aboutsummaryrefslogtreecommitdiffstats
path: root/arch/arm/boot
AgeCommit message (Collapse)AuthorFilesLines
2022-05-07ARM: dts: imx6ull-colibri: update device trees to support overlaysDenys Drozdov2-33/+27
Prepare in-tree device trees for out-of-tree device tree overlay support (eMMC SKU only). Relocate panel-dpi default to edt,et057090dhu (RGB 18bit VGA 640x480) to the module-level dtsi and remove it from the carrier board dtsi. Keep backlight, resistive touch and Atmel maxtouch nodes enabled for both eMMC and NAND modules. Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2022-05-07ARM: dts: imx6ull-colibri: update usdhc1 pixmux and signalingPhilippe Schenker2-26/+24
Due to many carrier boards pulling the usdhc1 signals up to 3.3 volt we need to disable 1.8 volt signaling. Adding the no-1-8-v property basically disables UHS-I modes by default. Also pull-up the command and data lines to the +V3.3_1.8_SD rail and set them to the 200 MHz speed grade (e.g. pinmux bits 7-6: meaning 11 SPEED_3_max_200MHz). Explicitly specify a bus-width of <4> in the module-level device tree include file and drop the no-1-8-v property from the carrier boards device trees. Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com> Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2022-05-07ARM: dts: imx6ull-colibri: add touchscreen device nodesDenys Drozdov3-16/+31
Move all Atmel nodes from the board-level into the main module-level device tree and prepare the device trees for use with Atmel MXT device tree overlays. Also, add required pinmux groups. The common scheme for pin groups in touch screen overlays is as follows: - pinctrl_atmel_conn - SODIMM 106/107 pins for INT/RST signals (default) - pinctrl_atmel_adap - SODIMM 28/30 pins for INT/RST signals. Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2022-05-07ARM: dts: imx6ull-colibri: add phy-supply to fecPhilippe Schenker1-0/+13
This adds the proper phy-supply to the FEC. This supply is actually switched by a clock that is now properly stated. This has the advantage to add a delay for that particular regulator which is needed. Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2022-05-07ARM: dts: imx6ull-colibri: change touch i2c parametersMax Krummenacher1-4/+6
Switch on 22 kOhm pull-ups and lower the I2C frequency to around 40 kHz to get more reliable communication. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2022-05-07ARM: dts: imx6ull-colibri: use pull-down for adc pinsPhilippe Schenker1-0/+12
Disable the keeper and enable a 100k pull-down on the ADC pins as per the following note in section 13.2 of the i.MX 6ULL Application Processor Reference Manual, Rev. 1, 11/2017 [1]: The keeper causes an undesired jump behavior in ADC. To avoid the problem, disable keeper before starting ADC. [1] https://www.nxp.com/webapp/Download?colCode=IMX6ULLRM Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2022-05-06Merge tag 'sunxi-dt-for-5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dtArnd Bergmann2-10/+125
- F1C100 improvements (SPI, MMC, timer, cpu, watchdog) - SPI flash node for licheepi-nano - enabled analogue audio on olinuxino-a64 - GPIO port regulators on teres-i * tag 'sunxi-dt-for-5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: arm64: dts: allwinner: teres-i: Add GPIO port regulators arm64: dts: allwinner: a64: olinuxino: Enable audio ARM: dts: suniv: licheepi-nano: add SPI flash ARM: dts: suniv: F1C100: add SPI support dt-bindings: spi: sunxi: document F1C100 controllers ARM: dts: suniv: licheepi-nano: add microSD card ARM: dts: suniv: F1C100: add MMC controllers ARM: dts: suniv: F1C100: fix timer node ARM: dts: suniv: F1C100: fix CPU node ARM: dts: suniv: F1C100: add clock and reset macros dt-bindings: arm: sunxi: document LicheePi Nano name ARM: dts: suniv: F1C100: fix watchdog compatible dt-bindings: watchdog: sunxi: clarify clock support dt-bindings: watchdog: sunxi: fix F1C100s compatible Link: https://lore.kernel.org/r/YnVUmSLE1MZFkApt@kista.localdomain Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-05-06Merge tag 'renesas-arm-dt-for-v5.19-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dtArnd Bergmann1-0/+110
Renesas ARM DT updates for v5.19 (take two) - I2C, sound, USB, CANFD, timer, watchdog, (Q)SPI, cpufreq, and thermal support for the RZ/G2UL SoC and the RZ/G2UL SMARC EVK development board, - Initial support for the R-Car V4H SoC and the Renesas White Hawk development board stack, - DMA, RTC, and USB support for the RZ/N1D SoC, - Initial support for the RZ/V2M SoC an the RZ/V2M Evaluation Kit Board, - Miscellaneous fixes and improvements. * tag 'renesas-arm-dt-for-v5.19-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: (40 commits) arm64: dts: renesas: Add initial device tree for RZ/V2M EVK arm64: dts: renesas: Add initial DTSI for RZ/V2M SoC arm64: dts: renesas: r8a779a0: Update to R-Car Gen4 compatible values ARM: dts: r9a06g032: Link the PCI USB devices to the USB PHY ARM: dts: r9a06g032: Add USB PHY DT support ARM: dts: r9a06g032: Add internal PCI bridge node ARM: dts: r9a06g032: Describe the RTC arm64: dts: renesas: Add interrupt-names to CANFD nodes arm64: dts: renesas: r9a07g043: Add SPI Multi I/O Bus controller node arm64: dts: renesas: r9a07g043: Create thermal zone to support IPA arm64: dts: renesas: r9a07g043: Add TSU node arm64: dts: renesas: r9a07g043: Add OPP table arm64: dts: renesas: r9a07g043: Add RSPI{0,1,2} nodes arm64: dts: renesas: r9a07g054: Fix external clk node names arm64: dts: renesas: r9a07g044: Fix external clk node names ARM: dts: r9a06g032: Fix the NAND controller node ARM: dts: r9a06g032: Fill the UART DMA properties ARM: dts: r9a06g032: Describe the DMA router ARM: dts: r9a06g032: Add the two DMA nodes arm64: dts: renesas: Remove empty rgb output endpoints ... Link: https://lore.kernel.org/r/cover.1651828603.git.geert+renesas@glider.be Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-05-06Merge tag 'samsung-dt-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dtArnd Bergmann8-42/+2
Samsung DTS ARM changes for v5.19, part two 1. Cleanups: unused and undocumented dma-channels and dma-requests. 2. Correct compatible of Samsung EEPROM on S5PV210. * tag 'samsung-dt-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: ARM: dts: exynos: drop useless 'dma-channels/requests' properties ARM: dts: s5pv210: drop useless 'dma-channels/requests' properties ARM: dts: exynos: add atmel,24c128 fallback to Samsung EEPROM Link: https://lore.kernel.org/r/20220506081438.149192-4-krzysztof.kozlowski@linaro.org Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-05-06Merge tag 'dt-cleanup-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dtArnd Bergmann59-71/+65
Minor cleanup of ARM DTS for v5.19, part two Align SPI NOR node names to DT schema and drop unused/undocumented dma-channels/dma-requests. * tag 'dt-cleanup-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: ARM: dts: socfpga: drop useless 'dma-channels/requests' properties ARM: dts: zynq-7000: drop useless 'dma-channels/requests' properties ARM: dts: marvell: align SPI NOR node name with dtschema ARM: dts: omap: align SPI NOR node name with dtschema ARM: dts: nuvoton: align SPI NOR node name with dtschema Link: https://lore.kernel.org/r/20220506081438.149192-2-krzysztof.kozlowski@linaro.org Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-05-06ARM: dts: Add bosch acc boardPhilip Oberfichtner2-0/+780
Add device tree for the Bosch ACC board, based on i.MX6 Dual. Signed-off-by: Philip Oberfichtner <pro@denx.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2022-05-06ARM: dts: imx: Add i.MXRT1050-EVK supportGiulio Benetti3-0/+234
The NXP i.MXRT1050 Evaluation Kit (EVK) provides a platform for rapid evaluation of the i.MXRT, which features NXP's implementation of the Arm Cortex-M7 core. The EVK provides 32 MB SDRAM, 64 MB Quad SPI flash, Micro SD card socket, USB 2.0 OTG. This patch aims to support the preliminary booting up features as follows: GPIO LPUART SD/MMC Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com> [Jesse: Add clock-parents, edma, usdhc, anatop, remove old pinctl] Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2022-05-06ARM: dts: r9a06g032: Link the PCI USB devices to the USB PHYHerve Codina1-0/+12
Describe the PCI USB devices that are behind the PCI bridge, adding necessary links to the USB PHY device. Signed-off-by: Herve Codina <herve.codina@bootlin.com> Link: https://lore.kernel.org/r/20220429134143.628428-8-herve.codina@bootlin.com Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2022-05-06ARM: dts: r9a06g032: Add USB PHY DT supportHerve Codina1-0/+6
Define the r9a06g032 generic part of the USB PHY device node. Signed-off-by: Herve Codina <herve.codina@bootlin.com> Link: https://lore.kernel.org/r/20220429134143.628428-7-herve.codina@bootlin.com Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2022-05-06ARM: dts: r9a06g032: Add internal PCI bridge nodeHerve Codina1-0/+29
Add the device node for the r9a06g032 internal PCI bridge device. Signed-off-by: Herve Codina <herve.codina@bootlin.com> Link: https://lore.kernel.org/r/20220429134143.628428-6-herve.codina@bootlin.com Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2022-05-06ARM: dts: r9a06g032: Describe the RTCMiquel Raynal1-0/+13
Describe the SoC RTC which counts time and provides alarm support. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/r/20220429104602.368055-7-miquel.raynal@bootlin.com Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2022-05-06ARM: dts: r9a06g032: Fix the NAND controller nodeMiquel Raynal1-0/+1
Add the missing power-domains property which is mandatory. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/r/20220429105229.368728-3-miquel.raynal@bootlin.com Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2022-05-06ARM: dts: r9a06g032: Fill the UART DMA propertiesMiquel Raynal1-0/+10
UART 0 to 2 do not have DMA support, while UART 3 to 7 do. Fill the "dmas" and "dma-names" properties for each of these nodes. Please mind that these nodes go through the dmamux node which will redirect the requests to the right DMA controller. The first 4 cells of the "dmas" properties will be transferred as-is to the DMA controllers. The last 2 cells are consumed by the dmamux. Which means cell 0 and 4 are almost redundant, one giving the controller request ID and the other the dmamux channel which is a 1:1 translation of the request IDs, shifted by 16 when pointing to the second DMA controller. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/r/20220421095323.101811-11-miquel.raynal@bootlin.com Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2022-05-06ARM: dts: r9a06g032: Describe the DMA routerMiquel Raynal1-0/+10
There is a dmamux on this SoC which allows picking two different sources for a single DMA request. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20220427095653.91804-10-miquel.raynal@bootlin.com Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2022-05-06ARM: dts: r9a06g032: Add the two DMA nodesMiquel Raynal1-0/+28
Describe the two DMA controllers available on this SoC. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20220427095653.91804-9-miquel.raynal@bootlin.com Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2022-05-05arm64: dts: qcom: align DWC3 USB clocks with DT schemaKrzysztof Kozlowski2-5/+8
Align order of clocks and their names with Qualcomm DWC3 USB DT schema. No functional impact expected. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20220504131923.214367-13-krzysztof.kozlowski@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-05-05Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski36-66/+178
tools/testing/selftests/net/forwarding/Makefile f62c5acc800e ("selftests/net/forwarding: add missing tests to Makefile") 50fe062c806e ("selftests: forwarding: new test, verify host mdb entries") https://lore.kernel.org/all/20220502111539.0b7e4621@canb.auug.org.au/ Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-05-05Merge tag 'omap-for-v5.19/dt-part2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/dtArnd Bergmann18-1203/+1542
More devicetree changes for omaps Devicetree updates for few boards and more clean-up for make dtbs warnings: - Updates for am335x-myirtech oscillator and mtd - Firmware configuration for i2c voltage scaling and IO isolation for am3/4 that are wired for these features - A series of omap3 clock node clean-up for make dtbs warnings for unique_unit_address and node_name_chars_strict - Updates for dma-channel usage to add the generic dma-common properties * tag 'omap-for-v5.19/dt-part2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (26 commits) ARM: dts: dm81xx: use new 'dma-channels/requests' properties ARM: dts: am33xx: use new 'dma-channels/requests' properties ARM: dts: Group omap3 CM_CLKSEL1_EMU clocks ARM: dts: Group omap3 CM_CLKSEL_PER clocks ARM: dts: Group omap3 CM_ICLKEN_PER clocks ARM: dts: Group omap3 CM_FCLKEN_PER clocks ARM: dts: Group omap3 CM_FCLKEN_CAM clocks ARM: dts: Group omap3 CM_CLKSEL_DSS clocks ARM: dts: Group omap3 CM_FCLKEN_DSS clocks ARM: dts: Group omap3 CM_CLKOUT_CTRL clocks ARM: dts: Group omap3 CM_CLKSEL1_PLL clocks ARM: dts: Group omap3 CM_CLKSEL_WKUP clocks ARM: dts: Group omap3 CM_ICLKEN_WKUP clocks ARM: dts: Group omap3 CM_FCLKEN_WKUP clocks ARM: dts: Group omap3 CM_CLKSEL_CORE clocks ARM: dts: Group omap3 CM_ICLKEN3_CORE clocks ARM: dts: Group omap3 CM_ICLKEN1_CORE clocks ARM: dts: Group omap3 crypto accelerator clocks ARM: dts: Group omap3 CM_FCLKEN1_CORE clocks ARM: dts: Group omap3 CONTROL_DEVCONF1 clocks ... Link: https://lore.kernel.org/r/pull-1651726643-535261@atomide.com Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-05-05Merge tag 'arm-soc/for-5.19/devicetree' of https://github.com/Broadcom/stblinux into arm/dtArnd Bergmann39-156/+555
This pull request contains Broadcom ARM-based SoCs Device Tree changes for 5.19, please pull the following: - Oleksij fixes the ethernet node name for the USB Ethernet adapter on BCM283x (Raspberry Pi 1/2/3) platforms - Kuldeep fixes the PL022 SPI controller clock names to conform to the binding - Rafal updates the various BCM5301X (Northstar) Device Tree include files to be dtsschema conforming for pinctrl, NAND - Arinc adds the Asus RT-AC88U binding, removes some unnecessary properties of the Ethernet switch DT node, populates the correct PHY interface for port 5 of the switch, adds support for fetching the MAC address from the NVMEM provider and finally disables gmac0 on that device which is unused - Phil updates the Raspberry Pi 1/2/3 DTS files to have the latest gpio line names conforming to the printed circuit board layout - Krzysztof updates various Broadcom DTS files to have a conforming SPI nor Device Tree node - Takayoshi adds support for the Buffalo WZR-1166DHP/WZR-1166DHP2 wireless routers based on the BCM4708 SoC - William adds support for the BCM47622 ARMv7 Broadband SoC and provides a basic DTS to boot upstream Linux on such a system * tag 'arm-soc/for-5.19/devicetree' of https://github.com/Broadcom/stblinux: (22 commits) ARM: dts: BCM5301X: Add DT for WZR-1166DHP,DHP2 ARM: dts: add dts files for bcmbca soc 47622 dt-bindings: arm: add bcmbca device tree binding document ARM: dts: bcm283x: Align ETH_CLK GPIO line name ARM: dts: bcm283x: Remove gpio line name NC ARM: dts: bcm2835-rpi-b: Fix GPIO line names ARM: dts: bcm2837-rpi-3-b-plus: Fix GPIO line name of power LED ARM: dts: bcm2837-rpi-cm3-io3: Fix GPIO line names for SMPS I2C ARM: dts: bcm2835-rpi-zero-w: Fix GPIO line name for Wifi/BT ARM: dts: BCM5301X: Disable gmac0 and enable port@8 on Asus RT-AC88U ARM: dts: broadcom: align SPI NOR node name with dtschema dt-bindings: arm: bcm: add bindings for Asus RT-AC88U ARM: dts: BCM5301X: Fix compatible strings for BCM53012 and BCM53016 SoC dt-bindings: arm: bcm: create new description for BCM53016 dt-bindings: arm: bcm: fix BCM53012 and BCM53016 SoC strings ARM: dts: BCM5301X: Retrieve gmac1 MAC address from NVRAM on Asus RT-AC88U ARM: dts: BCM5301X: Add rgmii to port@5 of Broadcom switch on Asus RT-AC88U ARM: dts: BCM5301X: Remove cell properties from srab ports on Asus RT-AC88U ARM: dts: BCM5301X: Fix DTC warning for NAND node ARM: dts: BCM5301X: Update pin controller node name ... Link: https://lore.kernel.org/r/20220504210942.1838248-2-f.fainelli@gmail.com Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-05-05Merge tag 'stm32-dt-for-v5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/dtArnd Bergmann18-10/+1203
STM32 DT for v5.19, round 1 Highlights: ---------- -MCU: -Fix pinctrl node names to match with pinctrl yaml. - MPU: -General: - Fix pinctrl node names to match with pinctrl yaml. - Add Protonics boards support based on STM32MP151A SoC: - PRTT1C - 10BaseT1L switch: mainly embeds a sja1105q switch with TI and Micrel 10BaseT Phys and wifi support. - PRTT1S - 10BaseT1L CO2 sensor board: mainly embeds I2C humidity and CO2 sensors. - PRTT1A - 10BaseT1L multi functional controller. - ST boards: - Add RTC support on stm32mp13. - Add button and heartbit support on stm32mp13 DK board. - Add a secure version of STM32MP15 ED1/EV1/DK1/DK2 boards based on OP-TEE OS and SCMI protocol. - DH boards: - Use MCO2 to generate PHY clock and ETHRX clock in order to release internal PLL for a better SD card usage. - Add 1ms PHY post-reset on Avenger96 board to match with PHY requirements. * tag 'stm32-dt-for-v5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (24 commits) ARM: dts: stm32: Add SCMI version of STM32 boards (DK1/DK2/ED1/EV1) dt-bindings: arm: stm32: Add SCMI version of STM32 boards (DK1/DK2/ED1/EV1) ARM: dts: stm32: enable optee firmware and SCMI support on STM32MP15 dt-bindings: reset: stm32mp15: rename RST_SCMI define dt-bindings: clock: stm32mp15: rename CK_SCMI define dt-bindings: clock: stm32mp1: describes clocks if "st,stm32mp1-rcc-secure" dt-bindings: rcc: Add optional external ethernet RX clock properties ARM: dts: stm32: add UserPA13 button on stm32mp135f-dk ARM: dts: stm32: add blue led (Linux heartbeat) on stm32mp135f-dk ARM: dts: stm32: add EXTI interrupt-parent to pinctrl node on stm32mp131 ARM: dts: stm32: add support for Protonic PRTT1x boards ARM: dts: stm32: stm32mp15-pinctrl: add spi1-1 pinmux group dt-bindings: net: silabs,wfx: add prt,prtt1c-wfm200 antenna variant dt-bindings: arm: stm32: Add compatible strings for Protonic T1L boards dt-bindings: arm: stm32: correct blank lines dt-bindings: arm: stm32: narrow DH STM32MP1 SoM boards ARM: dts: stm32: enable RTC support on stm32mp135f-dk ARM: dts: stm32: add RTC node on stm32mp131 ARM: dts: stm32: Fix PHY post-reset delay on Avenger96 ARM: dts: stm32: fix pinctrl node name warnings (MPU soc) ... Link: https://lore.kernel.org/r/5818c943-882d-7e50-430d-ae3299a108ee@foss.st.com Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-05-05ARM: dts: imx7d-smegw01: Add support for i.MX7D SMEGW01 boardFabio Estevam2-0/+470
Add support for the i.MX7D SMEGW01 board. This is a gateway board that supports the following peripherals: - eMMC / SD card - RTC - USB modem - Wifi via SDIO - Dual Ethernet - CAN - Serial SRAM Signed-off-by: Fabio Estevam <festevam@denx.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2022-05-05ARM: dts: imx6qdl-udoo: Disable USB host to work around boot issuesMark Brown1-1/+1
Attempting to boot my Udoo Dual and Quad with mainline hangs during boot after printing: [ 3.270471] imx_usb 2184000.usb: No over current polarity defined [ 3.922502] mxs_phy 20c9000.usbphy: Data pin can't make good contact. [ 3.940097] imx_usb 2184200.usb: No over current polarity defined where imx_usb 2184200.usb is usbh1 in the DT. Adding debug prints to the code seems to show that we lock up at the first read in usbmisc_imx6q_init() which in combination with the above logging about the USB controllers suggests that we lock up on the first read in usbmisc_imx6q_init(). Looking at some of the other i.MX6 boards and the warning messages that are being printed suggests that there is bitrot in the DTS for the device so disable it for now, with it disabled the board boots successfully. Clearly this is not a real fix, but it does allow some use of the board with mainline. Similar behaviour is seen all the way back as far as v4.19, I tried going back to when the board was added but had toolchain issues. Vendor provided binaries seem fine on the boards so it seems likely that the hardware is fine and the issue is with some combination of the DT and kernel. This should obviously be resolved properly but for now this at least allows the kernel to boot with reduced functionality on these systems. Signed-off-by: Mark Brown <broonie@kernel.org> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2022-05-05ARM: dts: imx27: use new 'dma-channels' propertyKrzysztof Kozlowski1-1/+1
The '#dma-channels' property was deprecated in favor of one defined by generic dma-common DT bindings. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2022-05-05ARM: dts: imx6qdl-phytec: Add LED labelsAlexander Shiyan1-2/+2
This allows boards the option of adding properties or disabling the LEDs entirely. Signed-off-by: Alexander Shiyan <eagle.alexander923@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2022-05-05ARM: dts: ls1021a: reduce the interrupt-map-maskMichael Walle1-1/+1
Reduce the interrupt-map-mask of the external interrupt controller to 7 to align with the devicetree schema. Signed-off-by: Michael Walle <michael@walle.cc> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2022-05-05ARM: dts: imx6sl: Add a label for the cpu nodeFabio Estevam1-1/+1
Add a label for the cpu node, so that board devicetree files can reference to the CPU node. This is useful for describing a PMIC voltage that supplies the CPU voltage. For example: &cpu0 { cpu-supply = <&sw1_reg>; Signed-off-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2022-05-05ARM: dts: imx6ul-kontron-n6x1x-s: Use the standard 'uart-has-rtscts'Fabio Estevam1-1/+1
The usage of the 'fsl,uart-has-rtscts' property is deprecated. Use the standard 'uart-has-rtscts' instead. Cc: Frieder Schrempf <frieder.schrempf@kontron.de> Signed-off-by: Fabio Estevam <festevam@denx.de> Acked-by: Frieder Schrempf <frieder.schrempf@kontron.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2022-05-05ARM: dts: imx6dl-plybas: Use the standard 'uart-has-rtscts'Fabio Estevam1-1/+1
The usage of the 'fsl,uart-has-rtscts' property is deprecated. Use the standard 'uart-has-rtscts' instead. Cc: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Fabio Estevam <festevam@denx.de> Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2022-05-05ARM: dts: mba6ulx: Remove unnecessary #address-cells/#size-cellsFabio Estevam1-2/+0
The following W=1 dtc warning is seen: arch/arm/boot/dts/mba6ulx.dtsi:33.26-64.4: Warning (avoid_unnecessary_addr_size): /gpio-keys: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property Remove the unnecessary #address-cells/#size-cells to fix it. Fixes: 7b8861d8e627 ("ARM: dts: imx6ul: add TQ-Systems MBa6ULx device trees") Signed-off-by: Fabio Estevam <festevam@denx.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2022-05-05ARM: dts: update ifc node name to be memory-controllerLi Yang1-1/+1
Update the node name to be align with latest binding. Signed-off-by: Li Yang <leoyang.li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2022-05-05ARM: dts: ls1021a: remove "simple-bus" compatible from ifc nodeLi Yang1-1/+1
The binding of ifc device has been updated. Update dts to match accordingly. Signed-off-by: Li Yang <leoyang.li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2022-05-04ARM: dts: stm32: Add SCMI version of STM32 boards (DK1/DK2/ED1/EV1)Alexandre Torgue5-0/+376
Add a "secure" version based on SCMI of STM32 boards. Only boards provided by STMicroelectronics are concerned: -STM32MP157A-DK1 -STM32MP157C-DK2 -STM32MP157C-ED1 -STM32MP157C-EV1 Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2022-05-04ARM: dts: stm32: enable optee firmware and SCMI support on STM32MP15Alexandre Torgue1-0/+41
Enable optee and SCMI clocks/reset protocols support. Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
2022-05-04ARM: dts: socfpga: drop useless 'dma-channels/requests' propertiesKrzysztof Kozlowski2-4/+0
The pl330 DMA controller provides number of DMA channels and requests through its registers, so duplicating this information (with a chance of mistakes) in DTS is pointless. Additionally the DTS used always wrong property names which causes DT schema check failures - the bindings documented 'dma-channels' and 'dma-requests' properties without leading hash sign. Reported-by: Rob Herring <robh@kernel.org> Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20220430121902.59895-3-krzysztof.kozlowski@linaro.org
2022-05-04ARM: dts: zynq-7000: drop useless 'dma-channels/requests' propertiesKrzysztof Kozlowski1-2/+0
The pl330 DMA controller provides number of DMA channels and requests through its registers, so duplicating this information (with a chance of mistakes) in DTS is pointless. Additionally the DTS used always wrong property names which causes DT schema check failures - the bindings documented 'dma-channels' and 'dma-requests' properties without leading hash sign. Reported-by: Rob Herring <robh@kernel.org> Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Acked-by: Michal Simek <michal.simek@amd.com> Link: https://lore.kernel.org/r/20220430121902.59895-2-krzysztof.kozlowski@linaro.org
2022-05-04ARM: dts: exynos: drop useless 'dma-channels/requests' propertiesKrzysztof Kozlowski6-34/+0
The pl330 DMA controller provides number of DMA channels and requests through its registers, so duplicating this information (with a chance of mistakes) in DTS is pointless. Additionally the DTS used always wrong property names which causes DT schema check failures - the bindings documented 'dma-channels' and 'dma-requests' properties without leading hash sign. Reported-by: Rob Herring <robh@kernel.org> Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20220430121902.59895-8-krzysztof.kozlowski@linaro.org
2022-05-04ARM: dts: s5pv210: drop useless 'dma-channels/requests' propertiesKrzysztof Kozlowski1-6/+0
The pl330 DMA controller provides number of DMA channels and requests through its registers, so duplicating this information (with a chance of mistakes) in DTS is pointless. Additionally the DTS used always wrong property names which causes DT schema check failures - the bindings documented 'dma-channels' and 'dma-requests' properties without leading hash sign. Reported-by: Rob Herring <robh@kernel.org> Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20220430121902.59895-7-krzysztof.kozlowski@linaro.org
2022-05-03ARM: dts: BCM5301X: Add DT for WZR-1166DHP,DHP2SHIMAMOTO Takayoshi4-0/+246
Buffalo WZR-1166DHP/WZR-1166DHP2 wireless router with - BCM4708A0 - 128MiB NAND flash - 2T2R 11ac/a/b/g/n Wi-Fi - 4x 10/100/1000M ethernet switch - 1x USB 3.0 port WZR-1166DHP and WZR-1166DHP2 have different memory capacity. WZR-1166DHP - 512 MiB DDR2 SDRAM WZR-1166DHP2 - 256 MiB DDR2 SDRAM These hardware components are very similar to the WZR-1750DHP except for the number of antennas. Signed-off-by: SHIMAMOTO Takayoshi <takayoshi.shimamoto.360@gmail.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2022-05-03ARM: dts: qcom: msm8974-FP2: Add supplies for remoteprocsLuca Weiss1-0/+11
Those were removed from msm8974.dtsi as part of a recent cleanup commit, so add them back for FP2. Signed-off-by: Luca Weiss <luca@z3ntu.xyz> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20220421214243.352469-3-luca@z3ntu.xyz
2022-05-03ARM: dts: qcom: msm8974-FP2: Configure chargerLuca Weiss1-0/+10
Set the relevant properties on the smbb charger to allow the device to charge properly. Signed-off-by: Luca Weiss <luca@z3ntu.xyz> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20220421214243.352469-2-luca@z3ntu.xyz
2022-05-03ARM: dts: qcom: msm8974-FP2: Add support for touchscreenLuca Weiss1-0/+15
Configure the touchscreen found on the new display module of the FP2. To add some detail, FP2 has two different screen/touchscreen variants ("display module"), the old module has Synaptics touchscreen, the new one this Ilitek touchscreen. We're only supporting the new display module for now. Signed-off-by: Luca Weiss <luca@z3ntu.xyz> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20220421214243.352469-1-luca@z3ntu.xyz
2022-05-03ARM: dts: qcom: sdx55: Remove ipa interconnect nodeStephen Boyd1-7/+0
This device node is unused now that we've removed the driver that consumed it in the kernel. Drop the unused node to save some space. Cc: Alex Elder <elder@linaro.org> Cc: Taniya Das <quic_tdas@quicinc.com> Cc: Mike Tipton <quic_mdtipton@quicinc.com> Cc: Georgi Djakov <djakov@kernel.org> Signed-off-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Alex Elder <elder@linaro.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20220415005828.1980055-2-swboyd@chromium.org
2022-05-03ARM: dts: exynos: add atmel,24c128 fallback to Samsung EEPROMKrzysztof Kozlowski1-2/+2
The Samsung s524ad0xd1 EEPROM should use atmel,24c128 fallback, according to the AT24 EEPROM bindings. Reported-by: Rob Herring <robh@kernel.org> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20220426183443.243113-1-krzysztof.kozlowski@linaro.org
2022-05-03Merge tag 'aspeed-v5.18-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/bmc into arm/fixesArnd Bergmann3-6/+18
ASPEED device tree fixes for v5.18 - Quad SPI device tree corrections - Reinstate GFX node that was removed - romed8hm3 machine fixes * tag 'aspeed-v5.18-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/bmc: ARM: dts: aspeed: Add video engine to g6 ARM: dts: aspeed: romed8hm3: Fix GPIOB0 name ARM: dts: aspeed: romed8hm3: Add lm25066 sense resistor values ARM: dts: aspeed-g6: fix SPI1/SPI2 quad pin group ARM: dts: aspeed-g6: add FWQSPI group in pinctrl dtsi dt-bindings: pinctrl: aspeed-g6: add FWQSPI function/group pinctrl: pinctrl-aspeed-g6: add FWQSPI function-group dt-bindings: pinctrl: aspeed-g6: remove FWQSPID group pinctrl: pinctrl-aspeed-g6: remove FWQSPID group in pinctrl ARM: dts: aspeed-g6: remove FWQSPID group in pinctrl dtsi Link: https://lore.kernel.org/r/CACPK8XdhLfafOfqvR0r7p6V6AhtNXD4uZGaz7Y+Y4P-rc9p0tQ@mail.gmail.com Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-05-03ARM: dts: stm32: add UserPA13 button on stm32mp135f-dkFabien Dessenne1-0/+11
The PA13 user button is connected to the PA13 pin of the stm32mp135f-dk board. It requires an internal pull-up configuration. Signed-off-by: Fabien Dessenne <fabien.dessenne@foss.st.com> Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Copyright © 1996 – 2026 Jason A. Donenfeld. All Rights Reverse Engineered.