| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Qualcomm ARM64 DTS updates for 6.1
Support for Samsung Galaxy E5, E7 and Grand Max is added, with support
for both 32-bit and 64-bit variants. The Samsung Galaxy S4 Mini Value
Edition gains magnetometer support.
MSM8996-based Xiaomi devices gains descriptions of the LPG-based LEDs.
On SA8295P ADP problems arising from regulators being switched into
low-power mode is worked around by removing this ability, for now.
The onboard USB Hub on SC7180 Trogdor is finally described and a few ADC
related updates are introduced.
On SC7280 support for the CPU and LLC bwmon instances are introduced.
Soundwire, audio codecs and sound introduced for a variety of boards.
Using required-opps the USB controllers votes for a minimum corner on
VDD_CX.
The onboard USB Hub Herobrine is described. A new board, the Google
Evoker is added, as is another revision of Herobrine Villager.
On SC8280XP the USB controllers are marked as wakeup-sources, to keep
them powered during suspend. The CRD has HID devices marked as
wakeup-sources to enable resuming the system. In addition to these
changes the alternative touchpad is introduced on the Lenovo ThinkPad
X13s.
SDM845 gains RPMh stats support and the LLCC BWMON is added. For SM6350
interconnect providers and GPI DMA is introduced. A description of the
PM7280b PMIC is added to Fairphone FP4 on SM7225.
With the multi-MSI support added in the PCIe controller, SM8250 gets all
its MSI interrupts added.
UFS ICE and the second SDHCI controller is introduced on SM8450. Support
for the Sony Xperia 1 IV is introduced.
Throughout a variety of platforms the TCSR mutex syscon is replaced with
the MMIO-based binding. TCSR nodes gained proper compatibles and halt
syscon nodes are split out from the mutex ranges.
A range of fixes to align with DT bindings are introduced. Among these
are the changes to the follow the TLMM binding and suffix pinctrl states
with -state and subnodes thereof with -pins, another is a number of
changes transitioning to use -gpios and introduction of proper parent
clock references in various clock providers.
* tag 'qcom-arm64-for-6.1' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (136 commits)
arm64: dts: qcom: sc7280: Add required-opps for USB
arm64: dts: qcom: sm8450: fix UFS PHY serdes size
arm64: dts: qcom: ipq8074: fix PCIe PHY serdes size
arm64: dts: qcom: sa8295p-adp: add missing gpio-ranges in PMIC GPIOs
arm64: dts: qcom: sa8295p-adp: add fallback compatible to PMIC GPIOs
arm64: dts: qcom: msm8996-xiaomi: align PMIC GPIO pin configuration with DT schema
arm64: dts: qcom: msm8994-msft-lumia-octagon: align resin node name with bindings
arm64: dts: qcom: pmi8994: add missing MPP compatible fallback
dt-bindings: pci: QCOM Add missing sc7280 aggre0, aggre1 clocks
arm64: dts: qcom: sc7280: Add missing aggre0, aggre1 clocks
arm64: dts: qcom: sc7280-villager: Adjust LTE SKUs
dt-bindings: arm: qcom: Adjust LTE SKUs for sc7280-villager
arm64: dts: qcom: sc7280-herobrine: Add nodes for onboard USB hub
arm64: dts: qcom: sc7180-trogdor: Add nodes for onboard USB hub
arm64: dts: qcom: align SDHCI reg-names with DT schema
arm64: dts: qcom: sm8250: provide additional MSI interrupts
arm64: dts: qcom: msm8996: add #clock-cells and XO clock to the HDMI PHY node
arm64: dts: qcom: Use WCD9335 DT bindings
arm64: dts: qcom: msm8994: switch TCSR mutex to MMIO
arm64: dts: qcom: ipq6018: switch TCSR mutex to MMIO
...
Link: https://lore.kernel.org/r/20220921234854.1343238-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Qualcomm ARM DTS updates for 6.1
This adds extends the IPQ8064 support with the two variants IPQ8062 and
IPQ8065. MSM8974 and APQ8084 gained RPM stats support.
The Audio DSP remoteproc was added to MSM8226 and enabled for ASUS
ZenWatch 2 and LG G Watch R.
MSM8660 gained one I2C and one SPI bus and the APQ8060 Dragonboard got
the TMA340 Touchscreen described.
A wide range of improvements are done throughout the DTS files to align
with bindings, fix issues and improve structure on things.
* tag 'qcom-dts-for-6.1' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (35 commits)
ARM: dts: qcom: apq8026-lg-lenok: Enable ADSP
ARM: dts: qcom: apq8026-asus-sparrow: Enable ADSP
ARM: dts: qcom: msm8226: Add ADSP node
ARM: dts: qcom: ipq8064: pad addresses to 8 digit
ARM: dts: qcom: ipq8064: reorganize node order and sort them
ARM: dts: qcom: align SDHCI clocks with DT schema
ARM: dts: qcom: align SDHCI reg-names with DT schema
ARM: dts: qcom: msm8960: add clocks to the MMCC device node
ARM: dts: qcom: apq8064: add clocks to the MMCC device node
ARM: dts: qcom: msm8960: add clocks to the GCC device node
ARM: dts: qcom: apq8064: add clocks to the GCC device node
ARM: dts: qcom: msm8960: add clocks to the LCC device node
ARM: dts: qcom: apq8064: add clocks to the LCC device node
ARM: dts: qcom: msm8226: switch TCSR mutex to MMIO
ARM: dts: qcom: apq8084: switch TCSR mutex to MMIO
ARM: dts: qcom: msm8660: fix node names for fixed clocks
ARM: dts: qcom: msm8660: add pxo/cxo clocks to the GCC node
ARM: dts: qcom: apq8060-dragonboard: Add TMA340 to APQ8060 DragonBoard
ARM: dts: qcom: msm8660: Add GSBI3 I2C bus
ARM: dts: qcom: msm8660: Add GSBI1 SPI bus
...
Link: https://lore.kernel.org/r/20220921222619.1338380-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Renesas ARM DT updates for v6.1 (take two)
- Merge Renesas ARM/ARM64 maintainers entries,
- CAN support for the RZ/N1 SoC and the RZN1D-DB development board,
- Watchdog, pin control, I2C (EEPROM), GPIO (LEDS/switches), and
Ethernet support for the R-Car V4H SoC and the White Hawk
development board,
- Miscellaneous fixes and improvements.
* tag 'renesas-arm-dt-for-v6.1-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: (26 commits)
arm64: dts: renesas: Adjust whitespace around '{'
arm64: dts: renesas: rzg2ul-smarc: Include SoM DTSI into board DTS
arm64: dts: renesas: rzg2ul-smarc-som: Drop enabling wdt2
ARM: dts: renesas: Fix USB PHY device and child node names
arm64: dts: renesas: r8a779a0: Update to R-Car Gen4 compatible values
arm64: dts: renesas: white-hawk-cpu: Add missing bootargs
arm64: dts: renesas: spider-cpu: Add missing bootargs
arm64: dts: renesas: spider: Move aliases and chosen
arm64: dts: renesas: white-hawk-cpu: Add Ethernet support
arm64: dts: renesas: white-hawk: Move aliases and chosen
arm64: dts: renesas: r8a779g0: Add RAVB nodes
arm64: dts: renesas: white-hawk-cpu: Add push switches
arm64: dts: renesas: white-hawk-cpu: Add GP LEDs
arm64: dts: renesas: r8a779g0: Add GPIO nodes
arm64: dts: renesas: white-hawk: Add Ethernet sub-board
arm64: dts: renesas: white-hawk: Add CSI/DSI sub-board
arm64: dts: renesas: white-hawk: Add I2C0 and EEPROMs
arm64: dts: renesas: r8a779g0: Add I2C nodes
arm64: dts: renesas: white-hawk-cpu: Add serial port pin control
arm64: dts: renesas: r8a779g0: Add pinctrl device node
...
Link: https://lore.kernel.org/r/cover.1663588776.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The DT parser is dependent on the PCI device being tagged as
device_type = "pci" in order to parse memory ranges properly.
Fix this up.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220919092608.813511-1-linus.walleij@linaro.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
i.MX device tree change for 6.1
- A series from Alexander Stein to add missing properties for i.MX6 SRAM.
- Drop 'interrupts' property when 'interrupts-extended' is present. This
fixes a dtbs_check warning with i.MX6 DT.
- Update device trees to use generic name 'dma-controller' for SDMA.
- A set of changes from Krzysztof Kozlowski to align SPI, LED and
gpio-keys node name with dtschema.
- A series of indentation and white-space cleanups from Marcel Ziswiler
to address various checkpatch warnings.
- Add DDR pinmux defines to VF610 DT header.
- A couple of changes from Peng Fan to update clock-names and add IPG
clock for i.MX7ULP LPI2C devices.
- Improve device tree structure for Kontron i.MX6UL/ULL based boards.
- A series of changes from Tim Harvey to add CAN regulator for Gateworks
i.MX6QDL boards.
- Various small and random board specific updates.
* tag 'imx-dt-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (40 commits)
ARM: dts: imx6qdl-gw54xx: add CAN regulator
ARM: dts: imx6qdl-gw53xx: add CAN regulator
ARM: dts: imx6qdl-gw52xx: add CAN regulator
ARM: dts: imx: update sdma node name format
ARM: dts: imx6: skov: migrate to resistive-adc-touch
ARM: dts: imx6sx-udoo-neo: don't use multiple blank lines
ARM: dts: imx6sl: use tabs for code indent
ARM: dts: imx6sx: add missing properties for sram
ARM: dts: imx6sll: add missing properties for sram
ARM: dts: imx6sl: add missing properties for sram
ARM: dts: imx6qp: add missing properties for sram
ARM: dts: imx6dl: add missing properties for sram
ARM: dts: imx6q: add missing properties for sram
ARM: dts: imx7ulp: Add IPG clock for lpi2c
ARM: dts: imx7ulp: update the LPI2C clock-names
ARM: dts: vf610: ddr pinmux
ARM: dts: imx6qdl-dhcom: Move IPU iomux node from PDK2 to SoM file
ARM: dts: imx6ul-kontron: Add imx6ull-kontron-bl to Makefile
ARM: dts: imx6ul-kontron: Simplify devicetree structure
ARM: dts: vf610: align SPI node name with dtschema
...
Link: https://lore.kernel.org/r/20220918092806.2152700-3-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Two fixes for omaps
A fix to remove usb4 from am5748 as it does not exist on the SoC, and
a fix for am335x mmc dma that wired direct and should not use the xbar.
Note that the am5748 fix depends on the recent deferred probe regression
fixes to boot. I ended up picking the merge commit to base it on as it
describes what got fixed quite nicely rather than a -rc tag.
* tag 'omap-for-6.0/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am5748: keep usb4_tm disabled
ARM: dts: am33xx: Fix MMCHS0 dma properties
Link: https://lore.kernel.org/r/pull-1663140667-273537@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This patch fixes the following build error:
In file included from ./include/linux/io.h:13,
from ./arch/arm/mach-rpc/include/mach/uncompress.h:9,
from arch/arm/boot/compressed/misc.c:31:
./arch/arm/include/asm/io.h:85:22: error: conflicting types for ‘__raw_writeb’
85 | #define __raw_writeb __raw_writeb
| ^~~~~~~~~~~~
./arch/arm/include/asm/io.h:86:20: note: in expansion of macro ‘__raw_writeb’
86 | static inline void __raw_writeb(u8 val, volatile void __iomem *addr)
| ^~~~~~~~~~~~
In file included from arch/arm/boot/compressed/misc.c:26:
arch/arm/boot/compressed/misc-ep93xx.h:13:20: note: previous definition of ‘__raw_writeb’ was here
13 | static inline void __raw_writeb(unsigned char value, unsigned int ptr)
| ^~~~~~~~~~~~
To: Russell King <linux@armlinux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-arm-kernel@lists.infradead.org
Fixes: 0361c7e504b1 ("ARM: ep93xx: multiplatform support")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
The .data.rel.ro.local section has the same semantics as .data.rel.ro
here, so include it in the .rodata section of the decompressor.
Additionally since the .printk_index section isn't usable outside of
the core kernel, discard it in the decompressor. Avoids these warnings:
arm-linux-gnueabi-ld: warning: orphan section `.data.rel.ro.local' from `arch/arm/boot/compressed/fdt_rw.o' being placed in section `.data.rel.ro.local'
arm-linux-gnueabi-ld: warning: orphan section `.printk_index' from `arch/arm/boot/compressed/fdt_rw.o' being placed in section `.printk_index'
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/linux-mm/202209080545.qMIVj7YM-lkp@intel.com
Cc: Russell King <linux@armlinux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
make dtbs_check:
usb-phy@e6590100: '#phy-cells' is a required property
From schema: dtschema/schemas/phy/phy-provider.yaml
The R-Car Gen2 USB PHY device nodes do not represent USB PHYs
theirselves, and thus do not have "#phy-cells" properties. Fix the
warning by renaming them from "usb-phy" to "usb-phy-controller".
Rename their child nodes from "usb-channel" to "usb-phy", as these do
represent USB PHYs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/6442b4042e26537abc8632c4772f8201685f1f1f.1663165098.git.geert+renesas@glider.be
|
|
AT91 DT for v6.1 #2
It contains:
- new SAMA5D3 based board, namely SAMA5D3-EDS
- adjustments to pass the DT binding validations
- disable AES on some LAN966 based boards as they are reserverd by
secure OS
* tag 'at91-dt-6.1-2' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
spi: dt-bindings: atmel,at91rm9200-spi: Add DMA related properties
ARM: dts: at91: Add `atmel,usart-mode` required property to serial nodes
ARM: dts: at91: sam9x60ek: Add DBGU compatibles to uart1
ARM: dts: at91: sama7g5: Swap rx and tx for spi11
dts: arm: at91: Add SAMA5D3-EDS Board
dt-bindings: arm: at91: Add info on SAMA5D3-EDS
ARM: dts: lan966x: disable aes
Link: https://lore.kernel.org/r/20220916105407.1287452-1-claudiu.beznea@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The GW54xx has a transceiver with a STBY pin connected to an IMX6 GPIO.
Configure this as a regulator to drive it low when CAN is in use.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The GW53xx has a transceiver with a STBY pin connected to an IMX6 GPIO.
Configure this as a regulator to drive it low when CAN is in use.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The GW52xx has a transceiver with a STBY pin connected to an IMX6 GPIO.
Configure this as a regulator to drive it low when CAN is in use.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add the missing required DT property `atmel,usart-mode` to the serial
nodes of Atmel/Microchip DT files.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220913142205.162399-4-sergiu.moga@microchip.com
|
|
Maintain consistency among the compatibles of the serial nodes of
sam9x60ek and highlight the incremental characteristic of its serial
IP's by making sure that all serial nodes contain both the sam9x60
and sam9260 usart/dbgu compatibles.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220913142205.162399-3-sergiu.moga@microchip.com
|
|
Swap the rx and tx of the DMA related DT properties of the spi11 node
in order to maintain consistency across Microchip/Atmel SoC files.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220913142205.162399-2-sergiu.moga@microchip.com
|
|
This pull request contains Broadcom ARM-based SoC Device Tree updates
for 6.1, please pull the following:
- Rafal improves the BCM5301X PCIe DT nodes schema validation by
flagging the PCIe controller with a missing "device_type" property
- William merges BCM4908 within BCMBCA since this chip is part of the
Broadcom Broadband Carrier Access group and follows the architecture of
those chips
* tag 'arm-soc/for-6.1/devicetree' of https://github.com/Broadcom/stblinux:
arm64: bcmbca: Merge ARCH_BCM4908 to ARCH_BCMBCA
arm64: dts: Add BCM4908 generic board dts
arm64: dts: Move BCM4908 dts to bcmbca folder
arm64: dts: bcmbca: update BCM4908 board dts files
dt-bindings: arm64: bcmbca: Update BCM4908 description
dt-bindings: arm64: bcmbca: Merge BCM4908 into BCMBCA
ARM: dts: BCM5301X: Add basic PCI controller properties
Link: https://lore.kernel.org/r/20220915023044.2350782-2-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
AT91 fixes for 6.0 #2
It contains a fix for LAN966 SoCs that corrects the interrupt
number for internal PHYs.
* tag 'at91-fixes-6.0-2' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: lan966x: Fix the interrupt number for internal PHYs
Link: https://lore.kernel.org/r/20220915105833.4159850-1-claudiu.beznea@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Configure the reserved memory for ADSP and enable it.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220423155059.660387-5-luca@z3ntu.xyz
|
|
The customized reserved memory for ADSP is already configured, so we
just need to enable the node.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220423155059.660387-4-luca@z3ntu.xyz
|
|
Add a node for the adsp found on msm8226.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220423155059.660387-3-luca@z3ntu.xyz
|
|
Enable mac3 controller in Elbert dts: Elbert MAC3 is connected to the
BCM53134P onboard switch's IMP_RGMII port directly (fixed link, no PHY
between BMC MAC and BCM53134P).
Note: BMC's mdio0 controller is connected to BCM53134P's MDIO interface,
and the MDIO channel will be enabled later, when BCM53134 is added to
"bcm53xx" DSA driver.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The SAMA5D3-EDS board is an Ethernet Development Platform allowing for
evaluating many Microchip ethernet switch and PHY products. Various
daughter cards can connect via an RGMII connector or an RMII connector.
The EDS board is not intended for stand-alone use and has no ethernet
capabilities when no daughter board is connected. As such, this device
tree is intended to be used with a DT overlay defining the add-on board.
To better ensure consistency, some items are defined here as a form of
documentation so that all add-on overlays will use the same terms.
Link: https://www.microchip.com/en-us/development-tool/SAMA5D3-ETHERNET-DEVELOPMENT-SYSTEM
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
[claudiu.beznea: s/gpio-inputs/gpio-keys in at91-sama5d3_eds.dts]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220909163022.13022-2-jerry.ray@microchip.com
|
|
Disable AES node on lan966x pcb8290, pcb891 and pcb8309 because these
boards have lan966x that uses secure OS which reserves the AES block.
Therefore it can't be exposed to non-secure world.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220908070451.3730608-1-horatiu.vultur@microchip.com
|
|
Pad reg addresses to 8 digit to make sorting easier.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220718153815.29414-2-ansuelsmth@gmail.com
|
|
Reorganize node order and sort them by address.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220718153815.29414-1-ansuelsmth@gmail.com
|
|
The DT schema expects clocks iface-core order. No functional change.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220712144245.17417-6-krzysztof.kozlowski@linaro.org
|
|
DT schema requires SDHCI reg names to be hc/core without "_mem" suffix,
just like TXT bindings were expecting before the conversion.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220712144245.17417-5-krzysztof.kozlowski@linaro.org
|
|
As we are converting this platform to use DT clock bindings, add clocks
and clock-names properties to the MMCC device tree node.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: David Heidelberg <david@ixit.cz> # tested on Nexus 7 (2013)
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220623120418.250589-16-dmitry.baryshkov@linaro.org
|
|
As we are converting this platform to use DT clock bindings, add clocks
and clock-names properties to the MMCC device tree node.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: David Heidelberg <david@ixit.cz> # tested on Nexus 7 (2013)
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220623120418.250589-15-dmitry.baryshkov@linaro.org
|
|
As we are converting this platform to use DT clock bindings, add clocks
and clock-names properties to the GCC device tree node.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: David Heidelberg <david@ixit.cz> # tested on Nexus 7 (2013)
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220623120418.250589-14-dmitry.baryshkov@linaro.org
|
|
As we are converting this platform to use DT clock bindings, add clocks
and clock-names properties to the GCC device tree node.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: David Heidelberg <david@ixit.cz> # tested on Nexus 7 (2013)
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220623120418.250589-13-dmitry.baryshkov@linaro.org
|
|
As we are converting this platform to use DT clock bindings, add clocks
and clock-names properties to the LCC device tree node.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: David Heidelberg <david@ixit.cz> # tested on Nexus 7 (2013)
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220623120418.250589-12-dmitry.baryshkov@linaro.org
|
|
As we are converting this platform to use DT clock bindings, add clocks
and clock-names properties to the LCC device tree node.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: David Heidelberg <david@ixit.cz> # tested on Nexus 7 (2013)
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220623120418.250589-11-dmitry.baryshkov@linaro.org
|
|
The TCSR mutex bindings allow device to be described only with address
space (so it uses MMIO, not syscon regmap). This seems reasonable as
TCSR mutex is actually a dedicated IO address space and it also fixes DT
schema checks:
qcom-msm8226-samsung-s3ve3g.dtb: hwlock: 'reg' is a required property
qcom-msm8226-samsung-s3ve3g.dtb: hwlock: 'syscon' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220909092035.223915-16-krzysztof.kozlowski@linaro.org
|
|
The TCSR mutex bindings allow device to be described only with address
space (so it uses MMIO, not syscon regmap). This seems reasonable as
TCSR mutex is actually a dedicated IO address space and it also fixes DT
schema checks:
qcom-apq8084-mtp.dtb: hwlock: 'reg' is a required property
qcom-apq8084-mtp.dtb: hwlock: 'syscon' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220909092035.223915-15-krzysztof.kozlowski@linaro.org
|
|
Fix node names for three fixed clocks to follow the
no-underscores-in-name rule. To remain compatible with the drivers
expecting to find the old clock names, add clock-output-names
properties.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220909105136.3733919-6-dmitry.baryshkov@linaro.org
|
|
Add pxo/cxo clocks to the GCC device tree node.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220909105136.3733919-5-dmitry.baryshkov@linaro.org
|
|
This adds the CY8CTMA340 Touchscreen to the APQ8060 DragonBoard.
Tested without display by issuing cat /dev/input/input/event3
which produces appropriate noise and interrupts on the dedicated
GPIO line.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220913132846.305716-3-linus.walleij@linaro.org
|
|
GSBI3 can be used to enable an external I2C bus on e.g. the
APQ8060. On the DragonBoard APQ8060 this I2C bus is used to
talk to the Cypress CY8CTMA340 CYTTSP touchscreen.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220913132846.305716-2-linus.walleij@linaro.org
|
|
GSBI1 can be used to enable an external SPI bus on e.g. the
APQ8060. On the DragonBoard APQ8060 this SPI bus is used to
talk to the LCD display.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[bjorn: Moved status properties last]
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220913132846.305716-1-linus.walleij@linaro.org
|
|
According to the datasheet the interrupts for internal PHYs are
80 and 81.
Fixes: 6ad69e07def67c ("ARM: dts: lan966x: add MIIM nodes")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220912192629.461452-1-horatiu.vultur@microchip.com
|
|
STM32 DT for v6.1, round 1
Highlights:
----------
- MPU:
- General:
- Add I2C support (5 instances) on STM32MP13.
- Add SPI support (5 instabces) on STM32MP13.
- Add timer interrupts support on STM32MP15.
- ST boards:
- Enable I2C1 and I2C5 on stm32mp135f-dk board.
- Add SPI5 on stm32mp135f-dk board but disabled as only available on
the GPIO expansion connector.
- ARGON:
- Remove spidev node as not used by the code.
* tag 'stm32-dt-for-v6.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: argon: remove spidev node
ARM: dts: stm32: Create separate pinmux for qspi cs pin in stm32mp15-pinctrl.dtsi
ARM: dts: stm32: Fix typo in license text for Engicam boards
ARM: dts: stm32: Add timer interrupts on stm32mp15
ARM: dts: stm32: add pinctrl and disabled spi5 node in stm32mp135f-dk
ARM: dts: stm32: add spi nodes into stm32mp131.dtsi
ARM: dts: stm32: enable i2c1 and i2c5 on stm32mp135f-dk.dts
ARM: dts: stm32: add i2c nodes into stm32mp131.dtsi
Link: https://lore.kernel.org/r/d80afc20-2745-24a2-ab70-a5a03439bd50@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Adapt emac nodes to make them conform to the newly yaml-converted binding.
* tag 'v6.1-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: restyle emac nodes
ARM: dts: rockchip: fix rk3036 emac node compatible string
Link: https://lore.kernel.org/r/4766760.31r3eYUQgx@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Commit 956b200a846e ("spi: spidev: Warn loudly if instantiated from DT
as "spidev"") states that there should not be spidev nodes in DTs.
Remove this non-HW description. There won't be a regression because it
won't bind since 2015 anyhow.
Fixes: 16e3e44c5b87 ("ARM: dts: stm32: Add support for the emtrion emSBC-Argon")
Cc: Reinhold Mueller <reinhold.mueller@emtrion.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Create a separate pinmux for qspi chip select in stm32mp15-pinctrl.dtsi.
In the case we want to use transfer_one() API to communicate with a SPI
device, chip select signal must be driven individually.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Fix the Amarula Solutions typo mistake in license text added in below
commits.
commit <3ff0810ffc479> ("ARM: dts: stm32: Add Engicam i.Core STM32MP1
C.TOUCH 2.0 10.1" OF")
commit <6ca2898df59f7> ("ARM: dts: stm32: Add Engicam i.Core STM32MP1
C.TOUCH 2.0")
commit <adc0496104b64> ("ARM: dts: stm32: Add Engicam i.Core STM32MP1
EDIMM2.2 Starter Kit")
commit <30f9a9da4ee13> ("ARM: dts: stm32: Add Engicam i.Core STM32MP1
SoM")
commit <1d278204cbaa1> ("ARM: dts: stm32: Add Engicam MicroGEA STM32MP1
MicroDev 2.0 7" OF")
commit <f838dae7afd00> ("ARM: dts: stm32: Add Engicam MicroGEA STM32MP1
MicroDev 2.0 board")
commit <0be81dfaeaf89> ("ARM: dts: stm32: Add Engicam MicroGEA STM32MP1
SoM")
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
The timer units in the stm32mp15x CPUs have interrupts, depending on the
timer flavour either one "global" or four dedicated ones. Add the irqs
to the timer units on stm32mp15x.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Add pinctrl information and a disabled spi5 node within
stm32mp135f-dk.dts in order to use the spi5 bus which is
available via the GPIO expansion pins of the STM32MP135 Discovery board.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Add the 5 instances of spi busses supported by the stm32mp131.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
Arnd Bergmann
Linus Walleij
Bart Van Assche
Kees Cook
Geert Uytterhoeven
Tim Harvey
Sergiu Moga
Luca Weiss
Tao Ren
Jerry Ray
Horatiu Vultur
Christian Marangi
Krzysztof Kozlowski
Dmitry Baryshkov
Wolfram Sang
Patrice Chotard
Jagan Teki
Uwe Kleine-König
Alain Volmat