aboutsummaryrefslogtreecommitdiffstats
path: root/arch/arm/boot
AgeCommit message (Collapse)AuthorFilesLines
2021-05-31ARM: tegra: acer-a500: Specify proper voltage for WiFi SDIO busDmitry Osipenko1-1/+1
Tegra20 has v2.00 SDMMC controller which doesn't support voltage switching and the WiFi SDIO bus voltage is fixed to 1.8v in accordance to the board's schematics, while MMC core confusingly saying that it's 3.3v because of the v2.00. Let's correct the voltage in the device-tree just for consistency. This is a minor improvement which doesn't fix any problems. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2021-05-31ARM: tegra: acer-a500: Improve microphone detectionDmitry Osipenko1-1/+4
Use edge-triggered interrupt and set delay to 100ms for microphone hook detection. This doesn't fix any known problems, but there is a smaller chance to miss insertion of the microphone now, which previously happened rarely. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2021-05-31ARM: dts: silk: Configure pull-up for SOFT_SW GPIO keysGeert Uytterhoeven1-1/+9
The GPIO pins connected to the 4 Software Switches ("SOFT_SW", SW12) do not have external pull-up resistors, but rely on internal pull-ups being enabled. Fortunately this is satisfied by the initial state of these pins. Make this explicit by enabling bias-pull-up, to remove the dependency on initial state and/or boot loader configuration. While at it, rename the surrounding device node from "gpio-keys" to "keyboard", to comply with generic node name recommendations. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/45f38a5333feba9bea80efeb5a41a6c3f60deda2.1619785905.git.geert+renesas@glider.be
2021-05-31ARM: dts: gose: Configure pull-up for SOFT_SW GPIO keysGeert Uytterhoeven1-1/+9
The GPIO pins connected to the 4 Software Switches ("SOFT_SW", SW2) do not have external pull-up resistors, but rely on internal pull-ups being enabled. Fortunately this is satisfied by the initial state of these pins. Make this explicit by enabling bias-pull-up, to remove the dependency on initial state and/or boot loader configuration. While at it, rename the surrounding device node from "gpio-keys" to "keyboard", to comply with generic node name recommendations. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/1cdec892b1491309b12bdaf7bc8428b3a19b1ed5.1619785905.git.geert+renesas@glider.be
2021-05-31ARM: dts: blanche: Configure pull-up for SOFT_SW and SW25 GPIO keysGeert Uytterhoeven1-0/+8
The GPIO pins connected to the 4 Software Switches (SW2) and the second Tact Switch (SW25) do not have external pull-up resistors, but rely on internal pull-ups being enabled. Fortunately this is satisfied by the initial state of these pins. Make this explicit by enabling bias-pull-up, to remove the dependency on initial state and/or boot loader configuration. Note that the GPIO pin connected to the first Tact Switch (SW24) does have an external pull-up resistor. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/011e4c461767f2dd690b655b3dd501eb554184c1.1619785905.git.geert+renesas@glider.be
2021-05-31ARM: dts: lager: Configure pull-up for SOFT_SW GPIO keysGeert Uytterhoeven1-0/+8
The GPIO pins connected to the 4 Software Switches (SW2) do not have external pull-up resistors, but rely on internal pull-ups being enabled. Fortunately this is satisfied by the initial state of these pins. Make this explicit by enabling bias-pull-up, to remove the dependency on initial state and/or boot loader configuration. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Link: https://lore.kernel.org/r/9fae3c0c2c0000f6b43c9ce87fe64a594b30a7da.1619785905.git.geert+renesas@glider.be
2021-05-29ARM: dts: qcom: sdx55-telit: Represent secure-regions as 64-bit elementsManivannan Sadhasivam1-2/+2
The corresponding MTD code expects the regions to be of 64-bit elements. Hence, prefix "/bits/ 64", otherwise the regions will not be parsed correctly. Fixes: 6a5d3c611930 ("ARM: dts: qcom: sdx55: Add basic devicetree support for Telit FN980 TLB") Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Link: https://lore.kernel.org/r/20210512050141.43338-2-manivannan.sadhasivam@linaro.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2021-05-29ARM: dts: qcom: sdx55-t55: Represent secure-regions as 64-bit elementsManivannan Sadhasivam1-1/+1
The corresponding MTD code expects the regions to be of 64-bit elements. Hence, prefix "/bits/ 64", otherwise the regions will not be parsed correctly. Fixes: 3263d4be5788 ("ARM: dts: qcom: sdx55: Add basic devicetree support for Thundercomm T55") Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Link: https://lore.kernel.org/r/20210512050141.43338-1-manivannan.sadhasivam@linaro.org Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2021-05-28ARM: dts: rockchip: move mmc aliases to board dts on rk3066/rk3188Johan Jonker8-3/+35
As suggested by Arnd Bergmann, the newly added mmc aliases should be board specific, so move them from the general dtsi to the individual boards. Suggested-by: Arnd Bergmann <arnd@kernel.org> Signed-off-by: Johan Jonker <jbx6244@gmail.com> Link: https://lore.kernel.org/r/20210520091822.28491-1-jbx6244@gmail.com Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2021-05-27ARM: dts: alt: Add SW2 as GPIO keysWolfram Sang1-0/+42
SW2 on Alt is connected as on Lager board. So, use the same GPIO settings. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Link: https://lore.kernel.org/r/20210525091512.29119-1-wsa+renesas@sang-engineering.com Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2021-05-27ARM: dts: OMAP2+: Replace underscores in sub-mailbox node namesSuman Anna8-20/+20
A number of sub-mailbox node names in various OMAP2+ dts files are currently using underscores. This is not adhering to the node name convention, fix all of these to use hiphens. These nodes are already using the prefix mbox, so they will be in compliance with the sub-mailbox node name convention being added in the OMAP Mailbox YAML binding as well. Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2021-05-27ARM: dts: AM33xx/AM43xx: Rename wkup_m3 sub-mailbox nodeSuman Anna2-2/+2
The OMAP sub-mailbox used to communicate with the Wakeup M3 remote processor is currently named wkup_m3. This name can be confused with the remote processor node. So, rename this to mbox-wkup-m3 to remove the ambiguity and to also adhere to the sub-mailbox node name convention being added in the OMAP Mailbox YAML binding. Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2021-05-27ARM: dts: OMAP2/OMAP3: Rename processor sub-mailbox nodesSuman Anna3-4/+4
The OMAP sub-mailbox used to communicate with the DSP and IVA remote processors are currently named after the processor name. These can be confused with the remote processors themselves. Rename them to remove the ambiguity and use the prefix mbox to also adhere to the sub-mailbox node name convention being added in the OMAP Mailbox YAML binding. Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2021-05-27ARM: dts: OMAP2420: Drop interrupt-names from mailbox nodeSuman Anna1-1/+0
The interrupt-names property is neither defined nor used in either of the OMAP Mailbox binding or the driver. So, drop them. This is in preparation for converting the OMAP Mailbox binding to YAML format. Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2021-05-27ARM: dts: am437x-l4: Drop ti,omap2-uart entry from UART nodesVignesh Raghavendra1-6/+6
ti,omap2-uart was kept around to work with legacy omap-serial driver. Now that we have completed move to 8250-omap.c drop legacy compatible. This will simplify writing YAML schema. Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2021-05-27ARM: dts: dra7-l4: Drop ti,omap4-uart entry from UART nodesVignesh Raghavendra1-10/+10
ti,omap4-uart was kept around to work with legacy omap-serial driver. Now that we have completed move to 8250-omap.c drop legacy compatible. This will simplify writing YAML schema. Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2021-05-27ARM: dts: am335x: fix ti,no-reset-on-init flag for gpiosGrygorii Strashko5-6/+6
The ti,no-reset-on-init flag need to be at the interconnect target module level for the modules that have it defined. The ti-sysc driver handles this case, but produces warning, not a critical issue. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2021-05-27ARM: dts: am437x-gp-evm: fix ti,no-reset-on-init flag for gpiosGrygorii Strashko2-2/+5
The ti,no-reset-on-init flag need to be at the interconnect target module level for the modules that have it defined. The ti-sysc driver handles this case, but produces warning, not a critical issue. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2021-05-27ARM: dts: am57xx-cl-som-am57x: fix ti,no-reset-on-init flag for gpiosGrygorii Strashko2-5/+4
The ti,no-reset-on-init flag need to be at the interconnect target module level for the modules that have it defined. The ti-sysc driver handles this case, but produces warning, not a critical issue. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2021-05-27ARM: dts: dra7x-evm: Align GPIO hog names with dt-schemaGeert Uytterhoeven4-4/+4
The dt-schema for nxp,pcf8575 expects GPIO hogs node names to end with a 'hog' suffix. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2021-05-27ARM: dts: omap5-board-common: align gpio hog names with dt-schemaGrygorii Strashko1-1/+1
The GPIO Hog dt-schema node naming convention expect GPIO hogs node names to end with a 'hog' suffix. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2021-05-27ARM: dts: omap3: align gpio hog names with dt-schemaGrygorii Strashko2-2/+2
The GPIO Hog dt-schema node naming convention expect GPIO hogs node names to end with a 'hog' suffix. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2021-05-27ARM: dts: am437x: align gpio hog names with dt-schemaGrygorii Strashko2-3/+3
The GPIO Hog dt-schema node naming convention expect GPIO hogs node names to end with a 'hog' suffix. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2021-05-27ARM: dts: am335x: align GPIO hog names with dt-schemaGrygorii Strashko5-10/+10
The GPIO Hog dt-schema node naming convention expect GPIO hogs node names to end with a 'hog' suffix. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2021-05-25ARM: dts: renesas: Move enable-method to CPU nodesGeert Uytterhoeven10-10/+28
According to Documentation/devicetree/bindings/arm/cpus.yaml, the "enable-method" property should be a property of the individual CPU nodes, and not of the parent "cpus" container node. However, on R-Car Gen2 and RZ/G1 SoCs, the property is tied to the "cpus" node instead. Secondary CPU bringup and CPU hot (un)plug work regardless, as arm_dt_init_cpu_maps() falls back to looking in the "cpus" node. The cpuidle code does not have such a fallback, so it does not detect the enable-method. Note that cpuidle does not support the "renesas,apmu" enable-method yet, so for now this does not make any difference. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/35fcfedf9de9269185c48ca5a6dfcba7cdd3484b.1621427319.git.geert+renesas@glider.be
2021-05-25ARM: dts: rcar-gen1: Correct internal delay for i2c[123]Geert Uytterhoeven2-0/+6
According to the R-Car M1A and H1 Hardware User's Manuals Rev. 1.00, the LSI internal delay for I2C instances 1 to 3 is 5 ns (typ.), which differs from the default 50 ns as specified for instance 0. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Link: https://lore.kernel.org/r/1eac63f15a776e492ff8a2d8447c5e1019982dd1.1620138979.git.geert+renesas@glider.be Link: https://lore.kernel.org/r/73c96fd455df82ef04fd1db6d7dd79b4679f6c56.1620138979.git.geert+renesas@glider.be
2021-05-25ARM: dts: koelsch: Rename sw2 to keyboardGeert Uytterhoeven1-2/+2
Rename "sw2_pins" and "sw2" to "keyboard_pins" resp. "keyboard", to comply with generic name recommendations. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Link: https://lore.kernel.org/r/3d718cf69e21b1ceea0c29c0e841b9bdda44533d.1619785905.git.geert+renesas@glider.be
2021-05-25ARM: dts: r8a7779, marzen: Fix DU clock namesGeert Uytterhoeven2-1/+2
"make dtbs_check" complains: arch/arm/boot/dts/r8a7779-marzen.dt.yaml: display@fff80000: clock-names:0: 'du.0' was expected Change the first clock name to match the DT bindings. This has no effect on actual operation, as the Display Unit driver in Linux does not use the first clock name on R-Car H1, but just grabs the first clock. Fixes: 665d79aa47cb3983 ("ARM: shmobile: marzen: Add DU external pixel clock to DT") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Link: https://lore.kernel.org/r/9d5e1b371121883b3b3e10a3df43802a29c6a9da.1619699965.git.geert+renesas@glider.be
2021-05-25ARM: dts: renesas: Add fck to etheravb-rcar-gen2 clock-names listAdam Ford9-0/+9
The bindings have been updated to support two clocks. Add a clock-names list in the device tree with fck in it. Signed-off-by: Adam Ford <aford173@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20210224115146.9131-2-aford173@gmail.com Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2021-05-25ARM: dts: aspeed: ast2600evb: Add dts file for A1 and A0Steven Lee2-0/+16
aspeed-ast2600-evb.dts was modified for supporting A2 evb. Since A1/A0 evbs don't have GPIO regulators and SD clock frequency (SCU210) is different to A2 as well. Adding a new dts that removes new nodes created in aspeed-ast2600-evb.dts is necessary. Signed-off-by: Steven Lee <steven_lee@aspeedtech.com> Acked-by: Andrew Jeffery <andrew@aj.id.au> Link: https://lore.kernel.org/r/20210524073308.9328-4-steven_lee@aspeedtech.com Signed-off-by: Joel Stanley <joel@jms.id.au>
2021-05-25ARM: dts: aspeed: ast2600evb: Add phase correction for emmc controller.Steven Lee1-1/+2
Set MMC timing-phase register by adding the phase correction binding in the device tree. Signed-off-by: Steven Lee <steven_lee@aspeedtech.com> Acked-by: Andrew Jeffery <andrew@aj.id.au> Reviewed-by: Joel Stanley <joel@jms.id.au> Link: https://lore.kernel.org/r/20210524073308.9328-3-steven_lee@aspeedtech.com Signed-off-by: Joel Stanley <joel@jms.id.au>
2021-05-25ARM: dts: aspeed: ast2600evb: Add sdhci node and gpio regulator for A2 evb.Steven Lee1-0/+84
AST2600 A2 (or newer) EVB has gpio regulators for toggling signal voltage between 3.3v and 1.8v, the patch adds sdhci node and gpio regulator in the dts file and adds comment for describing the reference design. Signed-off-by: Steven Lee <steven_lee@aspeedtech.com> Acked-by: Andrew Jeffery <andrew@aj.id.au> Link: https://lore.kernel.org/r/20210524073308.9328-2-steven_lee@aspeedtech.com Signed-off-by: Joel Stanley <joel@jms.id.au>
2021-05-24ARM: dts: sun8i: h3: orangepi-plus: Fix ethernet phy-modeSalvatore Bonaccorso1-1/+1
Commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx delay config") sets the RX/TX delay according to the phy-mode property in the device tree. For the Orange Pi Plus board this is "rgmii", which is the wrong setting. Following the example of a900cac3750b ("ARM: dts: sun7i: a20: bananapro: Fix ethernet phy-mode") the phy-mode is changed to "rgmii-id" which gets the Ethernet working again on this board. Fixes: bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx delay config") Reported-by: "B.R. Oake" <broake@mailfence.com> Reported-by: Vagrant Cascadian <vagrant@reproducible-builds.org> Link: https://bugs.debian.org/988574 Signed-off-by: Salvatore Bonaccorso <carnil@debian.org> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20210524122111.416885-1-carnil@debian.org
2021-05-24ARM: dts: ux500: Fix orientation of Janice accelerometerLinus Walleij1-4/+3
This fixes up the axis on the Janice accelerometer to give the right orientation according to tests. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2021-05-23ARM: dts: imx: emcon-avari: Fix nxp,pca8574 #gpio-cellsGeert Uytterhoeven1-1/+1
According to the DT bindings, #gpio-cells must be two. Fixes: 63e71fedc07c4ece ("ARM: dts: Add support for emtrion emCON-MX6 series") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2021-05-23ARM: dts: imx7d-pico: Fix the 'tuning-step' propertyFabio Estevam1-1/+1
According to Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.yaml, the correct name of the property is 'fsl,tuning-step'. Fix it accordingly. Signed-off-by: Fabio Estevam <festevam@gmail.com> Fixes: f13f571ac8a1 ("ARM: dts: imx7d-pico: Extend peripherals support") Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2021-05-23ARM: dts: imx7d-meerkat96: Fix the 'tuning-step' propertyFabio Estevam1-1/+1
According to Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.yaml, the correct name of the property is 'fsl,tuning-step'. Fix it accordingly. Signed-off-by: Fabio Estevam <festevam@gmail.com> Fixes: ae7b3384b61b ("ARM: dts: Add support for 96Boards Meerkat96 board") Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2021-05-23ARM: dts: imx53-ard: Correct Ethernet node nameGeert Uytterhoeven1-1/+1
make dtbs_check: lan9220@f4000000: $nodename:0: 'lan9220@f4000000' does not match '^ethernet(@.*)?$' Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2021-05-23ARM: dts: i.MX51: digi-connectcore-som: Correct Ethernet node nameGeert Uytterhoeven1-1/+1
make dtbs_check: lan9221@5,0: $nodename:0: 'lan9221@5,0' does not match '^ethernet(@.*)?$' Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2021-05-23ARM: dts: imx6dl-riotboard: configure PHY clock and set proper EEE valueOleksij Rempel1-0/+2
Without SoC specific PHY fixups the network interface on this board will fail to work. Provide missing DT properties to make it work again. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2021-05-23ARM: dts: imx6: edmqmx6: set phy-mode to RGMII-IDOleksij Rempel1-1/+1
Latest kernel is actually using phy-mode property, so set proper value to make fec interface work again. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2021-05-23ARM: dts: imx6qdl-sabresd: Configure the gpio for hp detectShengjiu Wang1-0/+9
Configure the gpio for hp detect for wm8962 sound card Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2021-05-23ARM: dts: imx6qdl-sabresd: Add asrc support for wm8962 sound cardShengjiu Wang1-0/+1
Add asrc support for wm8962 sound card. Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2021-05-23ARM: dts: imx: Add i.mx6q DaSheng COM-9XX SBC board supportDillon Min3-0/+476
The DaSheng Com-9xx is and ARM based signle board computer (SBC) featuring: - i.MX6Q - 2GiB LPDDR3 DRAM - 8GiB eMMC 5.0 FLASH - 4MiB SPI Flash - USB 2.0 Host/Device - Multiple multi-protocol RS232/RS485 Serial ports - microSD socket - 5V DC power input - HDMI1.4a,1080p@60 - RGMIIx1 Gigabit Ethernet - CSI0x1, connect with ov2659 Signed-off-by: Dillon Min <dillon.minfei@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2021-05-23ARM: dts: imx6dl-yapp4: Use aliases to set custom MMC device indexesMichal Vokáč1-0/+2
Until commit fa2d0aa96941 ("mmc: core: Allow setting slot index via device tree alias") was introduced, our usdhc3 and usdhc4 devices were enumerated as mmc0 and mmc1. The mmc1 device is used to boot/update the board and its name must be fixed. With the referenced commit, aliases from imx6qdl.dtsi took effect. Override the aliases to get back the original device indexes. Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2021-05-22ARM: dts: imx7d-sdb: Add HDMI audio sound cardShengjiu Wang1-0/+7
Add HDMI audio sound card, the interface is sii902x. Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2021-05-22ARM: dts: imx6ul-14x14-evk: Switch to fsl-asoc-card sound cardShengjiu Wang1-29/+21
There is issue with simple sound card, the simple sound card can't configure the pll of codec. [ 115.352669] wm8960 1-001a: failed to configure clock [ 115.358843] wm8960 1-001a: ASoC: error at snd_soc_dai_hw_params on wm8960-hifi: -22 So Switch to fsl-asoc-card and the fsl-asoc-card can support asrc module as front-end component. Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2021-05-22ARM: dts: imx28: Add DTS description of imx28 based XEA boardLukasz Majewski3-1/+271
This patch adds DTS definition of the imx278 based XEA board. Signed-off-by: Lukasz Majewski <lukma@denx.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2021-05-22ARM: dts: gemini: remove xxx-cells from displayCorentin Labbe1-2/+0
dtb_check complains about #address-cells and #size-cells, so lets remove them. Signed-off-by: Corentin Labbe <clabbe@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2021-05-22ARM: dts: gemini-dlink-dir-685: Remove address from display portCorentin Labbe1-2/+1
The address and reg adds no value to the port node, remove them. Signed-off-by: Corentin Labbe <clabbe@baylibre.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Copyright © 1996 – 2026 Jason A. Donenfeld. All Rights Reverse Engineered.