| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull ARM SoC fixes from Arnd Bergmann:
"There are a number of DT fixes, mostly for mistakes found through
static checking of the dts files again, as well as a couple of minor
changes to address incorrect DT settings.
For i.MX, there is yet another series of devitree changes to update
RGMII delay settings for ethernet, which is an ongoing problem after
some driver changes.
For SoC specific device drivers, a number of smaller fixes came up:
- i.MX SoC identification was incorrectly registered non-i.MX
machines when the driver is built-in
- One fix on imx8m-blk-ctrl driver to get i.MX8MM MIPI reset work
properly
- a few compile fixes for warnings that get in the way of -Werror
- a string overflow in the scpi firmware driver
- a boot failure with FORTIFY_SOURCE on Rockchips machines
- broken error handling in the AMD TEE driver
- a revert for a tegra reset driver commit that broke HDA"
* tag 'soc-fixes-5.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (25 commits)
soc/tegra: fuse: Fix bitwise vs. logical OR warning
firmware: arm_scpi: Fix string overflow in SCPI genpd driver
soc: imx: Register SoC device only on i.MX boards
soc: imx: imx8m-blk-ctrl: Fix imx8mm mipi reset
ARM: dts: imx6ull-pinfunc: Fix CSI_DATA07__ESAI_TX0 pad name
arm64: dts: imx8mq: remove interconnect property from lcdif
ARM: socfpga: dts: fix qspi node compatible
arm64: dts: apple: add #interrupt-cells property to pinctrl nodes
dt-bindings: i2c: apple,i2c: allow multiple compatibles
arm64: meson: remove COMMON_CLK
arm64: meson: fix dts for JetHub D1
tee: amdtee: fix an IS_ERR() vs NULL bug
arm64: dts: apple: change ethernet0 device type to ethernet
arm64: dts: ten64: remove redundant interrupt declaration for gpio-keys
arm64: dts: rockchip: fix poweroff on helios64
arm64: dts: rockchip: fix audio-supply for Rock Pi 4
arm64: dts: rockchip: fix rk3399-leez-p710 vcc3v3-lan supply
arm64: dts: rockchip: fix rk3308-roc-cc vcc-sd supply
arm64: dts: rockchip: remove mmc-hs400-enhanced-strobe from rk3399-khadas-edge
ARM: rockchip: Use memcpy_toio instead of memcpy on smp bring-up
...
|
|
Use the interconnects property to hook up the MMC and BPMP to the memory
controller. This is needed to set the correct bus-level DMA mask, which
is a prerequisite for adding IOMMU support.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This adds the memory controller and the embedded external memory
controller found on the Tegra234 SoC.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add the missing EMC general interrupt for the external memory controller
on Tegra194.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add required device-tree properties to populate all speed
modes supported by SDMMC4 instance of Tegra194 SDHCI controller.
Signed-off-by: Prathamesh Shete <pshete@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
DMA operations for the Tegra194 Video Image Compositor (VIC) are
coherent and so populate the 'dma-coherent' property.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Name the Ethernet PHY device tree nodes as expected by the DT schema.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The only-1-8-v property is not support by an DT schema, so drop it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Make the order of the clocks and clock-names properties match the order
in the device tree bindings. This isn't strictly necessary from a point
of view of the operating system because matching will be done based on
the clock-names, but it makes it easier to validate the device trees
against the DT schema.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add missing interrupts, clocks, clock-names, reset and reset-names
properties for the TSEC blocks found on Tegra210.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The XUSB pad controller handles the various PLL power supplies, so
remove any references to them from the PCIe and XUSB controller device
tree nodes.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The XUSB pad controller handles the various PLL power supplies, so
remove any references to them from the XUSB controller device tree
node.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The XUSB pad controller handles the various PLL power supplies, so
remove any references to them from the PCIe and XUSB controller device
tree nodes.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
GPIO hog nodes must have a "hog-" prefix or "-hog" suffix according to
the DT schema. Rename all such nodes to allow validation to pass.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Remove the unsupported "regulator-disable-ramp-delay" properties which
ended up in various DTS files for some reason.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The TCU is basically a serial port (albeit a fancy one), so it should be
named "serial".
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The "core_m" clock is not documented in the Tegra194 PCIe device tree
bindings, so remove it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The num-viewport property is never used and can be dropped, whereas the
"iommus" property is not needed since we use "iommu-map-mask" and
"iommu-map" already.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The HSP instances on Tegra194 are not fully compatible with the version
found on Tegra186, so drop the fallback compatible string from the list.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The Tegra194 pinmux DT bindings do not define the nvidia,lpdr property,
so drop them from the device trees that have listed them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The standard "jedec," vendor prefix should be used for SPI NOR flash
chips. This allows the right DT schema to be picked for validation.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Audio graph endpoints don't have a "reg" property, so they shouldn't
have a unit-address either.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The Tegra186 CCPLEX cluster register region is 4 MiB is length, not 4
MiB - 1. This was likely presumed to be the "limit" rather than length.
Fix it up.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The I2C controller found on Tegra186 is not fully compatible with the
Tegra210 version, so drop the fallback compatible string from the list.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Child nodes of the TI INA3221 power monitor device tree node should be
called input@* according to the DT schema.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The DT schema requires that nodes representing thermal zones include a
"-thermal" suffix in their name.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Make the order of the clocks and clock-names properties match the order
in the device tree bindings. This isn't strictly necessary from a point
of view of the operating system because matching will be done based on
the clock-names, but it makes it easier to validate the device trees
against the DT schema.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The CML1 and PLL_E clocks are never explicitly used by the AHCI
controller found on Tegra132, so drop them from the corresponding device
tree node.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The I2C controller found on Tegra124 is not fully compatible with the
Tegra114 version, so drop the fallback compatible string from the list.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add peripheral OPP tables on Tegra132 and wire them up to ACTMON and the
EMC. While at it, add the missing "#interconnect-cells" properties to
the memory controller and external memory controller nodes. Also set the
"#reset-cells" property for the memory controller because it exports the
hotflush reset controls.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The TKE (time-keeping engine) found on Tegra132 is not backwards
compatible with the version found on Tegra20, so update the compatible
string list accordingly.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The Tegra PMC device tree bindings don't support the "#wake-cells" and
"nvidia,reset-gpio" properties, so remove them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The AS3722 pinmux device tree node doesn't have a "reg" property and
therefore must not have a unit-address, so drop it.
While at it, add missing unit-addresses for the charger and smart
battery IC's on the ChromeOS embedded controller's I2C tunnel bus.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The native timers IP block found on NVIDIA Tegra SoCs implements a
watchdog timer that can be used to recover from system hangs. Add the
device tree node on Tegra186.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Regulators defined at the top level in device tree are no longer part of
a simple bus and therefore don't have a reg property. Nodes without a
reg property shouldn't have a unit-address either, so drop the unit
address from the node names. To ensure nodes aren't duplicated (in which
case they would end up merged in the final DTB), append the name of the
regulator to the node name.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Clocks defined at the top level in device tree are no longer part of a
simple bus and therefore don't have a reg property. Nodes without a reg
property shouldn't have a unit-address either, so drop the unit address
from the node names. To ensure nodes aren't duplicated (in which case
they would end up merged in the final DTB), append the name of the clock
to the node name.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The display controllers are attached to a separate ARM SMMU instance
that is dedicated to servicing isochronous memory clients. Add this ISO
instance of the ARM SMMU to device tree.
Please note that the display controllers are not hooked up to this SMMU
yet, because we are still missing a means to transition framebuffers
used by the bootloader to the kernel.
This based upon an initial patch by Thierry Reding <treding@nvidia.com>.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Populate the device-tree nodes for NVENC and NVJPG Host1x engines on
Tegra186 and Tegra194.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add support to enumerate SD in UHS mode on Tegra194. Add required
device-tree properties in SDMMC1 and SDMMC3 instances to enable dynamic
pad voltage switching and enumerate SD card in UHS-I modes.
Signed-off-by: Prathamesh Shete <pshete@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The Jetson AGX Orin Developer Kit is a continuation of the Jetson
Developer Kit line using the new NVIDIA Tegra234 (Orin) SoC.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The NVIDIA Tegra234 SoC has 3 clusters of 4 Cortex-A78AE CPU cores each,
for a total of 12 CPUs. Each CPU has 64 KiB instruction and data caches
with each cluster having an additional 256 KiB unified L2 cache and a 2
MiB L3 cache.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
These two controllers expose general purpose I/O pins that can be used
to control or monitor a variety of signals.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add a device for TCU (Tegra Combined UART) used for serial console.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add missing properties to the eMMC controller, as required to use it on
actual hardware.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
On final Tegra234 systems, shared memory for communication with BPMP is
located at offset 0x70000 in SYSRAM.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The RTC device requires a clock. Add it.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The json-schema bindings for SRAM expect the nodes to be called "sram"
rather than "sysram" or "shmem". Furthermore, place the brackets around
the SYSRAM references such that a two-element array is created rather
than a two-element array nested in a single-element array. This is not
relevant for device tree itself, but allows the nodes to be properly
validated against json-schema bindings.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add vdd core regulator (1.1 V).
This patch add regulator support for gpu.
The H/W manual mentions nothing about a gpu regulator. So using vdd
core regulator for gpu.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211208104026.421-4-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add Mali-G31 GPU node to SoC DTSI.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211208104026.421-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
SoCFPGA dts updates for v5.17
- Update N5X to include qspi, usb and ethernet
- Adjust NAND partition size for Agilex and Stratix10
* tag 'socfpga_dts_update_for_v5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
arm64: dts: Update NAND MTD partition for Agilex and Stratix 10
arm64: dts: n5x: add qspi, usb, and ethernet support
Link: https://lore.kernel.org/r/20211215164545.300273-1-dinguyen@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
Linus Torvalds
Thierry Reding
Prathamesh Shete
Jon Hunter
Mikko Perttunen
Biju Das
Arnd Bergmann