| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The node names should be generic and DT schema expects certain pattern
(e.g. with key/button/switch).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Remove the unnecessary cpu_alert0 and cpu_crit0 TMU node overrides as
these are added dynamically by boot firmware based on CPU temperature
grade.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Define the missing clock-names property for the pcie_phy required by
the fsl,imx8-pcie-phy dt bindings.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add the missing 'uart-has-rtscts' property to UART's that have hardware
flow control capability.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add gpio-line-names for the various GPIO's used on Gateworks Venice
boards. Note that these GPIO's are typically 'configured' in Boot
Firmware via gpio-hog therefore we only configure line names to keep the
boot firmware configuration from changing on kernel init.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add PCIe support to GW71xx/GW72xx/GW73xx/GW7901/GW7902
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Since commit b21269b12e48 ("arm64: dts: imx8mm: add GPC node") the
GW7901 will hang during kernel init because it does not power the unused
GPU voltage rails on the IMX8MM. Disable pgc_gpumix to work around this.
We also disable the GPU devices that depend on the gpumix power domain
and pgc_gpu to avoid them staying in a probe deferred state forever.
Additionally as the MIPI voltage rail is also not connected on this
board we disable pgc_mipi and disp_blk_ctrl.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable internal pull-down on UART transceiver GPIO config pins.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The USB hub has it's reset as GPIO4_IO17 but can be sub-loaded and
VBUS provided by a VBUS regulator with GPIO4_IO2 as the enable and
GPIO1_IO15 as the active-low over-current.
Enable pull-up for GPIO4_IO17 to keep hub out of reset and move VBUS
enable to GPIO4_IO2. Additionally enable pull-up on GPIO1_IO15 so that
if the hub is loaded it never over-currents.
This allows USB to work in both configurations without a device-tree
change.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The following dtc build warning is seen with W=1:
arch/arm64/boot/dts/freescale/imx8mm-venice-gw7901.dts:291.14-397.4: Warning (avoid_unnecessary_addr_size): /soc@0/bus@30800000/i2c@30a20000/gsc@20: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Remove the unnecessary #address-cells/#size-cells to fix it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-By: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Gateworks GW7901 is an ARM based single board computer (SBC)
featuring:
- i.MX8M Mini SoC
- LPDDR4 DRAM
- eMMC FLASH
- SPI FRAM
- Gateworks System Controller (GSC)
- Atmel ATECC Crypto Authentication
- USB 2.0
- Microchip GbE Switch
- Multiple multi-protocol RS232/RS485/RS422 Serial ports
- onboard 802.11ac WiFi / BT
- microSD socket
- miniPCIe socket with PCIe, USB 2.0 and dual SIM sockets
- Wide range DC power input
- 802.3at PoE
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
Krzysztof Kozlowski
Tim Harvey
Fabio Estevam