| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This commit enable the hdmi-sound and i2s2 devices needed to have
audio over HDMI on both rock960 and the related ficus board.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add RSC (Resource State Coordinator) provider
dictating network-on-chip interconnect bus performance
found on SDM845-based platforms.
Signed-off-by: David Dai <daidavid1@codeaurora.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Initializing the SMMU trips a security violation, so disable the VFE
SMMU for now.
Fixes: f3442ab97257 ("arm64: dts: qcom: msm8996: Add VFE SMMU node")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Add the rpm clock controller node, to provide the low-noise baseband
clock for the USB PHYs, among other things.
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Add MSM8998 Resource Power Manager Clock Controller DT node.
Tested-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Add nodes for USB and related PHYs.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
This adds a reference to the dts of the Raspberry Pi 3 A+,
so we don't need to maintain the content in arm64.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
|
|
During resume hibernate restores all physical memory. Any memory
that is accessed with the MMU disabled needs to be cleaned to the
PoC.
KVMs __hyp_text was previously ommitted as it runs with the MMU
enabled, but now that the hyp-stub is located in this section,
we must clean __hyp_text too.
This ensures secondary CPUs that come online after hibernate
has finished resuming, and load KVM via the freshly written
hyp-stub see the correct instructions.
Signed-off-by: James Morse <james.morse@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
The hyp-stub is loaded by the kernel's early startup code at EL2
during boot, before KVM takes ownership later. The hyp-stub's
text is part of the regular kernel text, meaning it can be kprobed.
A breakpoint in the hyp-stub causes the CPU to spin in el2_sync_invalid.
Add it to the __hyp_text.
Signed-off-by: James Morse <james.morse@arm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
On systems with VHE the kernel and KVM's world-switch code run at the
same exception level. Code that is only used on a VHE system does not
need to be annotated as __hyp_text as it can reside anywhere in the
kernel text.
__hyp_text was also used to prevent kprobes from patching breakpoint
instructions into this region, as this code runs at a different
exception level. While this is no longer true with VHE, KVM still
switches VBAR_EL1, meaning a kprobe's breakpoint executed in the
world-switch code will cause a hyp-panic.
Move the __hyp_text check in the kprobes blacklist so it applies on
VHE systems too, to cover the common code and guest enter/exit
assembly.
Fixes: 888b3c8720e0 ("arm64: Treat all entry code as non-kprobe-able")
Reviewed-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: James Morse <james.morse@arm.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Commit 1598ecda7b23 ("arm64: kaslr: ensure randomized quantities are
clean to the PoC") added cache maintenance to ensure that global
variables set by the kaslr init routine are not wiped clean due to
cache invalidation occurring during the second round of page table
creation.
However, if kaslr_early_init() exits early with no randomization
being applied (either due to the lack of a seed, or because the user
has disabled kaslr explicitly), no cache maintenance is performed,
leading to the same issue we attempted to fix earlier, as far as the
module_alloc_base variable is concerned.
Note that module_alloc_base cannot be initialized statically, because
that would cause it to be subject to a R_AARCH64_RELATIVE relocation,
causing it to be overwritten by the second round of KASLR relocation
processing.
Fixes: f80fb3a3d508 ("arm64: add support for kernel ASLR")
Cc: <stable@vger.kernel.org> # v4.6+
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Commit 3b8c9f1cdfc5 ("arm64: IPI each CPU after invalidating the I-cache
for kernel mappings") was aimed at fixing the I-cache invalidation for
kernel mappings. However, it inadvertently caused all cache maintenance
for user mappings via set_pte_at() -> __sync_icache_dcache() ->
sync_icache_aliases() to call kick_all_cpus_sync().
Reported-by: Shijith Thotton <sthotton@marvell.com>
Tested-by: Shijith Thotton <sthotton@marvell.com>
Reported-by: Wandun Chen <chenwandun@huawei.com>
Fixes: 3b8c9f1cdfc5 ("arm64: IPI each CPU after invalidating the I-cache for kernel mappings")
Cc: <stable@vger.kernel.org> # 4.19.x-
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Add two new ptrace regsets, which can be used to request and change the
pointer authentication keys of a thread. NT_ARM_PACA_KEYS gives access
to the instruction/data address keys, and NT_ARM_PACG_KEYS to the
generic authentication key. The keys are also part of the core dump file
of the process.
The regsets are only exposed if the kernel is compiled with
CONFIG_CHECKPOINT_RESTORE=y, as the only intended use case is
checkpointing and restoring processes that are using pointer
authentication. (This can be changed later if there are other use
cases.)
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
TERES-I has ACIN connector and battery.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Enable Camera sensor interface for Allwinner SUN6I SoC's.
This support enable V4L2 platform drivers static and
VIDEO_SUN6I_CSI as module.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The GPIO-based bitbanging I2C driver is required to configure
CSI data, clock pins on CSI block in Allwinner A64 SoC.
Let build it as module.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Add the fsl,magic-packet property in the fec node.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Populate the fec1 node with the missing MDIO and PHY entries.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
It enables USB3 host device support for imx8mq-evk board.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
It adds USB device and phy nodes for imx8mq SoC.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
On the am654x-evm, sdhci0 node is connected to an eMMC. Add node and
pinmux for the same.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
Add support for the Secure Digital Host Controller Interface (SDHCI)
present on TI's AM654 SOCs. It is compatible with eMMC5.1 Host
Specifications.
Enable only upto HS200 speed mode.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
|
|
The ATF on the i.MX8MQ device disables all non-essential power
domains. For correct on-SoC peripheral operation we need both
the power domain driver and generic domains, so device driver
probe gets ordered behind the power domain controller driver.
Select those options, as those being absent can lead to very
hard to debug failures.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The GPCv2 sits between most of the peripherals and the GIC and
functions as a wakeup controller for the CPU cores.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The system is unable to boot without this driver being present,
as most of the peripherals are connected to this IRQ controller.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The arm64 CRC-T10DIF implementation either uses 8-bit or 64-bit
polynomial multiplication instructions, since the latter are
faster but not mandatory in the architecture.
Since that prevents us from testing both implementations on the
same system, let's expose both implementations to the crypto API,
with the priorities reflecting that the P64 version is the
preferred one if available.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Remove some code that is no longer called now that we make sure never
to invoke the SIMD routine with less than 16 bytes of input.
Reviewed-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The SIMD routine ported from x86 used to have a special code path
for inputs < 16 bytes, which got lost somewhere along the way.
Instead, the current glue code aligns the input pointer to 16 bytes,
which is not really necessary on this architecture (although it
could be beneficial to performance to expose aligned data to the
the NEON routine), but this could result in inputs of less than
16 bytes to be passed in. This not only fails the new extended
tests that Eric has implemented, it also results in the code
reading past the end of the input, which could potentially result
in crashes when dealing with less than 16 bytes of input at the
end of a page which is followed by an unmapped page.
So update the glue code to only invoke the NEON routine if the
input is at least 16 bytes.
Reported-by: Eric Biggers <ebiggers@kernel.org>
Reviewed-by: Eric Biggers <ebiggers@kernel.org>
Fixes: 6ef5737f3931 ("crypto: arm64/crct10dif - port x86 SSE implementation to arm64")
Cc: <stable@vger.kernel.org> # v4.10+
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The arm64 GHASH implementation either uses 8-bit or 64-bit
polynomial multiplication instructions, since the latter are
faster but not mandatory in the architecture.
Since that prevents us from testing both implementations on the
same system, let's expose both implementations to the crypto API,
with the priorities reflecting that the P64 version is the
preferred one if available.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
When the AES-CCM code was first added, the NEON register were saved
and restored eagerly, and so the code avoided doing so, and executed
the scatterwalk in atomic context inside the kernel_neon_begin/end
section.
This has been changed in the meantime, so switch to non-atomic
scatterwalks.
Fixes: bd2ad885e30d ("crypto: arm64/aes-ce-ccm - move kernel mode neon ...")
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Commit 5092fcf34908 ("crypto: arm64/aes-ce-ccm: add non-SIMD generic
fallback") introduced C fallback code to replace the NEON routines
when invoked from a context where the NEON is not available (i.e.,
from the context of a softirq taken while the NEON is already being
used in kernel process context)
Fix two logical flaws in the MAC calculation of the associated data.
Reported-by: Eric Biggers <ebiggers@kernel.org>
Fixes: 5092fcf34908 ("crypto: arm64/aes-ce-ccm: add non-SIMD generic fallback")
Cc: stable@vger.kernel.org
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The NEON MAC calculation routine fails to handle the case correctly
where there is some data in the buffer, and the input fills it up
exactly. In this case, we enter the loop at the end with w8 == 0,
while a negative value is assumed, and so the loop carries on until
the increment of the 32-bit counter wraps around, which is quite
obviously wrong.
So omit the loop altogether in this case, and exit right away.
Reported-by: Eric Biggers <ebiggers@kernel.org>
Fixes: a3fd82105b9d1 ("arm64/crypto: AES in CCM mode using ARMv8 Crypto ...")
Cc: stable@vger.kernel.org
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Flash mt35xu512aba connected to FlexSPI controller supports
1-1-8/1-8-8 protocol.
Added flag spi-rx-bus-width and spi-tx-bus-width with values as
8 and 8 respectively for both flashes connected at CS0 and CS1.
Signed-off-by: Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The boot from eMMC is currently broken on the NXP i.MX8MQ EVK board.
When trying to boot from eMMC it fails with:
...
[ 1.271938] mmc1: Tuning failed, falling back to fixed sampling clock
[ 1.287429] print_req_error: I/O error, dev mmcblk1, sector 1 flags 0
[ 1.306833] mmc1: Tuning failed, falling back to fixed sampling clock
[ 1.322325] print_req_error: I/O error, dev mmcblk1, sector 2 flags 0
[ 1.329559] Buffer I/O error on dev mmcblk1, logical block 0, async page read
[ 1.336714] mmcblk1: unable to read partition table
...
The problem is the result of a partial misconfiguration of the pins and
the missing assigned clock rate.
Fixes: 9079aca4aacd ("arm64: add support for i.MX8M EVK board")
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Tested-by: Chris Spencer <christopher.spencer@sea.co.uk>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add devicetree support for Oxalis SoM board from EBS-SYSTART. This
board is one of the 96Boards Enterprise Edition platform. Below are some
of the key features of this board:
* SoC: NXP Layerscape LS1012A
* RAM: 1GB DDR3L
* PMU: NXP VR5100
* Storage: 64MByte SPI Flash for bootloader and RCW, MicroSD Card, SATA
* Connectivity: 2x Ethernet
* USB: 2x USB3.0
More information about this board can be found in 96Boards product
page: https://www.96boards.org/product/oxalis/
Ethernet and SPI flash are not supported yet!
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add fspi node property for LX2160A SoC for FlexSPI driver.
Property added for the FlexSPI controller and for the connected
slave device for the LX2160ARDB target.
This is having two SPI-NOR flash device, mt35xu512aba, connected
at CS0 and CS1.
Signed-off-by: Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Peng Donglin <dolinux.peng@gmail.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
It fixes malformed SPDX license identifier in Hi3798CV200 and Poplar
DTS, accroding to Documentation/process/license-rules.rst.
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
|
|
The SDcard detection of hikey960 is active low so cd-inverted is wrong.
Instead of adding cd-inverted, we should better set correctly cd-gpios
to use GPIO_ACTIVE_LOW.
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
|
|
Add dma0 references for bluetooth uart to enable dma
for bt transfers.
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Ryan Grachek <ryan@edited.us>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
|
|
This switches out the old fbdev PL11x driver to the new
DRM driver in the Aarch64/ARM64 defconfig. Some ARM
reference designs use this IP with the Silicon Image
SII902x HDMI bridge so activate both.
The required DTS changes are already in-tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
ARMv8 Juno/fast models updates for v5.1
1. Support for Fixed Virtual Platforms(FVP) Base RevC model to enable
development of software around the new features available
2. Addition of dynamic-power-coefficient information for CPUs on Juno
3. Miscellaneous changes like re-ordering device nodes, using existing
macros for GIC flags in interrupt-maps and using list instead of
tuple(which is wrong but works as number of interrupt cells is 1)
for mmci interrupts
* tag 'juno-updates-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: juno: Add cpu dynamic-power-coefficient information
arm64: dts: fast models: Add DTS fo Base RevC FVP
arm64: dts: juno/fast models: sort couple of device nodes
arm64: dts: models: use list instead of tuple for mmci interrupts
arm64: dts: juno/fast models: using GIC macros instead of hardcoded values
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Allwinner DT64 changes for 5.1
A few small improvements for the A64 this cycle:
- ARM PMU added
- Allwinner ARM architected timer workaround enabled
This works around timer value wrapping found in the Allwinner
implementation of the ARM architected timer.
* tag 'sunxi-dt64-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: a64: Enable A64 timer workaround
arm64: dts: allwinner: a64: Fix a typo
arm64: dts: allwinner: a64: Add PMU node
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Renesas ARM64 Based SoC DT Updates for v5.1
R-Car H3 (r8a7795) SoC
- Sort i2c and pciec0 nodes within soc node
R-Car H3 (r8a7795) and M3-W (r8a7796) SoCs
- Remove BUSIF0 settings from rcar_sound,ssi
R-Car M3-W (r8a7796) based Salvator-XS board
- Convert to new LVDS DT bindings
R-Car H3 (r8a7795), M3-W (r8a7796) and M3-N (r8a77965) based ULCB boards
- Use audio-graph-card to allow secondary sound device on kingfisher
daugher board
- Add HDMI sound support
Kingfisher daughterboard for R-Car H3 (r8a7795), M3-W (r8a7796) and M3-N
(r8a77965) based ULCB boards
- Add pcm3168 sound codec
R-Car E3 (r8a77990) SoC
- Enable DMA for SCIF2
R-Car E3 (r8a77990) based Ebisu board
- HS400 for onboard eMMC
- Use simple-audio-card rather than simple-scu-audio-card
- Correct EthernetAVB phy mode as rgmii
- Add backlight and follow-up to correct duplicate regulator number
R-Car V3M (r8a77970) based v3msk starter kit
- Specify EtherAVB PHY IRQ now that GPIO support is present
R-Car D3 (r8a77995) based draak board
- Set better backlight levels
RZ/G2M (r8a774a1) SoC
- Correct hsusb reg size
RZ/G2E (r8a774c0) SoC
- Intial SoC DT
- Add: and SYS-DMAC controller, SCIF, HSCIF, INTC-EX
PFC, GPIO, Ethernet AVB, watchdog, secondary CA3 core, SDHI,
I2C, IIC-DVFS, IPMU, CAN, thermal, MSIOF, audio, PWM, display output,
USB2.0, USB-DMAC, HSUSB, USB3.0, IPMMU, PCIe, VIN and CSI-2 support
- A follow-up patch included in this pull-request enables DMA for SCIF2
so that DMA is enabled for all SCIF nodes
* tag 'renesas-arm64-dt-for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (44 commits)
arm64: dts: renesas: r8a77990: ebisu: Enable HS400 of SDHI3
arm64: dts: renesas: r8a77990: Enable DMA for SCIF2
arm64: dts: renesas: r8a774c0: Enable DMA for SCIF2
arm64: dts: renesas: r8a77990: ebisu: Fix backlight regulator numbering
arm64: dts: renesas: v3msk: specify EtherAVB PHY IRQ
arm64: dts: renesas: r8a77990-ebisu: use simple-audio-card
arm64: dts: renesas: r8a7796: remove BUSIF0 settings from rcar_sound,ssi
arm64: dts: renesas: r8a7795: remove BUSIF0 settings from rcar_sound,ssi
arm64: dts: renesas: ulcb-kf: add pcm3168 sound codec
arm64: dts: renesas: ulcb: add HDMI sound support
arm64: dts: renesas: ulcb: use audio-graph-card
arm64: dts: renesas: r8a7796: salvator-xs: Convert to new LVDS DT bindings
arm64: dts: renesas: r8a77990: Sort i2c nodes within soc node
arm64: dts: renesas: r8a77990: sort pciec0 node within soc node
arm64: dts: renesas: r8a774a1: Fix hsusb reg size
arm64: dts: renesas: r8a774c0: Add VIN and CSI-2 device nodes
arm64: dts: renesas: r8a774c0: Add PCIe device node
arm64: dts: renesas: r8a774c0: Connect RZ/G2E Audio-DMAC to IPMMU
arm64: dts: renesas: r8a774c0: Connect RZ/G2E AVB to IPMMU
arm64: dts: renesas: r8a774c0: Connect RZ/G2E SYS-DMAC to IPMMU
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The 'arm,armv8' compatible string is only for software models. It adds
little value otherwise and is inconsistently used as a fallback on some
platforms. Remove it from those platforms.
This fixes warnings generated by the DT schema.
Reported-by: Michal Simek <michal.simek@xilinx.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Chanho Min <chanho.min@lge.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Wei Xu <xuwei5@hisilicon.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Acked-by: Robert Richter <rrichter@cavium.com>
Acked-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Allwinner Fixes for 5.0
A couple of device tree fixes for the 5.0 cycle:
- Add missing clock-output-names for the osc24M clock on sun6i/A31
The Linux clock driver uses the device node as the clock name if
the property is missing. The node name was changed in 5.0-rc1,
breaking a subtle dependency in the sunxi-ng clock driver, and
renders Linux unable to completely boot up.
- Add alias for Ethernet controller on Beelink X2
This allows the bootloader to assign a deterministically generated
MAC address to it.
- Add property to enable USB VBUS regulator on OrangePi Win
The board had defined the constraints for the regulator, but was
missing the property to actually enable it.
* tag 'sunxi-fixes-for-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: a64: Fix USB OTG regulator
ARM: dts: sun8i: h3: Add ethernet0 alias to Beelink X2
ARM: dts: sun6i: Add clock-output-names to osc24M clock
arm64: dts: allwinner: a64: Fix the video engine compatible
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Amlogic fixes for v5.0-rc, round 2
- several fixups for the GPIO cd-inverted change
- IRQ trigger fixes for MAC IRQ
* tag 'amlogic-fixes-2.1' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
arm64: dts: meson: Fix mmc cd-gpios polarity
ARM: dts: meson8m2: mxiii-plus: mark the SD card detection GPIO active-low
ARM: dts: meson8b: ec100: mark the SD card detection GPIO active-low
ARM: dts: meson8b: odroidc1: mark the SD card detection GPIO active-low
arm: dts: meson: Fix IRQ trigger type for macirq
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Qualcomm ARM64 Fixes for 5.0-rc3
* Fix irq controller compatible for the MSM8996 platforms
* tag 'qcom-fixes-for-5.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
arm64: dts: add msm8996 compatible to gicv3
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Second Round of Renesas ARM Based SoC Fixes for v5.0
Enable DMA for SCIF2 on R-Car M3-W (r8a7796) and M3-n (r8a77965), and
(RZ/G2M) r8a774a1 SoCs.
This is was omitted from patches enabling DMA for other SCIF devices on the
same SoCs due to missing documentation. However, it is regarded as a fix
as arguably those patches claim to add this feature.
Per-SoC patches are provided to ease backporting of this fix as the kernel
version to be fixed is different for each SoC.
* tag 'renesas-fixes2-for-v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: renesas: r8a77965: Enable DMA for SCIF2
arm64: dts: renesas: r8a7796: Enable DMA for SCIF2
arm64: dts: renesas: r8a774a1: Enable DMA for SCIF2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
A CPUfreq driver, like the scpi driver used on Juno boards, which
provide the Energy Model with power cost information via the PM_OPP
of_dev_pm_opp_get_cpu_power() function, do need the
dynamic-power-coefficient (C) in the device tree.
Method used to obtain the C value:
C is computed by measuring energy (E) consumption of a frequency domain
(FD) over a 10s runtime (t) sysbench workload running at each Operating
Performance Point (OPP) affine to 1 or 2 CPUs of that FD while the other
CPUs of the system are hotplugged out.
By definition all CPUs of a FD have the the same micro-architecture. An
OPP is characterized by a certain frequency (f) and voltage (V) value.
The corresponding power values (P) are calculated by dividing the delta
of the E values between the runs with 2 and 1 CPUs by t.
With n data tuples (P, f, V), n equal to number of OPPs for this
frequency domain, we can solve C by:
P = Pstat + Pdyn
P = Pstat + CV²f
Cx = (Px - P1)/(Vx²fx - V1²f1) with x = {2, ..., n}
The C value is the arithmetic mean out of {C2, ..., Cn}.
Since DVFS is broken on Juno r1, no dynamic-power-coefficient
information has been added to its dts file.
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Quentin Perret <quentin.perret@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
Ezequiel Garcia
David Dai
Bjorn Andersson
Marc Gonzalez
Jeffrey Hugo
Stefan Wahren
James Morse
Ard Biesheuvel
Catalin Marinas
Kristina Martsenko
Harald Geyer
Jagan Teki
Carlo Caione
Lucas Stach
Faiz Abbas
Yogesh Narayan Gaur
Manivannan Sadhasivam
Greg Kroah-Hartman
Shawn Guo
Vincent Guittot
John Stultz
Linus Walleij
Arnd Bergmann
Rob Herring
Dietmar Eggemann