| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Merge conflict of mlx5 resolved using instructions in merge
commit 9566e650bf7fdf58384bb06df634f7531ca3a97e.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to rock64 schemetic V2 and V3, the VCC_HOST_5V output is
controlled by USB_20_HOST_DRV, which is the same as VCC_HOST1_5V.
V1 hardware was never sold and only V2/V3 is with customers,
so there is no need to keep a seaprate v1 version around.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
This includes DSP reserved memory, ADMA DSP device and DSP MU
communication channels description.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add A53 OPP table, cpu regulator and speed grading node to
support cpu-freq driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
On i.MX8MN DDR4 EVK board, there is a rohm,bd71847 PMIC
on i2c1 bus, enable it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable i2c1 on i.MX8MN DDR4 EVK board.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This patch adds basic i.MM8MN DDR4 EVK board support.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add "gpio-ranges" property to establish connections between GPIOs
and PINs on i.MX8MN pinctrl driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The i.MX8M Nano Media Applications Processor is a new SoC of the i.MX8M
family, it is a 14nm FinFET product of the growing mScale family targeting
the consumer market. It is built in Samsung 14LPP to achieve both high
performance and low power consumption and relies on a powerful fully
coherent core complex based on a quad core ARM Cortex-A53 cluster,
Cortex-M7 low-power coprocessor and graphics accelerator.
This patch adds the basic dtsi support for i.MX8MN.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable i.MX8MM cpu-idle using generic ARM cpu-idle driver, 2 states
are supported, details as below:
root@imx8mmevk:~# cat /sys/devices/system/cpu/cpu0/cpuidle/state0/name
WFI
root@imx8mmevk:~# cat /sys/devices/system/cpu/cpu0/cpuidle/state0/usage
3973
root@imx8mmevk:~# cat /sys/devices/system/cpu/cpu0/cpuidle/state1/name
cpu-pd-wait
root@imx8mmevk:~# cat /sys/devices/system/cpu/cpu0/cpuidle/state1/usage
6647
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This patch is to add esdhc node and enable SD UHS-I,
eMMC HS200 for ls1028ardb/ls1028aqds board.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The LS1028A has a clock domain PXLCLK0 used for the Display output
interface in the display core, independent of the system bus frequency,
for flexible clock design. This display core has its own pixel clock.
This patch enable the pixel clock provider on the LS1028A.
Signed-off-by: Wen He <wen.he_1@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Lx2160a platform, the i2c input clock is actually platform pll CLK / 16
(this is the hardware connection), other clock divider can not get the
correct i2c clock, resulting in the output of SCL pin clock is not
accurate.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Ls1028a platform, the i2c input clock is actually platform pll CLK / 4
(this is the hardware connection), other clock divider can not get the
correct i2c clock, resulting in the output of SCL pin clock is not
accurate.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Ls1012a platform, the i2c input clock is actually platform pll CLK / 4
(this is the hardware connection), other clock divider can not get the
correct i2c clock, resulting in the output of SCL pin clock is not
accurate.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Ls1088a platform, the i2c input clock is actually platform pll CLK / 8
(this is the hardware connection), other clock divider can not get the
correct i2c clock, resulting in the output of SCL pin clock is not
accurate.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Update the nodes to include little-endian
property to be consistent with the hardware.
Signed-off-by: Song Hui <hui.song_1@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Thermal Monitoring Unit (TMU) monitors and reports the
temperature from 2 remote temperature measurement sites
located on ls1028a chip.
Add TMU dts node to enable this feature.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.50 of Feb
12, 2019, the base address of the IPMMU-VC0 block on R-Car V3H is
0xfe990000.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
|
|
* According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of
August 24, 2018, the TX clock internal delay mode isn't supported
on R-Car E3 (r8a77990) and D3 (r8a77995).
* TX clock internal delay mode is required for reliable 1Gbps communication
using the KSZ9031RNX phy present on the Ebisu and Draak boards.
Thus, the E3 based Ebisu and D3 based Draak boards can not reliably
use 1Gbps and the speed should be limited to 100Mbps.
Based on work by Kazuya Mizuguchi.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
This patch adds support for HDMI audio to the device tree
common to the HiHope RZ/G2M and the HiHope RZ/G2N.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
For VPIPT I-caches, we need I-cache maintenance on VMID rollover to
avoid an ABA problem. Consider a single vCPU VM, with a pinned stage-2,
running with an idmap VA->IPA and idmap IPA->PA. If we don't do
maintenance on rollover:
// VMID A
Writes insn X to PA 0xF
Invalidates PA 0xF (for VMID A)
I$ contains [{A,F}->X]
[VMID ROLLOVER]
// VMID B
Writes insn Y to PA 0xF
Invalidates PA 0xF (for VMID B)
I$ contains [{A,F}->X, {B,F}->Y]
[VMID ROLLOVER]
// VMID A
I$ contains [{A,F}->X, {B,F}->Y]
Unexpectedly hits stale I$ line {A,F}->X.
However, for PIPT and VIPT I-caches, the VMID doesn't affect lookup or
constrain maintenance. Given the VMID doesn't affect PIPT and VIPT
I-caches, and given VMID rollover is independent of changes to stage-2
mappings, I-cache maintenance cannot be necessary on VMID rollover for
PIPT or VIPT I-caches.
This patch removes the maintenance on rollover for VIPT and PIPT
I-caches. At the same time, the unnecessary colons are removed from the
asm statement to make it more legible.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Christoffer Dall <christoffer.dall@arm.com>
Reviewed-by: James Morse <james.morse@arm.com>
Cc: Julien Thierry <julien.thierry.kdev@gmail.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: kvmarm@lists.cs.columbia.edu
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
'7d0c76bdf227 ("clk: qcom: Add WCSS gcc clock control for QCS404")'
introduces two new clocks to gcc. These are not used before
clk_disable_unused() and as such the clock framework tries to disable
them.
But on the EVB these registers are only accessible through TrustZone, so
these clocks must be marked as "protected" to prevent the clock code
from touching them.
Numerical values are used as the constants are not yet available in a
common tree.
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reported-by: Mark Brown <broonie@kernel.org>
Reported-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Pull arm64 fixes from Catalin Marinas:
- Don't taint the kernel if CPUs have different sets of page sizes
supported (other than the one in use).
- Issue I-cache maintenance for module ftrace trampoline.
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: ftrace: Ensure module ftrace trampoline is coherent with I-side
arm64: cpufeature: Don't treat granule sizes as strict
|
|
The initial support for dynamic ftrace trampolines in modules made use
of an indirect branch which loaded its target from the beginning of
a special section (e71a4e1bebaf7 ("arm64: ftrace: add support for far
branches to dynamic ftrace")). Since no instructions were being patched,
no cache maintenance was needed. However, later in be0f272bfc83 ("arm64:
ftrace: emit ftrace-mod.o contents through code") this code was reworked
to output the trampoline instructions directly into the PLT entry but,
unfortunately, the necessary cache maintenance was overlooked.
Add a call to __flush_icache_range() after writing the new trampoline
instructions but before patching in the branch to the trampoline.
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: James Morse <james.morse@arm.com>
Cc: <stable@vger.kernel.org>
Fixes: be0f272bfc83 ("arm64: ftrace: emit ftrace-mod.o contents through code")
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
P710 is a RK3399 based SBC, designed by Leez [0].
Specification
- Rockchip RK3399
- 4/2GB LPDDR4
- TF sd scard slot
- eMMC
- M.2 B-Key for 4G LTE
- AP6256 for WiFi + BT
- Gigabit ethernet
- HDMI out
- 40 pin header
- USB 2.0 x 2
- USB 3.0 x 1
- USB 3.0 Type-C x 1
- TYPE-C Power supply
[0]https://leez.lenovo.com
Signed-off-by: Andy Yan <andyshrk@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The rockpro64 contains a nor-flash chip connected to spi1.
Signed-off-by: Andrius Štikonas <andrius@stikonas.eu>
[a number of cleanups]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Enable the ACPI_APEI_PCIEAER configuration to support PCIe AER error report
for the Hisilicon D06 board and the dependencies PCIEAER and ACPI_APEI have
been enabled in the default config.
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
|
|
Enable the DesignWare watchdog driver that is present on the Intel
Stratix10 and Agilex platforms.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
|
|
arm64: dts: Amlogic fixes for v5.3-rc
- a few small DT fixes for g12a/g12b platforms
* tag 'amlogic-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
arm64: dts: amlogic: odroid-n2: keep SD card regulator always on
arm64: dts: meson-g12a-sei510: enable IR controller
arm64: dts: meson-g12a: add missing dwc2 phy-names
|
|
No module currently messed with clearing or setting the execute
permission of kernel memory, and none really should.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
The trusted OS may reject CPU_OFF calls to its resident CPU, so we must
avoid issuing those. We never migrate a Trusted OS and we already take
care to prevent CPU_OFF PSCI call. However, this is not reflected
explicitly to the userspace. Any user can attempt to hotplug trusted OS
resident CPU. The entire motion of going through the various state
transitions in the CPU hotplug state machine gets executed and the
PSCI layer finally refuses to make CPU_OFF call.
This results is unnecessary unwinding of CPU hotplug state machine in
the kernel. Instead we can mark the trusted OS resident CPU as not
available for hotplug, so that the user attempt or request to do the
same will get immediately rejected.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
ARMv8 Juno/FVP update for v5.4
Single patch removing optional 'max-memory-bandwidth' property for CLCD
that enables to allocate and use 32bpp buffers(used on FVP for Android
development)
* tag 'juno-update-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: fast models: Remove clcd's max-memory-bandwidth
Link: https://lore.kernel.org/r/20190814172408.25995-1-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
It seems that LLVM's linker does not correctly handle variable assignments
involving section positions that are updated during the SECTIONS
parsing. Commit aa69fb62bea1 ("arm64/efi: Mark __efistub_stext_offset as
an absolute symbol explicitly") ran into this too, but found a different
workaround.
However, this was not enough, as other variables were also miscalculated
which manifested as boot failures under UEFI where __efistub__end was
not taking the correct _end value (they should be the same):
$ ld.lld -EL -maarch64elf --no-undefined -X -shared \
-Bsymbolic -z notext -z norelro --no-apply-dynamic-relocs \
-o vmlinux.lld -T poc.lds --whole-archive vmlinux.o && \
readelf -Ws vmlinux.lld | egrep '\b(__efistub_|)_end\b'
368272: ffff000002218000 0 NOTYPE LOCAL HIDDEN 38 __efistub__end
368322: ffff000012318000 0 NOTYPE GLOBAL DEFAULT 38 _end
$ aarch64-linux-gnu-ld.bfd -EL -maarch64elf --no-undefined -X -shared \
-Bsymbolic -z notext -z norelro --no-apply-dynamic-relocs \
-o vmlinux.bfd -T poc.lds --whole-archive vmlinux.o && \
readelf -Ws vmlinux.bfd | egrep '\b(__efistub_|)_end\b'
338124: ffff000012318000 0 NOTYPE LOCAL DEFAULT ABS __efistub__end
383812: ffff000012318000 0 NOTYPE GLOBAL DEFAULT 15325 _end
To work around this, all of the __efistub_-prefixed variable assignments
need to be moved after the linker script's SECTIONS entry. As it turns
out, this also solves the problem fixed in commit aa69fb62bea1, so those
changes are reverted here.
Link: https://github.com/ClangBuiltLinux/linux/issues/634
Link: https://bugs.llvm.org/show_bug.cgi?id=42990
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Strengthen the wording in the documentation for cpu_enable() to make it
more obvious to readers not already familiar with the code when the core
will call this callback and that this is intentional.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
[will: minor tweak to emphasis in the comment]
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Prior to commit:
14c127c957c1c607 ("arm64: mm: Flip kernel VA space")
... VA_START described the start of the TTBR1 address space for a given
VA size described by VA_BITS, where all kernel mappings began.
Since that commit, VA_START described a portion midway through the
address space, where the linear map ends and other kernel mappings
begin.
To avoid confusion, let's rename VA_START to PAGE_END, making it clear
that it's not the start of the TTBR1 address space and implying that
it's related to PAGE_OFFSET. Comments and other mnemonics are updated
accordingly, along with a typo fix in the decription of VMEMMAP_SIZE.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Steve Capper <steve.capper@arm.com>
Reviewed-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
VA_START used to be the start of the TTBR1 address space, but now it's a
point midway though. In a couple of places we still use VA_START to get
the start of the TTBR1 address space, so let's fix these up to use
PAGE_OFFSET instead.
Fixes: 14c127c957c1c607 ("arm64: mm: Flip kernel VA space")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Steve Capper <steve.capper@arm.com>
Reviewed-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Renesas ARM64 DT updates for v5.4
- CAN, BT, and WLAN support for the HiHope RZ/G2[MN] boards,
- Sound support for RZ/G2M,
- Sort nodes in various SoC and board DTSes,
- Small fixes and improvements.
* tag 'renesas-arm64-dt-for-v5.4-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: (23 commits)
arm64: dts: renesas: ulcb: Sort nodes
arm64: dts: renesas: ulcb-kf: Sort nodes
arm64: dts: renesas: salvator-common: Sort nodes
arm64: dts: renesas: r8a7796: salvator-xs: Sort nodes
arm64: dts: renesas: r8a7796: salvator-x: Sort nodes
arm64: dts: renesas: r8a7795: salvator-xs: Sort nodes
arm64: dts: renesas: r8a7795: salvator-x: Sort nodes
arm64: dts: renesas: r8a7795-es1: salvator-x: Sort nodes
arm64: dts: renesas: r8a77965: Sort nodes
arm64: dts: renesas: r8a7795-es1: Sort nodes
arm64: dts: renesas: r8a7795: Sort nodes
arm64: dts: renesas: r8a774a1: Add SSIU support for sound
arm64: dts: renesas: r8a774a1: Use extended audio dmac registers
arm64: dts: renesas: hihope-common: Add WLAN support
arm64: dts: renesas: hihope-common: Add BT support
arm64: dts: renesas: hihope-common: Add PCA9654 I/O expander
arm64: dts: renesas: hihope-rzg2-ex: Enable CAN interfaces
arm64: dts: renesas: r8a774a1: Add CANFD support
arm64: dts: renesas: r8a774a1: Add missing assigned-clocks for CAN[01]
arm64: dts: renesas: r8a774c0: Add missing assigned-clocks for CAN[01]
...
Link: https://lore.kernel.org/r/20190802120355.1430-2-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Enable the PSCI CPUidle driver to replace the functionality
previously provided by the generic ARM CPUidle driver through
CPU operations.
Link: https://lore.kernel.org/r/20190814125239.6270-2-lorenzo.pieralisi@arm.com
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Cleanup memory.h so that the indentation is consistent, remove pointless
line-wrapping and use consistent parameter names for different versions
of the same macro.
Reviewed-by: Steve Capper <steve.capper@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Commenting the #endif of a multi-statement #ifdef block with the
condition which guards it is useful and can save having to scroll back
through the file to figure out which set of Kconfig options apply to
a particular piece of code.
Reviewed-by: Steve Capper <steve.capper@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
There's no need for __tag_set() to be a complicated macro when
CONFIG_KASAN_SW_TAGS=y and a simple static inline otherwise. Rewrite
the thing as a common static inline function.
Tested-by: Steve Capper <steve.capper@arm.com>
Reviewed-by: Steve Capper <steve.capper@arm.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Rather than subtracting from -1 and then adding 1, we can simply
subtract from 0.
Tested-by: Steve Capper <steve.capper@arm.com>
Reviewed-by: Steve Capper <steve.capper@arm.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Build virt_to_page() on top of virt_to_pfn() so we can avoid the need
for explicit shifting.
Tested-by: Steve Capper <steve.capper@arm.com>
Reviewed-by: Steve Capper <steve.capper@arm.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
The default implementations of page_to_virt() and virt_to_page() are
fairly confusing to read and the former evaluates its 'page' parameter
twice in the macro
Rewrite them so that the computation is expressed as 'base + index' in
both cases and the parameter is always evaluated exactly once.
Tested-by: Steve Capper <steve.capper@arm.com>
Reviewed-by: Steve Capper <steve.capper@arm.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
When converting a linear virtual address to a physical address, pfn or
struct page *, we must make sure that the tag bits are masked before the
calculation otherwise we end up with corrupt pointers when running with
CONFIG_KASAN_SW_TAGS=y:
| Unable to handle kernel paging request at virtual address 0037fe0007580d08
| [0037fe0007580d08] address between user and kernel address ranges
Mask out the tag in __virt_to_phys_nodebug() and virt_to_page().
Reported-by: Qian Cai <cai@lca.pw>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Steve Capper <steve.capper@arm.com>
Reviewed-by: Steve Capper <steve.capper@arm.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Fixes: 9cb1c5ddd2c4 ("arm64: mm: Remove bit-masking optimisations for PAGE_OFFSET and VMEMMAP_START")
Signed-off-by: Will Deacon <will@kernel.org>
|
|
virt_addr_valid() is intended to test whether or not the passed address
is a valid linear map address. Unfortunately, it relies on
_virt_addr_is_linear() which is broken because it assumes the linear
map is at the top of the address space, which it no longer is.
Reimplement virt_addr_valid() using __is_lm_address() and remove
_virt_addr_is_linear() entirely. At the same time, ensure we evaluate
the macro parameter only once and move it within the __ASSEMBLY__ block.
Reported-by: Qian Cai <cai@lca.pw>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Steve Capper <steve.capper@arm.com>
Reviewed-by: Steve Capper <steve.capper@arm.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Fixes: 14c127c957c1 ("arm64: mm: Flip kernel VA space")
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Pull in generic CPU topology changes from Paul Walmsley (RISC-V).
* tag 'common/for-v5.4-rc1/cpu-topology' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
MAINTAINERS: Add an entry for generic architecture topology
base: arch_topology: update Kconfig help description
RISC-V: Parse cpu topology during boot.
arm: Use common cpu_topology structure and functions.
cpu-topology: Move cpu topology code to common code.
dt-binding: cpu-topology: Move cpu-map to a common binding.
Documentation: DT: arm: add support for sockets defining package boundaries
|
|
All instances of struct sys64_hook contain compile-time constant data,
and are never inentionally modified, so let's make them all const.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
The aarch64_insn_encoding_class[] array contains compile-time constant
data, and is never intentionally modified, so let's mark it as const.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
David S. Miller
Kever Yang
Daniel Baluta
Anson Huang
Ashish Kumar
Wen He
Chuanhua Han
Song Hui
Yuantian Tang
Geert Uytterhoeven
Simon Horman
Fabrizio Castro
Mark Rutland
Bjorn Andersson
Linus Torvalds
Will Deacon
Andy Yan
Andrius Štikonas
Zhou Wang
Dinh Nguyen
Arnd Bergmann
Christoph Hellwig
Sudeep Holla
Kees Cook
Mark Brown
Lorenzo Pieralisi