| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Some hwmod, clockdomain, am335x fixes against v3.6-rc4.
Test logs can be found here:
http://www.pwsan.com/omap/testlogs/omap_fixes_a_3.6rc/20120904110254/
|
|
|
|
If NR_IRQS is less than MAX_IRQS, we end up writing past the
irq_target_cpu array in omap_wakeupgen_init():
/* Associate all the IRQs to boot CPU like GIC init does. */
for (i = 0; i < max_irqs; i++)
irq_target_cpu[i] = boot_cpu;
This can happen if SPARSE_IRQ is enabled as by default NR_IRQS is
set to 16. Without this patch we're overwriting other data during
the boot.
Looks like a similar fix was posted by Benoit Cousson earlier
as "ARM: OMAP2+: wakeupgen: Fix wrong array size for irq_target_cpu"
but was lost.
Cc: stable@vger.kernel.org
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
|
|
The OMAP4 sl2if IP block requires some special programming for it to
enter idle. Without this programming, it will prevent the rest of
the chip from entering full chip idle.
This patch comments out the IP block data.
Later, once the appropriate support is available, this patch can be
reverted.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Clock and module mode are explictly enable when hwmod is enabled. But if
the hwmod doesn't get ready on time, clocks are disabled but module is left
enabled.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
IVA2 hwmod resets were missing the status bit offsets. Also, as the
hwmod itself didn't have prcm info at all, resetting iva hwmod was
accessing some bogus memory addresses. Added both infos to fix this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Commit 4da71ae6 ("OMAP: clockdomain: Arch specific funcs for
clkdm_clk_enable/disable") called the OMAP2xxx-specific functions for
clockdomain wakeup and sleep. This would probably have broken
software-supervised clockdomain wakeup and sleep on OMAP3.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Jon Hunter <jon-hunter@ti.com>
Acked-by: Rajendra Nayak <rnayak@ti.com>
|
|
With commit ae6df418a21f3a361c5f9b878e32a8aba4e17692
Sub: ARM: OMAP2+: dmtimer: cleanup fclk usage)
The Timer functional clock naming convention has changed from
gptX_fck => timerXfck, and so as the timer init function
in mach-omap2/timer.c.
OMAP4 clocktree also has changed accordingly.
AM33xx Clock Tree has been merged during rc3-4 timeframe,
before above commit got merged, so similar change is required
for AM33xx as well (Change the gptX_fck => timerX_fck).
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
|
|
Fix inconsistency between mach-types and CONFIG_ name that prevents
touchbook board from booting.
Signed-off-by: Radek Pilar <mrkva@mrkva.eu>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Currently, omap2_sync32k_clocksource_init() function initializes the 32K
timer as the system clock source regardless of the CONFIG_OMAP_32K_TIMER
setting.
Fix this by providing a default implementation for
!CONFIG_OMAP_32K_TIMER case.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Small platform specific bug fixes for problems found in randconfig builds.
* randconfig/mach:
ARM: ux500: don't select LEDS_GPIO for snowball
ARM: imx: build i.MX6 functions only when needed
ARM: imx: select CPU_FREQ_TABLE when needed
ARM: imx: fix ksz9021rn_phy_fixup
ARM: imx: build pm-imx5 code only when PM is enabled
ARM: omap: allow building omap44xx without SMP
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The new omap4 cpuidle implementation currently requires
ARCH_NEEDS_CPU_IDLE_COUPLED, which only works on SMP.
This patch makes it possible to build a non-SMP kernel
for that platform. This is not normally desired for
end-users but can be useful for testing.
Without this patch, building rand-0y2jSKT results in:
drivers/cpuidle/coupled.c: In function 'cpuidle_coupled_poke':
drivers/cpuidle/coupled.c:317:3: error: implicit declaration of function '__smp_call_function_single' [-Werror=implicit-function-declaration]
It's not clear if this patch is the best solution for
the problem at hand. I have made sure that we can now
build the kernel in all configurations, but that does
not mean it will actually work on an OMAP44xx.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
|
|
|
|
The 4430 OPP table was being registered for all other OMAP4 variants
too, like 4460 and 4470 causing issues with cpufreq driver
enabled. 4460 and 4470 devices have different OPPs as compared to
4430, and they should be populated seperately. As long as that
happens, let the OPP table registeration happen only on 4430 device.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
OMAP4 sleep entry code even though itself don't use many CPU registers
makes call to the v7_flush_dcache_all() which uses them. Since
v7_flush_dcache_all() doesn't make use of stack, the caller must take
care of the stack frame. Otherwise it will lead to corrupted stack frame.
Fix it by saving used registers.
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
This reverts commit 58f0829b7186150318c79515f0e0850c5e7a9c89.
Converstion to per-pwrdm per/post transition calls was a bit
premature. Only tracking MPU, PER & CORE in the idle path means we
lose the accounting for all the other powerdomains which may also
transition in idle. On OMAP3, due to autodeps, several powerdomains
transition along with MPU (e.g. DSS, USBHOST), and the accounting for
these was lost with this patch. Since the accounting includes the
context loss counters, drivers for devices in those power domains
would never notice context lost, so would likely hang after any
off-mode transitions.
This patch should be revisited when the upcoming clkdm/pwrmdm/voltdm
use-counting seires is merged since then we can properly do accounting
without relying on a call in the idle path.
In addition, the original patch had another bug because the PER
powerdomain accounting was not updated until after the GPIO resume
hook is called. Since gpio_resume_after_idle() checks the context
loss count (which is not yet updated) it would not properly restore
context, leaving the GPIO banks in an undefined state.
Cc: Jean Pihet <jean.pihet@newoldbits.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Reported-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
The SYS_NIRQ1 pin is the interupt line for the PMIC part of the TWL6030
and interrupts from the PMIC are needed as wakeup sources.
Ensure this pin is mux'd as input and has wakeup enabled so PMIC
interupts (e.g. RTC) can be used as wakeup sources.
Tested on 3430/n900, OMAP3530/Overo Fire, 3730/Overo FireSTORM,
3730/Beagle-xM.
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
remove comment for nonexistent member
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
|
|
The random config builds with PM and !ARM_CPU_SUSPEND breaks with below
error on omap2plus_defconfig.
arch/arm/mach-omap2/sleep44xx.S:323: undefined reference to `cpu_resume'
arch/arm/mach-omap2/omap-mpuss-lowpower.c:278: undefined reference to `cpu_suspend'
This is because recently merged OMAP5 platform shares the common files
with OMAP4 but doesn't select ARM_CPU_SUSPEND. Without the ARM_CPU_SUSPEND
the sleep code is meaningless.
Fix the same by adding ARM_CPU_SUSPEND for OMAP5. The suggestion came from
Russell King in an off-list discussion.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Kevin Hilman <khilman@ti.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
According to the IGEPv2 Rev.C data-sheet the LAN9221i pin 14 (IRQ) is
connected to the OMAP3730 mcspi1_cs2 pin. Since this omap mux pin acts
as an IRQ line, it has to be configured as an input GPIO.
IGEPv2 platform code sets the smsc911x_cfg->gpio_irq to GPIO 176 but
since the mux pin default mode is MODE7 (safe_mode) the driver fails
when trying to register the IRQ with the following error message:
[ 1.994598] smsc911x: Driver version 2008-10-21
[ 3.704162] irq 272: nobody cared (try booting with the "irqpoll" option)
[ 3.711364] [<c001a114>] (unwind_backtrace+0x0/0xf0) from [<c009a0d4>] (__report_bad_irq+0x20/0xbc)
[ 3.720916] [<c009a0d4>] (__report_bad_irq+0x20/0xbc) from [<c009a41c>] (note_interrupt+0x1d8/0x238)
[ 3.730560] [<c009a41c>] (note_interrupt+0x1d8/0x238) from [<c0098234>] (handle_irq_event_percpu+0xc0/0x260)
[ 3.740936] [<c0098234>] (handle_irq_event_percpu+0xc0/0x260) from [<c0098410>] (handle_irq_event+0x3c/0x5c)
[ 3.751312] [<c0098410>] (handle_irq_event+0x3c/0x5c) from [<c009abe0>] (handle_level_irq+0xac/0x10c)
[ 3.761047] [<c009abe0>] (handle_level_irq+0xac/0x10c) from [<c0097a34>] (generic_handle_irq+0x30/0x48)
[ 3.770935] [<c0097a34>] (generic_handle_irq+0x30/0x48) from [<c02a6b74>] (gpio_irq_handler+0x180/0x1d4)
[ 3.780944] [<c02a6b74>] (gpio_irq_handler+0x180/0x1d4) from [<c0097a34>] (generic_handle_irq+0x30/0x48)
[ 3.790954] [<c0097a34>] (generic_handle_irq+0x30/0x48) from [<c0013e18>] (handle_IRQ+0x4c/0xac)
[ 3.800231] [<c0013e18>] (handle_IRQ+0x4c/0xac) from [<c000858c>] (omap3_intc_handle_irq+0x60/0x74)
[ 3.809783] [<c000858c>] (omap3_intc_handle_irq+0x60/0x74) from [<c04979e4>] (__irq_svc+0x44/0x60)
[ 3.819213] Exception stack(0xee42fde0 to 0xee42fe28)
[ 3.824554] fde0: 00000001 00000001 00000000 00000000 60000013 c06cce14 c06cce14 00000110
[ 3.833190] fe00: 00000000 c06ccdf4 60000013 ee41d000 fb058064 ee42fe28 c0089e08 c04976b4
[ 3.841796] fe20: 20000013 ffffffff
[ 3.845489] [<c04979e4>] (__irq_svc+0x44/0x60) from [<c04976b4>] (_raw_spin_unlock_irqrestore+0x34/0x44)
[ 3.855499] [<c04976b4>] (_raw_spin_unlock_irqrestore+0x34/0x44) from [<c0099744>] (__setup_irq+0x1b8/0x3f0)
[ 3.865875] [<c0099744>] (__setup_irq+0x1b8/0x3f0) from [<c0099a34>] (request_threaded_irq+0xb8/0x140)
[ 3.875701] [<c0099a34>] (request_threaded_irq+0xb8/0x140) from [<c0487950>] (smsc911x_drv_probe+0x75c/0x11a4)
[ 3.886260] [<c0487950>] (smsc911x_drv_probe+0x75c/0x11a4) from [<c02e9bcc>] (platform_drv_probe+0x18/0x1c)
[ 3.906707] [<c02e89b8>] (driver_probe_device+0x90/0x210) from [<c02e8bcc>] (__driver_attach+0x94/0x98)
[ 3.916625] [<c02e8bcc>] (__driver_attach+0x94/0x98) from [<c02e7298>] (bus_for_each_dev+0x50/0x7c)
[ 3.926177] [<c02e7298>] (bus_for_each_dev+0x50/0x7c) from [<c02e81d4>] (bus_add_driver+0x184/0x248)
[ 3.935821] [<c02e81d4>] (bus_add_driver+0x184/0x248) from [<c02e909c>] (driver_register+0x78/0x12c)
[ 3.945465] [<c02e909c>] (driver_register+0x78/0x12c) from [<c0008648>] (do_one_initcall+0x34/0x178)
[ 3.955108] [<c0008648>] (do_one_initcall+0x34/0x178) from [<c066e8f4>] (kernel_init+0xfc/0x1c0)
[ 3.964385] [<c066e8f4>] (kernel_init+0xfc/0x1c0) from [<c00140b0>] (kernel_thread_exit+0x0/0x8)
[ 3.973632] handlers:
[ 3.976043] [<c034e2cc>] smsc911x_irqhandler
[ 3.980560] Disabling IRQ #272
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
1) The above commit introduced a common ->get_pendown_state() function
into the generic code, but that function was board-specific for the
OMAP3EVM and thus broke most other boards using this code.
2) The above commit was mis-merged introducing another bug which
prevents the ads7846 driver probe function to succeed.
The omap_ads7846_init() function frees the pendown GPIO in case there is
no ->get_pendown_state() function set by the caller (board specific
code), so it can be requested later by the ads7846 driver.
The above commit add a common ->get_pendown_state() function without
removing the gpio_free() call and thus once the ads7846 driver tries
to use the pendown GPIO, it crashes as the pendown GPIO has not been
requested.
3) The above commit introduces NO new functionality as
get_pendown_state() function is already implemented in a suitable way by
the ads7846 driver and the debounce time handling has already been
fixed by commit 97ee9f01 (ARM: OMAP: fix the ads7846 init code).
This reverts commit 16aced80f6739beb2a6ff7b6f96c83ba80d331e8.
Conflicts:
arch/arm/mach-omap2/common-board-devices.c
Solved by taking the working version prior to the above commit.
Cc: Zumeng Chen <zumeng.chen@windriver.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Pull arm-soc cpuidle enablement for OMAP from Olof Johansson:
"Coupled cpuidle was meant to merge for 3.5 through Len Brown's tree,
but didn't go in because the pull request ended up rejected. So it
just got merged, and we got this staged branch that enables the
coupled cpuidle code on OMAP.
With a stable git workflow from the other maintainer we could have
staged this earlier, but that wasn't the case so we have had to merge
it late.
The alternative is to hold it off until 3.7 but given that the code is
well-isolated to OMAP and they are eager to see it go in, I didn't
push back hard in that direction."
* tag 'pm2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: OMAP4: CPUidle: Open broadcast clock-event device.
ARM: OMAP4: CPUidle: add synchronization for coupled idle states
ARM: OMAP4: CPUidle: Use coupled cpuidle states to implement SMP cpuidle.
ARM: OMAP: timer: allow gp timer clock-event to be used on both cpus
|
|
Pull ARM DMA engine updates from Russell King:
"This looks scary at first glance, but what it is is:
- a rework of the sa11x0 DMA engine driver merged during the previous
cycle, to extract a common set of helper functions for DMA engine
implementations.
- conversion of amba-pl08x.c to use these helper functions.
- addition of OMAP DMA engine driver (using these helper functions),
and conversion of some of the OMAP DMA users to use DMA engine.
Nothing in the helper functions is ARM specific, so I hope that other
implementations can consolidate some of their code by making use of
these helpers.
This has been sitting in linux-next most of the merge cycle, and has
been tested by several OMAP folk. I've tested it on sa11x0 platforms,
and given it my best shot on my broken platforms which have the
amba-pl08x controller.
The last point is the addition to feature-removal-schedule.txt, which
will have a merge conflict. Between myself and TI, we're planning to
remove the old TI DMA implementation next year."
Fix up trivial add/add conflicts in Documentation/feature-removal-schedule.txt
and drivers/dma/{Kconfig,Makefile}
* 'dmaengine' of git://git.linaro.org/people/rmk/linux-arm: (53 commits)
ARM: 7481/1: OMAP2+: omap2plus_defconfig: enable OMAP DMA engine
ARM: 7464/1: mmc: omap_hsmmc: ensure probe returns error if DMA channel request fails
Add feature removal of old OMAP private DMA implementation
mtd: omap2: remove private DMA API implementation
mtd: omap2: add DMA engine support
spi: omap2-mcspi: remove private DMA API implementation
spi: omap2-mcspi: add DMA engine support
ARM: omap: remove mmc platform data dma_mask and initialization
mmc: omap: remove private DMA API implementation
mmc: omap: add DMA engine support
mmc: omap_hsmmc: remove private DMA API implementation
mmc: omap_hsmmc: add DMA engine support
dmaengine: omap: add support for cyclic DMA
dmaengine: omap: add support for setting fi
dmaengine: omap: add support for returning residue in tx_state method
dmaengine: add OMAP DMA engine driver
dmaengine: sa11x0-dma: add cyclic DMA support
dmaengine: sa11x0-dma: fix DMA residue support
dmaengine: PL08x: ensure all descriptors are freed when channel is released
dmaengine: PL08x: get rid of write only pool_ctr and free_txd locking
...
|
|
Pull fbdev updates from Florian Tobias Schandinat:
- large updates for OMAP
- support for LCD3 overlay manager (omap5)
- omapdss output cleanup
- removal of passive matrix LCD support as there are no drivers for
such panels for DSS or DSS2 and nobody complained (cleanup)
- large updates for SH Mobile
- overlay support
- separating MERAM (cache) from framebuffer driver
- some updates for Exynos and da8xx-fb
- various other small patches
* tag 'fbdev-updates-for-3.6' of git://github.com/schandinat/linux-2.6: (78 commits)
da8xx-fb: fix compile issue due to missing include
fbdev: Make pixel_to_pat() failure mode more friendly
da8xx-fb: do not turn ON LCD backlight unless LCDC is enabled
fbdev: sh_mobile_lcdc: Fix vertical panning step
video: exynos mipi dsi: Fix mipi dsi regulators handling issue
video: da8xx-fb: do clock reset of revision 2 LCDC before enabling
arm: da850: configure LCDC fifo threshold
video: da8xx-fb: configure FIFO threshold to reduce underflow errors
video: da8xx-fb: fix flicker due to 1 frame delay in updated frame
video: da8xx-fb rev2: fix disabling of palette completion interrupt
da8xx-fb: add missing FB_BLANK operations
video: exynos_dp: use usleep_range instead of delay
video: exynos_dp: check the only INTERLANE_ALIGN_DONE bit during Link Training
fb: epson1355fb: Fix section mismatch
video: exynos_dp: fix wrong DPCD address during Link Training
video/smscufx: fix line counting in fb_write
aty128fb: Fix coding style issues
fbdev: sh_mobile_lcdc: Fix pan offset computation in YUV mode
fbdev: sh_mobile_lcdc: Fix overlay registers update during pan operation
fbdev: sh_mobile_lcdc: Support horizontal panning
...
|
|
DMAengine uses the DMA engine device structure when mapping/unmapping
memory for DMA, so the MMC devices do not need their DMA masks
initialized (this reflects hardware: the MMC device is not the device
doing DMA.)
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Pull ARM updates from Russell King:
"First ARM push of this merge window, post me coming back from holiday.
This is what has been in linux-next for the last few weeks. Not much
to say which isn't described by the commit summaries."
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (32 commits)
ARM: 7463/1: topology: Update cpu_power according to DT information
ARM: 7462/1: topology: factorize the update of sibling masks
ARM: 7461/1: topology: Add arch_scale_freq_power function
ARM: 7456/1: ptrace: provide separate functions for tracing syscall {entry,exit}
ARM: 7455/1: audit: move syscall auditing until after ptrace SIGTRAP handling
ARM: 7454/1: entry: don't bother with syscall tracing on ret_from_fork path
ARM: 7453/1: audit: only allow syscall auditing for pure EABI userspace
ARM: 7452/1: delay: allow timer-based delay implementation to be selected
ARM: 7451/1: arch timer: implement read_current_timer and get_cycles
ARM: 7450/1: dcache: select DCACHE_WORD_ACCESS for little-endian ARMv6+ CPUs
ARM: 7449/1: use generic strnlen_user and strncpy_from_user functions
ARM: 7448/1: perf: remove arm_perf_pmu_ids global enumeration
ARM: 7447/1: rwlocks: remove unused branch labels from trylock routines
ARM: 7446/1: spinlock: use ticket algorithm for ARMv6+ locking implementation
ARM: 7445/1: mm: update CONTEXTIDR register to contain PID of current process
ARM: 7444/1: kernel: add arch-timer C3STOP feature
ARM: 7460/1: remove asm/locks.h
ARM: 7439/1: head.S: simplify initial page table mapping
ARM: 7437/1: zImage: Allow DTB command line concatenation with ATAG_CMDLINE
ARM: 7436/1: Do not map the vectors page as write-through on UP systems
...
|
|
|
|
Pull USB patches from Greg Kroah-Hartman:
"Here's the big USB patch set for the 3.6-rc1 merge window.
Lots of little changes in here, primarily for gadget controllers and
drivers. There's some scsi changes that I think also went in through
the scsi tree, but they merge just fine. All of these patches have
been in the linux-next tree for a while now.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fix up trivial conflicts in include/scsi/scsi_device.h (same libata
conflict that Jeff had already encountered)
* tag 'usb-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (207 commits)
usb: Add USB_QUIRK_RESET_RESUME for all Logitech UVC webcams
usb: Add quirk detection based on interface information
usb: s3c-hsotg: Add header file protection macros in s3c-hsotg.h
USB: ehci-s5p: Add vbus setup function to the s5p ehci glue layer
USB: add USB_VENDOR_AND_INTERFACE_INFO() macro
USB: notify phy when root hub port connect change
USB: remove 8 bytes of padding from usb_host_interface on 64 bit builds
USB: option: add ZTE MF821D
USB: sierra: QMI mode MC7710 moved to qcserial
USB: qcserial: adding Sierra Wireless devices
USB: qcserial: support generic Qualcomm serial ports
USB: qcserial: make probe more flexible
USB: qcserial: centralize probe exit path
USB: qcserial: consolidate usb_set_interface calls
USB: ehci-s5p: Add support for device tree
USB: ohci-exynos: Add support for device tree
USB: ehci-omap: fix compile failure(v1)
usb: host: tegra: pass correct pointer in ehci_setup()
USB: ehci-fsl: Update ifdef check to work on 64-bit ppc
USB: serial: keyspan: Removed unrequired parentheses.
...
|
|
OMAP4 idle driver uses CLOCK_EVT_NOTIFY_BROADCAST_[ENTER/EXIT]
for broadcast clock events. But _ENTER/_EXIT doesn't really open
broadcast clock events and to explicitly setup the broadcast device,
CLOCK_EVT_NOTIFY_BROADCAST_ON should be used.
Add the missing CLOCK_EVT_NOTIFY_BROADCAST_ON clockevent notifications.
This will setup the broadcast timer in either periodic/oneshot modes
correctly. Recent clockevent infrastructure change 77b0d60 {leave the
broadcast device in shutdown mode when not needed} exposed this bug
leading to boot hangs in oneshot mode. Prior to this, periodic broadcast
mode was also broken. This change fixes both the periodic/oneshot broadcast
modes.
Discussion thread :
https://lkml.org/lkml/2012/4/9/13
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
With coupled idle states, a failure for any CPU to hit a low power
state must be coordinated such that all CPUs abort.
On OMAP4, when entering a coupled state, CPU0 has to wait for CPU1 to
enter its low power state before it can enter its low power state.
This is implemented by letting CPU0 wait for the CPU1 powerdomain to
hit off. However, there are conditions where CPU1 might abort/fail
and not hit off while CPU0 is waiting for it. For example, a CPU1
wakeup or a failed attempt to hit off due to hardware conditions.
To avoid the deadlock where CPU0 would continually wait for CPU1 to
hit off-mode, this patch adds a flag to signal when each CPU has come
out of its low-power state. CPU0 then checks whether CPU1 has hit off
*or* has already completed its attempt to hit off. If the latter,
CPU0 must abort its attempt to hit a low-power state so the coupled
state enter method can return.
In addition, cpuidle_coupled_parallel_barrier() is used to ensure the
clearing of the 'done' flag is synchronized on all CPUs.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
OMAP4 CPUDILE driver is converted mainly based on notes from the
coupled cpuidle patch series.
The changes include :
- Register both CPUs and C-states to cpuidle driver.
- Set struct cpuidle_device.coupled_cpus
- Set struct cpuidle_device.safe_state to non coupled state.
- Set CPUIDLE_FLAG_COUPLED in struct cpuidle_state.flags for each
state that affects multiple cpus.
- Separate ->enter hooks for coupled & simple idle.
- CPU0 wait loop for CPU1 power transition.
- CPU1 wakeup mechanism for the idle exit.
- Enabling ARCH_NEEDS_CPU_IDLE_COUPLED for OMAP4.
Thanks to Kevin Hilman and Colin Cross on the suggestions/fixes
on the intermediate version of this patch.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
For coupled cpuidle to work when both cpus are active, it needs a global timer
that can handle events for both cpus. This timer is used as the broadcast
clock-event when the per-cpu timer hardware stop in low power states.
Set the cpumask of clockevent_gpt to all cpus, set the rating correctly, and
set the irq to allow the clockevent core to determine the affinity of the
timer.
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
|
|
Pull trivial tree from Jiri Kosina:
"Trivial updates all over the place as usual."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (29 commits)
Fix typo in include/linux/clk.h .
pci: hotplug: Fix typo in pci
iommu: Fix typo in iommu
video: Fix typo in drivers/video
Documentation: Add newline at end-of-file to files lacking one
arm,unicore32: Remove obsolete "select MISC_DEVICES"
module.c: spelling s/postition/position/g
cpufreq: Fix typo in cpufreq driver
trivial: typo in comment in mksysmap
mach-omap2: Fix typo in debug message and comment
scsi: aha152x: Fix sparse warning and make printing pointer address more portable.
Change email address for Steve Glendinning
Btrfs: fix typo in convert_extent_bit
via: Remove bogus if check
netprio_cgroup.c: fix comment typo
backlight: fix memory leak on obscure error path
Documentation: asus-laptop.txt references an obsolete Kconfig item
Documentation: ManagementStyle: fixed typo
mm/vmscan: cleanup comment error in balance_pgdat
mm: cleanup on the comments of zone_reclaim_stat
...
|
|
Pull arm-soc clk changes from Arnd Bergmann:
"Clock support is moving to the clk subsystem. These tegra, omap and
imx changes are for code that is still platform specific and not (yet)
part of that subsystem."
Fix up conflicts in arch/arm/mach-{imx/clk-imx51-imx53.c,omap2/Makefile}
* tag 'clk' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
ARM: imx: clk-imx31: Fix clock id for rnga driver
ARM: imx: add missing item to the list of clock event modes
ARM: i.MX5x CSPI: Fixed clock name for CSPI
ARM: i.MX5x clocks: Fix GPT clocks
ARM: i.MX5x clocks: Fix parent for PWM clocks
ARM: i.MX5x clocks: Add EPIT support
ARM: mx27: Reenable silicon version print
ARM: clk-imx27: Fix rtc clock id
ARM: tegra: Provide clock for only one PWM controller
ARM: tegra: Fix PWM clock programming
ARM: OMAP3+: clock33xx: Add AM33XX clock tree data
ARM: OMAP3+: clock: Move common clksel_rate & clock data to common file
ARM: tegra: dma: rename driver name for clock to "tegra-apbdma"
ARM: tegra: Remove second instance of uart clk
crypto: add clk_prepare/clk_unprepare
ASoC: tegra: add clk_prepare/clk_unprepare
staging: nvec: add clk_prepare/clk_unprepare
spi/tegra: add clk_prepare/clk_unprepare
Input: tegra-kbc - add clk_prepare/clk_unprepare
USB: ehci-tegra: add clk_prepare/clk_unprepare
...
|
|
Pull arm-soc power management changes from Arnd Bergmann:
"These are various power management related changes, mainly concerning
cpuidle on i.MX and OMAP, as well as a the move of the omap
smartreflex driver to live in the power subsystem."
Fix up conflicts in arch/arm/mach-{imx/mach-imx6q.c,omap2/prm2xxx_3xxx.h}
* tag 'pm' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (37 commits)
ARM: OMAP2+: PM: fix IRQ_NOAUTOEN removal by mis-merge
ARM: OMAP2+: do not allow SmartReflex to be built as a module
ARM: OMAP2: Use hwmod to initialize mmc for 2420
ARM: OMAP3: PM: cpuidle: optimize the clkdm idle latency in C1 state
ARM: OMAP3: PM: cpuidle: optimize the PER latency in C1 state
ARM: OMAP3: PM: cpuidle: default to C1 in next_valid_state
ARM: OMAP3: PM: cleanup cam_pwrdm leftovers
ARM: OMAP3: PM: call pre/post transition per powerdomain
ARM: OMAP2+: powerdomain: allow pre/post transtion to be per pwrdm
ARM: OMAP3: PM: Remove IO Daisychain control from cpuidle
ARM: OMAP3PLUS: hwmod: reconfigure IO Daisychain during hwmod mux
ARM: OMAP3+: PRM: Enable IO wake up
ARM: OMAP4: PRM: Add IO Daisychain support
ARM: OMAP3: PM: Move IO Daisychain function to omap3 prm file
ARM: OMAP3: PM: correct enable/disable of daisy io chain
ARM: OMAP2+: PRM: fix compile for OMAP4-only build
W1: OMAP HDQ1W: use runtime PM
ARM: OMAP2+: HDQ1W: use omap_device
W1: OMAP HDQ1W: use 32-bit register accesses
W1: OMAP HDQ1W: allow driver to be built on all OMAP2+
...
|
|
Pull arm-soc board specific updates from Arnd Bergmann:
"These changes are all for individual board files. In the long run,
those files will largely go away, and the amount of changes appears to
be continuously decreasing, which is a good sign. This time around,
changes are focused on tegra, omap and samsung."
Fix conflicts in arch/arm/mach-{omap2/common-board-devices.c,tegra/Makefile.boot}
as per the 'for-linus' branch.
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
ARM: EXYNOS: Add leds status1 and status2 on Origen board
ARM: S3C64XX: Mark most Cragganmore initdata devinitdata
ARM: EXYNOS: Add missing .reserve field to SMDKC210
ARM: EXYNOS: Add DRM device to SMDK4X12 board
ARM: S3C64XX: Clean up after SPI driver platform data updates
ARM: SAMSUNG: no need to set the value for clk_xusbxti when it is 24Mhz
ARM: EXYNOS: Add framebuffer support for SMDK4X12
ARM: EXYNOS: Add HSOTG support to SMDK4X12
ARM: S5PV210: Add audio platform device in Goni board
ARM: S5PV210: Add audio platform device in Aquila board
ARM: EXYNOS: Add audio platform device in SMDKV310 board
ARM: S3C64XX: Don't specify an irq_base for WM1192-EV1 board
ARM: OMAP3: Fix omap3evm randconfig error introduced by VBUS support
ARM: OMAP: board-omap4panda: MUX configuration for sys_nirq2
ARM: OMAP: board-4430sdp: MUX configuration for sys_nirq2
ARM: OMAP3530evm: set pendown_state and debounce time for ads7846
ARM: omap3evm: enable VBUS switch for EHCI tranceiver
ARM: OMAP3EVM: Adding USB internal LDOs board file
ARM: OMAP3EVM: Add NAND flash definition
ARM: OMAP3: cm-t35: add tvp5150 decoder support
...
|
|
Pull support for three new arm SoC types from Arnd Bergmann:
- The mvebu platform includes Marvell's Armada XP and Armada 370 chips,
made by the mvebu business unit inside of Marvell. Since the same
group also made the older but similar platforms we call "orion5x",
"kirkwood", "mv78xx0" and "dove", we plan to move all of them into
the mach-mvebu directory in the future.
- socfpga is Altera's platform based on Cortex-A9 cores and a lot of
FPGA space. This is similar to the Xilinx zynq platform we already
support. The code is particularly clean, which is helped by the fact
that the hardware doesn't do much besides the parts that are expected
to get added in the FPGA.
- The OMAP subarchitecture gains support for the latest generation, the
OMAP5 based on the new Cortex-A15 core. Support is rather
rudimentary for now, but will be extended in the future.
* tag 'newsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (25 commits)
ARM: socfpga: initial support for Altera's SOCFPGA platform
arm: mvebu: generate DTBs for supported SoCs
ARM: mvebu: MPIC: read number of interrupts from control register
arm: mach-mvebu: add entry to MAINTAINERS
arm: mach-mvebu: add compilation/configuration change
arm: mach-mvebu: add defconfig
arm: mach-mvebu: add documentation for new device tree bindings
arm: mach-mvebu: add support for Armada 370 and Armada XP with DT
arm: mach-mvebu: add source files
arm: mach-mvebu: add header
clocksource: time-armada-370-xp: Marvell Armada 370/XP SoC timer driver
ARM: Kconfig update to support additional GPIOs in OMAP5
ARM: OMAP5: Add the build support
arm/dts: OMAP5: Add omap5 dts files
ARM: OMAP5: board-generic: Add device tree support
ARM: omap2+: board-generic: clean up the irq data from board file
ARM: OMAP5: Add SMP support
ARM: OMAP5: Add the WakeupGen IP updates
ARM: OMAP5: l3: Add l3 error handler support for omap5
ARM: OMAP5: gpmc: Update gpmc_init()
...
Conflicts:
Documentation/devicetree/bindings/arm/omap/omap.txt
arch/arm/mach-omap2/Makefile
drivers/clocksource/Kconfig
drivers/clocksource/Makefile
|
|
Pull arm-soc cleanups, part 2, from Arnd Bergmann:
"These omap cleanups have dependencies on earlier omap branches that in
turn depend on other cleanups, so they could not go into the same
branch."
* tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: OMAP: sdrc: Fix the build break for OMAP4 only builds
ARM: OMAP2+: dmtimer: cleanup fclk usage
ARM: OMAP2+: Fix mismerge for omap_hwmod_get_main_clk() API
ARM: OMAP2+: Remove unnecessary ifdef around __omap2_set_globals
ARM: OMAP2+: am33xx: Change cpu_is_am33xx to soc_is_am33xx
ARM: OMAP2+: am33xx: Make am33xx as a separate class
ARM: OMAP2+: Move omap3 dpll ops to dpll3xxx.c
ARM: OMAP2+: All OMAP2PLUS uses omap-device.o target so add one entry
ARM: OMAP: dmtimer: use devm_ API and do some cleanup in probe()
ARM: OMAP2+: hwmod code: add support to set dmadisable in hwmod framework
ARM: OMAP2+: PRM/CM: Move the stubbed prm and cm functions to prcm.c file and make them __weak
ARM: OMAP2+: hwmod: add omap_hwmod_get_main_clk() API
ARM: OMAP3+: dpll: optimize noncore dpll locking logic
ARM: OMAP3: control: add definition for CONTROL_CAMERA_PHY_CTRL
ARM: OMAP2+: powerdomain code: Fix Wake-up power domain power status
ARM: OMAP4: clockdomain/CM code: Update supported transition modes
ARM: OMAP3/4: omap_hwmod: Add rstst_offs field to struct omap_hwmod_omap4_prcm
ARM: OMAP2+: hwmod: Add new sysc_type3 into omap_hwmod required for am33xx
|
|
Pull arm-soc timer updates from Arnd Bergmann:
"This contains two branches dealing with timers, one for the picoxcell
platform that is now using DT with the platform-independent
dw_apb_timer driver. The other change is for the omap-specific
dmtimer driver."
* tag 'timer' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
clocksource: dw_apb_timer: Add common DTS glue for dw_apb_timer
ARM: OMAP2+: Simplify dmtimer clock aliases
ARM: OMAP2+: Move dmtimer clock set function to dmtimer driver
ARM: OMAP1: Fix dmtimer support
ARM: OMAP: Add flag to indicate if a timer needs a manual reset
ARM: OMAP: Remove timer function pointer for context loss counter
ARM: OMAP: Remove loses_context variable from timer platform data
ARM: OMAP2+: Fix external clock support for dmtimers
ARM: OMAP2+: HWMOD: Correct timer device attributes
ARM: OMAP: Add DMTIMER capability variable to represent timer features
ARM: OMAP2+: Add dmtimer platform function to reserve systimers
ARM: OMAP2+: Remove unused max number of timers definition
ARM: OMAP: Remove unnecessary clk structure
|
|
Pull arm-soc device tree description updates from Arnd Bergmann:
"This branch contains two kinds of updates: Some platforms in the
process of getting converted to device tree based booting, and the
platform specific patches necessary for that are included here.
Other platforms are already converted, so we just need to update the
actual device tree source files and the binding documents to add
support for new board and new drivers.
In the future we will probably separate those into two branches, and
in the long run, the plan is to move the device tree source files out
of the kernel repository, but that has to wait until we have completed
a much larger portion of the binding documents."
Fix up trivial conflicts in arch/arm/mach-imx/clk-imx6q.c due to newly
added clkdev registers next to a few removed unnecessary ones.
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (119 commits)
ARM: LPC32xx: Add PWM to base dts file
ARM: EXYNOS: mark the DMA channel binding for SPI as preliminary
ARM: dts: Add nodes for spi controllers for SAMSUNG EXYNOS5 platforms
ARM: EXYNOS: Enable platform support for SPI controllers for EXYNOS5
ARM: EXYNOS: Add spi clock support for EXYNOS5
ARM: dts: Add nodes for spi controllers for SAMSUNG EXYNOS4 platforms
ARM: EXYNOS: Enable platform support for SPI controllers for EXYNOX4
ARM: EXYNOS: Fix the incorrect hierarchy of spi controller bus clock
ARM: ux500: Remove PMU platform registration when booting with DT
ARM: ux500: Remove temporary snowball_of_platform_devs enablement structure
ARM: ux500: Ensure vendor specific properties have the vendor's identifier
pinctrl: pinctrl-nomadik: Append sleepmode property with vendor specific prefixes
ARM: ux500: Move rtc-pl031 registration to Device Tree when enabled
ARM: ux500: Enable the AB8500 RTC for all DT:ed DB8500 based devices
ARM: ux500: Correctly reference IRQs supplied by the AB8500 from Device Tree
ARM: ux500: Apply ab8500-debug node do the db8500 DT structure
ARM: ux500: Add a ab8500-usb Device Tree node for db8500 based devices
ARM: ux500: Add db8500 Device Tree node for misc/ab8500-pwm
ARM: ux500: Add db8500 Device Tree node for ab8500-sysctrl
ARM: ux500: Enable LED heartbeat functionality on Snowbal via DT
...
|
|
Pull arm soc-specific updates from Arnd Bergmann:
"This is stuff that does not fit well into another category and in
particular is not related to a particular board. The largest part in
here is extending the am33xx support in the omap platform."
Fix up trivial conflicts in arch/arm/mach-{imx/mach-mx35_3ds.c, tegra/Makefile}
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (74 commits)
ARM: LPC32xx: Add PWM support
ARM: LPC32xx: Add PWM clock
ARM: LPC32xx: Set system serial based on cpu unique id
ARM: vexpress: Config option for early printk console
ARM: vexpress: Add Device Tree for V2P-CA15_CA7 core tile
ARM: vexpress: Convert V2P-CA15 Device Tree to 64 bit addresses
ARM: vexpress: Add fixed regulator for SMSC
ARM: vexpress: Add missing SP804 interrupt in motherboard's DTS files
ARM: vexpress: Initial common clock support
ARM: SAMSUNG: Introduce Kconfig variable for Samsung custom clk API
ARM: EXYNOS: Add missing static storage class specifier in pmu.c file
ARM: EXYNOS: Make combiner_init function static
ARM: EXYNOS: Update HSOTG PHY clock setting for EXYNOS4X12
ARM: versatile: Make plat-versatile clock optional
ARM: vexpress: Check master site in daughterboard's sysctl operations
ARM: vexpress: remove automatic errata workaround selection
ARM: LPC32xx: Adjust to pl08x DMA interface changes
ARM: EXYNOS: Clear SYS_WDTRESET bit to use watchdog reset
ARM: imx: fix mx51 ehci setup errors
ARM: imx: make ehci power/oc polarities configurable
...
|
|
Pull general arm-soc cleanups from Arnd Bergmann:
"These are all boring changes, moving stuff around or renaming things
mostly, and also getting rid of stuff that is duplicate or should not
be there to start with. Platform-wise this is all over the place,
mainly omap, samsung, at91, imx and tegra."
Resolve trivial conflict in arch/arm/mach-omap2/clockdomains3xxx_data.c
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (67 commits)
ARM: clps711x: Remove the setting of the time
ARM: clps711x: Removed superfluous transform virt_to_bus and related functions
ARM: clps711x/p720t: Replace __initcall by .init_early call
ARM: S3C24XX: Remove unused GPIO definitions for Openmoko GTA02 board
ARM: S3C24XX: Remove unused GPIO definitions for port J
ARM: S3C24XX: Remove unused GPA, GPE, GPH bank GPIO aliases
ARM: S3C24XX: Convert the touchscreen setup code to common GPIO API
ARM: S3C24XX: Convert the PM code to gpiolib API
ARM: S3C24XX: Convert QT2410 board file to the gpiolib API
ARM: S3C24XX: Convert SMDK board file to the gpiolib API
ARM: S3C24XX: Free the backlight gpio requested in Mini2440 board code
ARM: imx: remove unused pdata from device macros
ARM: imx: Kconfig: Remove IMX_HAVE_PLATFORM_IMX_SSI from MACH_MX25_3DS
ARM: at91: fix new build errors
ARM: at91: add AIC5 support
ARM: at91: remove mach/irqs.h
ARM: at91: sparse irq support
ARM: at91: at91 based machines specify their own irq handler at run time
ARM: at91: remove static irq priorities for sam9x5
ARM: at91: add of irq priorities support
...
|
|
Pull non-critical arm-soc bug fixes from Arnd Bergmann:
"These were submitted as bug fixes before v3.5 but not considered
important enough to be included in it."
* tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (29 commits)
ARM:vt8500: Convert to use .restart and remove arch_reset()
ARM: davinci: da8xx: fix interrupt handling
ARM: OMAP2+: fix CONFIG_CPU_IDLE dependency on CONFIG_PM
ARM: mxs/tx28: fix odd include
ARM: OMAP: remove unused cpu detection macros
ARM: OMAP: fix typos related to OMAP330
ARM: OMAP7XX: Remove omap730.h and omap850.h
ARM: OMAP2+: fix naming collision of variable nr_irqs
ARM: OMAP: omap2plus_defconfig: Enable EXT4 support
ARM: OMAP depends on MMU
arm: omap3: am35x: Set proper powerdomain states
ARM: OMAP AM35x: clockdomain data: Fix clockdomain dependencies
ARM: OMAP AM35x: EMAC/MDIO integration: Add Davinci EMAC/MDIO hwmod support
ARM: OMAP: AM35xx: fix UART4 softreset
ARM: OMAP AM35xx: clock and hwmod data: fix UART4 data
ARM: OMAP AM35xx: clock and hwmod data: fix AM35xx HSOTGUSB hwmod
ARM: OMAP: Fix dts files w/ status property: "disable" -> "disabled"
ARM: OMAP: beagle: Set USB Host Port 1 to OMAP_USBHS_PORT_MODE_UNUSED
ARM: OMAP2: twl-common: Fix compiler warning
ARM: OMAP: fix the ads7846 init code
...
|
|
Linux 3.5-rc7
Prerequisite for samsung/board3 branch.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Correcting spelling typo in mach-omap2
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
From Kukjin Kim <kgene.kim@samsung.com>:
The branch includes updating each Samsung boards such as SMDK4X12,
Aquila, Goni and so on, and it is for audio platform device and
supporting of HSOTG or framebuffer.
* 'next/board-samsung-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Add framebuffer support for SMDK4X12
ARM: EXYNOS: Add HSOTG support to SMDK4X12
ARM: S5PV210: Add audio platform device in Goni board
ARM: S5PV210: Add audio platform device in Aquila board
ARM: EXYNOS: Add audio platform device in SMDKV310 board
ARM: S3C64XX: Don't specify an irq_base for WM1192-EV1 board
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
From Sascha Hauer <s.hauer@pengutronix.de>:
i.MX clk noncritical fixes and updates
* tag 'imx-clk' of git://git.pengutronix.de/git/imx/linux-2.6:
ARM: imx: clk-imx31: Fix clock id for rnga driver
ARM: imx: add missing item to the list of clock event modes
ARM: i.MX5x CSPI: Fixed clock name for CSPI
ARM: i.MX5x clocks: Fix GPT clocks
ARM: i.MX5x clocks: Fix parent for PWM clocks
ARM: i.MX5x clocks: Add EPIT support
ARM: mx27: Reenable silicon version print
ARM: clk-imx27: Fix rtc clock id
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Patches from Alexander Shiyan <shc_work@mail.ru>:
* clps711x/cleanup:
ARM: clps711x: Remove the setting of the time
ARM: clps711x: Removed superfluous transform virt_to_bus and related functions
ARM: clps711x/p720t: Replace __initcall by .init_early call
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
Tony Lindgren
Paul Walmsley
Tero Kristo
Misael Lopez Cruz
Vaibhav Hiremath
Radek Pilar
Igor Grinberg
Arnd Bergmann
Rajendra Nayak
Santosh Shilimkar
Kevin Hilman
Michael Jones
Javier Martinez Canillas
Linus Torvalds
Russell King
Masanari Iida