| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
|
|
Use irq_set_chip_and_handler() instead. Converted with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Convert to the new function names. Automated with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
hwspinlock: depend on OMAP4
ARM: OMAP2+: Fix warnings for GPMC interrupt
OMAP4: PandaBoard: remove unused power regulators
arm: mach-omap2: omap_l3_smx: fix irq handler setup
arm: mach-omap2: devices: fix omap3_l3_init() return value
|
|
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (442 commits)
[media] videobuf2-dma-contig: make cookie() return a pointer to dma_addr_t
[media] sh_mobile_ceu_camera: Do not call vb2's mem_ops directly
[media] V4L: soc-camera: explicitly require V4L2_BUF_TYPE_VIDEO_CAPTURE
[media] v4l: soc-camera: Store negotiated buffer settings
[media] rc: interim support for 32-bit NEC-ish scancodes
[media] mceusb: topseed 0x0011 needs gen3 init for tx to work
[media] lirc_zilog: error out if buffer read bytes != chunk size
[media] lirc: silence some compile warnings
[media] hdpvr: use same polling interval as other OS
[media] ir-kbd-i2c: pass device code w/key in hauppauge case
[media] rc/keymaps: Remove the obsolete rc-rc5-tv keymap
[media] remove the old RC_MAP_HAUPPAUGE_NEW RC map
[media] rc/keymaps: Rename Hauppauge table as rc-hauppauge
[media] rc-rc5-hauppauge-new: Fix Hauppauge Grey mapping
[media] rc-rc5-hauppauge-new: Add support for the old Black RC
[media] rc-rc5-hauppauge-new: Add the old control to the table
[media] rc-winfast: Fix the keycode tables
[media] a800: Fix a few wrong IR key assignments
[media] opera1: Use multimedia keys instead of an app-specific mapping
[media] dw2102: Use multimedia keys instead of an app-specific mapping
...
Fix up trivial conflicts (remove/modify and some real conflicts) in:
arch/arm/mach-omap2/devices.c
drivers/staging/Kconfig
drivers/staging/Makefile
drivers/staging/dabusb/dabusb.c
drivers/staging/dabusb/dabusb.h
drivers/staging/easycap/easycap_ioctl.c
drivers/staging/usbvideo/usbvideo.c
drivers/staging/usbvideo/vicam.c
|
|
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (90 commits)
mfd: Push byte swaps out of wm8994 bulk read path
mfd: Rename ab8500 gpadc header
mfd: Constify WM8994 write path
mfd: Push byte swap out of WM8994 bulk I/O
mfd: Avoid copying data in WM8994 I2C write
mfd: Remove copy from WM831x I2C write function
mfd: Staticise WM8994 PM ops
regulator: Add a subdriver for TI TPS6105x regulator portions v2
mfd: Add a core driver for TI TPS61050/TPS61052 chips v2
gpio: Add Tunnel Creek support to sch_gpio
mfd: Add Tunnel Creek support to lpc_sch
pci_ids: Add Intel Tunnel Creek LPC Bridge device ID.
regulator: MAX8997/8966 support
mfd: Add WM8994 bulk register write operation
mfd: Append additional read write on 88pm860x
mfd: Adopt mfd_data in 88pm860x input driver
mfd: Adopt mfd_data in 88pm860x regulator
mfd: Adopt mfd_data in 88pm860x led
mfd: Adopt mfd_data in 88pm860x backlight
mfd: Fix MAX8997 Kconfig entry typos
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-2.6: (140 commits)
MAINTAINERS: de-orphan fbdev.
MAINTAINERS: Add file pattern for fb dt bindings.
video: Move sm501fb devicetree binding documentation to a better place.
fbcon: fix situation where fbcon gets deinitialised and can't reinit.
video, sm501: add OF binding to support SM501
video, sm501: add edid and commandline support
video, sm501: add I/O functions for use on powerpc
video: Fix EDID macros H_SYNC_WIDTH and H_SYNC_OFFSET
fbcon: Bugfix soft cursor detection in Tile Blitting
video: add missing framebuffer_release in error path
video: metronomefb: add __devexit_p around reference to metronomefb_remove
video: hecubafb: add __devexit_p around reference to hecubafb_remove
drivers:video:aty:radeon_base Fix typo occationally to occasionally
atmel_lcdfb: add fb_blank function
atmel_lcdfb: implement inverted contrast pwm
video: s3c-fb: return proper error if clk_get fails
uvesafb,vesafb: create WC or WB PAT-entries
video: ffb: fix ffb_probe error path
radeonfb: Let hwmon driver probe the "monid" I2C bus
fbdev: sh_mobile_lcdc: checking NULL instead of IS_ERR()
...
|
|
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (35 commits)
ARM: Update (and cut down) mach-types
ARM: 6771/1: vexpress: add support for multiple core tiles
ARM: 6797/1: hw_breakpoint: Fix newlines in WARNings
ARM: 6751/1: vexpress: select applicable errata workarounds in Kconfig
ARM: 6753/1: omap4: Enable ARM local timers with OMAP4430 es1.0 exception
ARM: 6759/1: smp: Select local timers vs broadcast timer support runtime
ARM: pgtable: add pud-level code
ARM: 6673/1: LPAE: use phys_addr_t instead of unsigned long for start of membanks
ARM: Use long long format when printing meminfo physical addresses
ARM: integrator: add Integrator/CP sched_clock support
ARM: realview/vexpress: consolidate SMP bringup code
ARM: realview/vexpress: consolidate localtimer support
ARM: integrator/versatile: consolidate FPGA IRQ handling code
ARM: rationalize versatile family Kconfig/Makefile
ARM: realview: remove old AMBA device DMA definitions
ARM: versatile: remove old AMBA device DMA definitions
ARM: vexpress: use new init_early for clock tree and sched_clock init
ARM: realview: use new init_early for clock tree and sched_clock init
ARM: versatile: use new init_early for clock tree and sched_clock init
ARM: integrator: use new init_early for clock tree init
...
|
|
In Blaze and Panda, 32KHz clock - CLK32KG to WLAN is supplied
from Phoenix TWL6030.
Add CLK32KG platform data to blaze and omap4panda board file.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Make sure the kernel can be compiled with both OMAP2 and OMAP3 camera
support linked in, and give public symbols proper omap2/omap3 prefixes.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The omap3isp platform device requires platform data. Instead of
registering the device in omap2_init_devices(), export an
omap3_init_camera() function to fill the device structure with the
platform data pointer and register the device.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The ISP CBUFF module isn't use, its resource isn't needed.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Add new/changed base address definitions and resources for
OMAP3630 ISP.
The OMAP3430 CSI2PHY block is same as the OMAP3630 CSIPHY2
block. But the later name is chosen as it gives more symmetry
to the names.
Signed-off-by: Tuukka Toivonen <tuukkat76@gmail.com>
Signed-off-by: Vimarsh Zutshi <vimarsh.zutshi@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Conflicts:
arch/arm/mach-omap2/board-overo.c
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
|
|
Commit db97eb7dfe13f6c04f0a0e77c32e2691f563ab8b
(omap: gpmc: enable irq mode in gpmc) enabled interrupts for
GPMC (General Purpose Memory Controller). However, looks like
this patch only works on omap3. Fix the issues to avoid warnings
on omap4 during the boot.
GPMC: number of chip select is 8, CS0 to CS7. One less IRQ
allocated throws below warning at boot:
[ 0.429290] Trying to install type control for IRQ409
[ 0.429290] Trying to set irq flags for IRQ409
Resolve following warning messages in boot when irq chip is not set:
[ 0.429229] Trying to install interrupt handler for IRQ402
[ 0.429229] Trying to install interrupt handler for IRQ403
[ 0.429229] Trying to install interrupt handler for IRQ404
[ 0.429260] Trying to install interrupt handler for IRQ405
[ 0.429260] Trying to install interrupt handler for IRQ406
[ 0.429260] Trying to install interrupt handler for IRQ407
[ 0.429290] Trying to install interrupt handler for IRQ408
Resolve following warning in OMAP4:
[ 0.429290] gpmc: irq-20 could not claim: err -22
Signed-off-by: Balaji T K <balajitk@ti.com>
[tony@atomide.com: combined patches into one, updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
the pandaboard does not use the VUSIM or VAUX1 power regulators on the TWL6030
and are left floating. if the VUSIM and VAUX1 power regulators are initilized,
noise on the unloaded regulators generates an overcurrent interrupt causing the
system to power down. this patch removes the initialization of the unused power
regulators of VUSIM and VAUX1.
Signed-off-by: David Anders <x0132446@ti.com>
Acked-by: Andy Green <andy.green@linaro.org>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The handler function may be called from the point it is registered.
Since the handler inspects IRQ numbers, we must set them up before
registration.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fix the return value for the successful case.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Adding DVI support to OMAP4 PandaBoard.
PandaBoard uses TFP410 DVI Framer chip
http://focus.ti.com/lit/ds/symlink/tfp410.pdf
The TFP410 gets its power enable and display data over GPIO lines muxed
in from OMAP4430. PandaBoard supports other LCD displays through
expansion
connectors, following board rework. This will disable the DVI interface.
However, the existing mux settings remain the same
PandaBoard additionally supports display over HDMI interface. It is
mutually exclusive to display over DVI. Hence the mux settings need to
be
configured seperately, as and when HDMI is enabled
Also, I2C3 bus used for reading EDID data from DVI Monitors is
registered here. Since the design is similar to BeagleBoard, the code
for the same is taken from the kernel.org commit e3333f48dd5cb21
(omap: Adding beagle i2c eeprom driver to read EDID)
Reviewed-by: Manjunath G Kondaiah <manjugk@ti.com>
Reviewed-by: Anand Gadiyar <gadiyar@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Raghuveer Murthy <raghuveer.murthy@ti.com>
[tomi.valkeinen@ti.com: fixed conflicts with HDMI]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (258 commits)
omap: zoom: host should not pull up wl1271's irq line
arm: plat-omap: iommu: fix request_mem_region() error path
OMAP2+: Common CPU DIE ID reading code reads wrong registers for OMAP4430
omap4: mux: Remove duplicate mux modes
omap: iovmm: don't check 'da' to set IOVMF_DA_FIXED flag
omap: iovmm: disallow mapping NULL address when IOVMF_DA_ANON is set
omap2+: mux: Fix compile when CONFIG_OMAP_MUX is not selected
omap4: board-omap4panda: Initialise the serial pads
omap3: board-3430sdp: Initialise the serial pads
omap4: board-4430sdp: Initialise the serial pads
omap2+: mux: Add macro for configuring static with omap_hwmod_mux_init
omap2+: mux: Remove the use of IDLE flag
omap2+: Add separate list for dynamic pads to mux
perf: add OMAP support for the new power events
OMAP4: Add IVA OPP enteries.
OMAP4: Update Voltage Rail Values for MPU, IVA and CORE
OMAP4: Enable 800 MHz and 1 GHz MPU-OPP
OMAP3+: OPP: Replace voltage values with Macros
OMAP3: wdtimer: Fix CORE idle transition
Watchdog: omap_wdt: add fine grain runtime-pm
...
Fix up various conflicts in
- arch/arm/mach-omap2/board-omap3evm.c
- arch/arm/mach-omap2/clock3xxx_data.c
- arch/arm/mach-omap2/usb-musb.c
- arch/arm/plat-omap/include/plat/usb.h
- drivers/usb/musb/musb_core.h
|
|
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (91 commits)
ARM: 6806/1: irq: introduce entry and exit functions for chained handlers
ARM: 6781/1: Thumb-2: Work around buggy Thumb-2 short branch relocations in gas
ARM: 6747/1: P2V: Thumb2 support
ARM: 6798/1: aout-core: zero thread debug registers in a.out core dump
ARM: 6796/1: Footbridge: Fix I/O mappings for NOMMU mode
ARM: 6784/1: errata: no automatic Store Buffer drain on Cortex-A9
ARM: 6772/1: errata: possible fault MMU translations following an ASID switch
ARM: 6776/1: mach-ux500: activate fix for errata 753970
ARM: 6794/1: SPEAr: Append UL to device address macros.
ARM: 6793/1: SPEAr: Remove unused *_SIZE macros from spear*.h files
ARM: 6792/1: SPEAr: Replace SIZE macro's with SZ_4K macros
ARM: 6791/1: SPEAr3xx: Declare device structures after shirq code
ARM: 6790/1: SPEAr: Clock Framework: Rename usbd clock and align apb_clk entry
ARM: 6789/1: SPEAr3xx: Rename sdio to sdhci
ARM: 6788/1: SPEAr: Include mach/hardware.h instead of mach/spear.h
ARM: 6787/1: SPEAr: Reorder #includes in .h & .c files.
ARM: 6681/1: SPEAr: add debugfs support to clk API
ARM: 6703/1: SPEAr: update clk API support
ARM: 6679/1: SPEAr: make clk API functions more generic
ARM: 6737/1: SPEAr: formalized timer support
...
|
|
Conflicts:
arch/arm/kernel/module.c
arch/arm/mach-s5pv210/sleep.S
|
|
Conflicts:
arch/arm/Kconfig
|
|
|
|
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (172 commits)
USB: Add support for SuperSpeed isoc endpoints
xhci: Clean up cycle bit math used during stalls.
xhci: Fix cycle bit calculation during stall handling.
xhci: Update internal dequeue pointers after stalls.
USB: Disable auto-suspend for USB 3.0 hubs.
USB: Remove bogus USB_PORT_STAT_SUPER_SPEED symbol.
xhci: Return canceled URBs immediately when host is halted.
xhci: Fixes for suspend/resume of shared HCDs.
xhci: Fix re-init on power loss after resume.
xhci: Make roothub functions deal with device removal.
xhci: Limit roothub ports to 15 USB3 & 31 USB2 ports.
xhci: Return a USB 3.0 hub descriptor for USB3 roothub.
xhci: Register second xHCI roothub.
xhci: Change xhci_find_slot_id_by_port() API.
xhci: Refactor bus suspend state into a struct.
xhci: Index with a port array instead of PORTSC addresses.
USB: Set usb_hcd->state and flags for shared roothubs.
usb: Make core allocate resources per PCI-device.
usb: Store bus type in usb_hcd, not in driver flags.
usb: Change usb_hcd->bandwidth_mutex to a pointer.
...
|
|
Adding board file structure for display which adds the display
structure with HDMI as the default driver when the display init
is called.
HDMI GPIO configurations are also done in this file.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Adding board file structure for display which adds the display
structure with HDMI as the default driver when the display init
is called.
HDMI GPIO configurations are also done in this file.
Signed-off-by: Mythri P K <mythripk@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
|
|
The wl1271's irq line is completely controlled by the 1271 device, and
the host does not not need to pull it up.
While there's no functional effect, letting the host pull this line up is
just redundant, and wastes power.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This adapts the register offsets used to read the CPU DIE ID registers
when run on 44XX so they match what is in the OMAP4430 Reference Manual
page 269
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Remove duplicate mux modes to make the binary smaller:
text data bss dec hex filename
9378 24472 0 33850 843a mux44xx.o
9378 19104 0 28482 6f42 mux44xx.o
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fix compile when CONFIG_OMAP_MUX is not selected
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Use the mux framework to initialise the serial pads.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Use the mux framework to initialise the serial pads.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Use the mux framework to initialise the serial pads.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add macro for defining static pins in the board file.
We can now start implementing pin multiplexing in the platform init
code for devices that call omap_hwmod_mux_init. Currently that is
only implemented for serial.c.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Currently OMAP_DEVICE_PAD_IDLE flag is used to mux pins
dynamically. This can be simplified by using the enabled
state variable of each pad. This also fixes the issue of
the static pads not getting muxed after idling and
disable/enable state transitions.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This avoids going through the list unnecessarily when
idling devices for runtime PM.
Based on an earlier patch by sricharan <r.sricharan@ti.com>.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
|
|
Conflicts:
arch/arm/mach-omap2/pm34xx.c
|
|
The patch adds the new power management trace points for
the OMAP architecture.
The trace points are for:
- default idle handler. Since the cpuidle framework is
instrumented in the generic way there is no need to
add trace points in the OMAP specific cpuidle handler;
- SoC clocks changes (enable, disable, set_rate),
- power domain states: the desired target state and -if different-
the actually hit state.
Because of the generic nature of the changes, OMAP3 and OMAP4 are supported.
Tested on OMAP3 with suspend/resume, cpuidle, basic DVFS.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
This Patch adds OPP enteries for IVA in OMAP4 OPP Table
Tested on OMAP4430 SDP Board.
Signed-off-by: Shweta Gulati <shweta.gulati@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Update MPU, IVA and CORE voltage Rail values obtained from
OMAP4430 Data Manual Operating Condition Addendum_v0.4.
Tested on OMAP4430 SDP Board.
Signed-off-by: Shweta Gulati <shweta.gulati@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Almost all OMAP4 boards support OPP 800 MHz and OPP 1 GHz.
Enable them in OPP Table. For small minority of boards which use
OMAP4430-800 MHz device OPP 1GHz is not supported,
OPP 1GHz should be disabled from board file.
Signed-off-by: Shweta Gulati <shweta.gulati@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Since all voltage data is now centralized in oppxxx_data.c, we can replace
the values in the opp table with the macros used for voltage values.
This will avoid opp table and voltage layer having conflicting values.
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
This patch adds support for the standard push buttons available on
Overo expansion boards.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
This patch adds support for the standard LEDs on the Overo COM and expansion boards
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The ads7846 driver now requires a regulator. This patch adds the
necessary regulator to the overo board file. Without it, the
following error occurs (and the touchscreen will not function):
ads7846 spi1.0: unable to get regulator: -19
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
This patch adds DSS2 support for DVI, S-video, the 480x272 Samsung
LTE430WQ-F0C panel, and the 320x240 LG.Philips LB035Q02 panel.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
Lucas De Marchi
Thomas Gleixner
Linus Torvalds
Balaji T K
Sergio Aguirre
Laurent Pinchart
Tuukka Toivonen
Paul Mundt
Russell King
David Anders
Aaro Koskinen
Murthy, Raghuveer
K, Mythri P
Tony Lindgren
Ohad Ben-Cohen
Andy Green
R Sricharan
Jean Pihet
Shweta Gulati
Vishwanath BS
Steve Sakoman