| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Commit 4fdbfd60a3a2 ("arm64: tegra: Add PCIe slot supply information
in p2972-0000 platform") added regulators for the PCIe slot on the
Jetson Xavier platform. One of these regulators has an active-low enable
and this commit incorrectly added an active-low specifier for the GPIO
which causes the following warning to occur on boot ...
WARNING KERN regulator@3 GPIO handle specifies active low - ignored
The fixed-regulator binding does not use the active-low flag from the
gpio specifier and purely relies of the presence of the
'enable-active-high' property to determine if it is active high or low
(if this property is omitted). Fix this warning by setting the GPIO
to active-high in the GPIO specifier. Finally, remove the
'enable-active-low' as this is not a valid property.
Fixes: 4fdbfd60a3a2 ("arm64: tegra: Add PCIe slot supply information in p2972-0000 platform")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Commit 34993594181d ("arm64: tegra: Enable HDMI on Jetson TX1")
added a regulator for HDMI on the Jetson TX1 platform. This regulator
has an active high enable, but the GPIO specifier for enabling the
regulator incorrectly defines it as active-low. This causes the
following warning to occur on boot ...
WARNING KERN regulator@10 GPIO handle specifies active low - ignored
The fixed-regulator binding does not use the active-low flag from the
gpio specifier and purely relies of the presence of the
'enable-active-high' property to determine if it is active high or low
(if this property is omitted). Fix this warning by setting the GPIO
to active-high in the GPIO specifier which aligns with the presense of
the 'enable-active-high' property.
Fixes: 34993594181d ("arm64: tegra: Enable HDMI on Jetson TX1")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
With the introduction of 'cce360b54ce6 ("arm64: capabilities: Filter the
entries based on a given mask")' the Qualcomm Falkor/Kryo errata 1003 is
no long applied.
The result of not applying errata 1003 is that MSM8996 runs into various
RCU stalls and fails to boot most of the times.
Give 1003 a "type" to ensure they are not filtered out in
update_cpu_capabilities().
Fixes: cce360b54ce6 ("arm64: capabilities: Filter the entries based on a given mask")
Cc: stable@vger.kernel.org
Reported-by: Mark Brown <broonie@kernel.org>
Suggested-by: Will Deacon <will@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Shared and writable mappings (__S.1.) should be clean (!dirty) initially
and made dirty on a subsequent write either through the hardware DBM
(dirty bit management) mechanism or through a write page fault. A clean
pte for the arm64 kernel is one that has PTE_RDONLY set and PTE_DIRTY
clear.
The PAGE_SHARED{,_EXEC} attributes have PTE_WRITE set (PTE_DBM) and
PTE_DIRTY clear. Prior to commit 73e86cb03cf2 ("arm64: Move PTE_RDONLY
bit handling out of set_pte_at()"), it was the responsibility of
set_pte_at() to set the PTE_RDONLY bit and mark the pte clean if the
software PTE_DIRTY bit was not set. However, the above commit removed
the pte_sw_dirty() check and the subsequent setting of PTE_RDONLY in
set_pte_at() while leaving the PAGE_SHARED{,_EXEC} definitions
unchanged. The result is that shared+writable mappings are now dirty by
default
Fix the above by explicitly setting PTE_RDONLY in PAGE_SHARED{,_EXEC}.
In addition, remove the superfluous PTE_DIRTY bit from the kernel PROT_*
attributes.
Fixes: 73e86cb03cf2 ("arm64: Move PTE_RDONLY bit handling out of set_pte_at()")
Cc: <stable@vger.kernel.org> # 4.14.x-
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
When attempting to executing non-executable memory, the fault message
shows:
Unable to handle kernel read from unreadable memory at virtual address
ffff802dac469000
This may confuse someone, so add a new fault message for instruction
abort.
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Xiang Zheng <zhengxiang9@huawei.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Associate the UART nodes with the corresponding reset controller bits.
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
Add nodes for the Realtek RTD1295 reset controllers.
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
Add the watchdog node to the RTD129x Device Tree.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
[AF: Moved from RTD1295 to new RTD129x]
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
Add 27 MHz oscillator clock node.
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
Add Device Trees for RTD1296 SoC and Synology DiskStation DS418.
Cc: info@synology.com
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
Add Device Trees for RTD1293 SoC and Synology DiskStation DS418j NAS.
Cc: info@synology.com
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
Move the SPDX-License-Identifier to the top line and update to SPDX 2.0.
While at it, switch from GPLv2+/MIT to GPLv2+/BSD2c before adding more.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
Enable support for the S32V234 SoC, including the previously added UART
driver.
Signed-off-by: Mihaela Martinas <Mihaela.Martinas@freescale.com>
Signed-off-by: Adrian.Nitu <adrian.nitu@freescale.com>
Signed-off-by: Stoica Cosmin-Stefan <cosmin.stoica@nxp.com>
Signed-off-by: Stefan-Gabriel Mirea <stefan-gabriel.mirea@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Select CONFIG_KEYBOARD_IMX_SC_KEY as module by default to
support i.MX8QXP scu key driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Move the synchronous exception paths from entry.S into a C file to
improve the code readability.
* for-next/entry-s-to-c:
arm64: entry-common: don't touch daif before bp-hardening
arm64: Remove asmlinkage from updated functions
arm64: entry: convert el0_sync to C
arm64: entry: convert el1_sync to C
arm64: add local_daif_inherit()
arm64: Add prototypes for functions called by entry.S
arm64: remove __exception annotations
|
|
This variable is only used in the arch/arm64/mm/init.c file for
ZONE_DMA32 initialisation, no need to expose it.
Reported-by: Will Deacon <will@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Similarly to erratum 1165522 that affects Cortex-A76, A57 and A72
respectively suffer from errata 1319537 and 1319367, potentially
resulting in TLB corruption if the CPU speculates an AT instruction
while switching guests.
The fix is slightly more involved since we don't have VHE to help us
here, but the idea is the same: when switching a guest in, we must
prevent any speculated AT from being able to parse the page tables
until S2 is up and running. Only at this stage can we allow AT to take
place.
For this, we always restore the guest sysregs first, except for its
SCTLR and TCR registers, which must be set with SCTLR.M=1 and
TCR.EPD{0,1} = {1, 1}, effectively disabling the PTW and TLB
allocation. Once S2 is setup, we restore the guest's SCTLR and
TCR. Similar things must be done on TLB invalidation...
* 'kvm-arm64/erratum-1319367' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms:
arm64: Enable and document ARM errata 1319367 and 1319537
arm64: KVM: Prevent speculative S1 PTW when restoring vcpu context
arm64: KVM: Disable EL1 PTW when invalidating S2 TLBs
arm64: KVM: Reorder system register restoration and stage-2 activation
arm64: Add ARM64_WORKAROUND_1319367 for all A57 and A72 versions
|
|
On CPUs that support S2FWB (Armv8.4+), KVM configures the stage 2 page
tables to override the memory attributes of memory accesses, regardless
of the stage 1 page table configurations, and also when the stage 1 MMU
is turned off. This results in all memory accesses to RAM being
cacheable, including during early boot of the guest.
On CPUs without this feature, memory accesses were non-cacheable during
boot until the guest turned on the stage 1 MMU, and we had to detect
when the guest turned on the MMU, such that we could invalidate all cache
entries and ensure a consistent view of memory with the MMU turned on.
When the guest turned on the caches, we would call stage2_flush_vm()
from kvm_toggle_cache().
However, stage2_flush_vm() walks all the stage 2 tables, and calls
__kvm_flush-dcache_pte, which on a system with S2FWB does ... absolutely
nothing.
We can avoid that whole song and dance, and simply not set TVM when
creating a VM on a system that has S2FWB.
Signed-off-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20191028130541.30536-1-christoffer.dall@arm.com
|
|
Neoverse-N1 cores with the 'COHERENT_ICACHE' feature may fetch stale
instructions when software depends on prefetch-speculation-protection
instead of explicit synchronization. [0]
The workaround is to trap I-Cache maintenance and issue an
inner-shareable TLBI. The affected cores have a Coherent I-Cache, so the
I-Cache maintenance isn't necessary. The core tells user-space it can
skip it with CTR_EL0.DIC. We also have to trap this register to hide the
bit forcing DIC-aware user-space to perform the maintenance.
To avoid trapping all cache-maintenance, this workaround depends on
a firmware component that only traps I-cache maintenance from EL0 and
performs the workaround.
For user-space, the kernel's work is to trap CTR_EL0 to hide DIC, and
produce a fake IminLine. EL3 traps the now-necessary I-Cache maintenance
and performs the inner-shareable-TLBI that makes everything better.
[0] https://developer.arm.com/docs/sden885747/latest/arm-neoverse-n1-mp050-software-developer-errata-notice
* for-next/neoverse-n1-stale-instr:
arm64: Silence clang warning on mismatched value/register sizes
arm64: compat: Workaround Neoverse-N1 #1542419 for compat user-space
arm64: Fake the IminLine size on systems affected by Neoverse-N1 #1542419
arm64: errata: Hide CTR_EL0.DIC on systems affected by Neoverse-N1 #1542419
|
|
ARMv8 Juno update for v5.5
Single patch to add support for Mali GPU on all versions of Juno.
Though it's disabled by default, it is very useful to test panfrost
drivers.
* tag 'juno-update-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: juno: add GPU subsystem
Link: https://lore.kernel.org/r/20191028040022.GC20568@e107533-lin.cambridge.arm.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This is required to solve the conflicts with subsequent merges of two
more errata workaround branches.
* arm64/for-next/fixes:
arm64: tags: Preserve tags for addresses translated via TTBR1
arm64: mm: fix inverted PAR_EL1.F check
arm64: sysreg: fix incorrect definition of SYS_PAR_EL1_F
arm64: entry.S: Do not preempt from IRQ before all cpufeatures are enabled
arm64: hibernate: check pgd table allocation
arm64: cpufeature: Treat ID_AA64ZFR0_EL1 as RAZ when SVE is not enabled
arm64: Fix kcore macros after 52-bit virtual addressing fallout
arm64: Allow CAVIUM_TX2_ERRATUM_219 to be selected
arm64: Avoid Cavium TX2 erratum 219 when switching TTBR
arm64: Enable workaround for Cavium TX2 erratum 219 when running SMT
arm64: KVM: Trap VM ops when ARM64_WORKAROUND_CAVIUM_TX2_219_TVM is set
|
|
ARM/ARM64 has counters halt_successful_poll, halt_attempted_poll,
halt_poll_invalid, and halt_wakeup but never exposed those in debugfs.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1572164390-5851-1-git-send-email-borntraeger@de.ibm.com
|
|
i.MX8MN LPDDR4 EVK board shares most of the device as DDR4 EVK board,
the ONLY difference are the DDR type and PMIC, add support for it
and make it default i.MX8MN EVK board as usual.
The PMIC driver is NOT ready, so cpu-freq needs to be disabled as
it depends on regulator provided by PMIC.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
i.MX8MN has different EVK boards to support different DDR types,
the ONLY differences are DDR chips and PMIC, so most of the devices
can be shared between these EVK boards, create a EVK dtsi file for
common use.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
usdhc's clock rate is different according to different devices
connected, so clock rate assignment should be placed in board
DT according to different devices connected on each usdhc port.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
usdhc's clock rate is different according to different devices
connected, so clock rate assignment should be placed in board
DT according to different devices connected on each usdhc port.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
usdhc's clock rate is different according to different devices
connected, so clock rate assignment should be placed in board
DT according to different devices connected on each usdhc port.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
usdhc's clock rate is different according to different devices
connected, so clock rate assignment should be placed in board
DT according to different devices connected on each usdhc port.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add initial version of device tree for S32V234-EVB, including nodes for the
4 Cortex-A53 cores, AIPS bus with UART modules, ARM architected timer and
Generic Interrupt Controller (GIC).
Keep SoC level separate from board level to let future boards with this SoC
share common properties, while the dts files will keep board-dependent
properties.
Signed-off-by: Stoica Cosmin-Stefan <cosmin.stoica@nxp.com>
Signed-off-by: Mihaela Martinas <Mihaela.Martinas@freescale.com>
Signed-off-by: Dan Nica <dan.nica@nxp.com>
Signed-off-by: Larisa Grigore <Larisa.Grigore@nxp.com>
Signed-off-by: Phu Luu An <phu.luuan@nxp.com>
Signed-off-by: Stefan-Gabriel Mirea <stefan-gabriel.mirea@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Assign clocks and clock-rates for audio plls, that audio
drivers can utilize them.
Add dai-tdm-slot-num and dai-tdm-slot-width for sound-wm8524,
that sai driver can generate correct bit clock.
Fixes: 13f3b9fdef6c ("arm64: dts: imx8mm-evk: Enable audio codec wm8524")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add I2C node for switch watchdog present on both Zest and RMB3 boards.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org,
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add I2C node for accelerometer present on both Zest and RMB3 boards.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org,
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
It's 3V3_MAIN, not 3V3V_MAIN on schematic. Fix it.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org,
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Regulator-vsd-3v3 is supplied via GEN_3V3 rail which is an output of
an "always on" load switch supplied by 3V3_MAIN. GEN_3V3 is also used
as vin-supply by a number of peripherals, so adding it also allows us
to follow the schematic more closely.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org,
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Update the property #clock-cells = <1> to #clock-cells = <0> of the
dpclk, since the Display output pixel clock driver provides single
clock output.
Signed-off-by: Wen He <wen.he_1@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add the TMU (Thermal Monitoring Unit) device node to enable
TMU feature.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
SDMA in i.MX8MN should use same configuration as i.MX8MQ
So need to change compatible string to be "fsl,imx8mq-sdma".
Fixes: 6c3debcbae47 ("arm64: dts: freescale: Add i.MX8MN dtsi support")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
SDMA in i.MX8MM should use same configuration as i.MX8MQ
So need to change compatible string to be "fsl,imx8mq-sdma".
Fixes: a05ea40eb384 ("arm64: dts: imx: Add i.mx8mm dtsi support")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The previous patches mechanically transformed the assembly version of
entry.S to entry-common.c for synchronous exceptions.
The C version of local_daif_restore() doesn't quite do the same thing
as the assembly versions if pseudo-NMI is in use. In particular,
| local_daif_restore(DAIF_PROCCTX_NOIRQ)
will still allow pNMI to be delivered. This is not the behaviour
do_el0_ia_bp_hardening() and do_sp_pc_abort() want as it should not
be possible for the PMU handler to run as an NMI until the bp-hardening
sequence has run.
The bp-hardening calls were placed where they are because this was the
first C code to run after the relevant exceptions. As we've now moved
that point earlier, move the checks and calls earlier too.
This makes it clearer that this stuff runs before any kind of exception,
and saves modifying PSTATE twice.
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Cc: Julien Thierry <julien.thierry.kdev@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Now that the callers of these functions have moved into C, they no longer
need the asmlinkage annotation. Remove it.
Signed-off-by: James Morse <james.morse@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
This is largely a 1-1 conversion of asm to C, with a couple of caveats.
The el0_sync{_compat} switches explicitly handle all the EL0 debug
cases, so el0_dbg doesn't have to try to bail out for unexpected EL1
debug ESR values. This also means that an unexpected vector catch from
AArch32 is routed to el0_inv.
We *could* merge the native and compat switches, which would make the
diffstat negative, but I've tried to stay as close to the existing
assembly as possible for the moment.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
[split out of a bigger series, added nokprobes. removed irq trace
calls as the C helpers do this. renamed el0_dbg's use of FAR]
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Cc: Julien Thierry <julien.thierry.kdev@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
This patch converts the EL1 sync entry assembly logic to C code.
Doing this will allow us to make changes in a slightly more
readable way. A case in point is supporting kernel-first RAS.
do_sea() should be called on the CPU that took the fault.
Largely the assembly code is converted to C in a relatively
straightforward manner.
Since all sync sites share a common asm entry point, the ASM_BUG()
instances are no longer required for effective backtraces back to
assembly, and we don't need similar BUG() entries.
The ESR_ELx.EC codes for all (supported) debug exceptions are now
checked in the el1_sync_handler's switch statement, which renders the
check in el1_dbg redundant. This both simplifies the el1_dbg handler,
and makes the EL1 exception handling more robust to
currently-unallocated ESR_ELx.EC encodings.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
[split out of a bigger series, added nokprobes, moved prototypes]
Signed-off-by: James Morse <james.morse@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Cc: Julien Thierry <julien.thierry.kdev@gmail.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Some synchronous exceptions can be taken from a number of contexts,
e.g. where IRQs may or may not be masked. In the entry assembly for
these exceptions, we use the inherit_daif assembly macro to ensure
that we only mask those exceptions which were masked when the exception
was taken.
So that we can do the same from C code, this patch adds a new
local_daif_inherit() function, following the existing local_daif_*()
naming scheme.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
[moved away from local_daif_restore()]
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Functions that are only called by assembly don't always have a
C header file prototype.
Add the prototypes before moving the assembly callers to C.
Signed-off-by: James Morse <james.morse@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Since commit 732674980139 ("arm64: unwind: reference pt_regs via embedded
stack frame") arm64 has not used the __exception annotation to dump
the pt_regs during stack tracing. in_exception_text() has no callers.
This annotation is only used to blacklist kprobes, it means the same as
__kprobes.
Section annotations like this require the functions to be grouped
together between the start/end markers, and placed according to
the linker script. For kprobes we also have NOKPROBE_SYMBOL() which
logs the symbol address in a section that kprobes parses and
blacklists at boot.
Using NOKPROBE_SYMBOL() instead lets kprobes publish the list of
blacklisted symbols, and saves us from having an arm64 specific
spelling of __kprobes.
do_debug_exception() already has a NOKPROBE_SYMBOL() annotation.
Signed-off-by: James Morse <james.morse@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Clang reports a warning on the __tlbi(aside1is, 0) macro expansion since
the value size does not match the register size specified in the inline
asm. Construct the ASID value using the __TLBI_VADDR() macro.
Fixes: 222fc0c8503d ("arm64: compat: Workaround Neoverse-N1 #1542419 for compat user-space")
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Cc: James Morse <james.morse@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
rk3399-roc-pc has three gpio LEDs, enable them.
Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
Link: https://lore.kernel.org/r/7d8d85c9-5fde-7943-a6b6-639bca38bdc1@fivetechno.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This board use uart4 as debug port and arm core voltage
is modulated by pwm, logic voltage is fixed to 1.05V.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Link: https://lore.kernel.org/r/20191021084657.28629-1-andy.yan@rock-chips.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
RK3308 is a quad Cortex A35 based SOC with rich audio
interfaces(I2S/PCM/TDM/PDM/SPDIF/VAD/HDMI ARC), which
designed for intelligent voice interaction and audio
input/output processing.
This patch add basic core dtsi file for it.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Link: https://lore.kernel.org/r/20191021084616.28431-1-andy.yan@rock-chips.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This is unused on cheza. Delete the node to get ride of the reserved-
memory section, and to avoid the driver from attempting to load a zap
shader that doesn't exist every time it powers up the GPU.
This also avoids a massive amount of dmesg spam about missing zap fw:
msm ae00000.mdss: [drm:adreno_request_fw] *ERROR* failed to load
qcom/a630_zap.mdt: -2
adreno 5000000.gpu: [drm:adreno_zap_shader_load] *ERROR* Unable to
load a630_zap.mdt
Signed-off-by: Rob Clark <robdclark@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Fixes: 3fdeaee951aa ("arm64: dts: sdm845: Add zap shader region for GPU")
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <agross@kernel.org>
|
Jon Hunter
Bjorn Andersson
Catalin Marinas
Xiang Zheng
Andreas Färber
Mihaela Martinas
Anson Huang
Christoffer Dall
Olof Johansson
Christian Borntraeger
Stoica Cosmin-Stefan
S.j. Wang
Andrey Smirnov
Wen He
Yuantian Tang
James Morse
Mark Rutland
Markus Reichl
Andy Yan
Rob Clark