| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull ARM SoC late changes from Arnd Bergmann:
"These are changes that arrived a little late before the merge window
or that have multiple dependencies on previous branches so they did
not fit into one of the earlier ones. There are 10 branches merged
here, a total of 39 non-merge commits. Contents are a mixed bag for
the above reasons:
* Two new SoC platforms: ST microelectronics stixxxx and the TI
'Nspire' graphing calculator. These should have been in the 'soc'
branch but were a little late
* Support for the Exynos 5420 variant in mach-exynos, which is based
on the other exynos branches to avoid conflicts.
* Various small changes for sh-mobile, ux500 and davinci
* Common clk support for MSM"
* tag 'late-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
ARM: ux500: bail out on alien cpus
ARM: davinci: da850: adopt to pinctrl-single change for configuring multiple pins
serial: sh-sci: Initialise variables before access in sci_set_termios()
ARM: stih41x: Add B2020 board support
ARM: stih41x: Add B2000 board support
ARM: sti: Add DEBUG_LL console support
ARM: sti: Add STiH416 SOC support
ARM: sti: Add STiH415 SOC support
ARM: msm: Migrate to common clock framework
ARM: msm: Make proc_comm clock control into a platform driver
ARM: msm: Prepare clk_get() users in mach-msm for clock-pcom driver
ARM: msm: Remove clock-7x30.h include file
ARM: msm: Remove custom clk_set_{max,min}_rate() API
ARM: msm: Remove custom clk_set_flags() API
msm: iommu: Use clk_set_rate() instead of clk_set_min_rate()
msm: iommu: Convert to clk_prepare/unprepare
msm_sdcc: Convert to clk_prepare/unprepare
usb: otg: msm: Convert to clk_prepare/unprepare
msm_serial: Use devm_clk_get() and properly return errors
msm_serial: Convert to clk_prepare/unprepare
...
|
|
Pull ARM SoC driver specific changes from Arnd Bergmann:
"These changes are all driver specific and cross over between arm-soc
contents and some other subsystem, in these cases cpufreq, crypto,
dma, pinctrl, mailbox and usb, and the subsystem owners agreed to have
these changes merged through arm-soc.
As we proceed to untangle the dependencies between platform code and
driver code, the amount of changes in this category is fortunately
shrinking, for 3.11 we have 16 branches here and 101 non-merge
changesets, the majority of which are for the stedma40 dma engine
driver used in the ux500 platform. Cleaning up that code touches
multiple subsystems, but gets rid of the dependency in the end.
The mailbox code moved out from mach-omap2 to drivers/mailbox is an
intermediate step and is still omap specific at the moment. Patches
exist to generalize the subsystem and add other drivers with the same
API, but those did not make it for 3.11."
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (101 commits)
crypto: ux500: use dmaengine_submit API
crypto: ux500: use dmaengine_prep_slave_sg API
crypto: ux500: use dmaengine_device_control API
crypto: ux500/crypt: add missing __iomem qualifiers
crypto: ux500/hash: add missing static qualifiers
crypto: ux500/hash: use readl on iomem addresses
dmaengine: ste_dma40: Declare memcpy config as static
ARM: ux500: Remove mop500_snowball_ethernet_clock_enable()
ARM: ux500: Correct the EN_3v3 regulator's on/off GPIO
ARM: ux500: Provide a AB8500 GPIO Device Tree node
gpio: rcar: fix gpio_rcar_of_table
gpio-rcar: Remove #ifdef CONFIG_OF around OF-specific sections
gpio-rcar: Reference core gpio documentation in the DT bindings
clk: exynos5250: Add enum entries for divider clock of i2s1 and i2s2
ARM: dts: Update Samsung I2S documentation
ARM: dts: add clock provider information for i2s controllers in Exynos5250
ARM: dts: add Exynos audio subsystem clock controller node
clk: samsung: register audio subsystem clocks using common clock framework
ARM: dts: use #include for all device trees for Samsung
pinctrl: s3c24xx: use correct header for chained_irq functions
...
|
|
Pull ARM SoC device tree changes from Arnd Bergmann:
"These changes from 30 individual branches for the most part update
device tree files, but there are also a few source code changes that
have crept in this time, usually in order to atomically move over a
driver from using hardcoded data to DT probing.
A number of platforms change their DT files to use the C preprocessor,
which is causing a bit of churn, but that is hopefully only this once"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (372 commits)
ARM: at91: dt: rm9200ek: add spi support
ARM: at91: dt: rm9200: add spi support
ARM: at91/DT: at91sam9n12: add SPI DMA client infos
ARM: at91/DT: sama5d3: add SPI DMA client infos
ARM: at91/DT: fix SPI compatibility string
ARM: Kirkwood: Fix the internal register ranges translation
ARM: dts: bcm281xx: change comment to C89 style
ARM: mmc: bcm281xx SDHCI driver (dt mods)
ARM: nomadik: add the new clocks to the device tree
clk: nomadik: implement the Nomadik clocks properly
ARM: dts: omap5-uevm: Provide USB Host PHY clock frequency
ARM: dts: omap4-panda: Fix DVI EDID reads
ARM: dts: omap4-panda: Add USB Host support
arm: mvebu: enable mini-PCIe connectors on Armada 370 RD
ARM: shmobile: irqpin: add a DT property to enable masking on parent
ARM: dts: AM43x EPOS EVM support
ARM: dts: OMAP5: Add bandgap DT entry
ARM: dts: AM33XX: Add pinmux configuration for CPSW to am335x EVM
ARM: dts: AM33XX: Add pinmux configuration for CPSW to EVMsk
ARM: dts: AM33XX: Add pinmux configuration for CPSW to beaglebone
...
|
|
This makes the l2x0 initialization fail gracefully on non-ux500
systems.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Patches from Lee Jones:
This gets rid of mop500_snowball_ethernet_clock_enable() which is no
longer in use. It also straightens out a bug which ensures the SMSC911x's
regulator is turned on at start-up when using Device Tree.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
mop500_snowball_ethernet_clock_enable() provided a means to enable a
clock which was used for the SMSC911x Ethernet device on Snowball. It
was merely a stand-in until the driver was common clk compliant. Now
that it is, this can be removed for both DT and ATAGs booting.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
From Tony Lindgren:
Minor board changes for v3.11 merge window. These are
tapering down finally as we're getting closer to making
omap2+ DT only.
* tag 'omap-for-v3.11/board-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: omap2plus_defconfig: enable USB_PHY and NOP_USB_XCEIV
ARM: OMAP1: nokia770: enable Tahvo
ARM: OMAP3EVM: Marking omap3_evm_display_init() with CONFIG_BROKEN
arm: omap: board-overo: reset GPIO for SMSC911x
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Removes the following warnings:
arch/arm/mach-ux500/board-mop500-pins.c:51:6: warning: 'slpm_in_nopull_wkup' defined but not used [-Wunused-variable]
arch/arm/mach-ux500/board-mop500-pins.c:63:6: warning: 'slpm_out_lo_wkup' defined but not used [-Wunused-variable]
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Linus Walleij <linux.walleij@linaro.org>
|
|
From Linus Walleij:
Device tree patches for ux500, basically trees and auxdata:
- Fix for the thermal node to be contained in the PRCMU node
- Add the DTS and auxdata needed to boot the U8540 platform
- Various regulators added and renamed
- Rename base SoC node
- A bunch of DMA patches adding channels for DT boots
- A bunch of crypto+hash patches adding config for DT boots
- A bunch of patches fixing the ALSA SoC support to work
- Register the LP5521 LEDs
- Fix a number of typos and naming errors
* tag 'ux500-dt-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: (39 commits)
ARM: ux500: drop any 0x prefix from I2C DT devices
ARM: ux500: Allocate correct amount of memory for the u8540 in DT
ARM: ux500: Provide auxdata to ux500 ASoC driver
ARM: ux500: Add DT regulators for ab8500-codec
ARM: ux500: Correct anamic2 typo in DT files
ARM: ux500: Fix trivial typo in v-anamic1 comment
ARM: ux500: Reduce PRCMU reg-names to shorter form for u8540 DT
ARM: ux500: Add an auxdata entry for MUSB for clock-name look-up
ARM: ux500: cut chip-select GPIOs from SSP device
ARM: ux500: use symbolic names for interrupt flags
ARM: ux500: use #include syntax to include *.dtsi.
ARM: ux500: bump MMC/SD max frequency for DT boots
ARM: ux500: Apply other compatible name to the u8540 DTS file
pinctrl/nomadik: Standardise Pinctrl compat string for DBx5x based platforms
ARM: ux500: Standardise Pinctrl compatible string for DBx5x based platforms
ARM: ux500: Standardise DBx5x0 based Pinctrl compat string in the DTS
crypto: ux500/hash - Enable DT probing of the driver
crypto: ux500/cryp - Enable DT probing of the driver
ARM: ux500: enable the crypto and hash on all dbx500
ARM: ux500: Provide an AUXDATA entry for ux500-hash
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
From Linus Walleij:
Second set of DMA40 changes: refactorings and device tree
support for the DMA40. Now with MUSB and some platform
data removal.
* tag 'ux500-dma40-for-arm-soc-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
dmaengine: ste_dma40: Fetch disabled channels from DT
dmaengine: ste_dma40: Fetch the number of physical channels from DT
ARM: ux500: Stop passing DMA platform data though AUXDATA
dmaengine: ste_dma40: Allow memcpy channels to be configured from DT
dmaengine: ste_dma40_ll: Replace meaningless register set with comment
dmaengine: ste_dma40: Convert data_width from register bit format to value
dmaengine: ste_dma40_ll: Use the BIT macro to replace ugly '(1 << x)'s
ARM: ux500: Remove recently unused stedma40_xfer_dir enums
dmaengine: ste_dma40: Replace ST-E's home-brew DMA direction defs with generic ones
ARM: ux500: Replace ST-E's home-brew DMA direction definition with the generic one
dmaengine: ste_dma40: Use the BIT macro to replace ugly '(1 << x)'s
ARM: ux500: Remove empty function u8500_of_init_devices()
ARM: ux500: Remove ux500-musb platform registation when booting with DT
usb: musb: ux500: add device tree probing support
usb: musb: ux500: attempt to find channels by name before using pdata
usb: musb: ux500: harden checks for platform data
usb: musb: ux500: take the dma_mask from coherent_dma_mask
usb: musb: ux500: move the MUSB HDRC configuration into the driver
usb: musb: ux500: move channel number knowledge into the driver
|
|
From Linus Walleij:
Ux500 pinctrl changes:
- Updates to MSP pinctrl entry for ALSA SoC
- ABx500 pinctrl tables
* tag 'ux500-pinctrl-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: add ABx500 pinctrl tables
ARM: ux500: update MSP1 pinctrl defintions
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
From Kukjin Kim, driver updats for s3c24xx:
- move cpufreq driver into drivers/
- add pinctrl-s3c24xx driver
- cleanup OF in gpio driver
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
phys_addr_t may be 64 bit, which causes this harmless warning
in ux500_read_asicid:
arch/arm/mach-ux500/id.c: In function 'ux500_read_asicid':
arch/arm/include/asm/io.h:159:19: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
#define IOMEM(x) ((void __force __iomem *)(x))
^
arch/arm/mach-ux500/id.c:40:9: note: in expansion of macro 'readl'
return readl(IOMEM(UX500_VIRT_ROM + (addr & 0xfff)));
We can solve this in a nicer way by making UX500_VIRT_ROM have a proper
type to start with and calculating the address using pointer arithmetic.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The DMA platform data is now empty due to some recent refactoring,
so there is no longer a requirement to pass it though.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
STEDMA40_*_TO_* direction definitions are identical in all but name to
the pre-defined generic DMA_*_TO_* ones. Let's make things easy by not
duplicating such things.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
As promised, now all devices which resided in u8500_of_init_devices()
have been enabled for Device Tree, we can completely remove it.
Acked-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Now the ux500-musb driver has been enabled for Device Tree, there is no
requirement to register it from platform code.
Acked-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The dma_mask will always be the same as the coherent_dma_mask, so let's
cut down on the platform_data burden and set it as such in the driver.
This also saves us from supporting it separately when we come to enable
this driver for Device Tree.
Cc: linux-usb@vger.kernel.org
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The MUSB HDRC configuration never changes between each of the ux500
supported platforms, so there's little point passing it though platform
data. If we set it in the driver instead, we can make good use of it
when booting with either ATAGs or Device Tree.
Cc: linux-usb@vger.kernel.org
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
For all ux500 based platforms the maximum number of end-points are used.
Move this knowledge into the driver so we can relinquish the burden from
platform data. This also removes quite a bit of complexity from the driver
and will aid us when we come to enable the driver for Device Tree.
Cc: linux-usb@vger.kernel.org
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Ux500 ASoC driver is expected to have a specific device name to get
clock resources correctly. This patch provides the necessary
OF_DEV_AUXDATA to match the name in DT and non-DT cases.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds pin control tables for the ABx500 (AB8500 and
AB8505) PMIC, which also happens to act as a multimedia
pin expander on the ux500 platforms.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The recently DT:ed MUSB driver will require clock-name by device-name
look-up capability, until common clk has is properly supported by the
ux500 platform.
Acked-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
From Linus Walleij:
This is a set of patches from Lee Jones to start converting
the ux500 to fetch DMA channels from the device tree:
- Full DT support and channel mapping in the DMA40 driver
- Dropping of platform data for migrated devices on the DT
boot path.
* tag 'ux500-dma40-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: (36 commits)
ARM: ux500: Register Cryp and Hash platform drivers on Snowball
crypto: ux500/[cryp|hash] - Show successful start-up in the bootlog
ARM: ux500: Stop passing Cryp DMA channel config information though pdata
crypto: ux500/cryp - Set DMA configuration though dma_slave_config()
crypto: ux500/cryp - Prepare clock before enabling it
ARM: ux500: Stop passing Hash DMA channel config information though pdata
crypto: ux500/hash - Set DMA configuration though dma_slave_config()
crypto: ux500/hash - Prepare clock before enabling it
ARM: ux500: Remove unnecessary attributes from DMA channel request pdata
dmaengine: ste_dma40: Correct copy/paste error
ARM: ux500: Remove DMA address look-up table
dmaengine: ste_dma40: Remove redundant address fetching function
dmaengine: ste_dma40: Only use addresses passed as configuration information
ARM: ux500: Stop passing UART's platform data for Device Tree boots
dmaengine: ste_dma40: Don't configure runtime configurable setup during allocate
dmaengine: ste_dma40: Remove unnecessary call to d40_phy_cfg()
dmaengine: ste_dma40: Separate Logical Global Interrupt Mask (GIM) unmasking
ARM: ux500: Pass remnant platform data though to DMA40 driver
dmaengine: ste_dma40: Supply full Device Tree parsing support
dmaengine: ste_dma40: Allow driver to be probe()able when DT is enabled
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Update MSP1 pinctrl definitions in mop500_family_pinmap by removing
sleep state and setting default ones as pin hogs, as those are used by
both ux500-msp-i2s.1 and ux500-msp-i2s.3.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch fixes a bug introduced in the v3.10 merge window.
The AB8500 External Regulator driver has recently landed upstream,
which registers each of the 3 external regulators located on the
AB8500. If these regulators are marked as 'always on', there is a
potential for power-loss. If they're not and are seemingly unused
the Regulator subsystem will attempt to disable them to save power.
This causes an issue for AUX1, AUX2 and AUX3 as they obtain their
power from EXT3. So we're specifying that here to prevent EXT3 from
being powered down.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Multiplatform calls all enabled platforms' initcalls. In the
ux500_idle_init() initcall we call into the DBx500-PRCMU which in turn
executes some ux500 specific register reads/writes. When running on
some !ux500 platforms this ends up causing a kernel Oops. This patch
ensures the PRCMU call is only invoked when running on ux500 based
platforms.
Reported-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This provides a device name which is required by the common clk API.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This provides a device name which is required by the common clk API.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[Edited patch subject]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
If we attempt to use the existing u8500 of_dev_auxdata struct to boot
the u8540, we fail to obtain a console, due to a lack of DMA support
on the platform.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch removes a comment which explains that the ab8505 platform
uses the same initialisation settings as the ab8500. Well when this
changed and the ab8505 started using its own set of initialisation
values, someone forgot to remove it.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
By setting the host capabilities MMC_CAP_UHS_SDR12|25 for
the SD card device we enable support for UHS cards. The
supported mode is SDR12 and SDR25.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
For several reasons, the mmc protocol layer expects devices
being non-removable to use MMC_CAP_NONREMOVABLE, so then we
adapt to this expectation.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
By enabling MMC_CAP_ERASE for the SD/MMC devices the mmc block
layer will now act on DISCARD requests.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
By adding MMC_CAP_CMD23 for the eMMC devices, we can support RPMB
and Reliable Write. Additionally it will mean CMD12 will not be sent
to end a successful data transfer.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The mmci host driver overrides platform ocr mask when a vmmc regulator
can be used. This is the case for sdi0(SD-card) and for sdi4(eMMC).
Thus it is pointless of specifing these mask and why we do remove them.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
We are able to cope with an SDMMC clock of 100MHz so let's
make use of the full frequency instead of the half.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Tightly Coupled Data Memory for the DB9540 is actually in the
same place as the DB8500's. This definition is just plain wrong.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Tightly Coupled Program Memory location is actually 32kB in
size, rather than the originally depicted 4kB.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
These drivers are now operational and even use the latest common clk
and DMA APIs. There's no reason why we shouldn't start them up now.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
DMA channel configuration information should be setup in the driver.
The Ux500 Cryp driver now does this, so there's no need to send it
though here too.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
DMA channel configuration information should be setup in the driver.
The Ux500 Hash driver now does this, so there's no need to send it
though here too.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
DMA data width and packet size information is only required at channel
configuration time. Any information passed from platform data is passed
directly to the DMA40 driver to use during channel allocation, but these
pieces of information are subsequently ignored by the driver, so we may
as well remove them.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
DMA addresses are now passed as part of the dmaengine API by invoking
dmaengine_slave_config(). So there's no requirement for the DMA40
driver to look them up in a table provided by platform data. This
method does not fit in well using Device Tree either.
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
It was required to pass DMA channel configuration information to the
UART driver before the new DMA API was in place. Now that it is, and
is fully compatible with Device Tree we can stop doing that.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Ironically, in order to remove lots of the auxdata assignments, we have
to add just one more. A lot of them require DMA information to be passed
into clients for DMA channel allocation, but we now have this capability
in Device Tree. However, the DMA40 driver still relies on a reverse table
look-up to obtain DMA addresses. Until all of the clients are converted,
over to the new API, we're stuck with this.
Also, now the DMA40 has been DT:ed, there's no requirement to register
it using traditional methods, so let's remove it.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This change will cost ~25KB of memory, but it's worth the trade-off,
as it removes a great deal of overhead. It means that instead of only
allocating memory for the logical channels in use, it does so for all
available ones, which is 32 per physical channel. However, this now
means we can remove some platform data and we don't have to worry
about adding vendor specific variables to Device Tree.
Acked-by: Vinod Koul <vnod.koul@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
'psize' is used to calculate the maximum DMA burst size. However it
is only taken into consideration when editing the DMA channel's
configuration. The Audio DMA platform data is only used to allocate
a channel, not configure it. That will be done at a later date within
the MSP driver.
We're also removing comments which are no longer required, as
'data_width' is no longer set in any device's platform data period.
Tested-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
DMA configuration data is now allocated in the UART driver, so these
are just ignored.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
Linus Torvalds
Linus Walleij
Arnd Bergmann
Lee Jones
Olof Johansson
Fabio Baltieri
Patrice Chotard
Ulf Hansson