| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Switch at91sam9n12 boards to the new PMC clock bindings.
Link: https://lore.kernel.org/r/20200116173510.427403-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Switch sama5d3 boards to the new PMC clock bindings.
This prevents the wb50n to use the out of spec rate for USART1.
Link: https://lore.kernel.org/r/20200110222744.1261464-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Add a node for BCM4330/2 SDIO chip on SDHCI bus #3 and the required MMC
power sequence node for the Exynos4210-based UniversalC210 board.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Add a node for BCM43342A SDIO chip on MSHC bus #1 and the required MMC
power sequence node for the Exynos3250-based Rinato board.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
mshc_0 node doesn't have any children, so there is no need for address
and size-cells properties.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Remove the 'interrupts' and 'interrupts-parent' properties, which have
been superseded by the interrupts-extended property. While touching this,
fix the interrupts flags to correctly describe the hardware.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Both CPU-freq and dev-freq drivers support proper regulator lookup from
device-tree, so the early introduced hacks for registering main ARM VDD
regulator under 'vdd_arm' name are no longer needed. Similar for devfreq.
Fix this by removing the obsolete comments and changing the regulator
names to the one, which match the schematics and style for the given
board.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
The updated "i2c-gpio" driver bindings require to define the SDA and SCL
GPIO lines in the separate properties and mark both as GPIO_OPEN_DRAIN.
Covert all Exynos dts files to follow this style.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
GPIO lines for the CM36651 sensor I2C bus use the normal not the inverted
polarity. This bug has been there since adding the CM36651 sensor by
commit 85cb4e0bd229 ("ARM: dts: add cm36651 light/proximity sensor node
for exynos4412-trats2"), but went unnoticed because the "i2c-gpio"
driver ignored the GPIO polarity specified in the device-tree.
The recent conversion of "i2c-gpio" driver to the new, descriptor based
GPIO API, automatically made it the DT-specified polarity aware, what
broke the CM36651 sensor operation.
Fixes: 85cb4e0bd229 ("ARM: dts: add cm36651 light/proximity sensor node for exynos4412-trats2")
CC: stable@vger.kernel.org # 4.16+
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Add a node for BCM4330/3 SDIO chip on SDHCI bus #3 and the required MMC
power sequence node for the Exynos4210-based Trats board.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Add a node for the BCM43342A Bluetooth chip on the serial bus #0 on
the Exynos3250-based Rinato board.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Add devicetree file for the Exynos4210 based Galaxy S2 (GT-I9100
version).
Signed-off-by: Stenkin Evgeniy <stenkinevgeniy@gmail.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Add syscon mfd nodes for SB2 and SCPU Wrapper to RTD1195 DT.
Acked-by: James Tai <james.tai@realtek.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
Associate the UART nodes with the corresponding reset controller bits.
Acked-by: James Tai <james.tai@realtek.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
Add reset controller nodes for Realtek RTD1195 SoC.
Acked-by: James Tai <james.tai@realtek.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
Prepare a CRT syscon mfd node.
Acked-by: James Tai <james.tai@realtek.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
Group watchdog and UART0 into an Isolation syscon mfd node.
Group UART1 into a Miscellaneous syscon mfd node.
Cc: James Tai <james.tai@realtek.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
Add a Device Tree for Realtek's RTD1195 EVB "Horseradish".
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
Model Realtek's register bus in DT.
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
Carve out 0xa800 for the boot ROM from the /memory@0 node,
updating it to /memory@a800, and add it to /soc ranges.
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
Add Device Trees for Realtek RTD1195 SoC and MeLE X1000 TV box.
Reuse the existing RTD1295 watchdog compatible for now.
Reviewed-by: Rob Herring <robh@kernel.org>
[AF: Fixed r-bus size, fixed GIC, updated memreserve & memory]
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
This is required for wake on lan on i.MX6
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to wake from suspend by ethernet magic packets the GPC
must be used as intc does not have wakeup functionality.
But the FEC DT node currently uses interrupt-extended,
specificying intc, thus breaking WoL.
This problem is probably fallout from the stacked domain conversion
as intc used to chain to GPC.
So replace "interrupts-extended" by "interrupts" to use the default
parent which is GPC.
Fixes: b923ff6af0d5 ("ARM: imx6: convert GPC to stacked domains")
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull ARM devicetree updates from Arnd Bergmann:
"Most of the commits are for additional hardware support and minor
fixes for existing machines for all the usual platforms: qcom,
amlogic, at91, gemini, mediatek, ti, socfpga, i.mx, layerscape,
uniphier, rockchip, exynos, ux500, mvebu, tegra, stm32, renesas,
sunxi, broadcom, omap, and versatile.
The conversion of binding files to machine-readable yaml format
continues, along with fixes found during the validation. Andre
Przywara takes over maintainership for the old Calxeda Highbank
platform and provides a number of updates.
The OMAP2+ platforms see a continued move from platform data into dts
files, for many devices that relied on a mix of auxiliary data in
addition to the DT description
A moderate number of new SoCs and machines are added, here is a full
list:
- Two new Qualcomm SoCs with their evaluation boards: Snapdragon 865
(SM8250) is the current high-end phone chip, and IPQ6018 is a new
WiFi-6 router chip.
- Mediatek MT8516 application processor SoC for voice assistants,
along with the "pumpkin" development board
- NXP i.MX8M Plus SoC, a variant of the popular i.MX8M, along with an
evaluation board.
- Kontron "sl28" board family based on NXP LS1028A
- Eleven variations of the new i.MX6 TechNexion Pico board, combining
the "dwarf", "hobbit", "nymph" and "pi" baseboards with i.MX6/i.MX7
SoM carriers
- Three additional variants of the Toradex Colibri board family, all
based on versions of the NXP i.MX7.
- The Pinebook Pro laptop based on Rockchip RK3399
- Samsung S7710 Galaxy Xcover 2, a 2013 vintage Android phone based
on the ST-Ericsson u8500 platform
- DH Electronics DHCOM SoM and PDK2 rev. 400 carrier based on
STMicroelectronics stm32mp157
- Renesas M3ULCB starter kit for R-Car M3-W+
- Hoperun HiHope development board with Renesas RZ/G2M
- Pine64 PineTab tablet and PinePhone phone, both based on Allwinner
A64
- Linutronix Testbox v2 for the Lamobo R1 router, based on Allwinner
A20
- PocketBook Touch Lux 3 ebook reader, based on Allwinner A13"
* tag 'arm-dt-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (520 commits)
ARM: dts: ux500: Fix missing node renames
arm64: dts: Revert "specify console via command line"
MAINTAINERS: Update Calxeda Highbank maintainership
arm: dts: calxeda: Group port-phys and sgpio-gpio items
arm: dts: calxeda: Fix interrupt grouping
arm: dts: calxeda: Provide UART clock
arm: dts: calxeda: Basic DT file fixes
arm64: dts: specify console via command line
ARM: dts: at91: sama5d27_wlsom1_ek: add USB device node
ARM: dts: gemini: Add thermal zone to DIR-685
ARM: dts: gemini: Rename IDE nodes
ARM: socfpga: arria10: Add ptp_ref clock to ethernet nodes
arm64: dts: ti: k3-j721e-mcu: add scm node and phy-gmii-sel nodes
arm64: dts: ti: k3-am65-mcu: add phy-gmii-sel node
arm64: dts: ti: k3-am65-mcu: Add DMA entries for ADC
arm64: dts: ti: k3-am65-main: Add DMA entries for main_spi0
arm64: dts: ti: k3-j721e-mcu-wakeup: Add DMA entries for ADC
arm64: dts: ti: k3-am65: Add clocks to dwc3 nodes
arm64: dts: meson-g12b-odroid-n2: add SPIFC controller node
arm64: dts: khadas-vim3: add SPIFC controller node
...
|
|
Include originally "late" updates for OMAP and Qualcomm,
now that it's not late any more.
* arm/late: (122 commits)
ARM: OMAP2+: Drop legacy platform data for ti81xx edma
ARM: dts: Configure interconnect target module for ti816x edma
ARM: dts: Configure interconnect target module for dm814x tptc3
ARM: dts: Configure interconnect target module for dm814x tptc2
ARM: dts: Configure interconnect target module for dm814x tptc1
ARM: dts: Configure interconnect target module for dm814x tptc0
ARM: dts: Configure interconnect target module for dm814x tpcc
ARM: OMAP2+: Drop legacy platform data for dm814x cpsw
ARM: dts: Configure interconnect target module for dm814x cpsw
clk: ti: Fix dm814x clkctrl for ethernet
arm64: dts: qcom: sdm845-mtp: Relocate remoteproc firmware
arm64: dts: sdm845: add IPA information
arm64: dts: qcom: db845c: add analog audio support
arm64: dts: qcom: sdm845: add pinctrl nodes for quat i2s
arm64: dts: qcom: c630: Enable audio support
arm64: dts: qcom: sdm845: add apr nodes
arm64: dts: qcom: sdm845: add slimbus nodes
arm64: dts: qcom: sc7180: Update reg names for SDHC
arm64: dts: qcom: qcs404: Enable CQE support for eMMC
arm64: dts: msm8916: Add fastrpc node
...
|
|
Pull SPDX updates from Greg KH:
"Here are three SPDX patches for 5.7-rc1.
One fixes up the SPDX tag for a single driver, while the other two go
through the tree and add SPDX tags for all of the .gitignore files as
needed.
Nothing too complex, but you will get a merge conflict with your
current tree, that should be trivial to handle (one file modified by
two things, one file deleted.)
All three of these have been in linux-next for a while, with no
reported issues other than the merge conflict"
* tag 'spdx-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx:
ASoC: MT6660: make spdxcheck.py happy
.gitignore: add SPDX License Identifier
.gitignore: remove too obvious comments
|
|
Pull ARM updates from Russell King:
- replace setup_irq() with request_irq() for ebsa110, footbridge, rpc
- fix clang assembly error in kexec code
- remove .fixup section in boot stub
- decompressor / EFI cache flushing updates
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8966/1: rpc: replace setup_irq() by request_irq()
ARM: 8965/2: footbridge: replace setup_irq() by request_irq()
ARM: 8964/1: ebsa110: replace setup_irq() by request_irq()
ARM: 8962/1: kexec: drop invalid assembly argument
ARM: decompressor: switch to by-VA cache maintenance for v7 cores
ARM: decompressor: prepare cache_clean_flush for doing by-VA maintenance
ARM: decompressor: factor out routine to obtain the inflated image size
ARM: 8959/1: Remove unused .fixup section in boot stub
ARM: allow unwinder to unwind recursive functions
|
|
Pull devicetree updates from Rob Herring:
- Unit test for overlays with GPIO hogs
- Improve dma-ranges parsing to handle dma-ranges with multiple entries
- Update dtc to upstream version v1.6.0-2-g87a656ae5ff9
- Improve overlay error reporting
- Device link support for power-domains and hwlocks bindings
- Add vendor prefixes for Beacon, Topwise, ENE, Dell, SG Micro, Elida,
PocketBook, Xiaomi, Linutronix, OzzMaker, Waveshare Electronics, and
ITE Tech
- Add deprecated Marvell vendor prefix 'mrvl'
- A bunch of binding conversions to DT schema continues. Of note, the
common serial and USB connector bindings are converted.
- Add more Arm CPU compatibles
- Drop Mark Rutland as DT maintainer :(
* tag 'devicetree-for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (106 commits)
MAINTAINERS: drop an old reference to stm32 pwm timers doc
MAINTAINERS: dt: update etnaviv file reference
dt-bindings: usb: dwc2: fix bindings for amlogic, meson-gxbb-usb
dt-bindings: uniphier-system-bus: fix warning in the example
dt-bindings: display: meson-vpu: fix indentation of reg-names' "items"
dt-bindings: iio: Fix adi, ltc2983 uint64-matrix schema constraints
dt-bindings: power: Fix example for power-domain
dt-bindings: arm: Add some constraints for PSCI nodes
of: some unittest overlays not untracked
of: gpio unittest kfree() wrong object
dt-bindings: phy: convert phy-rockchip-inno-usb2 bindings to yaml
dt-bindings: serial: sh-sci: Convert to json-schema
dt-bindings: serial: Document serialN aliases
dt-bindings: thermal: tsens: Set 'additionalProperties: false'
dt-bindings: thermal: tsens: Fix nvmem-cell-names schema
dt-bindings: vendor-prefixes: Add Beacon vendor prefix
dt-bindings: vendor-prefixes: Add Topwise
of: of_private.h: Replace zero-length array with flexible-array member
docs: dt: fix a broken reference to input.yaml
docs: dt: fix references to ap806-system-controller.txt
...
|
|
|
|
Pull networking updates from David Miller:
"Highlights:
1) Fix the iwlwifi regression, from Johannes Berg.
2) Support BSS coloring and 802.11 encapsulation offloading in
hardware, from John Crispin.
3) Fix some potential Spectre issues in qtnfmac, from Sergey
Matyukevich.
4) Add TTL decrement action to openvswitch, from Matteo Croce.
5) Allow paralleization through flow_action setup by not taking the
RTNL mutex, from Vlad Buslov.
6) A lot of zero-length array to flexible-array conversions, from
Gustavo A. R. Silva.
7) Align XDP statistics names across several drivers for consistency,
from Lorenzo Bianconi.
8) Add various pieces of infrastructure for offloading conntrack, and
make use of it in mlx5 driver, from Paul Blakey.
9) Allow using listening sockets in BPF sockmap, from Jakub Sitnicki.
10) Lots of parallelization improvements during configuration changes
in mlxsw driver, from Ido Schimmel.
11) Add support to devlink for generic packet traps, which report
packets dropped during ACL processing. And use them in mlxsw
driver. From Jiri Pirko.
12) Support bcmgenet on ACPI, from Jeremy Linton.
13) Make BPF compatible with RT, from Thomas Gleixnet, Alexei
Starovoitov, and your's truly.
14) Support XDP meta-data in virtio_net, from Yuya Kusakabe.
15) Fix sysfs permissions when network devices change namespaces, from
Christian Brauner.
16) Add a flags element to ethtool_ops so that drivers can more simply
indicate which coalescing parameters they actually support, and
therefore the generic layer can validate the user's ethtool
request. Use this in all drivers, from Jakub Kicinski.
17) Offload FIFO qdisc in mlxsw, from Petr Machata.
18) Support UDP sockets in sockmap, from Lorenz Bauer.
19) Fix stretch ACK bugs in several TCP congestion control modules,
from Pengcheng Yang.
20) Support virtual functiosn in octeontx2 driver, from Tomasz
Duszynski.
21) Add region operations for devlink and use it in ice driver to dump
NVM contents, from Jacob Keller.
22) Add support for hw offload of MACSEC, from Antoine Tenart.
23) Add support for BPF programs that can be attached to LSM hooks,
from KP Singh.
24) Support for multiple paths, path managers, and counters in MPTCP.
From Peter Krystad, Paolo Abeni, Florian Westphal, Davide Caratti,
and others.
25) More progress on adding the netlink interface to ethtool, from
Michal Kubecek"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2121 commits)
net: ipv6: rpl_iptunnel: Fix potential memory leak in rpl_do_srh_inline
cxgb4/chcr: nic-tls stats in ethtool
net: dsa: fix oops while probing Marvell DSA switches
net/bpfilter: remove superfluous testing message
net: macb: Fix handling of fixed-link node
net: dsa: ksz: Select KSZ protocol tag
netdevsim: dev: Fix memory leak in nsim_dev_take_snapshot_write
net: stmmac: add EHL 2.5Gbps PCI info and PCI ID
net: stmmac: add EHL PSE0 & PSE1 1Gbps PCI info and PCI ID
net: stmmac: create dwmac-intel.c to contain all Intel platform
net: dsa: bcm_sf2: Support specifying VLAN tag egress rule
net: dsa: bcm_sf2: Add support for matching VLAN TCI
net: dsa: bcm_sf2: Move writing of CFP_DATA(5) into slicing functions
net: dsa: bcm_sf2: Check earlier for FLOW_EXT and FLOW_MAC_EXT
net: dsa: bcm_sf2: Disable learning for ASP port
net: dsa: b53: Deny enslaving port 7 for 7278 into a bridge
net: dsa: b53: Prevent tagged VLAN on port 7 for 7278
net: dsa: b53: Restore VLAN entries upon (re)configuration
net: dsa: bcm_sf2: Fix overflow checks
hv_netvsc: Remove unnecessary round_up for recv_completion_cnt
...
|
|
Pull tty/serial updates from Greg KH:
"Here is the big set of TTY / Serial patches for 5.7-rc1
Lots of console fixups and reworking in here, serial core tweaks
(doesn't that ever get old, why are we still creating new serial
devices?), serial driver updates, line-protocol driver updates, and
some vt cleanups and fixes included in here as well.
All have been in linux-next with no reported issues"
* tag 'tty-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (161 commits)
serial: 8250: Optimize irq enable after console write
serial: 8250: Fix rs485 delay after console write
vt: vt_ioctl: fix use-after-free in vt_in_use()
vt: vt_ioctl: fix VT_DISALLOCATE freeing in-use virtual console
tty: serial: make SERIAL_SPRD depend on COMMON_CLK
tty: serial: fsl_lpuart: fix return value checking
tty: serial: fsl_lpuart: move dma_request_chan()
ARM: dts: tango4: Make /serial compatible with ns16550a
ARM: dts: mmp*: Make the serial ports compatible with xscale-uart
ARM: dts: mmp*: Fix serial port names
ARM: dts: mmp2-brownstone: Don't redeclare phandle references
ARM: dts: pxa*: Make the serial ports compatible with xscale-uart
ARM: dts: pxa*: Fix serial port names
ARM: dts: pxa*: Don't redeclare phandle references
serial: omap: drop unused dt-bindings header
serial: 8250: 8250_omap: Add DMA support for UARTs on K3 SoCs
serial: 8250: 8250_omap: Work around errata causing spurious IRQs with DMA
serial: 8250: 8250_omap: Extend driver data to pass FIFO trigger info
serial: 8250: 8250_omap: Move locking out from __dma_rx_do_complete()
serial: 8250: 8250_omap: Account for data in flight during DMA teardown
...
|
|
Pull EFI updates from Ingo Molnar:
"The EFI changes in this cycle are much larger than usual, for two
(positive) reasons:
- The GRUB project is showing signs of life again, resulting in the
introduction of the generic Linux/UEFI boot protocol, instead of
x86 specific hacks which are increasingly difficult to maintain.
There's hope that all future extensions will now go through that
boot protocol.
- Preparatory work for RISC-V EFI support.
The main changes are:
- Boot time GDT handling changes
- Simplify handling of EFI properties table on arm64
- Generic EFI stub cleanups, to improve command line handling, file
I/O, memory allocation, etc.
- Introduce a generic initrd loading method based on calling back
into the firmware, instead of relying on the x86 EFI handover
protocol or device tree.
- Introduce a mixed mode boot method that does not rely on the x86
EFI handover protocol either, and could potentially be adopted by
other architectures (if another one ever surfaces where one
execution mode is a superset of another)
- Clean up the contents of 'struct efi', and move out everything that
doesn't need to be stored there.
- Incorporate support for UEFI spec v2.8A changes that permit
firmware implementations to return EFI_UNSUPPORTED from UEFI
runtime services at OS runtime, and expose a mask of which ones are
supported or unsupported via a configuration table.
- Partial fix for the lack of by-VA cache maintenance in the
decompressor on 32-bit ARM.
- Changes to load device firmware from EFI boot service memory
regions
- Various documentation updates and minor code cleanups and fixes"
* 'efi-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (114 commits)
efi/libstub/arm: Fix spurious message that an initrd was loaded
efi/libstub/arm64: Avoid image_base value from efi_loaded_image
partitions/efi: Fix partition name parsing in GUID partition entry
efi/x86: Fix cast of image argument
efi/libstub/x86: Use ULONG_MAX as upper bound for all allocations
efi: Fix a mistype in comments mentioning efivar_entry_iter_begin()
efi/libstub: Avoid linking libstub/lib-ksyms.o into vmlinux
efi/x86: Preserve %ebx correctly in efi_set_virtual_address_map()
efi/x86: Ignore the memory attributes table on i386
efi/x86: Don't relocate the kernel unless necessary
efi/x86: Remove extra headroom for setup block
efi/x86: Add kernel preferred address to PE header
efi/x86: Decompress at start of PE image load address
x86/boot/compressed/32: Save the output address instead of recalculating it
efi/libstub/x86: Deal with exit() boot service returning
x86/boot: Use unsigned comparison for addresses
efi/x86: Avoid using code32_start
efi/x86: Make efi32_pe_entry() more readable
efi/x86: Respect 32-bit ABI in efi32_pe_entry()
efi/x86: Annotate the LOADED_IMAGE_PROTOCOL_GUID with SYM_DATA
...
|
|
Pull USB / PHY updates from Greg KH:
"Here are the big set of USB and PHY driver patches for 5.7-rc1.
Nothing huge here, some new PHY drivers, loads of USB gadget fixes and
updates, xhci updates, usb-serial driver updates and new device ids,
and other minor things. Full details in the shortlog.
All have been in linux-next for a while with no reported issues"
* tag 'usb-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (239 commits)
USB: cdc-acm: restore capability check order
usb: cdns3: make signed 1 bit bitfields unsigned
usb: gadget: fsl: remove unused variable 'driver_desc'
usb: gadget: f_fs: Fix use after free issue as part of queue failure
usb: typec: Correct the documentation for typec_cable_put()
USB: serial: io_edgeport: fix slab-out-of-bounds read in edge_interrupt_callback
USB: serial: option: add Wistron Neweb D19Q1
USB: serial: option: add BroadMobi BM806U
USB: serial: option: add support for ASKEY WWHC050
usb: core: Add ACPI support for USB interface devices
driver core: platform: Reimplement devm_platform_ioremap_resource
usb: dwc2: convert to devm_platform_get_and_ioremap_resource
usb: host: hisilicon: convert to devm_platform_get_and_ioremap_resource
usb: host: xhci-plat: convert to devm_platform_get_and_ioremap_resource
drivers: provide devm_platform_get_and_ioremap_resource()
phy: qcom-qusb2: Add new overriding tuning parameters in QUSB2 V2 PHY
phy: qcom-qusb2: Add support for overriding tuning parameters in QUSB2 V2 PHY
dt-bindings: phy: qcom-qusb2: Add support for overriding Phy tuning parameters
phy: qcom-qusb2: Add generic QUSB2 V2 PHY support
dt-bindings: phy: qcom,qusb2: Add compatibles for QUSB2 V2 phy and SC7180
...
|
|
Until now a PHY-fixup in mach-imx set our rgmii timing correctly. For
the PHY KSZ9131 there is no PHY-fixup in mach-imx. To support this PHY
too, use rgmii-id.
For the now used KSZ9031 nothing will change, as rgmii-id is only
implemented and supported by the KSZ9131.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull ARM DT and driver fixes from Arnd Bergmann:
"For the devicetree files, there are a total of 20 patches, almost
entirely for 32-bit machines:
- The Allwinner/sun9i r40 SoC dtsi file contains a number of issues,
both for correctness and for style that are addressed in separate
patches. This causes most of the changed lines of the DT updates
this time.
- More Allwinner updates fixing the identification of the security
system on sun8i/A33, a recent regression of the A83t ethernet, and
a few board specific issues on the TBS-A711 macine.
- Several bug fixes for OMAP dts files, most notably fixing the
timings for the NAND flash on the Nokia N900 that regressed a while
ago after the move to configuring them from DT. Some other OMAPs
now set the correct dma limits on the L3 bus, and a regression fix
addresses lost Ethernet on dm814x
- One incorrect setting in the newly added Raspberry Pi Zero W that
may cause issues with the SD card controller.
- A missing property on the bcm2835 firmware node caused incorrect
DMA settings.
- An old bug on the oxnas platform causing spurious interrupts is
finally addressed.
- A regression on the Exynos Midas board broke the OLED panel power
supply.
- The i.MX6 phycore SoM specified the wrong voltage for the SoC, this
is now set to the values from the datasheet.
- Some 64-bit machines use a deprecated string to identify the PSCI
firmware.
There are also several small code fixes addressing mostly serious
issues:
- Fix the sunxi rsb bus access to no longer return incorrect data
when mixing 8 and 16 bit I/O.
- Fix a suspend/resume regression on the OMAP2+ lcdc from a missing
quirk in the ti-sysc driver
- Fix a NULL pointer access from a race in the fsl dpio driver
- Fix a v5.5 regression in the exynos-chipid driver that caused an
invalid error code probing the device on non-exynos platforms
- Fix an out-of-bounds access in the AMD TEE driver"
* tag 'arm-soc-fixes-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (24 commits)
soc: samsung: chipid: Fix return value on non-Exynos platforms
arm64: dts: Fix leftover entry-methods for PSCI
ARM: dts: exynos: Fix regulator node aliasing on Midas-based boards
ARM: dts: oxnas: Fix clear-mask property
ARM: dts: bcm283x: Fix vc4's firmware bus DMA limitations
ARM: dts: omap5: Add bus_dma_limit for L3 bus
ARM: dts: omap4-droid4: Fix lost touchscreen interrupts
ARM: dts: dra7: Add bus_dma_limit for L3 bus
ARM: bcm2835-rpi-zero-w: Add missing pinctrl name
ARM: dts: sun8i: a33: add the new SS compatible
dt-bindings: crypto: add new compatible for A33 SS
ARM: dts: sun8i: r40: Move SPI device nodes based on address order
ARM: dts: sun8i: r40: Fix register base address for SPI2 and SPI3
ARM: dts: sun8i: r40: Move AHCI device node based on address order
ARM: dts: imx6: phycore-som: fix arm and soc minimum voltage
soc: fsl: dpio: register dpio irq handlers after dpio create
tee: amdtee: out of bounds read in find_session()
ARM: dts: N900: fix onenand timings
bus: ti-sysc: Fix quirk flags for lcdc on am335x
ARM: dts: Fix dm814x Ethernet by changing to use rgmii-id mode
...
|
|
With the introduction of 55c7c0621078 ("ARM: dts: bcm283x: Fix vc4's
firmware bus DMA limitations") the firmware bus has to comply with
/soc's DMA limitations. Ultimately linking both buses to a same
dma-ranges property. The patch (and author) missed the fact that a bus'
#address-cells and #size-cells properties are not inherited, but set to
a fixed value which, in this case, doesn't match /soc's. This, although
not breaking Linux's DMA mapping functionality, generates ugly dtc
warnings.
Fix the issue by adding the correct address and size cells properties
under the firmware bus.
Fixes: 55c7c0621078 ("ARM: dts: bcm283x: Fix vc4's firmware bus DMA limitations")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20200326134413.12298-1-nsaenzjulienne@suse.de
|
|
The register based driver turned out to be unstable, specially on RPi3a+
but not limited to it. While a fix is being worked on, we roll back to
using firmware based scheme.
Fixes: e1dc2b2e1bef ("ARM: bcm283x: Switch V3D over to using the PM driver instead of firmware")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/20200303173217.3987-1-nsaenzjulienne@suse.de
|
|
The SD card power can be controlled trough a pin routed into the board's
external GPIO expander. Turn that into a regulator and provide it to
emmc2.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20200306174413.20634-12-nsaenzjulienne@suse.de
|
|
The 6th line of the GPIO expander is used to power the board's SD card.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20200306174413.20634-11-nsaenzjulienne@suse.de
|
|
I renamed the dsi-nodes from dsi@ to dsi-controller@
so that the schema check would kick in, but missed to
rename it in a few places.
Link: https://lore.kernel.org/r/20200326222536.86441-1-linus.walleij@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Like on N900, we cannot access RNG directly on N950/N9. Mark it disabled in
the DTS to allow kernel to boot.
Fixes: 308607e5545f ("ARM: dts: Configure omap3 rng")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Drop remaining legacy platform data for cpsw and edma
With a non-critical clock fix for dm814x ethernet, we can update ti81xx
for cpsw ethernet and edma to probe them with ti-sysc interconnect
target module driver and device tree data. And we can drop the related
remaining platform data for cpsw and edma.
* tag 'omap-for-v5.7/ti-sysc-drop-pdata-ti81xx-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Drop legacy platform data for ti81xx edma
ARM: dts: Configure interconnect target module for ti816x edma
ARM: dts: Configure interconnect target module for dm814x tptc3
ARM: dts: Configure interconnect target module for dm814x tptc2
ARM: dts: Configure interconnect target module for dm814x tptc1
ARM: dts: Configure interconnect target module for dm814x tptc0
ARM: dts: Configure interconnect target module for dm814x tpcc
ARM: OMAP2+: Drop legacy platform data for dm814x cpsw
ARM: dts: Configure interconnect target module for dm814x cpsw
clk: ti: Fix dm814x clkctrl for ethernet
Link: https://lore.kernel.org/r/pull-1584575307-189595@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Drop legacy platform data for omaps for v5.7
This series of changes continues dropping legacy platform data for
omaps by updating devices to probe with ti-sysc interconnect target
module driver:
- Update omap4, omap5, am437x, and dra7 display subsystem (DSS)
to probe with device tree data only
- Update am335x, am437x and dra7 to probe EDMA to probe with
device tree data only
- Drop legacy platform data for am335x and am437x PRUSS as the
current code just keeps the devices in reset
- Drop legacy platform data for omap4 DSP and IPU as the current
code just keeps the devices in reset
- Configure am437x and dra7 PRU-ICSS to probe with device tree
data
For the dropped omap4 DSP and IPU platform data, there will be patches
coming later on to configure the accelerators using the omap remoteproc
bindings so hopefully folks can actually use these devices eventually.
* tag 'omap-for-v5.7/ti-sysc-drop-pdata-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (56 commits)
ARM: OMAP2+: Drop legacy platform data for dra7 edma
ARM: OMAP2+: Drop legacy platform data for am3 and am4 edma
ARM: dts: Configure interconnect target module for dra7 tptc1
ARM: dts: Configure interconnect target module for dra7 tptc0
ARM: dts: Configure interconnect target module for dra7 tpcc
ARM: dts: Configure interconnect target module for am4 tptc2
ARM: dts: Configure interconnect target module for am4 tptc1
ARM: dts: Configure interconnect target module for am4 tptc0
ARM: dts: Configure interconnect target module for am4 tpcc
ARM: dts: Configure interconnect target module for am3 tptc2
ARM: dts: Configure interconnect target module for am3 tptc1
ARM: dts: Configure interconnect target module for am3 tptc0
ARM: dts: Configure interconnect target module for am3 tpcc
ARM: dts: dra7: Add PRU-ICSS interconnect target-module nodes
ARM: dts: AM4372: Add the PRU-ICSS interconnect target-module node
ARM: dts: AM33xx-l4: Update PRUSS interconnect target-module node
ARM: OMAP2+: Drop legacy platform data for am437x DSS
ARM: OMAP2+: Drop legacy platform data for dra7 DSS
ARM: OMAP2+: Drop legacy platform data for omap5 DSS
ARM: OMAP2+: Drop legacy platform data for omap4 dss
...
Link: https://lore.kernel.org/r/pull-1583858385-416921@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
For proper bindings checks we need to properly group the port-phys and
sgpio-gpio items, so that they match the expected number of items.
Link: https://lore.kernel.org/r/20200228135106.220620-5-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Currently multiple interrupts for some devices are written as one array
instead of using the DT grouping notation (<0 42 4>, <0 23 4>).
This ends up in the same binary representation in the .dtb, but is
semantically not equivalent. The yaml schema checks will stumble over
this, so lets fix that first.
I refrained from using the symbolic names for GIC_SPI/GIC_PPI and
IRQ_TYPE_LEVEL_HIGH, mostly because it increases the delta between the
original DTS files and the mainline versions, so it's just additional
churn.
Link: https://lore.kernel.org/r/20200228135106.220620-4-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The PL011 UART binding requires two clocks to be named in a node.
Add the second clock, which is the bus gate, that just gets enabled.
Since this is a fixed clock anyway, it doesn't make any difference.
Link: https://lore.kernel.org/r/20200228135106.220620-3-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The .dts files for the Calxeda machines are quite old, so carry some
sloppy mistakes that the DT schema checker will complain about.
Fix those issues, they should not have any effect on functionality.
Link: https://lore.kernel.org/r/20200228135106.220620-2-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Qualcomm ARM dts updates for v5.7
This adds Bluetooth support on Nexus 5, USB on Xperia Z1 and defines
gpio-ranges throughout the various gpio-controllers.
* tag 'qcom-dts-for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
ARM: dts: qcom: add gpio-ranges property
ARM: dts: qcom: msm8974-hammerhead: add support for bluetooth
ARM: dts: qcom: msm8974: add blsp2_uart10
ARM: dts: qcom: msm8974-honami: Add USB node.
Link: https://lore.kernel.org/r/20200318044305.GE470201@yoga
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
SoCFPGA DTS updates for v5.7, part 2
- Add ptp_ref clock to ethernet nodes for Arria10
* tag 'socfpga_dts_update_for_v5.7_part2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: socfpga: arria10: Add ptp_ref clock to ethernet nodes
Link: https://lore.kernel.org/r/20200325160745.793-1-dinguyen@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
AT91 DT for 5.7
- Enable watchdog on sam9x60
- Correct sama5d4/2 RTC compatibles
- Add i2c gpio pinctrl to allow i2c recovery
* tag 'at91-5.7-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: at91: sama5d27_wlsom1_ek: add USB device node
ARM: dts: at91: sama5d2: add i2c gpio pinctrl
ARM: dts: at91: sama5d4: add i2c gpio pinctrl
ARM: dts: at91: sama5d3: add i2c gpio pinctrl
ARM: dts: at91: sama5d4: use correct rtc compatible
ARM: dts: at91: sama5d2: use correct rtc compatible
ARM: dts: at91: sam9x60ek: enable watchdog node
ARM: dts: at91: sam9x60: add watchdog node
ARM: dts: at91: Kill off "simple-panel" compatibles
Link: https://lore.kernel.org/r/20200322085931.GA208770@piout.net
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
Alexandre Belloni
Marek Szyprowski
Stenkin Evgeniy
Andreas Färber
Martin Fuzzey
Linus Torvalds
Arnd Bergmann
Russell King
Philippe Schenker
Nicolas Saenz Julienne
Linus Walleij
Aaro Koskinen
Andre Przywara