aboutsummaryrefslogtreecommitdiffstats
path: root/arch/arm/boot
AgeCommit message (Collapse)AuthorFilesLines
2020-07-20ARM: dts: sunxi: libretech-all-h3-cc: Add regulator supply to all CPU coresChen-Yu Tsai1-0/+12
The device tree currently only assigns the a supply for the first CPU core, when in reality the regulator supply is shared by all four cores. This might cause an issue if the implementation does not realize the sharing of the supply. Assign the same regulator supply to the remaining CPU cores to address this. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Link: https://lore.kernel.org/r/20200717160053.31191-2-wens@kernel.org
2020-07-20ARM: dts: at91: sama5d3_xplained: change phy-modeAlexandre Belloni1-1/+1
Since commit bcf3440c6dd7 ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY"), networking is broken on sama5d3 xplained. The device tree has phy-mode = "rgmii" and this worked before, because KSZ9031 PHY started with default RGMII internal delays configuration (TX off, RX on 1.2 ns) and MAC provided TX delay. After above commit, the KSZ9031 PHY starts handling phy mode properly and disables RX delay, as result networking is become broken. Fix it by switching to phy-mode = "rgmii-rxid" to reflect previous behavior. Fixes: bcf3440c6dd78bfe ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY") Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20200717233644.841080-1-alexandre.belloni@bootlin.com
2020-07-20ARM: dts: ux500-skomer: Correct accel mounting matrixLinus Walleij1-2/+2
This corrects the mounting matrix for the BMA254 accelerometer to what makes PostmarketOS actually orient the screen the right way on this device. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20200719201603.3610389-1-linus.walleij@linaro.org
2020-07-20ARM: dts: exynos: Disable frequency scaling for FSYS bus on Odroid XU3 familyMarek Szyprowski1-6/+0
Commit 1019fe2c7280 ("ARM: dts: exynos: Adjust bus related OPPs to the values correct for Exynos5422 Odroids") changed the parameters of the OPPs for the FSYS bus. Besides the frequency adjustments, it also removed the 'shared-opp' property from the OPP table used for FSYS_APB and FSYS busses. This revealed that in fact the FSYS bus frequency scaling never worked. When one OPP table is marked as 'opp-shared', only the first bus which selects the OPP sets the rate of its clock. Then OPP core assumes that the other busses have been changed to that OPP and no change to their clock rates are needed. Thus when FSYS_APB bus, which was registered first, set the rate for its clock, the OPP core did not change the FSYS bus clock later. The mentioned commit removed that behavior, what introduced a regression on some Odroid XU3 boards. Frequency scaling of the FSYS bus causes instability of the USB host operation, what can be observed as network hangs. To restore old behavior, simply disable frequency scaling for the FSYS bus. Reported-by: Willy Wolff <willy.mh.wolff.ml@gmail.com> Fixes: 1019fe2c7280 ("ARM: dts: exynos: Adjust bus related OPPs to the values correct for Exynos5422 Odroids") Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
2020-07-20ARM: dts: aspeed: tacoma: Fix gpio-key definitionsJoel Stanley1-59/+0
This patch was applied twice. Signed-off-by: Joel Stanley <joel@jms.id.au>
2020-07-20ARM: dts: rainier: Configure ball Y23 as GPIOP7 for MCLR_VPPAndrew Jeffery1-0/+7
GPIOP7 is used in the Rainier design to manage the state of a microcontroller elsewhere in the system but its ball, Y23, is the driver of the heartbeat LED on the ast2600-evb and the SoC defaults Y23 at power-on to the pulse-train behaviour used to drive the LED. This causes much confusion for the micro in the Rainier system, so hog the line as early as possible. Signed-off-by: Andrew Jeffery <andrew@aj.id.au> Signed-off-by: Joel Stanley <joel@jms.id.au>
2020-07-20ARM: dts: aspeed: rainier: Add second cfam on the hubEddie James1-0/+36
The hub FSI master can access the cfams on two other processors. Reflect this by adding a second cfam to the first hub description. Signed-off-by: Eddie James <eajames@linux.ibm.com> Tested-by: Andrew Geissler <geissonator@yahoo.com> Signed-off-by: Joel Stanley <joel@jms.id.au>
2020-07-20ARM: dts: aspeed: rainier: Add line-name checkstopBen Tyner1-1/+1
Rainier uses GPIO B6 as the checkstop GPIO. Define the line-name so that this GPIO can be found by name. Signed-off-by: Ben Tyner <ben.tyner@ibm.com> Signed-off-by: Joel Stanley <joel@jms.id.au>
2020-07-20ARM: dts: aspeed: tacoma: Remove checkstop gpio-keyBen Tyner1-6/+0
The attention handler will monitor the checkstop gpio via the character device interface so it needs to not be defined. Signed-off-by: Ben Tyner <ben.tyner@ibm.com> Signed-off-by: Joel Stanley <joel@jms.id.au>
2020-07-20ARM: dts: aspeed: tacoma: Enable XDMA engineEddie James1-0/+11
Add a reserved memory node for the VGA memory. Add the XDMA engine node, enable it, and point it's memory region to the VGA memory. Signed-off-by: Eddie James <eajames@linux.ibm.com> Signed-off-by: Joel Stanley <joel@jms.id.au>
2020-07-20ARM: dts: aspeed: witherspoon: Enable XDMA engineEddie James1-0/+11
Add a reserved memory node for the VGA memory. Add the XDMA engine node, enable it, and point it's memory region to the VGA memory. Signed-off-by: Eddie James <eajames@linux.ibm.com> Signed-off-by: Joel Stanley <joel@jms.id.au>
2020-07-20ARM: dts: aspeed: ast2600: Update XDMA engine nodeEddie James1-12/+3
Add the PCI-E root complex reset, correct the pcie-device property, and add the Aspeed SCU interrupt controller include. Signed-off-by: Eddie James <eajames@linux.ibm.com> Signed-off-by: Joel Stanley <joel@jms.id.au>
2020-07-20ARM: dts: aspeed: ast2500: Update XDMA engine nodeEddie James1-2/+3
Correct the pcie-device property, and add the Aspeed SCU interrupt controller include. Signed-off-by: Eddie James <eajames@linux.ibm.com> Signed-off-by: Joel Stanley <joel@jms.id.au>
2020-07-20ARM: dts: imx6qdl-icore: Fix OTG_ID pin and sdcard detectMichael Trimarchi1-1/+2
The current pin muxing scheme muxes GPIO_1 pad for USB_OTG_ID because of which when card is inserted, usb otg is enumerated and the card is never detected. [ 64.492645] cfg80211: failed to load regulatory.db [ 64.492657] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware [ 76.343711] ci_hdrc ci_hdrc.0: EHCI Host Controller [ 76.349742] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 2 [ 76.388862] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00 [ 76.396650] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.08 [ 76.405412] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 76.412763] usb usb2: Product: EHCI Host Controller [ 76.417666] usb usb2: Manufacturer: Linux 5.8.0-rc1-next-20200618 ehci_hcd [ 76.424623] usb usb2: SerialNumber: ci_hdrc.0 [ 76.431755] hub 2-0:1.0: USB hub found [ 76.435862] hub 2-0:1.0: 1 port detected The TRM mentions GPIO_1 pad should be muxed/assigned for card detect and ENET_RX_ER pad for USB_OTG_ID for proper operation. This patch fixes pin muxing as per TRM and is tested on a i.Core 1.5 MX6 DL SOM. [ 22.449165] mmc0: host does not support reading read-only switch, assuming write-enable [ 22.459992] mmc0: new high speed SDHC card at address 0001 [ 22.469725] mmcblk0: mmc0:0001 EB1QT 29.8 GiB [ 22.478856] mmcblk0: p1 p2 Fixes: 6df11287f7c9 ("ARM: dts: imx6q: Add Engicam i.CoreM6 Quad/Dual initial support") Cc: stable@vger.kernel.org Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2020-07-20ARM: dts: vf610-zii-ssmb-spu3: Add node for switch watchdogChris Healy1-0/+12
Add I2C child node for switch watchdog present on SPU3 Signed-off-by: Chris Healy <cphealy@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2020-07-20ARM: dts: vf610-zii-ssmb-dtu: Add no-sdio/no-sd propertiesChris Healy1-0/+3
esdhc0 is connected to an eMMC, so it is safe to pass the "no-sdio"/"no-sd" properties. esdhc1 is wired to a standard SD socket, so pass the "no-sdio" property. Signed-off-by: Chris Healy <cphealy@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2020-07-20ARM: dts: imx6sx-sabreauto: Fix the phy-mode on fec2Fabio Estevam1-1/+1
Commit 0672d22a1924 ("ARM: dts: imx: Fix the AR803X phy-mode") fixed the phy-mode for fec1, but missed to fix it for the fec2 node. Fix fec2 to also use "rgmii-id" as the phy-mode. Cc: <stable@vger.kernel.org> Fixes: 0672d22a1924 ("ARM: dts: imx: Fix the AR803X phy-mode") Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2020-07-20ARM: dts: imx6sx-sdb: Fix the phy-mode on fec2Fabio Estevam1-1/+1
Commit 0672d22a1924 ("ARM: dts: imx: Fix the AR803X phy-mode") fixed the phy-mode for fec1, but missed to fix it for the fec2 node. Fix fec2 to also use "rgmii-id" as the phy-mode. Cc: <stable@vger.kernel.org> Fixes: 0672d22a1924 ("ARM: dts: imx: Fix the AR803X phy-mode") Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2020-07-20ARM: dts: imx6q-tbs2910: Pass reset-assert-usFabio Estevam1-1/+2
According to the AR8035 datasheet: "When using crystal, the clock is generated internally after power is stable. For a reliable power on reset, suggest to keep asserting the reset low long enough (10ms) to ensure the clock is stable and clock-to-reset 1ms requirement is satisfied." Pass the 'reset-assert-us' property to describe such requirement. While at it, use the 'reset-gpios' property inside the the mdio node instead of the deprecated usage of 'phy-reset-gpios'. Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Soeren Moch <smoch@web.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2020-07-20ARM: dts: imx6q-tbs2910: Add an mdio nodeFabio Estevam1-0/+11
imx6q-tbs2910 has an Atheros AR8035 Ethernet PHY at address 4. The AR8035 provides a 125MHz clock to the ENET_REF_CLK i.MX6 pin. Improve the Ethernet representation by adding an mdio node with such information. This fixes an Ethernet regression in U-Boot as U-Boot AR803X driver now expects the 'qca,clk-out-frequency' property to be passed via device tree. Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Soeren Moch <smoch@web.de> Tested-by: Soeren Moch <smoch@web.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2020-07-20ARM: dts: imx6qdl-sabresd: Pass reset-assert-usFabio Estevam1-1/+2
According to the AR8031 datasheet: "When using crystal, clock is generated internally after the power is stable. In order to get reliable power-on-reset, it is recommended to keep asserting the reset low signal long enough (10 ms) to ensure the clock is stable and clock-to-reset (1 ms) requirement is satisfied." Pass the 'reset-assert-us' property to describe such requirement. While at it, use the 'reset-gpios' property inside the the mdio node instead of the deprecated usage of 'phy-reset-gpios'. Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Soeren Moch <smoch@web.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2020-07-20ARM: dts: imx6qdl-sabresd: Add an mdio nodeFabio Estevam1-0/+11
imx6qdl-sabresd has an Atheros AR8031 Ethernet PHY at address 1. The AR8031 provides a 125MHz clock to the ENET_REF_CLK i.MX6 pin. Improve the Ethernet representation by adding an mdio node with such information. An advantage of adding the mdio node is that the AR8031 initialization code in the mx6sabresd board file in U-Boot can totally be removed. Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Soeren Moch <smoch@web.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2020-07-20ARM: dts: imx6qdl-gw: add Gateworks System Controller supportTim Harvey14-57/+2076
Add Gateworks System Controller support to Gateworks Ventana boards: - add dt bindings for GSC mfd driver and hwmon driver for ADC's and fan controllers. - add dt bindings for gpio-keys driver for push-button and interrupt events Signed-off-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2020-07-18ARM: dts: socfpga: add the temperature sensor to the Arria10 devkitDinh Nguyen1-0/+5
Add the Maxim max1619 temp sensor that is on the Arria10 devkit. Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
2020-07-18arm: dts: socfpga: add reset-names to spi nodeDinh Nguyen2-0/+4
Add reset-names = "spi" to spi dts nodes. Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
2020-07-18ARM: dts: dlink-dns327l: fix reg-init PHYDaniel González Cabanelas1-3/+2
The marvell PHY reg-init registers for the D-Link DNS-327L are wrong. Currently the first field is used to set the page 2, but this is pointless. The usage is not correct, and we are setting the wrong registers. Fix it. Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
2020-07-18ARM: dts: kirkwood: Replace HTTP links with HTTPS onesAlexander A. Klimov1-1/+1
Rationale: Reduces attack surface on kernel devs opening the links for MITM as HTTPS traffic is much harder to manipulate. Deterministic algorithm: For each file: If not .svg: For each line: If doesn't contain `\bxmlns\b`: For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`: If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`: If both the HTTP and HTTPS versions return 200 OK and serve the same content: Replace HTTP with HTTPS. Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
2020-07-18ARM: dts: rockchip: Fix VBUS on rk3288-vyasaMichael Trimarchi1-2/+1
Connect the voltage regulator of vbus to the otg connector. Depending on the current mode this is enabled (in "host" mode") or disabled (in "peripheral" mode). The regulator must be updated if the controller is configured in "otg" mode and the status changes between "host" and "peripheral". Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Link: https://lore.kernel.org/r/20200707101214.2301768-1-michael@amarulasolutions.com Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2020-07-18ARM: dts: rockchip: Add Radxa Rock Pi N8 initial supportJagan Teki2-0/+18
Rock Pi N8 is a Rockchip RK3288 based SBC, which has - VMARC RK3288 SOM (as per SMARC standard) from Vamrs. - Compatible carrier board from Radxa. VAMRC RK3288 SOM need to mount on top of radxa dalang carrier board for making Rock Pi N8 SBC. So, add initial support for Rock Pi N8 by including rk3288, rk3288 vamrc-som and raxda dalang carrier board dtsi files. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Link: https://lore.kernel.org/r/20200715083418.112003-8-jagan@amarulasolutions.com Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2020-07-18ARM: dts: rockchip: Add VMARC RK3288 SOM initial supportJagan Teki1-0/+270
VMARC RK3288 SOM is a standard SMARC SOM design with Rockchip RK3288 SoC, which is designed by Vamrs. Specification: - Rockchip RK3288 - PMIC: RK808 - eMMC: 16GB/32GB/64GB - SD slot - 2xUSB-2.0, 1xUSB3.0 - USB-C for power supply - Ethernet - HDMI, MIPI-DSI/CSI, eDP Add initial support for VMARC RK3288 SOM, this would use with associated carrier board. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Link: https://lore.kernel.org/r/20200715083418.112003-7-jagan@amarulasolutions.com Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2020-07-18arm64: dts: rk3399pro: vmarc-som: Move common properties into CarrierJagan Teki1-4/+14
Some of gmac, sdmmc node properties are common across rk3288 and rk3399pro SOM's so move them into Carrier dtsi. Chosen node is specific to rk3399pro configure SBC, so move it into RockPI N10 dts. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Link: https://lore.kernel.org/r/20200715083418.112003-5-jagan@amarulasolutions.com Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2020-07-18arm64: dts: rk3399pro: vmarc-som: Move supply regulators into CarrierJagan Teki1-0/+19
Supply regulators are common across different variants of vmarc SOM's since the Type C power controller IC is part of the carrier board. So, move the supply regulators into carrier board dtsi. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Link: https://lore.kernel.org/r/20200715083418.112003-4-jagan@amarulasolutions.com Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2020-07-18ARM: dts: rockchip: dalang-carrier: Move i2c nodes into SOMJagan Teki1-32/+0
I2C nodes and associated slave devices defined in Carrier board are specific to rk3399pro vmrac SOM. So, move them into SOM dtsi. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Link: https://lore.kernel.org/r/20200715083418.112003-2-jagan@amarulasolutions.com Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2020-07-18ARM: dts: rockchip: Add 'arm,pl330-periph-burst' for dmacSugar Zhang5-0/+9
This patch Add the quirk to specify to use burst transfer for better compatible and higher performance. Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com> Link: https://lore.kernel.org/r/1593439866-68459-1-git-send-email-sugar.zhang@rock-chips.com Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2020-07-17Merge tag 'arm-fixes-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc into masterLinus Torvalds5-8/+14
Pull ARM SoC fixes from Arnd Bergmann: "This time there are a number of actual code fixes, plus a small set of device tree issues getting addressed: Renesas: - one defconfig cleanup to allow a later Kconfig change Intel socfpga: - enable QSPI devices on some machines - fix DTC validation warnings TI OMAP: - Two DEBUG_ATOMIC_SLEEP fixes for ti-sysc interconnect target module driver - A regression fix for ti-sysc no-idle handling that caused issues compared to earlier platform data based booting - A fix for memory leak for omap_hwmod_allocate_module - Fix d_can driver probe for am437x NXP i.MX: - A couple of fixes on i.MX platform device registration code to stop the use of invalid IRQ 0. - Fix a regression seen on ls1021a platform, caused by commit 52102a3ba6a61 ("soc: imx: move cpu code to drivers/soc/imx"). - Fix a misconfiguration of audio SSI on imx6qdl-gw551x board. Amlogic Meson: - misc DT fixes - SoC ID fixes to detect all chips correctly" * tag 'arm-fixes-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: arm64: dts: spcfpga: Align GIC, NAND and UART nodenames with dtschema ARM: dts: socfpga: Align L2 cache-controller nodename with dtschema arm64: dts: stratix10: increase QSPI reg address in nand dts file arm64: dts: stratix10: add status to qspi dts node arm64: dts: agilex: add status to qspi dts node ARM: dts: Fix dcan driver probe failed on am437x platform ARM: OMAP2+: Fix possible memory leak in omap_hwmod_allocate_module arm64: defconfig: Enable CONFIG_PCIE_RCAR_HOST soc: imx: check ls1021a ARM: imx: Remove imx_add_imx_dma() unused irq_err argument ARM: imx: Provide correct number of resources when registering gpio devices ARM: dts: imx6qdl-gw551x: fix audio SSI bus: ti-sysc: Do not disable on suspend for no-idle bus: ti-sysc: Fix sleeping function called from invalid context for RTC quirk bus: ti-sysc: Fix wakeirq sleeping function called from invalid context ARM: dts: meson: Align L2 cache-controller nodename with dtschema arm64: dts: meson-gxl-s805x: reduce initial Mali450 core frequency arm64: dts: meson: add missing gxl rng clock soc: amlogic: meson-gx-socinfo: Fix S905X3 and S905D3 ID's
2020-07-17Merge tag 'tegra-for-5.9-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dtArnd Bergmann53-2195/+7251
ARM: tegra: Device tree changes for v5.9-rc1 This adds device trees for the ASUS Google Nexus 7 and Acer Iconia Tab A500. In addition there are a slew of fixes to existing device trees in preparation for validating the DTBs against json-schema. * tag 'tegra-for-5.9-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (38 commits) ARM: tegra: Add device-tree for ASUS Google Nexus 7 ARM: tegra: Add device-tree for Acer Iconia Tab A500 ARM: tegra: Add HDMI supplies on Nyan boards ARM: tegra: Add missing DSI controller on Tegra30 ARM: tegra: Add i2c-bus subnode for DPAUX controllers ARM: tegra: The Tegra30 SDHCI is not backwards-compatible ARM: tegra: The Tegra30 DC is not backwards-compatible ARM: tegra: Remove spurious comma from node name ARM: tegra: Add parent clock to DSI output ARM: tegra: Use standard names for SRAM nodes ARM: tegra: seaboard: Use standard battery bindings ARM: tegra: Use standard names for LED nodes ARM: tegra: Use numeric unit-addresses ARM: tegra: medcom-wide: Remove extra panel power supply ARM: tegra: Use proper unit-addresses for OPPs ARM: tegra: Add missing clock-names for SDHCI controllers ARM: tegra: Fix order of XUSB controller clocks ARM: tegra: Add #reset-cells to Tegra124 memory controller ARM: tegra: Add missing panel power supplies ARM: tegra: Add micro-USB A/B port on Jetson TK1 ... Link: https://lore.kernel.org/r/20200717161300.1661002-5-thierry.reding@gmail.com Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2020-07-17Merge tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/dtArnd Bergmann6-0/+160
ARM: dts: amlogic updates for v5.9 - power-domain and MMC updates * tag 'amlogic-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic: ARM: dts: meson8b: odroidc1: enable the SDHC controller ARM: dts: meson8b: ec100: enable the SDHC controller ARM: dts: meson: add the SDHC MMC controller ARM: dts: meson8b: add power domain controller ARM: dts: meson8m2: add resets for the power domain controller ARM: dts: meson8: add power domain controller Link: https://lore.kernel.org/r/7hd04uf2o8.fsf@baylibre.com Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2020-07-17Merge tag 'socfpga_fixes_for_v5.8_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into arm/fixesArnd Bergmann2-2/+2
arm/arm64: dts: socfpga: fixes for v5.8 - Add status = "okay" in QSPI - Increase QSPI size in reg property - Fix dtschema for SoCFPGA platforms * tag 'socfpga_fixes_for_v5.8_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux: arm64: dts: spcfpga: Align GIC, NAND and UART nodenames with dtschema ARM: dts: socfpga: Align L2 cache-controller nodename with dtschema arm64: dts: stratix10: increase QSPI reg address in nand dts file arm64: dts: stratix10: add status to qspi dts node arm64: dts: agilex: add status to qspi dts node Link: https://lore.kernel.org/r/20200717155758.18233-1-dinguyen@kernel.org Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2020-07-17Merge tag 'renesas-arm-dt-for-v5.9-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dtArnd Bergmann23-58/+53
Renesas ARM DT updates for v5.9 (take two) - SPI Multi I/O Bus Controller (RPC-IF) support for R-Car V3H and V3M, including QSPI support for the Condor, Eagle, V3HSK, and V3MSK boards, - Initial support for the RZ/G2H SoC on the HopeRun HiHope RZ/G2H board, - Initial support for the Beacon EmbeddedWorks RZ/G2M board, - Minor fixes and improvements. * tag 'renesas-arm-dt-for-v5.9-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: (34 commits) ARM: dts: sh73a0: Add missing clocks to sound node arm64: dts: renesas: r8a774e1: Add CAN[FD] support arm64: dts: renesas: r8a774e1: Add RWDT node arm64: dts: renesas: r8a774e1: Add MSIOF nodes arm64: dts: renesas: r8a774e1: Add I2C and IIC-DVFS support arm64: dts: renesas: r8a774e1: Add SDHI nodes arm64: dts: renesas: r8a774e1: Add SCIF and HSCIF nodes arm64: dts: renesas: r8a774e1: Add TMU device nodes arm64: dts: renesas: r8a774e1: Add CMT device nodes arm64: dts: renesas: r8a774e1: Add RZ/G2H thermal support arm64: dts: renesas: r8a774e1: Add operating points arm64: dts: renesas: Introduce r8a774a1-beacon-rzg2m-kit arm64: dts: renesas: r8a774e1: Add Ethernet AVB node arm64: dts: renesas: r8a774e1: Add GPIO device nodes arm64: dts: renesas: r8a774e1: Add SYS-DMAC device nodes arm64: dts: renesas: r8a774e1: Add IPMMU device nodes ARM: dts: gose: Fix ports node name for adv7612 ARM: dts: renesas: Fix SD Card/eMMC interface device node names arm64: dts: renesas: Fix SD Card/eMMC interface device node names arm64: dts: renesas: add full-pwr-cycle-in-suspend into eMMC nodes ... Link: https://lore.kernel.org/r/20200717112427.26032-2-geert+renesas@glider.be Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2020-07-17ARM: dts: sh73a0: Add missing clocks to sound nodeGeert Uytterhoeven1-0/+1
The device node for the FIFO-buffered Serial Interface sound node lacks the "clocks" property, as the DTS file didn't describe any clocks yet at its introduction. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20200519075525.24742-1-geert+renesas@glider.be
2020-07-17ARM: dts: gose: Fix ports node name for adv7612Niklas Söderlund1-1/+1
When adding the adv7612 device node the ports node was misspelled as port, fix this. Fixes: bc63cd87f3ce924f ("ARM: dts: gose: add HDMI input") Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Link: https://lore.kernel.org/r/20200713111016.523189-1-niklas.soderlund+renesas@ragnatech.se Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2020-07-17ARM: dts: renesas: Fix SD Card/eMMC interface device node namesYoshihiro Shimoda17-50/+50
Fix the device node names as "mmc@". Fixes: 66474697923c ("ARM: dts: r7s72100: add sdhi to device tree") Fixes: a49f76cddaee ("ARM: dts: r7s9210: Add SDHI support") Fixes: 43304a5f5106 ("ARM: shmobile: r8a73a4: tidyup DT node naming") Fixes: 7d907894bfe3 ("ARM: shmobile: r8a7740: tidyup DT node naming") Fixes: 3ab2ea5fd1ce ("ARM: dts: r8a7742: Add SDHI nodes") Fixes: 63ce8a617b51 ("ARM: dts: r8a7743: Add SDHI controllers") Fixes: b591e323b271 ("ARM: dts: r8a7744: Add SDHI nodes") Fixes: d83010f87ab3 ("ARM: dts: r8a7744: Initial SoC device tree") Fixes: 7079131ef9b9 ("ARM: dts: r8a7745: Add SDHI controllers") Fixes: 0485da788028 ("ARM: dts: r8a77470: Add SDHI1 support") Fixes: 15aa5a95e820 ("ARM: dts: r8a77470: Add SDHI0 support") Fixes: f068cc816015 ("ARM: dts: r8a77470: Add SDHI2 support") Fixes: 14e1d9147d96 ("ARM: shmobile: r8a7778: tidyup DT node naming") Fixes: 2624705ceb7b ("ARM: shmobile: r8a7779: tidyup DT node naming") Fixes: b718aa448378 ("ARM: shmobile: r8a7790: tidyup DT node naming") Fixes: b7ed8a0dd4f1 ("ARM: shmobile: Add SDHI devices to r8a7791 DTSI") Fixes: ce01b14ecf19 ("ARM: dts: r8a7792: add SDHI support") Fixes: fc9ee228f500 ("ARM: dts: r8a7793: Add SDHI controllers") Fixes: b8e8ea127d00 ("ARM: shmobile: r8a7794: add SDHI DT support") Fixes: 33f6be3bf6b7 ("ARM: shmobile: sh73a0: tidyup DT node naming") Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Link: https://lore.kernel.org/r/1594382936-14114-1-git-send-email-yoshihiro.shimoda.uh@renesas.com Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2020-07-17ARM: dts: hisilicon: Align L2 cache-controller nodename with dtschemaKrzysztof Kozlowski2-2/+2
Fix dtschema validator warnings like: l2-cache: $nodename:0: 'l2-cache' does not match '^(cache-controller|cpu)(@[0-9a-f,]+)*$' Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
2020-07-16Merge tag 'omap-for-v5.9/dt-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dtArnd Bergmann113-162/+423
More dts changes for omaps for v5.9 A series of changes to configure IPU and DSP remoteproc for omap4 & 5. And a change to configure the default mux for am335x-pocketbeagle, and a change to use https for external links. * tag 'omap-for-v5.9/dt-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: Replace HTTP links with HTTPS ones: OMAP DEVICE TREE SUPPORT ARM: dts: omap5-uevm: Add watchdog timers for IPU and DSP ARM: dts: omap4-panda-common: Add watchdog timers for IPU and DSP ARM: dts: omap5-uevm: Add system timers to DSP and IPU ARM: dts: omap5-uevm: Add CMA pools and enable IPU & DSP ARM: dts: omap5: Add aliases for rproc nodes ARM: dts: omap5: Add DSP and IPU nodes ARM: dts: omap4-panda-common:: Add system timers to DSP and IPU ARM: dts: omap4-panda-common: Add CMA pools and enable IPU & DSP ARM: dts: omap4: Add aliases for rproc nodes ARM: dts: omap4: Add IPU DT node ARM: dts: omap4: Update the DSP node ARM: dts: omap5: Add timer_sys_ck clocks for timers ARM: dts: omap4: Add timer_sys_ck clocks for timers ARM: dts: am335x-pocketbeagle: set default mux for gpio pins Link: https://lore.kernel.org/r/pull-1594838111-649880@atomide.com-3 Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2020-07-16Merge tag 'omap-for-v5.9/ti-sysc-drop-pdata-take2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dtArnd Bergmann9-39/+103
Drop more legacy platform data for omaps for v5.9 A series of changes to drop remaining USB platform data for omap4/5, and am4, and dra7. And a patch to drop AES platform data for omap3. * tag 'omap-for-v5.9/ti-sysc-drop-pdata-take2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: ARM: OMAP2+: Drop legacy platform data for omap5 usb host ARM: OMAP2+: Drop legacy platform data for omap4 usb ARM: OMAP2+: Drop legacy platform data for dra7 dwc3 ARM: OMAP2+: Drop legacy platform data for omap5 dwc3 ARM: OMAP2+: Drop legacy platform data for am4 dwc3 bus: ti-sysc: Add missing quirk flags for usb_host_hs ARM: dts: omap3: Migrate AES from hwmods to sysc-omap2 Link: https://lore.kernel.org/r/pull-1594838111-649880@atomide.com-2 Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2020-07-16Merge tag 'omap-for-v5.8/fixes-rc5-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixesArnd Bergmann1-4/+10
Fixes for omaps for v5.8-rc cycle Few fixes for issues noticed during testing: - Two DEBUG_ATOMIC_SLEEP fixes for ti-sysc interconnect target module driver - A regression fix for ti-sysc no-idle handling that caused issues compared to earlier platform data based booting - A fix for memory leak for omap_hwmod_allocate_module - Fix d_can driver probe for am437x * tag 'omap-for-v5.8/fixes-rc5-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: ARM: dts: Fix dcan driver probe failed on am437x platform ARM: OMAP2+: Fix possible memory leak in omap_hwmod_allocate_module bus: ti-sysc: Do not disable on suspend for no-idle bus: ti-sysc: Fix sleeping function called from invalid context for RTC quirk bus: ti-sysc: Fix wakeirq sleeping function called from invalid context Link: https://lore.kernel.org/r/pull-1594840100-132735@atomide.com Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2020-07-16Merge tag 'imx-fixes-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixesArnd Bergmann1-1/+1
i.MX fixes for 5.8, round 2: - A couple of fixes on i.MX platform device registration code to stop the use of invalid IRQ 0. - Fix a regression seen on ls1021a platform, caused by commit 52102a3ba6a61 ("soc: imx: move cpu code to drivers/soc/imx"). - Fix a misconfiguration of audio SSI on imx6qdl-gw551x board. * tag 'imx-fixes-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: soc: imx: check ls1021a ARM: imx: Remove imx_add_imx_dma() unused irq_err argument ARM: imx: Provide correct number of resources when registering gpio devices ARM: dts: imx6qdl-gw551x: fix audio SSI Link: https://lore.kernel.org/r/20200714145649.GP15718@dragon Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2020-07-16Merge tag 'amlogic-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/fixesArnd Bergmann1-1/+1
Amlogic fixes for v5.8-rc - misc DT fixes, and SoC ID fixes * tag 'amlogic-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic: ARM: dts: meson: Align L2 cache-controller nodename with dtschema arm64: dts: meson-gxl-s805x: reduce initial Mali450 core frequency arm64: dts: meson: add missing gxl rng clock soc: amlogic: meson-gx-socinfo: Fix S905X3 and S905D3 ID's Link: https://lore.kernel.org/r/7hk0zc1ujc.fsf@baylibre.com Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2020-07-16ARM: tegra: Add device-tree for ASUS Google Nexus 7Dmitry Osipenko11-0/+3870
There are few hardware variants of NVIDIA Tegra30-based Nexus 7 device: 1. WiFi-only (named Grouper) 2. GSM (named Tilapia) 3. Using Maxim PMIC (E1565 board ID) 4. Using Ti PMIC (PM269 board ID) This patch adds device-trees for known and tested variants. Link: https://wiki.postmarketos.org/wiki/Google_Nexus_7_2012_(asus-grouper) Tested-by: Pedro Ângelo <pangelo@void.io> Tested-by: Matt Merhar <mattmerhar@protonmail.com> Tested-by: Zack Pearsall <zpearsall@yahoo.com> Signed-off-by: David Heidelberg <david@ixit.cz> Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2020-07-16ARM: tegra: Add device-tree for Acer Iconia Tab A500Dmitry Osipenko2-0/+1439
Add device-tree for Acer Iconia Tab A500, which is NVIDIA Tegra20-based tablet device. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
Copyright © 1996 – 2026 Jason A. Donenfeld. All Rights Reverse Engineered.