| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Now that the regulators are tied to the GPIO bank, we can remove the
unneeded regulator-always-on in reg_aldo2
Signed-off-by: Pablo Greco <pgreco@centosproject.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The AP6212 is based on the Broadcom BCM43430 or BCM43438. The WiFi side
identifies as BCM43430, while the Bluetooth side identifies as BCM43438.
The Bluetooth side is connected to UART3 in a 4 wire configuration. Same
as the WiFi side, due to being the same chip and package, DLDO1 and
DLDO2 regulator outputs from the PMIC provide overall power via VBAT and
I/O power via VDDIO. The CLK_OUT_A clock output from the SoC provides
the LPO low power clock at 32.768 kHz.
This patch enables Bluetooth on this board, and also adds the missing
LPO clock on the WiFi side. There is also a PCM connection for
Bluetooth, but this is not covered here.
The LPO clock is fed from CLK_OUT_A, which needs to be muxed on pin
PI12. This can be represented in multiple ways. This patch puts the
pinctrl property in the pin controller node. This is due to limitations
in Linux, where pinmux settings, even the same one, can not be shared
by multiple devices. Thus we cannot put it in both the WiFi and
Bluetooth device nodes. Putting it the CCU node is another option, but
Linux's CCU driver does not handle pinctrl. Also the pin controller is
guaranteed to be initialized after the CCU, when clocks are available.
And any other devices that use muxed pins are guaranteed to be
initialized after the pin controller. Thus having the CLK_OUT_A pinmux
reference be in the pin controller node is a good choice without having
to deal with implementation issues.
Signed-off-by: Pablo Greco <pgreco@centosproject.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Just like the Bananapi M2 Ultra, enable the ahci controller and
the two regulators needed to activate it.
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Pablo Greco <pgreco@centosproject.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
This patch adds the hdmi nodes to the Bananapi M2 Berry, the same way it
was done to the Bananapi M2 Ultra
Signed-off-by: Pablo Greco <pgreco@centosproject.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Just like the Bananapi M2 Ultra, the Bananapi M2 Berry has a Realtek
RTL8211E RGMII PHY tied to the GMAC.
The PMIC's DC1SW output provides power for the PHY, while the ALDO2
output provides I/O voltages on both sides.
Signed-off-by: Pablo Greco <pgreco@centosproject.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The bananapi-m2-berry has the PMIC providing voltage to all the pin-bank
supply rails from its various regulator outputs, tie them to the pio
node.
Signed-off-by: Pablo Greco <pgreco@centosproject.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The bananapi-m2-ultra has the PMIC providing voltage to all the pin-bank
supply rails from its various regulator outputs, tie them to the pio
node.
Signed-off-by: Pablo Greco <pgreco@centosproject.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
On i.MX6SX SDB board, vgen6 supplies vdd1p1/vdd2p5 LDO and
sw2 supplies vdd3p0 LDO, this patch assigns corresponding power
supply for vdd1p1/vdd2p5/vdd3p0 to avoid confusion by below log:
vdd1p1: supplied by regulator-dummy
vdd3p0: supplied by regulator-dummy
vdd2p5: supplied by regulator-dummy
With this patch, the power supply is more accurate:
vdd1p1: supplied by VGEN6
vdd3p0: supplied by SW2
vdd2p5: supplied by VGEN6
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
On i.MX6SLL EVK board, sw2 supplies vdd3p0 LDO, this patch assigns
corresponding power supply for vdd3p0 to avoid confusion by below log:
vdd3p0: supplied by regulator-dummy
With this patch, the power supply is more accurate:
vdd3p0: supplied by SW2
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
On i.MX6SL EVK board, sw2 supplies vdd1p1/vdd2p5/vdd3p0 LDO, this
patch assigns corresponding power supply for vdd1p1/vdd2p5/vdd3p0
to avoid confusion by below log:
vdd1p1: supplied by regulator-dummy
vdd3p0: supplied by regulator-dummy
vdd2p5: supplied by regulator-dummy
With this patch, the power supply is more accurate:
vdd1p1: supplied by SW2
vdd3p0: supplied by SW2
vdd2p5: supplied by SW2
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
On i.MX7D SDB board, sw2 supplies 1p0d/1p2 LDO, this patch assigns
corresponding power supply for 1p0d/1p2 LDO to avoid confusion by
below log:
vdd1p0d: supplied by regulator-dummy
vdd1p2: supplied by regulator-dummy
With this patch, the power supply is more accurate:
vdd1p0d: supplied by SW2
vdd1p2: supplied by SW2
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
On i.MX6Q/DL SabreSD board, vgen5 supplies vdd1p1/vdd2p5 LDO and
sw2 supplies vdd3p0 LDO, this patch assigns corresponding power
supply for vdd1p1/vdd2p5/vdd3p0 to avoid confusion by below log:
vdd1p1: supplied by regulator-dummy
vdd3p0: supplied by regulator-dummy
vdd2p5: supplied by regulator-dummy
With this patch, the power supply is more accurate:
vdd1p1: supplied by VGEN5
vdd3p0: supplied by SW2
vdd2p5: supplied by VGEN5
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add clock-frequency property to CPU node. Avoids warnings like
"/cpus/cpu@0 missing clock-frequency property" for "arm,cortex-a7".
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This patch adds i.MX7ULP EVK board MIPI-DSI backlight support.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add i.MX7ULP EVK board PWM support.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
CoreSight DT bindings have been updated, thus the old compatible strings
are obsolete and the drivers will report warning if DTS uses these
obsolete strings.
This patch switches to the new bindings for CoreSight dynamic funnel and
static replicator, so can dismiss warning during initialisation.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Update pinmux settings according to hardware team input.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add meaningful GPIO line names for the board GPIOs.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add GPIO beeper, to let the board produce beeps.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add GPIO power button and GPIO poweroff, which is present on new hardware.
These let the system power itself off on shutdown.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The yellow LED is in the ethernet jack socket, bind it to netdev
trigger to indicate ethernet activity.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add ethernet PHY GPIO reset line, to let the kernel to reset the PHY.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Turn USBH1 into Host and update the GPIO polarity of the
regulator to match new hardware.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable flow control lines on UART1 and UART2, add matching pinmux entries.
Add and enable UART3 with RS485 mode enabled on boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
i.MX6Q/DL's WDOGs use IMX6QDL_CLK_IPG as clock root, assign
IMX6QDL_CLK_IPG to them instead of IMX6QDL_CLK_DUMMY.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
i.MX6SL's KPP and WDOG use IMX6SL_CLK_IPG as clock root,
assign IMX6SL_CLK_IPG to them instead of IMX6SL_CLK_DUMMY.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Raise the temperature of the GPU thermal trip point for speedy
to 80°C. This is the value used by the downstream Chrome OS 3.14
kernel, the 'official' kernel for speedy.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The values match those used by the downstream Chrome OS 3.14
kernel, the 'official' kernel for veyron devices. Keep the critical
trip point for speedy at 90°C as in the downstream configuration.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This value matches what is used by the downstream Chrome OS 3.14
kernel, the 'official' kernel for veyron devices. Keep the temperature
for 'speedy' at 90°C, as in the downstream kernel.
Increase the temperature for a hardware shutdown to 125°C, which
matches the downstream configuration and gives the system a chance
to shut down orderly at the criticial trip point.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
As some point hs200 was failing on rk3288-veyron-minnie. See commit
984926781122 ("ARM: dts: rockchip: temporarily remove emmc hs200 speed
from rk3288 minnie"). Although I didn't track down exactly when it
started working, it seems to work OK now, so let's turn it back on.
To test this, I booted from SD card and then used this script to
stress the enumeration process after fixing a memory leak [1]:
cd /sys/bus/platform/drivers/dwmmc_rockchip
for i in $(seq 1 3000); do
echo "========================" $i
echo ff0f0000.dwmmc > unbind
sleep .5
echo ff0f0000.dwmmc > bind
while true; do
if [ -e /dev/mmcblk2 ]; then
break;
fi
sleep .1
done
done
It worked fine.
[1] https://lkml.kernel.org/r/20190503233526.226272-1-dianders@chromium.org
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
When I try to boot rk3288-veyron-mickey I totally fail to make the
eMMC work. Specifically my logs (on Chrome OS 4.19):
mmc_host mmc1: card is non-removable.
mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0)
mmc1: switch to bus width 8 failed
mmc1: switch to bus width 4 failed
mmc1: new high speed MMC card at address 0001
mmcblk1: mmc1:0001 HAG2e 14.7 GiB
mmcblk1boot0: mmc1:0001 HAG2e partition 1 4.00 MiB
mmcblk1boot1: mmc1:0001 HAG2e partition 2 4.00 MiB
mmcblk1rpmb: mmc1:0001 HAG2e partition 3 4.00 MiB, chardev (243:0)
mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0)
mmc1: switch to bus width 8 failed
mmc1: switch to bus width 4 failed
mmc1: tried to HW reset card, got error -110
mmcblk1: error -110 requesting status
mmcblk1: recovery failed!
print_req_error: I/O error, dev mmcblk1, sector 0
...
When I remove the '/delete-property/mmc-hs200-1_8v' then everything is
hunky dory.
That line comes from the original submission of the mickey dts
upstream, so presumably at the time the HS200 was failing and just
enumerating things as a high speed device was fine. ...or maybe it's
just that some mickey devices work when enumerating at "high speed",
just not mine?
In any case, hs200 seems good now. Let's turn it on.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The rk3288-veyron-mickey device tree overrides the default "i2s" clock
settings to add the clock for "i2s_clk_out".
That clock is only present in the bindings downstream Chrome OS 3.14
tree. Upstream the i2s port bindings doesn't specify that as a
possible clock.
Let's remove it.
NOTE: for other rk3288-veyron devices this clock is consumed by
'maxim,max98090'. Presumably if this clock is needed for mickey it'll
need to be consumed by something similar.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
We use the new PWM IP on RK3288, but the PWM's clock indeed incorrect.
Signed-off-by: Caesar Wang <caesar.wang@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Two regression fixes for omaps
Two one-liners to fix board-ams-delta booting regression and
logicpd-som-lv MMC card detect to use GPIO_ACTIVE_LOW instead of
IRQ_TYPE_LEVEL_LOW. Note that the board-ams-delta regression has
been in there already since v5.0, so if necessary these can wait
for the merge window.
* tag 'omap-for-v5.1/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: logicpd-som-lv: Fix MMC1 card detect
ARM: OMAP1: ams-delta: fix early boot crash when LED support is disabled
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Pull ARM Device-tree updates from Olof Johansson:
"Besides new bindings and additional descriptions of hardware blocks
for various SoCs and boards, the main new contents here is:
SoCs:
- Intel Agilex (SoCFPGA)
- NXP i.MX8MM (Quad Cortex-A53 with media/graphics focus)
New boards:
- Allwinner:
+ RerVision H3-DVK (H3)
+ Oceanic 5205 5inMFD (H6)
+ Beelink GS2 (H6)
+ Orange Pi 3 (H6)
- Rockchip:
+ Orange Pi RK3399
+ Nanopi NEO4
+ Veyron-Mighty Chromebook variant
- Amlogic:
+ SEI Robotics SEI510
- ST Micro:
+ stm32mp157a discovery1
+ stm32mp157c discovery2
- NXP:
+ Eckelmann ci4x10 (i.MX6DL)
+ i.MX8MM EVK (i.MX8MM)
+ ZII i.MX7 RPU2 (i.MX7)
+ ZII SPB4 (VF610)
+ Zii Ultra (i.MX8M)
+ TQ TQMa7S (i.MX7Solo)
+ TQ TQMa7D (i.MX7Dual)
+ Kobo Aura (i.MX50)
+ Menlosystems M53 (i.MX53)j
- Nvidia:
+ Jetson Nano (Tegra T210)"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (593 commits)
arm64: dts: bitmain: Add UART pinctrl support for Sophon Edge
arm64: dts: bitmain: Add pinctrl support for BM1880 SoC
arm64: dts: bitmain: Add GPIO Line names for Sophon Edge board
arm64: dts: bitmain: Add GPIO support for BM1880 SoC
ARM: dts: gemini: Indent DIR-685 partition table
dt-bindings: hwmon (pwm-fan) Remove dead "cooling-*-state" properties
ARM: dts: qcom-apq8064: Set 'cxo_board' as ref clock of the DSI PHY
arm64: dts: msm8998: thermal: Restrict thermal zone name length to under 20
arm64: dts: msm8998: thermal: Fix number of supported sensors
arm64: dts: msm8998-mtp: thermal: Remove skin and battery thermal zones
arm64: dts: exynos: Move fixed-clocks out of soc
arm64: dts: exynos: Move pmu and timer nodes out of soc
ARM: dts: s5pv210: Fix camera clock provider on Goni board
ARM: dts: exynos: Properly override node to use MDMA0 on Universal C210
ARM: dts: exynos: Move fixed-clocks out of soc on Exynos3250
ARM: dts: exynos: Remove unneeded address/size cells from fixed-clock on Exynos3250
ARM: dts: exynos: Move pmu and timer nodes out of soc
arm64: dts: rockchip: fix IO domain voltage setting of APIO5 on rockpro64
arm64: dts: db820c: Add sound card support
arm64: dts: apq8096-db820c: Add HDMI display support
...
|
|
Pull ARM SoC platform updates from Olof Johansson:
"SoC updates, mostly refactorings and cleanups of old legacy platforms.
Major themes this release:
- Conversion of ixp4xx to a modern platform (drivers, DT, bindings)
- Moving some of the ep93xx headers around to get it closer to
multiplatform enabled.
- Cleanups of Davinci
This also contains a few patches that were queued up as fixes before
5.1 but I didn't get sent in before release"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (123 commits)
ARM: debug-ll: add default address for digicolor
ARM: u300: regulator: add MODULE_LICENSE()
ARM: ep93xx: move private headers out of mach/*
ARM: ep93xx: move pinctrl interfaces into include/linux/soc
ARM: ep93xx: keypad: stop using mach/platform.h
ARM: ep93xx: move network platform data to separate header
ARM: stm32: add AMBA support for stm32 family
MAINTAINERS: update arch/arm/mach-davinci
ARM: rockchip: add missing of_node_put in rockchip_smp_prepare_pmu
ARM: dts: Add queue manager and NPE to the IXP4xx DTSI
soc: ixp4xx: qmgr: Add DT probe code
soc: ixp4xx: qmgr: Add DT bindings for IXP4xx qmgr
soc: ixp4xx: npe: Add DT probe code
soc: ixp4xx: Add DT bindings for IXP4xx NPE
soc: ixp4xx: qmgr: Pass resources
soc: ixp4xx: Remove unused functions
soc: ixp4xx: Uninline several functions
soc: ixp4xx: npe: Pass addresses as resources
ARM: ixp4xx: Turn the QMGR into a platform device
ARM: ixp4xx: Turn the NPE into a platform device
...
|
|
Merge in a few pending fixes from pre-5.1 that didn't get sent in:
MAINTAINERS: update arch/arm/mach-davinci
ARM: dts: ls1021: Fix SGMII PCS link remaining down after PHY disconnect
ARM: dts: imx6q-logicpd: Reduce inrush current on USBH1
ARM: dts: imx6q-logicpd: Reduce inrush current on start
ARM: dts: imx: Fix the AR803X phy-mode
ARM: dts: sun8i: a33: Reintroduce default pinctrl muxing
arm64: dts: allwinner: a64: Rename hpvcc-supply to cpvdd-supply
ARM: sunxi: fix a leaked reference by adding missing of_node_put
ARM: sunxi: fix a leaked reference by adding missing of_node_put
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Pull USB/PHY updates from Greg KH:
"Here is the big set of USB and PHY driver patches for 5.2-rc1
There is the usual set of:
- USB gadget updates
- PHY driver updates and additions
- USB serial driver updates and fixes
- typec updates and new chips supported
- mtu3 driver updates
- xhci driver updates
- other tiny driver updates
Nothing really interesting, just constant forward progress.
All of these have been in linux-next for a while with no reported
issues. The usb-gadget and usb-serial trees were merged a bit "late",
but both of them had been in linux-next before they got merged here
last Friday"
* tag 'usb-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (206 commits)
USB: serial: f81232: implement break control
USB: serial: f81232: add high baud rate support
USB: serial: f81232: clear overrun flag
USB: serial: f81232: fix interrupt worker not stop
usb: dwc3: Rename DWC3_DCTL_LPM_ERRATA
usb: dwc3: Fix default lpm_nyet_threshold value
usb: dwc3: debug: Print GET_STATUS(device) tracepoint
usb: dwc3: Do core validation early on probe
usb: dwc3: gadget: Set lpm_capable
usb: gadget: atmel: tie wake lock to running clock
usb: gadget: atmel: support USB suspend
usb: gadget: atmel_usba_udc: simplify setting of interrupt-enabled mask
dwc2: gadget: Fix completed transfer size calculation in DDMA
usb: dwc2: Set lpm mode parameters depend on HW configuration
usb: dwc2: Fix channel disable flow
usb: dwc2: Set actual frame number for completed ISOC transfer
usb: gadget: do not use __constant_cpu_to_le16
usb: dwc2: gadget: Increase descriptors count for ISOC's
usb: introduce usb_ep_type_string() function
usb: dwc3: move synchronize_irq() out of the spinlock protected block
...
|
|
Pull LED updates from Jacek Anaszewski:
"LED core fixes and improvements:
- avoid races with workqueue
- Kconfig: pedantic cleanup
- small fixes for Flash class description
leds-lt3593:
- remove unneeded assignment in lt3593_led_probe
- drop pdata handling code
leds-blinkm:
- clean up double assignment to data->i2c_addr
leds-pca955x, leds-pca963x:
- revert ACPI support, as it turned out that there is no evidence
of officially registered ACPI IDs for these devices.
- make use of device property API
leds-as3645a:
- switch to fwnode property API
LED related addition to ACPI documentation:
- document how to refer to LEDs from remote nodes
LED related fix to ALSA line6/toneport driver:
- avoid polluting led_* namespace
And lm3532 driver relocation from MFD to LED subsystem, accompanied by
various improvements and optimizations; it entails also a change in
omap4-droid4-xt894.dts:
- leds: lm3532: Introduce the lm3532 LED driver
- mfd: ti-lmu: Remove LM3532 backlight driver references
- ARM: dts: omap4-droid4: Update backlight dt properties
- dt: lm3532: Add lm3532 dt doc and update ti_lmu doc"
* tag 'leds-for-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: avoid races with workqueue
ALSA: line6: Avoid polluting led_* namespace
leds: lm3532: Introduce the lm3532 LED driver
mfd: ti-lmu: Remove LM3532 backlight driver references
ARM: dts: omap4-droid4: Update backlight dt properties
dt: lm3532: Add lm3532 dt doc and update ti_lmu doc
leds: Small fixes for Flash class description
leds: blinkm: clean up double assignment to data->i2c_addr
leds: pca963x: Make use of device property API
leds: pca955x: Make use of device property API
leds: lt3593: Remove unneeded assignment in lt3593_led_probe
leds: lt3593: drop pdata handling code
leds: pca955x: Revert "Add ACPI support"
leds: pca963x: Revert "Add ACPI support"
drivers: leds: Kconfig: pedantic cleanups
ACPI: Document how to refer to LEDs from remote nodes
leds: as3645a: Switch to fwnode property API
|
|
Pull staging / IIO driver updates from Greg KH:
"Here is the big staging and iio driver update for 5.2-rc1.
Lots of tiny fixes all over the staging and IIO driver trees here,
along with some new IIO drivers.
The "counter" subsystem was added in here as well, as it is needed by
the IIO drivers and subsystem.
Also we ended up deleting two drivers, making this pull request remove
a few hundred thousand lines of code, always a nice thing to see. Both
of the drivers removed have been replaced with "real" drivers in their
various subsystem directories, and they will be coming to you from
those locations during this merge window.
There are some core vt/selection changes in here, that was due to some
cleanups needed for the speakup fixes. Those have all been acked by
the various subsystem maintainers (i.e. me), so those are ok.
We also added a few new drivers, for some odd hardware, giving new
developers plenty to work on with basic coding style cleanups to come
in the near future.
Other than that, nothing unusual here.
All of these have been in linux-next for a while with no reported
issues, other than an odd gcc warning for one of the new drivers that
should be fixed up soon"
[ I fixed up the warning myself - Linus ]
* tag 'staging-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (663 commits)
staging: kpc2000: kpc_spi: Fix build error for {read,write}q
Staging: rtl8192e: Remove extra space before break statement
Staging: rtl8192u: ieee80211: Fix if-else indentation warning
Staging: rtl8192u: ieee80211: Fix indentation errors by removing extra spaces
staging: most: cdev: fix chrdev_region leak in mod_exit
staging: wlan-ng: Fix improper SPDX comment style
staging: rtl8192u: ieee80211: Resolve ERROR reported by checkpatch
staging: vc04_services: bcm2835-camera: Compress two lines into one line
staging: rtl8723bs: core: Use !x in place of NULL comparison.
staging: rtl8723bs: core: Prefer using the BIT Macro.
staging: fieldbus: anybus-s: fix wait_for_completion_timeout return handling
staging: kpc2000: fix up build problems with readq()
staging: rtlwifi: move remaining phydm .h files
staging: rtlwifi: strip down phydm .h files
staging: rtlwifi: delete the staging driver
staging: fieldbus: anybus-s: rename bus id field to avoid confusion
staging: fieldbus: anybus-s: keep device bus id in bus endianness
Staging: sm750fb: Change *array into *const array
staging: rtl8192u: ieee80211: Fix spelling mistake
staging: rtl8192u: ieee80211: Replace bit shifting with BIT macro
...
|
|
Felipe writes:
USB: changes for v5.2 merge window
With a total of 50 non-merge commits, this is not a large pull
request. Most of the changes are, again, in dwc2 (37%) and dwc3 (32%)
with the rest of it scattered among other UDCs, function drivers and
device-tree bindings.
No really big feature this time around apart from support to Amlogic
being added to both dwc3 and dwc2 drivers.
* tag 'usb-for-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (50 commits)
usb: dwc3: Rename DWC3_DCTL_LPM_ERRATA
usb: dwc3: Fix default lpm_nyet_threshold value
usb: dwc3: debug: Print GET_STATUS(device) tracepoint
usb: dwc3: Do core validation early on probe
usb: dwc3: gadget: Set lpm_capable
usb: gadget: atmel: tie wake lock to running clock
usb: gadget: atmel: support USB suspend
usb: gadget: atmel_usba_udc: simplify setting of interrupt-enabled mask
dwc2: gadget: Fix completed transfer size calculation in DDMA
usb: dwc2: Set lpm mode parameters depend on HW configuration
usb: dwc2: Fix channel disable flow
usb: dwc2: Set actual frame number for completed ISOC transfer
usb: gadget: do not use __constant_cpu_to_le16
usb: dwc2: gadget: Increase descriptors count for ISOC's
usb: introduce usb_ep_type_string() function
usb: dwc3: move synchronize_irq() out of the spinlock protected block
usb: dwc3: Free resource immediately after use
usb: dwc3: of-simple: Convert to bulk clk API
usb: dwc2: Delayed status support
usb: gadget: udc: lpc32xx: rework interrupt handling
...
|
|
The "host" USB port on rk3288 has a hardware errata where we've got to
assert a PHY reset whenever we see a remote wakeup. Add that quirk
property to the device tree.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Let's hook up the resets to the three USB PHYs on rk3288 as per the
bindings. This is in preparation for a future patch that will set the
"snps,reset-phy-on-wake" on the host port.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
|
|
Update the MMC2_HS200_MANUAL1 iodelay values to match with the latest
dra76x data manual[1]. The new iodelay values will have better marginality
and should prevent issues in corner cases.
Also this particular pinctrl-array is using spaces instead of tabs for
spacing between the values and the comments. Fix this as well.
[1] http://www.ti.com/lit/ds/symlink/dra76p.pdf
Cc: <stable@vger.kernel.org>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
[tony@atomide.com: updated description with a bit more info]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
If UHS speed modes are enabled, a compatible SD card switches down to
1.8V during enumeration. If after this a software reboot/crash takes
place and on-chip ROM tries to enumerate the SD card, the difference in
IO voltages (host @ 3.3V and card @ 1.8V) may end up damaging the card.
The fix for this is to have support for power cycling the card in
hardware (with a PORz/soft-reset line causing a power cycle of the
card). Since am571x-, am572x- and am574x-idk don't have this
capability, disable voltage switching for these boards.
The major effect of this is that the maximum supported speed
mode is now high speed(50 MHz) down from SDR104(200 MHz).
Cc: <stable@vger.kernel.org>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Some interconnect target modules have no module control registers at
all, such as d_can on am335x and am437x.
The d_can register offset at 0 is CTL register with 0x401 as the default
value. I guess I mistook the 0x401 value for a revision register as the
value happens to look similar to what the revision registers typically
have for other modules.
To handle modules with no control registers, we need to improve the
ti-sysc driver a bit to bail out with errors on no control registers,
and then we can remove the bogus revision registers for d_can.
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Reading the module revision register can cause an external abort on
non-linefetch depending of osc clock is not already enabled. This
started happening with commit 1a5cd7c23cc5 ("bus: ti-sysc: Enable all
clocks directly during init to read revision") as reported by
Sebastian Andrzej Siewior <bigeasy@linutronix.de>.
The reason why the issue happens is because we now attempt to read the
interconnect target module revision register by first manually enabling
all the device clocks in sysc_probe(). And looks like d_can also needs
the osc clock in addition to the module clock, and it may or may not be
enabled depending on the bootloader version and if other devices have
already requested osc clock.
Let's fix the issue by adding osc clock as an optional clock for the
module for am335x. Note that am437x does not seem to list the osc clock
at all, so presumably it is not needed for am437x.
I also noticed that we're incorrectly assuming the revision register for
d_can exists. But the module does not seem to have any revision, sysconfig
or sysstatus registers. But that's mostly a cosmetic issues, so I'll send
a patch separately for that.
Fixes: 1a5cd7c23cc5 ("bus: ti-sysc: Enable all clocks directly during init to read revision")
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The card detect pin was incorrectly using IRQ_TYPE_LEVEL_LOW
instead of GPIO_ACTIVE_LOW when reading the state of the CD pin.
This was previosly fixed on Torpedo, but missed on the SOM-LV
Fixes: 5cb8b0fa55a9 ("ARM: dts: Move most of logicpd-som-lv-37xx-devkit.dts to logicpd-som-lv-baseboard.dtsi")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
ARM: lpc32xx: devicetree updates for v5.2
Here are the changes for ARM NXP LPC32xx devicetree files:
* disabled I2S and MAC controllers by default,
* set default #address-cells = <1> / #size-cells = <0> for SPI slaves,
* fix notation of hexadecimal values,
* switched lpc32xx.dtsi to SPDX license identifier.
* tag 'lpc32xx-dt-for-5.2' of https://github.com/vzapolskiy/linux-lpc32xx:
ARM: dts: lpc32xx: use SPDX license identifier
ARM: dts: lpc32xx: add address and size cell values to SPI controller nodes
ARM: dts: lpc32xx: disable MAC controller by default
ARM: dts: lpc32xx: disable I2S controllers by default
ARM: dts: lpc32xx: change hexadecimal values to lower case
Signed-off-by: Olof Johansson <olof@lixom.net>
|
Pablo Greco
Anson Huang
Leo Yan
Marek Vasut
Matthias Kaehlcke
Douglas Anderson
Caesar Wang
Olof Johansson
Linus Torvalds
Greg Kroah-Hartman
Tony Lindgren
Faiz Abbas
Adam Ford