Extract common codePaul Barker2-90/+97
The Sancloud BBE, BBE Lite and BBE Extended+WiFi share a common hardware base so we can avoid duplication via a dtsi file. Signed-off-by: Paul Barker <paul.barker@sancloud.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2021-07-27ARM: dts: am335x-boneblack: Extract HDMI configPaul Barker5-135/+144
Move the HDMI hardware configuration for the BeagleBone Black out of the boneblack common dtsi file and into its own separate dtsi file. This allows the devicetree for BeagleBone Black derivatives which lack the hdmi encoding hardware to include the common dtsi file without needing to duplicate configuration or override the status of all hdmi-related nodes. Signed-off-by: Paul Barker <paul.barker@sancloud.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2021-07-27ARM: dts: at91: sama5d27_som1_ek: enable ADC nodeEugen Hristev1-1/+3
Enable the ADC for AN pins on Mikrobus1 and Mikrobus2 on the board. These correspond to channels AD6 and AD7 in the controller. # cat /sys/bus/iio/devices/iio\:device0/in_voltage6_raw 240 # cat /sys/bus/iio/devices/iio\:device0/in_voltage7_raw 16380 Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Link: https://lore.kernel.org/r/20210622101742.14535-1-eugen.hristev@microchip.com
2021-07-27ARM: dts: omap4-l4-abe: Add McASP configurationPeter Ujfalusi1-16/+19
OMAP4 has a single McASP instance with single serializer and locked for DIT mode. To be able to enable the support the following fixes needed: - Add the DAT port ranges to the target module's ranges We can already fill in the op-mode and serial-dir for McASP as it only supports this configuration, but keep the module disabled as there is no known device available where it is used. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2021-07-27ARM: dts: omap4-l4-abe: Correct sidle modes for McASPPeter Ujfalusi1-2/+1
McASP only supports Force-idle, No-idle and Smart-idle modes Signed-off-by: Peter Ujfalusi <peter.ujfalusi@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2021-07-27ARM: dts: Add support for dra762 abz packageLokesh Vutla4-21/+28
dra762 abz package is pin compatible with dra742 and few peripherals like DDR with upgraded speed. Add dt support for this SoC. Reported-by: Praneeth Bajjuri <praneeth@ti.com> Tested-by: Praneeth Bajjuri <praneeth@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> [khilman: forward port from ti-linux-5.4.y] Signed-off-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2021-07-27ARM: dts: am335x-boneblue: add gpio-line-namesDavid Lechner1-1/+142
This adds gpio-line-names to the BeagleBone Blue DTS. The line names are based on the BeagleBone Blue rev A2 schematic. Signed-off-by: David Lechner <david@lechnology.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2021-07-27omap5-board-common: remove not physically existing vdds_1v8_main fixed-regulatorH. Nikolaus Schaller1-8/+1
This device tree include file describes a fixed-regulator connecting smps7_reg output (1.8V) to some 1.8V rail and consumers (vdds_1v8_main). This regulator does not physically exist. I assume it was introduced as a wrapper around smps7_reg to provide a speaking signal name "vdds_1v8_main" as label. This fixed-regulator without real function was not an issue in driver code until Commit 98e48cd9283d ("regulator: core: resolve supply for boot-on/always-on regulators") introduced a new check for regulator initialization which makes Palmas regulator registration fail: [ 5.407712] ldo1: supplied by vsys_cobra [ 5.412748] ldo2: supplied by vsys_cobra [ 5.417603] palmas-pmic 48070000.i2c:palmas@48:palmas_pmic: failed to register 48070000.i2c:palmas@48:palmas_pmic regulator The reason is that the supply-chain of regulators is too long and goes from ldo3 through the virtual vdds_1v8_main regulator and then back to smps7. This adds a cross-dependency of probing Palmas regulators and the fixed-regulator which leads to probe deferral by the new check and is no longer resolved. Since we do not control what device tree files including this one reference (either &vdds_1v8_main or &smps7_reg or both) we keep both labels for smps7 for compatibility. Fixes: 98e48cd9283d ("regulator: core: resolve supply for boot-on/always-on regulators") Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2021-07-27ARM: dts: am437x-l4: fix typo in can@0 nodeDario Binacchi1-1/+1
Replace clock-name with clock-names. Fixes: 2a4117df9b43 ("ARM: dts: Fix dcan driver probe failed on am437x platform") Signed-off-by: Dario Binacchi <dariobin@libero.it> Signed-off-by: Tony Lindgren <tony@atomide.com>
2021-07-27ARM: dts: am43x-epos-evm: Reduce i2c0 bus speed for tps65218Dave Gerlach1-1/+1
Based on the latest timing specifications for the TPS65218 from the data sheet, http://www.ti.com/lit/ds/symlink/tps65218.pdf, document SLDS206 from November 2014, we must change the i2c bus speed to better fit within the minimum high SCL time required for proper i2c transfer. When running at 400khz, measurements show that SCL spends 0.8125 uS/1.666 uS high/low which violates the requirement for minimum high period of SCL provided in datasheet Table 7.6 which is 1 uS. Switching to 100khz gives us 5 uS/5 uS high/low which both fall above the minimum given values for 100 khz, 4.0 uS/4.7 uS high/low. Without this patch occasionally a voltage set operation from the kernel will appear to have worked but the actual voltage reflected on the PMIC will not have updated, causing problems especially with cpufreq that may update to a higher OPP without actually raising the voltage on DCDC2, leading to a hang. Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2021-07-26ARM: dts: meson8b: ec100: Fix the pwm regulator supply propertiesAnand Moon1-2/+2
After enabling CONFIG_REGULATOR_DEBUG=y we observer below debug logs. Changes help link VCCK and VDDEE pwm regulator to 5V regulator supply instead of dummy regulator. [ 7.117140] pwm-regulator regulator-vcck: Looking up pwm-supply from device tree [ 7.117153] pwm-regulator regulator-vcck: Looking up pwm-supply property in node /regulator-vcck failed [ 7.117184] VCCK: supplied by regulator-dummy [ 7.117194] regulator-dummy: could not add device link regulator.8: -ENOENT [ 7.117266] VCCK: 860 <--> 1140 mV at 986 mV, enabled [ 7.118498] VDDEE: will resolve supply early: pwm [ 7.118515] pwm-regulator regulator-vddee: Looking up pwm-supply from device tree [ 7.118526] pwm-regulator regulator-vddee: Looking up pwm-supply property in node /regulator-vddee failed [ 7.118553] VDDEE: supplied by regulator-dummy [ 7.118563] regulator-dummy: could not add device link regulator.9: -ENOENT Fixes: 087a1d8b4e4c ("ARM: dts: meson8b: ec100: add the VDDEE regulator") Fixes: 3e7db1c1b7a3 ("ARM: dts: meson8b: ec100: improve the description of the regulators") Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Anand Moon <linux.amoon@gmail.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://lore.kernel.org/r/20210705112358.3554-4-linux.amoon@gmail.com
2021-07-26ARM: dts: meson8b: mxq: Fix the pwm regulator supply propertiesAnand Moon1-1/+3
After enabling CONFIG_REGULATOR_DEBUG=y we observer below debug logs. Changes help link VCCK and VDDEE pwm regulator to 5V regulator supply instead of dummy regulator. Add missing pwm-supply for regulator-vcck regulator node. [ 7.117140] pwm-regulator regulator-vcck: Looking up pwm-supply from device tree [ 7.117153] pwm-regulator regulator-vcck: Looking up pwm-supply property in node /regulator-vcck failed [ 7.117184] VCCK: supplied by regulator-dummy [ 7.117194] regulator-dummy: could not add device link regulator.8: -ENOENT [ 7.117266] VCCK: 860 <--> 1140 mV at 986 mV, enabled [ 7.118498] VDDEE: will resolve supply early: pwm [ 7.118515] pwm-regulator regulator-vddee: Looking up pwm-supply from device tree [ 7.118526] pwm-regulator regulator-vddee: Looking up pwm-supply property in node /regulator-vddee failed [ 7.118553] VDDEE: supplied by regulator-dummy [ 7.118563] regulator-dummy: could not add device link regulator.9: -ENOENT Fixes: dee51cd0d2e8 ("ARM: dts: meson8b: mxq: add the VDDEE regulator") Fixes: d94f60e3dfa0 ("ARM: dts: meson8b: mxq: improve support for the TRONFY MXQ S805") Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Anand Moon <linux.amoon@gmail.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://lore.kernel.org/r/20210705112358.3554-3-linux.amoon@gmail.com
2021-07-26ARM: dts: meson8b: odroidc1: Fix the pwm regulator supply propertiesAnand Moon1-2/+2
After enabling CONFIG_REGULATOR_DEBUG=y we observe below debug logs. Changes help link VCCK and VDDEE pwm regulator to 5V regulator supply instead of dummy regulator. [ 7.117140] pwm-regulator regulator-vcck: Looking up pwm-supply from device tree [ 7.117153] pwm-regulator regulator-vcck: Looking up pwm-supply property in node /regulator-vcck failed [ 7.117184] VCCK: supplied by regulator-dummy [ 7.117194] regulator-dummy: could not add device link regulator.8: -ENOENT [ 7.117266] VCCK: 860 <--> 1140 mV at 986 mV, enabled [ 7.118498] VDDEE: will resolve supply early: pwm [ 7.118515] pwm-regulator regulator-vddee: Looking up pwm-supply from device tree [ 7.118526] pwm-regulator regulator-vddee: Looking up pwm-supply property in node /regulator-vddee failed [ 7.118553] VDDEE: supplied by regulator-dummy [ 7.118563] regulator-dummy: could not add device link regulator.9: -ENOENT Fixes: 524d96083b66 ("ARM: dts: meson8b: odroidc1: add the CPU voltage regulator") Fixes: 8bdf38be712d ("ARM: dts: meson8b: odroidc1: add the VDDEE regulator") Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Anand Moon <linux.amoon@gmail.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> [narmstrong: fixed typo in commit s/observer/observe/] Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://lore.kernel.org/r/20210705112358.3554-2-linux.amoon@gmail.com
Copyright © 1996 – 2026 Jason A. Donenfeld. All Rights Reverse Engineered.