| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull arm SoC platform updates from Olof Johansson:
"SoC updates, mostly refactorings and cleanups of old legacy platforms,
but also a few more things:
New SoC support this release:
- NXP/Freescale i.MX7ULP (1x Cortex-A7, Cortex-M4, graphics, etc)
- Allwinner F1C100, older platform with an ARM926-EJS (ARMv5) core
Cleanups of various platforms:
- OMAP1 ams-delta does some GPIO cleanups
- Davinci removes of at24 platform data
- Samsung cleans up old wakeup, PM debug and secondary core boot code
- Renesas moves around config options and PM code to drivers/soc for
sharing with 64-bit and more consistency
- i.MX, Broadcom and SoCFPGA all have tweaks to lowlevel debug
console setups
- SoCFPGA adds explicit selection of ARM errata and removes some
unused code
This also contains a few patches that I had queued up as fixes for
4.20 but didn't send in before the release"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (68 commits)
arm64: dts: renesas: draak: Fix CVBS input
ARM: omap2: avoid section mismatch warning
ARM: tegra: avoid section mismatch warning
ARM: ks8695: fix section mismatch warning
ARM: pxa: avoid section mismatch warning
ARM: mmp: fix pxa168_device_usb_phy use on aspenite
ARM: mmp: fix timer_init calls
ARM: OMAP1: fix USB configuration for device-only setups
ARM: OMAP1: add MMC configuration for Palm Tungsten E
ARM: imx: fix dependencies on imx7ulp
ARM: meson: select HAVE_ARM_TWD and ARM_GLOBAL_TIMER
MAINTAINERS: add drivers/soc/amlogic/ to amlogic list
ARM: imx: add initial support for imx7ulp
ARM: debug-imx: only define DEBUG_IMX_UART_PORT if needed
ARM: dts: Fix OMAP4430 SDP Ethernet startup
ARM: dts: am335x-pdu001: Fix polarity of card detection input
ARM: OMAP1: ams-delta: Fix audio permanently muted
ARM: dts: omap5: Fix dual-role mode on Super-Speed port
arm64: dts: rockchip: fix rk3399-rockpro64 regulator gpios
ARM: davinci: da850-evm: remove unnecessary include
...
|
|
Before things go out of hand, make it possible to pass
flags when requesting "own" descriptors from a gpio_chip.
This is necessary if the chip wants to request a GPIO with
active low semantics, for example.
Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Roger Quadros <rogerq@ti.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Now as the board header file is no longer included by drivers, move it
to the root directory of mach-omap1.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Instead of exporting the FIQ buffer symbol to be used in
ams-delta-serio driver, pass it to the driver as platform_data.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The driver still obtains IRQ number from a hardcoded GPIO. Use IRQ
resource instead.
For this to work on Amstrad Delta, add the IRQ resource to
ams-delta-serio platform device structure. Obtain the IRQ number
assigned to "keybrd_clk" GPIO pin from FIQ initialization routine.
As a benefit, the driver no longer needs to include
<mach/board-ams-delta.h>.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Split the header file into two parts and move them to directories where
they belong.
Information on internal structure of FIQ buffer is moved to
<linux/platform_data/ams-delta-fiq.h> for ams-delta-serio driver use.
Other information used by ams-delta board init file and FIQ code is
made local to mach-omap1 root directory.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
From the very beginning, input GPIO pins of ams-delta serio port have
been used by FIQ handler, not serio driver.
Don't request those pins from the ams-delta-serio driver any longer,
instead keep them requested and initialized by the FIQ initialization
routine which already requests them and releases while identifying GPIO
IRQs.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
With introduction of GPIO lookup tables to Amstrad Delta board init
file, semantics of symbols representing OMAP GPIO pins defined in
<mach/board-ams-delta.h> changed from statically assigned global GPIO
numbers to hardware pin numbers local to OMAP "gpio-0-15" chip.
This patch modifies deferred FIQ interrupt handler so it no longer uses
static GPIO numbers in favour of IRQ data descriptors obtained at FIQ
initialization time from descriptor of the GPIO chip with use of its
hardware pin numbers. The chip descriptor is passed from the board
init file.
As a benefit, the deferred FIQ handler should work faster.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
[tony@atomide.com: removed duplicate gpiochip_match_by_label]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The deferred_fiq handler used to limit hardware operations to IRQ
unmask only, relying on gpio-omap assigned handler performing the ACKs.
Since commit 80ac93c27441 ("gpio: omap: Fix lost edge interrupts") this
is no longer the case as handle_edge_irq() has been replaced with
handle_simmple_irq() which doesn't touch the hardware.
Add single ACK operation per each active IRQ pin to the handler. While
being at it, move unmask operation out of irq_counter loop so it is
also called only once for each active IRQ pin.
Fixes: 80ac93c27441 ("gpio: omap: Fix lost edge interrupts")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Pull ARM SoC platform updates from Olof Johansson:
"Improved and new platform support for various SoCs:
New SoC support:
- Broadcom BCM23550
- Freescale i.MX7Solo
- Qualcomm MDM9615
- Renesas r8a7792
Improvements:
- convert clps711x to multiplatform
- debug uart improvements for Atmel platforms
- Tango platform improvements: HOTPLUG_CPU, Suspend-to-ram
- OMAP tweaks and improvements to hwmod
- OMAP support for kexec on SMP"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (109 commits)
ARM: davinci: fix build break because of undeclared dm365_evm_snd_data
ARM: s3c64xx: smartq: Avoid sparse warnings
ARM: sti: Implement dummy L2 cache's write_sec
ARM: STi: Update machine _namestr to be more generic.
arm: meson: explicitly select clk drivers
ARM: tango: add Suspend-to-RAM support
ARM: hisi: consolidate the hisilicon machine entries
ARM: tango: fix CONFIG_HOTPLUG_CPU=n build
MAINTAINERS: Update BCM281XX/BCM11XXX/BCM216XX entry
MAINTAINERS: Update BCM63XX entry
MAINTAINERS: Add NS2 entry
MAINTAINERS: Fix nsp false-positives
MAINTAINERS: Change L to M for Broadcom ARM/ARM64 SoC entries
ARM: debug: Enable DEBUG_BCM_5301X for Northstar Plus SoCs
ARM: clps711x: Switch to MULTIPLATFORM
ARM: clps711x: Remove boards support
ARM: clps711x: Add basic DT support
ARM: clps711x: Reduce static map size
ARM: SAMSUNG: Constify iomem address passed to s5p_init_cpu
ARM: oxnas: Change OX810SE default driver config
...
|
|
After OMAP1 IRQ definitions have been changed by commit 685e2d08c54b
("ARM: OMAP1: Change interrupt numbering for sparse IRQ") introduced
in v4.2, ams-delta FIQ handler which depends on them no longer works
as expected. Fix it.
Created and tested on Amstrad Delta against Linux-4.7-rc3
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
8435cf757 (arm: Replace various irq_desc accesses) typoed
irq_get_irq_chip() instead of irq_get_chip().
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Use the proper functions. There is no need to fiddle with irq_desc.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>C
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: arm <linux-arm-kernel@lists.infradead.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Link: http://lkml.kernel.org/r/20140223212737.099151500@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
This is only used by omap1.
And to fix things properly, this should not be included
from the drivers at all.
Acked-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Cc: linux-mtd@lists.infradead.org
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: linux-input@vger.kernel.org
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Liam Girdwood <lrg@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: alsa-devel@alsa-project.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Pull first batch of arm-soc cleanups from Olof Johansson:
"These cleanups are basically all over the place. The idea is to
collect changes with minimal impact but large number of changes so we
can avoid them from distracting in the diffstat in the other series.
A significant number of lines get removed here, in particular because
the ixp2000 and ixp23xx platforms get removed. These have never been
extremely popular and have fallen into disuse over time with no active
maintainer taking care of them. The u5500 soc never made it into a
product, so we are removing it from the ux500 platform.
Many good cleanups also went into the at91 and omap platforms, as has
been the case for a number of releases."
Trivial modify-delete conflicts in arch/arm/mach-{ixp2000,ixp23xx}
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (152 commits)
ARM: clps711x: Cleanup IRQ handling
ARM clps711x: Removed unused header mach/time.h
ARM: clps711x: Added note about support EP731x CPU to Kconfig
ARM: clps711x: Added missing register definitions
ARM: clps711x: Used own subarch directory for store header file
Dove: Fix Section mismatch warnings
ARM: orion5x: ts78xx debugging changes
ARM: orion5x: remove PM dependency from ts78xx
ARM: orion5x: ts78xx fix NAND resource off by one
ARM: orion5x: ts78xx whitespace cleanups
Orion5x: Fix Section mismatch warnings
Orion5x: Fix warning: struct pci_dev declared inside paramter list
ARM: clps711x: Combine header files into one for clps711x-targets
ARM: S3C24XX: Use common macro to define resources on mach-qt2410.c
ARM: S3C24XX: Use common macro to define resources on mach-osiris.c
ARM: EXYNOS: Adapt to cpuidle core time keeping and irq enable
ARM: S5PV210: Use common macro to define resources on mach-smdkv210.c
ARM: S5PV210: Use common macro to define resources on dev-audio.c
ARM: S5PC100: Use common macro to define resources on dev-audio.c
ARM: S5P64X0: Use common macro to define resources on dev-audio.c
...
|
|
Commit 384ebe1c2849160d040df3e68634ec506f13d9ff, "gpio/omap: Add DT
support to GPIO driver", introduced dynamic IRQ numbering of OMAP GPIO
interrupts, breaking all IH_GPIO_BASE based IRQ number calculations.
This issue was corrected in the OMAP GPIO driver and the related header
file with commit 25db711df3258d125dc1209800317e5c0ef3c870, "gpio/omap:
Fix IRQ handling for SPARSE_IRQ".
However, the Amstrad Delta FIQ handler, which replaces the gpio-omap
driver in serving GPIO interrupts on this board, still uses that
outdated method. Fix it.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
sparse warns when 0 is passed to a function expecting a pointer argument.
Resolve these warnings by replacing the 0 with NULL.
arch/arm/plat-omap/include/plat/dmtimer.h:319:34: warning: Using plain integer as NULL pointer
arch/arm/plat-omap/include/plat/dmtimer.h:324:35: warning: Using plain integer as NULL pointer
arch/arm/mach-omap2/irq.c:294:22: warning: Using plain integer as NULL pointer
arch/arm/mach-omap1/board-palmz71.c:292:50: warning: Using plain integer as NULL pointer
arch/arm/mach-omap1/board-palmz71.c:295:73: warning: Using plain integer as NULL pointer
arch/arm/mach-omap1/ams-delta-fiq.c:105:63: warning: Using plain integer as NULL pointer
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
There's no need to have these in plat/io.h.
While at it, clean up the includes to group them
like they typically are grouped.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
|
|
This patch introduces an IRQ handler used for processing interrupts generated
by the FIQ handler when it decides there are data ready for processing.
The handler further invokes device specific interrupt routines based on
interrupt source counters passed from the FIQ handler.
The handler setup function is intended to be called from the board
provided init_machine() callback.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
[tony@atomide.com: Updated to include linux/io.h instead of plat/io.h
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
Linus Torvalds
Linus Walleij
Janusz Krzysztofik
Andrea Gelmini
Thomas Gleixner
Tony Lindgren
Janusz Krzysztofik
Paul Walmsley
Lennert Buytenhek