| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
i.MX arm64 device tree update for 5.4:
- New board support: i.MX8MQ Nitrogen8m, Hummingboard Pulse,
PICO-PI-IMX8M, i.MX8QXP AI_ML, and LS1046A FRWY board.
- Add gpio-ranges for GPIO devices on i.MX8MQ and i.MX8MM.
- Update OPP table according to latest data sheet and add opp-suspend
to OPP table for i.MX8MQ and i.MX8MM.
- Add IDEL states for i.MX8MM SoC.
- Correct I2C clock divider for Layerscape SoCs.
- Add series alias and LPUART baud clock for i.MX8QXP SoC.
- Add MIPI D-PHY device for i.MX8MQ and enable it on imx8mq-librem5
board.
- Enable USB1 and Type-C support for i.MX8MM EVK board.
- Add Thermal Monitor Unit support for LS1028A SoC.
- Misc small update and correction on Layerscape and i.MX8 support.
* tag 'imx-dt64-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (41 commits)
arm64: dts: imx8mq: Add mux controller to iomuxc_gpr
arm64: dts: fsl: add support for Hummingboard Pulse
arm64: dts: ls1088a: update gpio compatible
arm64: dts: imx: Add i.mx8mq nitrogen8m basic dts support
arm64: dts: ls1088a-qds: Add the spi-flash nodes under the DSPI controller
arm64: dts: ls1088a: Add the DSPI controller node
arm64: dts: imx8mm: Enable cpu-idle driver
arm64: dts: ls1028a: Add esdhc node in dts
arm64: dts: ls1028a: Add properties node for Display output pixel clock
arm64: dts: lx2160a: Fix incorrect I2C clock divider
arm64: dts: ls1028a: Fix incorrect I2C clock divider
arm64: dts: ls1012a: Fix incorrect I2C clock divider
arm64: dts: ls1088a: Fix incorrect I2C clock divider
arm64: dts: ls1028a: fix gpio nodes
arm64: dts: ls1028a: Add Thermal Monitor Unit node
arm64: dts: imx8mq-evk: Unbypass audio_pll1
arm64: dts: imx8mm: Add opp-suspend property to OPP table
arm64: dts: imx8mq: Add opp-suspend property to OPP table
arm64: dts: ls1088a: Revise gpio registers to little-endian
arm64: dts: add the console node for DPAA2 platforms
...
Link: https://lore.kernel.org/r/20190825153237.28829-6-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
i.MX device tree update with new clocks:
- A series from Anson Huang to add i.MX8MN SoC and DDR4 EVK board
device tree support.
- Add DSP device tree support for i.MX8QXP SoC.
* tag 'imx-dt-clkdep-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: imx8qxp: Add DSP DT node
arm64: dts: imx8mn: Add cpu-freq support
arm64: dts: imx8mn-ddr4-evk: Add rohm,bd71847 PMIC support
arm64: dts: imx8mn-ddr4-evk: Add i2c1 support
arm64: dts: freescale: Add i.MX8MN DDR4 EVK board support
arm64: dts: imx8mn: Add gpio-ranges property
arm64: dts: freescale: Add i.MX8MN dtsi support
clk: imx8: Add DSP related clocks
clk: imx: Add support for i.MX8MN clock driver
clk: imx: Add API for clk unregister when driver probe fail
clk: imx8mm: Make 1416X/1443X PLL macro definitions common for usage
dt-bindings: imx: Add clock binding doc for i.MX8MN
Link: https://lore.kernel.org/r/20190825153237.28829-4-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
mt8183:
- fix pwrap interrupt number
- add i2c notes
dt-bindings:
- add compatible for mt6779
- add mt6779 uart and sysirq compatible
* tag 'v5.3-next-dts64' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
dt-bindings: irq: mtk, sysirq: add support for mt6779
dt-bindings: mtk-uart: add mt6779 uart bindings
dt-bindings: mediatek: add support for mt6779 reference board
arm64: dts: mt8183: add I2C nodes
arm64: dts: mt8183: fix pwrap gic number
Link: https://lore.kernel.org/r/def8fb77-fce4-097d-7ae2-8c4670bc09c1@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Allwinner DT changes for 5.4
Our usual pile of patches for the next release, which include mostly:
- More fixes thanks to the DT validation using the YAML bindings
- IR receiver support on the H6
- SPDIF support on the H6
- I2C Support on the H6
- CSI support on the A20
- RTC support on the H6
- New Boards: Lichee Zero Plus, Tanix TX6, A64-Olinuxino-eMMC
* tag 'sunxi-dt-for-5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (40 commits)
arm64: dts: allwinner: orange-pi-3: Enable WiFi
ARM: dts: sunxi: Add missing watchdog clocks
ARM: dts: sunxi: Add missing watchdog interrupts
arm64: dts: allwinner: h6: Add support for RTC and fix the clock tree
ARM: dts: sun7i: Add CSI0 controller
arm64: dts: allwinner: a64: Add A64 OlinuXino board (with eMMC)
dt-bindings: arm: sunxi: Add compatible for A64 OlinuXino with eMMC
ARM: dts: v3s: Change the timers compatible
ARM: dts: h3: Change the timers compatible
ARM: dts: a83t: Change the timers compatible
ARM: dts: a23/a33: Change the timers compatible
ARM: dts: sun6i: Add missing timers interrupts
ARM: dts: sun5i: Add missing timers interrupts
ARM: dts: sun4i: Add missing timers interrupts
dt-bindings: mfd: Convert Allwinner GPADC bindings to a schema
arm64: dts: allwinner: h6: Introduce Tanix TX6 board
dt-bindings: arm: sunxi: Add compatible for Tanix TX6 board
arm64: allwinner: h6: add I2C nodes
dt-bindings: i2c: mv64xxx: Add compatible for the H6 i2c node.
ARM: dts: sunxi: Add mdio bus sub-node to GMAC
...
Link: https://lore.kernel.org/r/d97e6252-9dd7-4cf5-a3cf-56f78b0ca455.lettre@localhost
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Optimize modulo operation instruction generation by
using single MSUB instruction vs MUL followed by SUB
instruction scheme.
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Renesas ARM64 DT updates for v5.4 (take two)
- Sort nodes in various SoC and board DTSes,
- HDMI sound for HiHope RZ/G2M and R-Car M3-N Salvator-X(S) boards,
- Limit EtherAVB to 100Mbps on the Ebisu and Draak boards,
- Small fixes and improvements.
* tag 'renesas-arm64-dt-for-v5.4-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: (21 commits)
arm64: dts: renesas: Update 'vsps' properties for readability
arm64: dts: renesas: r8a77965-salvator-x(s): Enable HDMI sound
arm64: dts: renesas: r8a774c0: Fix register range of display node
arm64: dts: renesas: r8a77970: Sort nodes
arm64: dts: renesas: r8a7796: Sort nodes
arm64: dts: renesas: r8a774c0: Sort nodes
arm64: dts: renesas: r8a774c0: cat874: Sort nodes
arm64: dts: renesas: r8a774a1: Sort nodes
arm64: dts: renesas: r8a77980: Fix IPMMU-VC0 base address
arm64: dts: renesas: ebisu, draak: Limit EtherAVB to 100Mbps
arm64: dts: renesas: hihope-common: Add HDMI audio support
arm64: dts: renesas: r8a774c0: cat874: Add definition for 12V regulator
arm64: dts: renesas: r8a774c0: Point LVDS0 to its companion LVDS1
arm64: dts: renesas: r8a77995: Sort nodes
arm64: dts: renesas: r8a77995: draak: Sort nodes
arm64: dts: renesas: r8a77990: Sort nodes
arm64: dts: renesas: r8a77990: ebisu: Sort nodes
arm64: dts: renesas: r8a77980: v3hsk: Sort nodes
arm64: dts: renesas: r8a77980: condor: Sort nodes
arm64: dts: renesas: r8a77970: v3msk: Sort nodes
...
Link: https://lore.kernel.org/r/20190823123643.18799-4-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
arm64: dts: Amlogic updates for v5.4
Highlights
- new SoCs (G12B family): S922X, A311D
- new SoCs (SM1 family): S905X3
- new board: SEI Robotics SEI610 (SM1/S905X3)
- new board: Khadas VIM3 (G12B/A311D)
- DVFS/CPUfreq support on G12[AB] family
* tag 'amlogic-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic: (40 commits)
arm64: dts: add support for SM1 based SEI Robotics SEI610
dt-bindings: arm: amlogic: add SEI Robotics SEI610 bindings
dt-bindings: arm: amlogic: add SM1 bindings
arm64: dts: meson-g12b-odroid-n2: enable DVFS
arm64: dts: meson-g12b-khadas-vim3: add initial device-tree
dt-bindings: arm: amlogic: fix x96-max/sei510 section in amlogic.yaml
arm64: dts: amlogic: g12 CPU timers stop in suspend
arm64: dts: meson-g12b: support a311d and s922x cpu operating points
dt-bindings: arm: amlogic: add support for the Khadas VIM3
dt-bindings: arm: amlogic: add bindings for the Amlogic G12B based A311D SoC
dt-bindings: arm: amlogic: add bindings for G12B based S922X SoC
arm64: dts: meson: add video decoder entries
arm64: dts: meson-gx: add video decoder entry
dt-bindings: media: amlogic,vdec: add default compatible
arm64: dts: meson: add ethernet fifo sizes
arm64: dts: meson-g12b: add cpus OPP tables
arm64: dts: meson-g12a: enable DVFS on G12A boards
arm64: dts: meson-g12a: add cpus OPP table
arm64: dts: meson-g12-common: add pwm_a on GPIOE_2 pinmux
arm64: dts: move common G12A & G12B modes to meson-g12-common.dtsi
...
Link: https://lore.kernel.org/r/7hr25fbi4v.fsf@baylibre.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
SoCFPGA DTS updates for v5.4
- Add reset properties for various peripherals
- QSPI OCP and DMA on Arria10
- DMA on Agilex/Stratix10
- Update NAND controller bindings to match driver update
- Add NAND controller to Stratix10
- VINING FPGA board fixups
- Update button mapping
- Adjust GMAC1 clock and TXD skew settings
- Add missing reset-names for dma controller
* tag 'socfpga_dts_updates_for_v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: dts: socfpga: add missing reset-names for dma
ARM: dts: socfpga: Adjust GMAC1 clock and TXD lines skew on VINING FPGA
ARM: dts: socfpga: Fix up button mapping on VINING FPGA
arm64: dts: stratix10: Add NAND device node
ARM: dts: socfpga: update to new Denali NAND binding
arm64: dts: agilex/stratix10: Add reset properties for DMA
ARM: dts: socfpga: add reset properties for DMA
ARM: dts: socfpga: add the QSPI OCP reset property on arria10
Link: https://lore.kernel.org/r/20190819141659.26414-1-dinguyen@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
PWM-Fan and nor-flash for the RockPro64, a better display mode for
the Kevin Chromebook and a new board the Leez P710 SBC.
* tag 'v5.4-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Add dts for Leez RK3399 P710 SBC
arm64: dts: rockchip: enable internal SPI flash for RockPro64.
arm64: dts: rockchip: Add PWM fan for RockPro64
arm64: dts: rockchip: Specify override mode for kevin panel
Link: https://lore.kernel.org/r/20190819141659.26414-1-dinguyen@kernel.org
Link: https://lore.kernel.org/r/2362486.gYoCZEsBuK@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
i.MX SoC changes for 5.4:
- Drop AR8031 PHY TX delay adjusting from i.MX7D machine code, as
it's superfluous due to the recent changes to Atheros AT803X driver.
- Select TIMER_IMX_SYS_CTR for arm64 ARCH_MXC platform, since the
system counter is needed as broadcast timer for cpuidle support.
* tag 'imx-soc-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx: stop adjusting ar8031 phy tx delay
arm64: Enable TIMER_IMX_SYS_CTR for ARCH_MXC platforms
Link: https://lore.kernel.org/r/20190825153237.28829-2-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
r8152 conflicts are the NAPI fixes in 'net' overlapping with
some tasklet stuff in net-next
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
QCOM_A53PLL and QCOM_CLK_APCS_MSM8916 used to be enabled by default in
drivers/clk/qcom/Kconfig. A recent patch changed that by dropping the
'default ARCH_QCOM' directive.
Add the two options explicitly in the arm64 defconfig, to avoid
functional regressions.
Acked-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
[bjorn: Rewrote subject]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Now that CONFIG_DRM_MSM is no longer default 'y' add it as a module to all
ARCH_QCOM enabled defconfigs to restore the previous expected build
behavior.
I split this off from the original patch to separate out the ARM64 portions.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
|
|
150MHz is a fundamental limitation of RK3328 Soc, w/o this limitation,
eMMC, for instance, will run into 200MHz clock rate in HS200 mode, which
makes the RK3328 boards not always boot properly. By adding it in
rk3328.dtsi would also obviate the worry of missing it when adding new
boards.
Fixes: 52e02d377a72 ("arm64: dts: rockchip: add core dtsi file for RK3328 SoCs")
Cc: stable@vger.kernel.org
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Liang Chen <cl@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Most archs (well at least x86) store the function call return address on the
stack before storing the local variables for the function. The max stack
tracer depends on this in its algorithm to display the stack size of each
function it finds in the back trace.
Some archs (arm64), may store the return address (from its link register)
just before calling a nested function. There's no reason to save the link
register on leaf functions, as it wont be updated. This breaks the algorithm
of the max stack tracer.
Add a new define ARCH_FTRACE_SHIFT_STACK_TRACER that an architecture may set
if it stores the return address (link register) after it stores the
function's local variables, and have the stack trace shift the values of the
mapped stack size to the appropriate functions.
Link: 20190802094103.163576-1-jiping.ma2@windriver.com
Reported-by: Jiping Ma <jiping.ma2@windriver.com>
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
SDHI3 got accidentally disabled while adding USB 2.0 support,
this patch fixes it.
Fixes: 734d277f412a ("arm64: dts: renesas: hihope-common: Add USB 2.0 support")
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
This adds support for the Turris Mox board from CZ.NIC.
Turris Mox is as modular router based on the Armada 3720 SOC (same as
EspressoBin).
The basic board can be extended by different modules.
If those are connected, U-Boot lets the kernel know via device-tree.
Since modules can be connected in different order and some modules can
be connected multiple times (up to three modules containing 8-port
ethernet switch in DSA configuration can be connected) we decided
against using device-tree overlays, because it got complicated rather
quickly. (For example the SFP module can be connected directly to the
CPU, or after a switch module. There are four cases and all would need
different SFP overlay. There are two types of switch modules (8-port
with pass-through and 4-port with no pass-through). For those we would
again need at least 6 more overlays.)
We therefore decided to put all the possibly connected devices in one
device-tree and disable them by default. When U-Boot finds out which
modules are connected, it fixes the loaded device-tree accordingly just
before boot. By Rob Herring's suggestion we also made it so that U-Boot
completely removes nodes which are disabled after this fixup.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Rob Herring <robh@kernel.org>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
This adds pinctrl node for the GPIO to be used as SPI chip select 1.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Pull ARM SoC fixes from Arnd Bergmann:
"The majority of the fixes this time are for OMAP hardware, here is a
breakdown of the significant changes:
Various device tree bug fixes:
- TI am57xx boards need a voltage level fix to avoid damaging SD
cards
- vf610-bk4 fails to detect its flash due to an incorrect description
- meson-g12a USB phy configuration fails
- meson-g12b reboot should not power off the SD card
- Some corrections for apparently harmless differences from the
documentation.
Regression fixes:
- ams-delta FIQ interrupts broke in 5.3
- TI am3/am4 mmc controllers broke in 5.2
The logic_pio driver (used on some Huawei ARM servers) got a few bug
fixes for reliability.
And a couple of compile-time warning fixes"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (26 commits)
soc: ixp4xx: Protect IXP4xx SoC drivers by ARCH_IXP4XX || COMPILE_TEST
soc: ti: pm33xx: Make two symbols static
soc: ti: pm33xx: Fix static checker warnings
ARM: OMAP: dma: Mark expected switch fall-throughs
ARM: dts: Fix incomplete dts data for am3 and am4 mmc
bus: ti-sysc: Simplify cleanup upon failures in sysc_probe()
ARM: OMAP1: ams-delta-fiq: Fix missing irq_ack
ARM: dts: dra74x: Fix iodelay configuration for mmc3
ARM: dts: am335x: Fix UARTs length
ARM: OMAP2+: Fix omap4 errata warning on other SoCs
bus: hisi_lpc: Add .remove method to avoid driver unbind crash
bus: hisi_lpc: Unregister logical PIO range to avoid potential use-after-free
lib: logic_pio: Add logic_pio_unregister_range()
lib: logic_pio: Avoid possible overlap for unregistering regions
lib: logic_pio: Fix RCU usage
arm64: dts: amlogic: odroid-n2: keep SD card regulator always on
arm64: dts: meson-g12a-sei510: enable IR controller
arm64: dts: meson-g12a: add missing dwc2 phy-names
ARM: dts: vf610-bk4: Fix qspi node description
ARM: dts: Fix incorrect dcan register mapping for am3, am4 and dra7
...
|
|
* for-next/atomics: (10 commits)
Rework LSE instruction selection to use static keys instead of alternatives
|
|
* for-next/52-bit-kva: (25 commits)
Support for 52-bit virtual addressing in kernel space
* for-next/cpu-topology: (9 commits)
Move CPU topology parsing into core code and add support for ACPI 6.3
* for-next/error-injection: (2 commits)
Support for function error injection via kprobes
* for-next/perf: (8 commits)
Support for i.MX8 DDR PMU and proper SMMUv3 group validation
* for-next/psci-cpuidle: (7 commits)
Move PSCI idle code into a new CPUidle driver
* for-next/rng: (4 commits)
Support for 'rng-seed' property being passed in the devicetree
* for-next/smpboot: (3 commits)
Reduce fragility of secondary CPU bringup in debug configurations
* for-next/tbi: (10 commits)
Introduce new syscall ABI with relaxed requirements for pointer tags
* for-next/tlbi: (6 commits)
Handle spurious page faults arising from kernel space
|
|
The 'K' constraint is a documented AArch64 machine constraint supported
by GCC for matching integer constants that can be used with a 32-bit
logical instruction. Unfortunately, some released compilers erroneously
accept the immediate '4294967295' for this constraint, which is later
refused by GAS at assembly time. This had led us to avoid the use of
the 'K' constraint altogether.
Instead, detect whether the compiler is up to the job when building the
kernel and pass the 'K' constraint to our 32-bit atomic macros when it
appears to be supported.
Signed-off-by: Will Deacon <will@kernel.org>
|
|
We use a bunch of internal macros when constructing our atomic and
cmpxchg routines in order to save on boilerplate. Avoid exposing these
directly to users of the header files.
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Support for LSE atomic instructions (CONFIG_ARM64_LSE_ATOMICS) relies on
a static key to select between the legacy LL/SC implementation which is
available on all arm64 CPUs and the super-duper LSE implementation which
is available on CPUs implementing v8.1 and later.
Unfortunately, when building a kernel with CONFIG_JUMP_LABEL disabled
(e.g. because the toolchain doesn't support 'asm goto'), the static key
inside the atomics code tries to use atomics itself. This results in a
mess of circular includes and a build failure:
In file included from ./arch/arm64/include/asm/lse.h:11,
from ./arch/arm64/include/asm/atomic.h:16,
from ./include/linux/atomic.h:7,
from ./include/asm-generic/bitops/atomic.h:5,
from ./arch/arm64/include/asm/bitops.h:26,
from ./include/linux/bitops.h:19,
from ./include/linux/kernel.h:12,
from ./include/asm-generic/bug.h:18,
from ./arch/arm64/include/asm/bug.h:26,
from ./include/linux/bug.h:5,
from ./include/linux/page-flags.h:10,
from kernel/bounds.c:10:
./include/linux/jump_label.h: In function ‘static_key_count’:
./include/linux/jump_label.h:254:9: error: implicit declaration of function ‘atomic_read’ [-Werror=implicit-function-declaration]
return atomic_read(&key->enabled);
^~~~~~~~~~~
[ ... more of the same ... ]
Since LSE atomic instructions are not critical to the operation of the
kernel, make them depend on JUMP_LABEL at compile time.
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
The contents of 'asm/atomic_arch.h' can be split across some of our
other 'asm/' headers. Remove it.
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
The 'alt_lse' assembly macro has been unused since 7c8fc35dfc32
("locking/atomics/arm64: Replace our atomic/lock bitop implementations
with asm-generic").
Remove it.
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Add an accelerated version of the 'essiv(cbc(aes),sha256)' skcipher,
which is used by fscrypt or dm-crypt on systems where CBC mode is
signficantly more performant than XTS mode (e.g., when using a h/w
accelerator which supports the former but not the latter) This avoids
a separate call into the AES cipher for every invocation.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The plain CBC driver and the CTS one share some code that iterates over
a scatterwalk and invokes the CBC asm code to do the processing. The
upcoming ESSIV/CBC mode will clone that pattern for the third time, so
let's factor it out first.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The commit d4609acce187 ("arm64: dts: meson-sm1-sei610: enable DVFS")
incorrectly removed the chosen node and the stdout-path property.
Add these back.
Fixes: d4609acce187 ("arm64: dts: meson-sm1-sei610: enable DVFS")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This enables DVFS for the Amlogic SM1 based SEI610 board by:
- Adding the SM1 SoC OPPs taken from the vendor tree
- Selecting the SM1 Clock controller instead of the G12A one
- Adding the CPU rail regulator, PWM and OPPs for each CPU nodes.
Each power supply can achieve 0.69V to 1.05V using a single PWM
output clocked at 666KHz with an inverse duty-cycle.
DVFS has been tested by running the arm64 cpuburn at [1] and cycling
between all the possible cpufreq translations of the cpu cluster and
checking the final frequency using the clock-measurer, script at [2].
[1] https://github.com/ssvb/cpuburn-arm/blob/master/cpuburn-a53.S
[2] https://gist.github.com/superna9999/d4de964dbc0f84b7d527e1df2ddea25f
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add the Amlogic SM1 based Khadas VIM3L, sharing all the same features
as the G12B based VIM3, but:
- a different DVFS support since only a single cluster is available
- audio is still not available on SM1
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
To prepare support of the Amlogic SM1 based Khadas VIM3, move the non-G12B
specific nodes (all except DVFS and Audio) to a new meson-khadas-vim3.dtsi
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add the reset to the TDM formatters of the g12a. This helps
with channel mapping when a playback/capture uses more than 1 lane.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The clock controller dedicated to audio clocks also provides reset lines
on the g12 SoC family
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This enables DVFS for the Amlogic SM1 based SEI610 board by:
- Adding the SM1 SoC OPPs taken from the vendor tree
- Selecting the SM1 Clock controller instead of the G12A one
- Adding the CPU rail regulator, PWM and OPPs for each CPU nodes.
Each power supply can achieve 0.69V to 1.05V using a single PWM
output clocked at 666KHz with an inverse duty-cycle.
DVFS has been tested by running the arm64 cpuburn at [1] and cycling
between all the possible cpufreq translations of the cpu cluster and
checking the final frequency using the clock-measurer, script at [2].
[1] https://github.com/ssvb/cpuburn-arm/blob/master/cpuburn-a53.S
[2] https://gist.github.com/superna9999/d4de964dbc0f84b7d527e1df2ddea25f
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Swap to the rc-khadas keymap that maps the mouse button to KEY_MUTE.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
add the rc-tx3mini keymap to the ir node
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Swap to the rc-khadas keymap that maps the mouse button to KEY_MUTE.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
add the rc-wetek-play2 keymap to the ir node
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
add the rc-wetek-hub keymap to the ir node
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
add the rc-x96max keymap to the ir node
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
add the rc-odroid keymap to the ir node
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add the USB properties for the Amlogic SM1 Based SEI610 Board in order to
support the USB DRD Type-C port and the USB3 Type A port.
The USB DRD Type-C controller uses the ID signal to toggle the USB role
between the DWC3 Host controller and the DWC2 Device controller.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add the HDMI support nodes for the Amlogic SM1 Based SEI610 Board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Replace the VPU-centric power domain controller by the generic system-wide
Everything-Else power domain controller and setup the right power-domains
properties on the VPU, Ethernet & USB nodes.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
[khilman: minor subject edit: add dts]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This fixes the following DT schemas check errors:
meson-gxbb-odroidc2.dt.yaml: gpio-regulator-tf_io: states:0: Additional items are not allowed (1800000, 1 were unexpected)
meson-gxbb-odroidc2.dt.yaml: gpio-regulator-tf_io: states:0: [3300000, 0, 1800000, 1] is too long
meson-gxbb-nexbox-a95x.dt.yaml: gpio-regulator: states:0: Additional items are not allowed (3300000, 1 were unexpected)
meson-gxbb-nexbox-a95x.dt.yaml: gpio-regulator: states:0: [1800000, 0, 3300000, 1] is too long
meson-gxbb-p200.dt.yaml: gpio-regulator: states:0: Additional items are not allowed (3300000, 1 were unexpected)
meson-gxbb-p200.dt.yaml: gpio-regulator: states:0: [1800000, 0, 3300000, 1] is too long
meson-gxl-s905x-hwacom-amazetv.dt.yaml: gpio-regulator: states:0: Additional items are not allowed (3300000, 1 were unexpected)
meson-gxl-s905x-hwacom-amazetv.dt.yaml: gpio-regulator: states:0: [1800000, 0, 3300000, 1] is too long
meson-gxbb-p201.dt.yaml: gpio-regulator: states:0: Additional items are not allowed (3300000, 1 were unexpected)
meson-gxbb-p201.dt.yaml: gpio-regulator: states:0: [1800000, 0, 3300000, 1] is too long
meson-g12b-odroid-n2.dt.yaml: gpio-regulator-tf_io: states:0: Additional items are not allowed (1800000, 1 were unexpected)
meson-g12b-odroid-n2.dt.yaml: gpio-regulator-tf_io: states:0: [3300000, 0, 1800000, 1] is too long
meson-gxl-s905x-nexbox-a95x.dt.yaml: gpio-regulator: states:0: Additional items are not allowed (3300000, 1 were unexpected)
meson-gxl-s905x-nexbox-a95x.dt.yaml: gpio-regulator: states:0: [1800000, 0, 3300000, 1] is too long
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This fixes the following DT schemas check errors:
meson-gxbb-p201.dt.yaml: ethernet@c9410000: snps,reset-delays-us: [[0, 10000, 1000000]] is too short
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This fixes the following DT schemas check errors:
meson-gxbb-nanopi-k2.dt.yaml: /: 'model' is a required property
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This fixes the following DT schemas check errors:
meson-g12a-x96-max.dt.yaml: /: compatible: ['amediatech,x96-max', 'amlogic,u200', 'amlogic,g12a'] is not valid under any of the given schemas
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This fixes the following DT schemas check errors:
meson-g12a-u200.dt.yaml: reset-controller@1004: compatible:0: 'amlogic,meson-g12a-reset' is not one of ['amlogic,meson8b-reset', 'amlogic,meson-gxbb-reset', 'amlogic,meson-axg-reset']
meson-g12a-sei510.dt.yaml: reset-controller@1004: compatible:0: 'amlogic,meson-g12a-reset' is not one of ['amlogic,meson8b-reset', 'amlogic,meson-gxbb-reset', 'amlogic,meson-axg-reset']
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
Arnd Bergmann
Jerin Jacob
David S. Miller
Marc Gonzalez
Jordan Crouse
Shawn Lin
Steven Rostedt (VMware)
Fabrizio Castro
Marek Behún
Linus Torvalds
Will Deacon
Ard Biesheuvel
Neil Armstrong
Jerome Brunet
Christian Hewitt