| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Samsung DTS ARM changes for v5.3
1. Fixes for minor warnings.
2. Enable ADC on Exynos5410 Odroid XU board.
* tag 'samsung-dt-5.3' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Add ADC node to Exynos5410 and Odroid XU
ARM: dts: exynos: Raise maximum buck regulator voltages on Arndale Octa
ARM: dts: exynos: Move CPU OPP tables out of SoC node on Exynos5420
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
ARMv7 Vexpress updates for v5.3
1. Couple of updates switching to use new/updated bindings for CoreSight
dynamic funnel components and NOR flash partition type
2. Disable NOR flash on Vexpress TC2 platform as it conflicts with CPU
power management. This follows what we have on ARMv8 Juno platform
and is required after recent commit that enabled CFI NOR FLASH in
multi_v7 defconfig
* tag 'vexpress-updates-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
ARM: dts: vexpress: set the right partition type for NOR flash
arm: dts: vexpress-v2p-ca15_a7: disable NOR flash node by default
ARM: dts: vexpress-v2p-ca15_a7: update coresight DT bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
ti-sysc dts changes for v5.3
We can now drop the custom dts property "ti,hwmods" for drivers that
have the ti-sysc interconnect target module configured in dts.
Let's start with a minimal changes to omap4 uart and mmc. We use
omap4 as the starting point as it has runtime PM implemented and all
the omap variants after that are based on it with similar clkctrl
clock for the modules. More devices will be updated later on as they
get tested.
Note that these changes are based on the related ti-sysc driver
changes.
* tag 'omap-for-v5.3/ti-sysc-dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (21 commits)
ARM: dts: Drop legacy custom hwmods property for omap4 mmc
ARM: dts: Drop legacy custom hwmods property for omap4 uart
bus: ti-sysc: Detect uarts also on omap34xx
bus: ti-sysc: Do rstctrl reset handling in two phases
bus: ti-sysc: Add support for disabling module without legacy mode
bus: ti-sysc: Set ENAWAKEUP if available
bus: ti-sysc: Handle swsup idle mode quirks
bus: ti-sysc: Handle clockactivity for enable and disable
bus: ti-sysc: Enable interconnect target module autoidle bit on enable
bus: ti-sysc: Allow QUIRK_LEGACY_IDLE even if legacy_mode is not set
bus: ti-sysc: Make OCP reset work for sysstatus and sysconfig reset bits
bus: ti-sysc: Support 16-bit writes too
bus: ti-sysc: Add support for missing clockdomain handling
ARM: dts: dra71x: Disable usb4_tm target module
ARM: dts: dra71x: Disable rtc target module
ARM: dts: dra76x: Disable usb4_tm target module
ARM: dts: dra76x: Disable rtc target module
ARM: dts: dra76x: Update MMC2_HS200_MANUAL1 iodelay values
ARM: dts: am57xx-idk: Remove support for voltage switching for SD card
bus: ti-sysc: Handle devices with no control registers
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
dts changes for omap variants for v5.3
This series of changes improves support for few boards:
- configure another lcd type for logicpd torpedo devkit
- a series of updates for am335x phytec boards
- configure mmc card detect pin for am335x-baltos
* tag 'omap-for-v5.3/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-baltos: add support for MMC1 CD pin
ARM: dts: am335x-baltos: Fix PHY mode for ethernet
ARM: dts: Add support for phyBOARD-REGOR-AM335x
ARM: dts: am335x-pcm-953: Remove eth phy delay
ARM: dts: am335x-pcm-953: Update user led names
ARM: dts: am335x-phycore-som: Enable gpmc node in dts files
ARM: dts: am335x-phycore-som: Add emmc node
ARM: dts: am335x phytec boards: Remove regulator node
ARM: dts: Add LCD type 28 support to LogicPD Torpedo DM3730 devkit
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
A lot more love for rk3288 in general and veyron specially with changes
all over the place.
* tag 'v5.3-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (21 commits)
ARM: dts: rockchip: Split GPIO keys for veyron into multiple devices
ARM: dts: rockchip: Add HDMI i2c unwedging for rk3288-veyron
ARM: dts: rockchip: Add unwedge pinctrl entries for dw_hdmi on rk3288
ARM: dts: rockchip: Switch to builtin HDMI DDC bus on rk3288-veyron
ARM: dts: rockchip: Add pin names for rk3288-veyron jaq, mickey, speedy
ARM: dts: rockchip: fix pwm-cells for rk3288's pwm3
ARM: dts: rockchip: Configure the GPU thermal zone for mickey
ARM: dts: rockchip: Use the GPU to cool CPU thermal zone of veyron mickey
ARM: dts: rockchip: remove GPU 500 MHz OPP on rk3288
ARM: dts: rockchip: Use GPU as cooling device for the GPU thermal zone of the rk3288
ARM: dts: rockchip: Add #cooling-cells entry for rk3288 GPU
ARM: dts: rockchip: Mark that the rk3288 timer might stop in suspend
ARM: dts: rockchip: Add pin names for rk3288-veyron-jerry
ARM: dts: rockchip: Add pin names for rk3288-veyron-minnie
ARM: dts: raise GPU trip point temperature for speedy to 80 degC
ARM: dts: rockchip: raise GPU trip point temperatures for veyron
ARM: dts: rockchip: raise CPU trip point temperature for veyron to 100 degC
ARM: dts: rockchip: Make rk3288-veyron-minnie run at hs200
ARM: dts: rockchip: Make rk3288-veyron-mickey's emmc work again
ARM: dts: rockchip: Remove bogus 'i2s_clk_out' from rk3288-veyron-mickey
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
DTS updates for the Integrator, target kernel v5.3.
* tag 'integrator-dts-v5.3-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: dts: vexpress: specify AFS partition
ARM: dts: realview: specify AFS partition
ARM: dts: versatile: specify AFS partition
ARM: dts: integrator: specify AFS partition
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
It's a simple typo in the DNS file, which was pretty serious.
No scripts were working properly. Fix it up.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Leaving this NAS with display and backlight on heats it up
and dissipates power. Turn off the screen after 4 minutes,
it comes back on when a user touches the keys.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
We want to be able to wake from USB if a device is plugged in that
wants remote wakeup. Enable it on both dwc2 controllers.
NOTE: this is added specifically to veyron and not to rk3288 in
general since it's not known whether all rk3288 boards are designed to
support USB wakeup. It is plausible that some boards could shut down
important rails in S3.
Also note that currently wakeup doesn't seem to happen unless you use
the "deep" suspend mode (where SDRAM is turned off). Presumably the
shallow suspend mode is gating some sort of clock that's important but
I couldn't easily figure out how to get it working.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Neither pinctrl_i2c1_gpio nor pinctrl_i2c2_gpio are used anywhere in
the file, drop them.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
RPU2 uses UART2 as a serial console and UART1 is not used at all. Fix
incorrrectly specified 'stdout-path' to reflect that.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add devicetree support for 96Boards Meerkat96 board from Novtech. This
board is one of the Consumer Edition boards of the 96Boards family based
on i.MX7D SoC. Following are the currently supported features of the
board:
* uSD
* WiFi/BT
* USB
More information about this board can be found in 96Boards product page:
https://www.96boards.org/product/imx7-96/
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add PXP node for i.MX6UL/L SoC.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The SNVS poweroff depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up to external PMIC.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The SNVS power key depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The SNVS power key depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The SNVS power key depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The SNVS power key depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The SNVS power key depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable hdmi bridge sii9022 & display controller.
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
|
|
Fixes for omap variants
Three fixes mostly for dra7 SoC variants that have some devices disabled
compared to the base SoC. These got broken by the change of making devices
probe with ti-sysc interconnect target module and went unnnoticed for a
while. And there is no clkcel bit for timer12 unlike timer1. Also included
is a GPIO direction fix for phytec SDIO card detection.
* tag 'omap-for-v5.2/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x phytec boards: Fix cd-gpios active level
ARM: dts: dra72x: Disable usb4_tm target module
ARM: dts: Drop bogus CLKSEL for timer12 on dra7
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
5.2-rc1, please pull the following:
- Florian fixes the remaining Broadcom DTS files to have a valid
device_type = "memory" property which was missed during the removal of
skeleton.dtsi
* tag 'arm-soc/for-5.2/devicetree-fixes' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm: Add missing device_type = "memory" property
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Fixes for omap variants for dra7 mmc voltage and boot issues
This series contains dra7 mmc voltage fixes, and fixes to the recent
changes to probe devices with device tree data insteas of legacy
platform data:
- Two fixes for dra7 mmc that needs 1.8V mode disabled as in case of a
reset, the bootrom will try to access the mmc card at 3.3V potentially
damaging the card
- Two regression fixes for am335x d_can. We must allow devices with no
control registers for ti-sysc interconnect target module driver for
at least d_can, and we remove the incorrect control registers for
d_can. And we must configure the osc clock for d_can as otherwise
register access may fail depending on the bootloader version
- Four regression fixes for dra7 variant dts files to tag rtc and usb4
as disabled for dra71x and dra76x. These SoC variants do not have
these devices, and got accidentally enabled when the L4 interconnect
got defined in the dra7-l4.dtsi for the dra7 SoC family
* tag 'omap-for-v5.2/fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: dra71x: Disable usb4_tm target module
ARM: dts: dra71x: Disable rtc target module
ARM: dts: dra76x: Disable usb4_tm target module
ARM: dts: dra76x: Disable rtc target module
ARM: dts: dra76x: Update MMC2_HS200_MANUAL1 iodelay values
ARM: dts: am57xx-idk: Remove support for voltage switching for SD card
bus: ti-sysc: Handle devices with no control registers
ARM: dts: Configure osc clock for d_can on am335x
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add initial support for the display found on the LG Nexus 5 (hammerhead)
phone. This is based on work from Jonathan Marek.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Add the MDP5, DSI and DSI PHY blocks for the display found on the
msm8974 SoCs. This is based on work from msm8916.dtsi and Jonathan
Marek.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Add necessary device tree nodes for the main LCD backlight.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Add support for the Synaptics RMI4 touchscreen that is found on the
Nexus 5.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Enable cpufreq-dt support for da850-evm. The cvdd is supplied by the
tps65070 pmic with configurable output voltage. By default da850-evm
boards support frequencies up to 375MHz so enable this operating
point.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Add a fixed regulator for the da850-lcdk board along with board-specific
CPU configuration.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
Add a fixed regulator for the LEGO EV3 board along with board-specific
CPU configuration.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
This adds a cpu node and operating points to the common da850.dtsi file.
All operating points above 300MHz are disabled by default.
Regulators need to be hooked up on a per-board basis.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
This enables wake up on Bluetooth activity when the device is
suspended. The BT_HOST_WAKE signal is only connected on devices
with BT module that are connected through UART.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add crypto node in device tree for CAAM support.
Noteworthy is that on 7ulp the interrupt line is shared
between the two job rings.
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Signed-off-by: Franck LENORMAND <franck.lenormand@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Enable ECSPI2 and bind CPLD to both chip selects.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The LS1021A-TSN is a development board built by VVDN/Argonboards in
partnership with NXP.
It features the LS1021A SoC and the first-generation SJA1105T Ethernet
switch for prototyping implementations of a subset of IEEE 802.1 TSN
standards.
It has two regular Ethernet ports and four switched, TSN-capable ports.
It also features:
- One Arduino header
- One expansion header
- Two USB 3.0 ports
- One mini PCIe slot
- One SATA interface
- Accelerometer, gyroscope, temperature sensors
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Allows to use the SD interface at a higher speed mode if the card
supports it. For this the signaling voltage is switched from 3.3V to
1.8V under the usdhc1's drivers control.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
According to latest docs imx7d chips can go from 800 to 1200 mhz.
Maximum frequency is determined from two speed grading bits present in
OCOTP fuses at same location as other imx chips.
Also update to "typical" voltages from latest datasheet, 25mv higher
than current dts.
All imx7s parts are still fixed at 800mhz
Based on:
* IMX7DCEC Rev. 6, 03/2019
* IMX7SCEC Rev. 6, 03/2019
* IMX7DRM Rev. 1, 01/2018 Page 1102
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
|
|
This updates the WL1831 bluetooth to use the serial serdev driver
interface.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The i2c2 bus has a external plug which enables the easy connection of external
"bricks" with sensors of various kinds, while i2c4 on the Extended/Full boards
has a pair of on board motion sensors, accelerometer and magnetometer on one chip
and gyroscope on another so it makes sense to enable these i2c buses for use.
Tested on UDOO Neo Full.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Use the SPDX License Identifier for GPL-2.0+ OR X11
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
|
|
Baltos 5221/3220 devices provide CD signal on GPIO2_18.
Baltos 2110 device provides CD signal on GPIO1_15.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The PHY must add both tx and rx delay and not only on the tx clock.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Move the ADC from exynos5420.dtsi to a shared file between Exynos5410 and
Exynos542x: exynos54xx.dtsi. Enable the ADC on Odroid XU board.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Add the EMAC's OCP reset property on Arria10. The OCP reset bits are
also needed to correctly bring the EMACs out of reset correctly.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Add the two ltc2497 devices that are on the SoCFPGA Arria10
Socdk board at addresses 0x14 and 0x16.
Signed-off-by: Alan Tull <atull@kernel.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
Adding support for phyBOARD-REGOR-AM335x:
- CAN
- UART0 / UART2
- RS485
- USB device
- i2c RTC
- SD
- ethernet0 RMII
- ethernet1 MII
- Digital I/Os
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Default values fit better than these historical settings.
Hardware layout had been adapted accordingly already in
alpha stage. They did not cause problems for a long time.
Removed values now.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Rename user led nodes to match the phytec user leds name scheme.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
Olof Johansson
Linus Walleij
Douglas Anderson
Andrey Smirnov
Manivannan Sadhasivam
Sébastien Szymanski
Anson Huang
Yannick Fertré
Brian Masney
Jonathan Marek
Bartosz Golaszewski
David Lechner
Iuliana Prodan
Marek Vasut
Vladimir Oltean
Igor Opaniuk
Leonard Crestez
Tony Lindgren
Peter Robinson
Yegor Yefremov
Krzysztof Kozlowski
Dinh Nguyen
Alan Tull
Teresa Remmet