| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
sama5d3_xplained, sam9x5cm, sama5d2_ptc_ek and sama5d4_xplained nand
flashes have a common memory map. Even the nand memory partitions to
match our nand flash map available at:
http://www.at91.com/linux4sam/pub/Linux4SAM/SambaSubsections//demo_nandflash_map_lnx4sam5x.png
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
|
|
sam9x5cm, sama5d2_ptc_ek, sama5d3_xplained and sama5d4_xplained nand
flashes have a common memory map. Even the nand memory partitions to
match our nand flash map available at:
http://www.at91.com/linux4sam/pub/Linux4SAM/SambaSubsections//demo_nandflash_map_lnx4sam5x.png
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
|
|
The offsets for the bootloader environment and its redundant partition
were inverted. Fix the addresses to match our nand flash map available at:
http://www.at91.com/linux4sam/pub/Linux4SAM/SambaSubsections//demo_nandflash_map_lnx4sam5x.png
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
|
|
at91sam9x5cm comes with a 2Gb NAND flash. Fix the rootfs size to
match this limit.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
|
|
sama5d4_xplained comes with a 4Gb NAND flash. Increase the rootfs
size to match this limit.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
|
|
Add SD controller nodes for LD4, Pro4, sLD8, Pro5, and PXs2.
This is also used as an eMMC controller for LD4, Pro4, and sLD8.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This code is no longer used. Remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: David Lechner <david@lechnology.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
There is nothing arch specific about building dtb files other than their
location under /arch/*/boot/dts/. Keeping each arch aligned is a pain.
The dependencies and supported targets are all slightly different.
Also, a cross-compiler for each arch is needed, but really the host
compiler preprocessor is perfectly fine for building dtbs. Move the
build rules to a common location and remove the arch specific ones. This
is done in a single step to avoid warnings about overriding rules.
The build dependencies had been a mixture of 'scripts' and/or 'prepare'.
These pull in several dependencies some of which need a target compiler
(specifically devicetable-offsets.h) and aren't needed to build dtbs.
All that is really needed is dtc, so adjust the dependencies to only be
dtc.
This change enables support 'dtbs_install' on some arches which were
missing the target.
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Paul Burton <paul.burton@mips.com>
Acked-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Michal Marek <michal.lkml@markovi.net>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: linux-kbuild@vger.kernel.org
Cc: linux-snps-arc@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: uclinux-h8-devel@lists.sourceforge.jp
Cc: linux-mips@linux-mips.org
Cc: nios2-dev@lists.rocketboards.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-xtensa@linux-xtensa.org
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
mvebu soc for 4.20 (part 1)
- use dt_fixup to provide fallback for enable-method for Armada XP
- document the marvell,prestera compatible string
- update Thomas Petazzoni email in MAINTAINERS file
* tag 'mvebu-soc-4.20-1' of git://git.infradead.org/linux-mvebu:
dt-bindings: marvell,prestera: Add common compatible string
MAINTAINERS: replace free-electrons.com by bootlin.com for Thomas Petazzoni
ARM: mvebu: use dt_fixup to provide fallback for enable-method
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
i.MX SoC update for 4.20:
- Add ipg clock support in MMDC driver for registers access, so that
we will be safe even if the clock is not turned on by firmware.
- Register pm_power_off handler to provide power off support for iMX6
based boards with external PMIC.
- Add platform code support for i.MX 6ULZ SoC which is a derivative of
i.MX6ULL with some modules removed.
* tag 'imx-soc-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx: add i.mx6ulz msl support
ARM: imx6: register pm_power_off handler if "fsl,pmic-stby-poweroff" is set
ARM: imx: add mmdc ipg clock operation for mmdc
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Devicetree changes for omap variants
This branch contains a series of improvments for omap3-gta04 phone,
and a series of clean-up for am335x to remove the deprecated phy_id
property.
The rest is to configure am57xx-idk boards for leds, load trigger,
and smps, am3517-evm audio configuration, beaglebone hdmi cec support,
coresight binding update, and fixes for i2c and spi warnings.
* tag 'omap-for-v4.20/dt-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (70 commits)
ARM: dts: add omap3-gta04a5one to Makefile
ARM: dts: omap3-gta04: add pulldown/up settings for twl4030 gpio
ARM: dts: am335x-boneblack: add cec support
ARM: dts: am3517-evm: Add support for UI board and Audio
ARM: dts: gta04: add serial console wakeup irq
ARM: dts: am57xx-idk-common: Hook smps12 regulator as cpu vdd-supply
ARM: dts: omap: Update coresight bindings for hardware ports
ARM: dts: ti: Fix SPI and I2C bus warnings
ARM: dts: dra62x-j5eco-evm: get rid of phy_id property
ARM: dts: dm8148-t410: get rid of phy_id property
ARM: dts: dm8148-evm: get rid of phy_id property
ARM: dts: am57xx-cl-som-am57x: get rid of phy_id property
ARM: dts: am57xx-idk-common: get rid of phy_id property
ARM: dts: dra7-evm: get rid of phy_id property
ARM: dts: dra71-evm: get rid of phy_id property
ARM: dts: dra72-evm-revc: get rid of phy_id property
ARM: dts: dra72-evm: get rid of phy_id property
ARM: dts: dra76-evm: get rid of phy_id property
ARM: dts: am437x-cm-t43: get rid of phy_id property
ARM: dts: am437x-gp-evm: get rid of phy_id property
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
mvebu dt for 4.20 (part 1)
- updates the armada-xp-98dx3236 SoC and related boards to use the new
style dts bindings for nand
- add db-88f6820-amc board: plugin card for some of Marvell's switch
development kits
- fix SPI and I2C bus warnings coming with the new checks in dtc
- add new compatible string "marvell,prestera" to the armada-xp-98dx*
- fix sdhci supply property name on the clearfog (the '-supply' suffix
was missing)
* tag 'mvebu-dt-4.20-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: clearfog: fix sdhci supply property name
ARM: dts: mvebu: add "marvell,prestera" to PP nodes
ARM: dts: marvell: Fix SPI and I2C bus warnings
ARM: dts: mvebu: Add device tree for db-88f6820-amc board
ARM: dts: mvebu: db-xc3-24g4: use new style nand binding
ARM: dts: mvebu: db-dxbc2: use new style nand binding
ARM: dts: mvebu: 98dx3236: Rename nand controller node
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
i.MX device tree update for 4.20:
- New board support: Engicam's i.Core MX6 CPU module v1.5; ConnectCore
6UL Single Board Computer (SBC) Pro; i.MX6 ULZ based EVK board.
- Add Add SFF interface support for vf610-zii board.
- Disable unneeded devices like VPU and internal watchdog for imx51-zii
boards.
- Add 'no-sdio' and 'no-sd' property for vf610-zii-cfu1 board.
- Improve i.MX6 SLL GPIO support by adding gpio-ranges property and
clocks information.
- Update iomux header for i.MX7 Solo and i.MX6 ULL.
- Enable GPIO buttons as wakeup source for imx7d-sdb and imx6sx-sdb.
- Add GPIO keys and egalax touch screen support for imx6qdl-sabreauto.
- Switch to use SPDX-License-Identifier for more boards - vf610-twr,
imx7s-warp, Engicam boards.
- Add device tree bindings of 'fsl,pmic-stby-poweroff' property and add
the support for i.MX6 RIoTboard.
- DTC has new checks for SPI buses which will be landed on 4.20.
A patch from Rob to fix those 100+ warnings on i.MX boards. (Thanks!)
- Switch i.MX7 device tree to use updated coresight binding for
hardware ports.
- Misc small or random update and cleanup.
* tag 'imx-dt-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (50 commits)
ARM: dts: imx: add i.mx6ulz and i.mx6ulz 14x14 evk support
dt-bindings: arm: add compatible for i.MX6ULZ 14x14 EVK board
ARM: dts: imx53-ppd: Remove 'num-chipselects' property
ARM: dts: vf610-twr: Switch to SPDX identifier
ARM: dts: vf: Switch to SPDX identifier
ARM: dts: imx6qdl-zii-rdu2: Disable the internal RTC
ARM: dts: imx51-zii-rdu1: Fix the rtc compatible string
ARM: dts: imx6ul: use nvmem-cells for cpu speed grading
ARM: dts: imx: Fix SPI bus warnings
ARM: dts: imx7: Update coresight binding for hardware ports
ARM: dts: vf610-zii-cfu1: Pass the 'no-sd' property
ARM: dts: vf610-zii-cfu1: Pass the 'no-sdio' property
ARM: dts: imx51-zii-scu2-mezz: Disable the internal watchdog
ARM: dts: imx51-zii-scu2-mezz: Disable VPU
ARM: dts: imx51-zii-scu3-esb: Disable VPU
ARM: dts: imx51: Add label for VPU node
ARM: dts: imx6ull: update vdd_soc voltage for 900MHz operating point
ARM: dts: imx6ul: Add DTS for ConnectCore 6UL SBC Pro
ARM: dts: imx6: RIoTboard provide standby on power off option
dt-bindings: imx6q-clock: add new fsl,pmic-stby-poweroff property
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Qualcomm Device Tree Changes for v4.20
* Fix IRQ constants usage on MSM8974
* Add led, gpio-button, sdcc, and pcie nodes for IPQ8064
* Move/cleanup common nodes for IPQ8064
* Add i2c sensor nodes for MSM8974 Hammerhead
* Fixes for SAW, kpss, opp, pci range, and space/tab on IPQ4019
* Update coresight bindings
* tag 'qcom-dts-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
ARM: dts: qcom: Update coresight bindings for hardware ports
ARM: dts: qcom-msm8974: change invalid flag IRQ NONE to valid value
ARM: dts: qcom: ipq4019: fix space vs tab indenting inside qcom-ipq4019.dtsi
ARM: dts: qcom: ipq4019: fix PCI range
ARM: dts: qcom: ipq4019: fix cpu0's qcom,saw2 reg value
ARM: dts: qcom: ipq4019: add cpu operating points for cpufreq support
ARM: dts: qcom: ipq4019: use v2 of the kpss bringup mechanism
ARM: dts: qcom: msm8974-hammerhead: add device tree bindings for ALS / proximity
ARM: dts: qcom: msm8974-hammerhead: add device tree bindings for mpu6515
ARM: dts: qcom: Add led and gpio-button nodes to ipq8064 boards
ARM: dts: qcom: Move common nodes to ipq8064-v.1.0.dtsi
ARM: dts: qcom: Add sdcc nodes for ipq8064
ARM: dts: qcom: Add pcie nodes for ipq8064
ARM: dts: qcom-msm8974: change invalid flag IRQ NONE to valid value
ARM: dts: qcom-msm8974: use named constant for interrupt flag NONE
ARM: dts: qcom-msm8974: use named constant for interrupt flag LEVEL HIGH
ARM: dts: qcom-msm8974: use named constant for interrupt flag EDGE RISING
ARM: dts: qcom-msm8974: use named constant for interrupt type GIC_SPI
ARM: dts: qcom-msm8974: use named constant for interrupt type GIC_PPI
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Actions Semi arm based SoC DT for v4.20
This updates SPDX headers for remaining files.
* tag 'actions-arm-dt-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-actions:
ARM: dts: owl: Convert to new-style SPDX license identifiers
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Allwinner DT changes for 4.20
Our usual bunch of DT patches for the Allwinner arm32 SoCs.
The most notable changes are:
- Support for the video decoding / encoding engine on the
A10s/A13/A20/A33
- IR support for the A83t
- SATA support for the R40
* tag 'sunxi-dt-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun9i: Fix I2C bus warnings
ARM: dts: sunxi: Fix I2C bus warnings
ARM: dts: sun8i-a33: Add Video Engine and reserved memory nodes
ARM: dts: sun7i-a20: Add Video Engine and reserved memory nodes
ARM: dts: sun5i: Add Video Engine and reserved memory nodes
ARM: dts: sun8i: sun8i-r40-bananapi-m2-ultra: enable AHCI
ARM: dts: sun8i: r40: add sata node
ARM: dts: sunxi: Don't use cd-inverted in sun8i-r40-bananapi-m2-ultra
ARM: dts: sun8i: a83t: bananapi-m3: Enable IR controller
ARM: dts: sun8i: a83t: Add support for the cir interface
ARM: dts: sun8i: a83t: Add the cir pin for the A83T
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Allwinner H3 and H5 DT additions for 4.20
This is our usual H3/H5 pull request
The most notable changes are:
- the video decoding / encoding unit is finally enabled on the H3
- Mali support for the H5
- New boards: BananaPi M2+ v1.2, Orange Pi Zero Plus 2 H3 support
* tag 'sunxi-h3-h5-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sunxi: h3-h5: Add Bananapi M2+ v1.2 device trees
ARM: dts: sun8i-h3: Add Video Engine and reserved memory nodes
arm64: dts: allwinner: h5: Add device tree for Bananapi M2 Plus H5
ARM: dts: sun8i: h3: Split out non-SoC-specific parts of Bananapi M2 Plus
ARM: dts: sun8i: h3: bpi-m2-plus: Fix address for external RGMII Ethernet PHY
ARM: dts: sun8i: h3-h5: ir register size should be the whole memory block
arm64: dts: allwinner: h5: Add device node for Mali-450 GPU
ARM: dts: sun8i: Add initial Orangepi Zero Plus 2 H3 support
nvmem: sunxi-sid: add support for H5's SID controller
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Enable the USB3 and USB2 phys implemented in UniPhier SoCs.
These phys are necessary for dwc3 and ehci controllers driving
the USB ports on Pro4 and PXs2 SoCs.
Since the USB host drivers are already built-in, so only the phy
driver are missing to allow booting with USB devices.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Olof writes:
"ARM: SoC fixes
A handful of fixes that have been coming in the last couple of weeks:
- Freescale fixes for on-chip accellerators
- A DT fix for stm32 to avoid fallback to non-DMA SPI mode
- Fixes for badly specified interrupts on BCM63xx SoCs
- Allwinner A64 HDMI was incorrectly specified as fully compatble with R40
- Drive strength fix for SAMA5D2 NAND pins on one board"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: stm32: update SPI6 dmas property on stm32mp157c
soc: fsl: qe: Fix copy/paste bug in ucc_get_tdm_sync_shift()
soc: fsl: qbman: qman: avoid allocating from non existing gen_pool
ARM: dts: BCM63xx: Fix incorrect interrupt specifiers
MAINTAINERS: update the Annapurna Labs maintainer email
ARM: dts: sun8i: drop A64 HDMI PHY fallback compatible from R40 DT
ARM: dts: at91: sama5d2_ptc_ek: fix nand pinctrl
|
|
Add SD card write-protect pin configuration to be sure that it will be
properly pulled down to indicate write access.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
"S3C2410 PM Suspend Memory CRC" feature (controlled by
SAMSUNG_PM_CHECK config option) is incompatible with highmem
(uses phys_to_virt() instead of proper mapping) which is used by
the majority of Exynos boards. The issue manifests itself in OOPS
on affected boards, i.e. on Odroid-U3 I got the following one:
Unable to handle kernel paging request at virtual address f0000000
pgd = 1c0f9bb4
[f0000000] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
[<c0458034>] (crc32_le) from [<c0121f8c>] (s3c_pm_makecheck+0x34/0x54)
[<c0121f8c>] (s3c_pm_makecheck) from [<c0121efc>] (s3c_pm_run_res+0x74/0x8c)
[<c0121efc>] (s3c_pm_run_res) from [<c0121ecc>] (s3c_pm_run_res+0x44/0x8c)
[<c0121ecc>] (s3c_pm_run_res) from [<c01210b8>] (exynos_suspend_enter+0x64/0x148)
[<c01210b8>] (exynos_suspend_enter) from [<c018893c>] (suspend_devices_and_enter+0x9ec/0xe74)
[<c018893c>] (suspend_devices_and_enter) from [<c0189534>] (pm_suspend+0x770/0xc04)
[<c0189534>] (pm_suspend) from [<c0186ce8>] (state_store+0x6c/0xcc)
[<c0186ce8>] (state_store) from [<c09db434>] (kobj_attr_store+0x14/0x20)
[<c09db434>] (kobj_attr_store) from [<c02fa63c>] (sysfs_kf_write+0x4c/0x50)
[<c02fa63c>] (sysfs_kf_write) from [<c02f97a4>] (kernfs_fop_write+0xfc/0x1e4)
[<c02f97a4>] (kernfs_fop_write) from [<c027b198>] (__vfs_write+0x2c/0x140)
[<c027b198>] (__vfs_write) from [<c027b418>] (vfs_write+0xa4/0x160)
[<c027b418>] (vfs_write) from [<c027b5d8>] (ksys_write+0x40/0x8c)
[<c027b5d8>] (ksys_write) from [<c0101000>] (ret_fast_syscall+0x0/0x28)
Add PLAT_S3C24XX, ARCH_S3C64XX and ARCH_S5PV210 dependencies to
SAMSUNG_PM_CHECK config option to hide it on Exynos platforms.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Qualcomm ARM Based defconfig Updates for v4.20
* Enable MAILBOX
* tag 'qcom-defconfig-for-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
ARM: qcom_defconfig: Enable MAILBOX
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Merge -rc6 in, for two reasons:
1) Resolve a trivial conflict in the blk-mq-tag.c documentation
2) A few important regression fixes went into upstream directly, so
they aren't in the 4.20 branch.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* tag 'v4.19-rc6': (780 commits)
Linux 4.19-rc6
MAINTAINERS: fix reference to moved drivers/{misc => auxdisplay}/panel.c
cpufreq: qcom-kryo: Fix section annotations
perf/core: Add sanity check to deal with pinned event failure
xen/blkfront: correct purging of persistent grants
Revert "xen/blkfront: When purging persistent grants, keep them in the buffer"
selftests/powerpc: Fix Makefiles for headers_install change
blk-mq: I/O and timer unplugs are inverted in blktrace
dax: Fix deadlock in dax_lock_mapping_entry()
x86/boot: Fix kexec booting failure in the SEV bit detection code
bcache: add separate workqueue for journal_write to avoid deadlock
drm/amd/display: Fix Edid emulation for linux
drm/amd/display: Fix Vega10 lightup on S3 resume
drm/amdgpu: Fix vce work queue was not cancelled when suspend
Revert "drm/panel: Add device_link from panel device to DRM device"
xen/blkfront: When purging persistent grants, keep them in the buffer
clocksource/drivers/timer-atmel-pit: Properly handle error cases
block: fix deadline elevator drain for zoned block devices
ACPI / hotplug / PCI: Don't scan for non-hotplug bridges if slot is not bridge
drm/syncobj: Don't leak fences when WAIT_FOR_SUBMIT is set
...
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Right now the stage2 page table for a VM is hard coded, assuming
an IPA of 40bits. As we are about to add support for per VM IPA,
prepare the stage2 page table helpers to accept the kvm instance
to make the right decision for the VM. No functional changes.
Adds stage2_pgd_size(kvm) to replace S2_PGD_SIZE. Also, moves
some of the definitions in arm32 to align with the arm64.
Also drop the _AC() specifier constants wherever possible.
Cc: Christoffer Dall <cdall@kernel.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Allow the arch backends to perform VM specific initialisation.
This will be later used to handle IPA size configuration and per-VM
VTCR configuration on arm64.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <cdall@kernel.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Switch to the new hardware port bindings for coresight
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
We want the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
i.MX6ULZ is new SoC of i.MX6 family, compared to i.MX6ULL,
it removes below modules:
- UART5/UART6/UART7/UART8;
- PWM5/PWM6/PWM7/PWM8;
- eCSPI3/eCSPI4;
- CAN1/CAN2;
- FEC1/FEC2;
- I2C3/I2C4;
- EPIT2;
- LCDIF;
- GPT2;
- ADC1;
- TSC;
This patch adds support for i.MX6ULZ and i.MX6ULZ 14x14 EVK
board.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The i.MX 6ULZ processor is a high-performance, ultra
cost-efficient consumer Linux processor featuring an
advanced implementation of a single Arm® Cortex®-A7 core,
which operates at speeds up to 900 MHz.
This patch adds basic MSL support for i.MX6ULZ, the
i.MX6ULZ has same soc_id as i.MX6ULL, and SRC_SBMR2 bit[6]
is to differentiate i.MX6ULZ from i.MX6ULL, 1'b1 means
i.MX6ULZ and 1'b0 means i.MX6ULL.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The 'num-chipselects' property is not a valid property according
to Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt, so
let's remove it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Bananapi released an updated revision of the H3/H5 based Bananapi M2+.
Version 1.2 enables voltage control for the CPU's regulator by using
a GPIO line to toggle a MOSFET that can change the effective resistance
value in the regulator's feedback network.
This patch adds a common .dtsi file for this new revision, which
includes the original common sunxi-bananapi-m2-plus.dtsi file, and
adds the GPIO-controlled regulator and a cpu-supply reference. H3
and H5 variant dts files are added as well.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
This adds nodes for the Video Engine and the associated reserved memory
for the H3. Up to 96 MiB of memory are dedicated to the CMA pool.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Three more variants of the Bananapi M2 Plus have been introduced. One
with the H5 instead of the H3, another with the H2+ instead, and the
last with the H3 but with WiFi and eMMC removed.
All these variants use the same board. This patch splits out the
non-SoC-specific parts of the device tree, so that they can be shared
among all the variants. The original Bananapi M2 Plus has been renamed
to Bananapi M2 Plus H3.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The external RTL8211E RGMII Ethernet PHY is configured via external
resistors to use the address 0x1. The 0x0 address is a broadcast address
for this family of PHYs, and should not be used explicitly.
Fixes: 8c7ba536e709 ("ARM: sun8i: bananapi-m2-plus: Enable dwmac-sun8i")
Fixes: 4904337fe34f ("ARM: dts: sunxi: Restore EMAC changes (boards)")
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The size of the register should be the size of the whole memory block,
not just the registers, that are needed.
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
Orangepi Zero Plus 2 is an open-source single-board computer, available in two
Allwinner SOC variants, H3 and H5. We add support for H3 variant here, as the
H5 is already supported by sun50i-h5-orangepi-zero-plus2.dts.
H3 Orangepi Zero Plus 2 has:
- Quad-core Cortex-A7
- 512MB DDR3
- microSD slot and 8GB eMMC
- Debug TTL UART
- HDMI
- Wifi + BT
- OTG + power supply
Signed-off-by: Diego Rondini <diego.rondini@kynetics.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
|
|
Looks like we still have two instances of phy_handle that did not
get update by Grygorii's series. Let's replace these too with
standard phy-handle.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Neeraj Dantu <dantuguf14105@gmail.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add support for Moxa UC-2101 open platform
The UC-2101 computing platform is designed for industrial embedded
data acquisition and processing applications.
The features of UC-2101 are:
* eMMC
* SPI flash
* 1x LAN
* 1x RS-232/422/485 ports, software-selectable
* EEPROM
* TPM 2.0
* Watchdog
* RTC
* User gpio-keys
* User LEDs
* User button
Signed-off-by: Wes Huang (黃淵河) <wes.huang@moxa.com>
Signed-off-by: Fero JD Zhou (周俊達) <FeroJD.Zhou@moxa.com>
Signed-off-by: SZ Lin (林上智) <sz.lin@moxa.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The UC-2100 series consists many boards with different peripheral
devices and wireless modules, hence we fetch common items and
create a common dtsi file to increase reusability. All boards in
UC-2100 series will include this common dtsi file.
Signed-off-by: Wes Huang (黃淵河) <wes.huang@moxa.com>
Signed-off-by: Fero JD Zhou (周俊達) <FeroJD.Zhou@moxa.com>
Signed-off-by: SZ Lin (林上智) <sz.lin@moxa.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Renesas ARM Based SoC Drivers Updates for v4.20
* Convert to SPDX identifiers
* R-Car V3M (r8a77970) and V3H (r8a77980): Document Timer Unit (TMU) bindings
* RZ/G1N (r8a7744) and RZ/G1C (r8a77470) SoCs:
- Document APMU and SMP enable method
* RZ/G2M (r8a74a1), RZ/G1N (r8a7744) and RZ/G2E (r8a774c0) SoCs:
- Add reset support
- Add sysc support
* RZ/G2M (r8a774a1), RZ/G2E (r8a774c0) and RZ/A2M (r7s9210) SoCs:
- Add support for identifying SoC
* RZ/A2M (r7s9210) SoC:
- Add basic SoC setup support
* tag 'renesas-drivers-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (21 commits)
dt-bindings: apmu: Document r8a7744 support
dt-bindings: timer: renesas: tmu: document R8A779{7|8}0 bindings
dt-bindings: apmu: Document r8a77470 support
soc: renesas: rcar-rst: Add support for RZ/G1N
dt-bindings: reset: rcar-rst: Document r8a7744 reset module
soc: renesas: rcar-sysc: Add r8a7744 support
dt-bindings: power: rcar-sysc: Add r8a7744 power domain index macros
dt-bindings: power: rcar-sysc: Document r8a7744 SYSC binding
soc: renesas: rcar-rst: Add support for RZ/G2E
dt-bindings: reset: rcar-rst: Document r8a774c0 rst
soc: renesas: rcar-sysc: Add r8a774c0 support
dt-bindings: power: rcar-sysc: Document r8a774c0 sysc
dt-bindings: power: Add r8a774c0 SYSC power domain definitions
soc: renesas: Identify RZ/G2E
soc: renesas: convert to SPDX identifiers
soc: renesas: rcar-rst: Add support for RZ/G2M
soc: renesas: rcar-sysc: Add r8a774a1 support
dt-bindings: power: Add r8a774a1 SYSC power domain definitions
soc: renesas: identify RZ/A2
ARM: shmobile: Add basic RZ/A2 SoC support
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Renesas ARM Based SoC Updates for v4.20
* Rework the PMIC IRQ line quirk to use DT rather than hard coded topology
* Convert to SPDX identifiers
* Convert to using %pOFn instead of device_node.name
* Remove the no longer needed ARCH_SHMOBILE Kconfig symbol
* RZ/G1N (r8a7744) SoC: Add basic SoC and debug-ll support
* R-Car H1 (r8a7779) SoC: remove unused includes
* tag 'renesas-arm-soc-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Rework the PMIC IRQ line quirk
ARM: debug-ll: Add support for r8a7744
ARM: shmobile: r8a7744: Basic SoC support
ARM: shmobile: convert to SPDX identifiers
ARM: shmobile: Convert to using %pOFn instead of device_node.name
ARM: shmobile: Remove the ARCH_SHMOBILE Kconfig symbol
ARM: shmobile: r8a7779: Remove unused includes
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Use the for_each_of_cpu_node iterator to iterate over cpu nodes. This
has the side effect of defaulting to iterating using "cpu" node names in
preference to the deprecated (for FDT) device_type == "cpu".
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-renesas-soc@vger.kernel.org
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Checking for "/cpus" node is not necessary as of_get_cpu_node() will fail
later on anyways. The call to of_find_node_by_path() also leaks a
reference. So just remove the check.
Cc: Russell King <linux@armlinux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Use the for_each_of_cpu_node iterator to iterate over cpu nodes. This
has the side effect of defaulting to iterating using "cpu" node names in
preference to the deprecated (for FDT) device_type == "cpu".
Cc: Russell King <linux@armlinux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Since SMPS10 and OTG cable detection extcon are described here, and
work to enable OTG power when an OTG cable is plugged in, we can
define OTG mode in the controller (which is disabled by default in
omap5.dtsi).
Tested on OMAP5EVM and Pyra.
Suggested-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add ti,syscon-unaligned-access property to PCIe RC nodes to set
appropriate bits in CTRL_CORE_SMA_SW_7 register to enable workaround for
errata i870.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
Tudor Ambarus
Masahiro Yamada
Bartosz Golaszewski
Rob Herring
Arnd Bergmann
Kunihiko Hayashi
Ingo Molnar
Greg Kroah-Hartman
Krzysztof Kozlowski
Bartlomiej Zolnierkiewicz
Jens Axboe
Suzuki K Poulose
Anson Huang
Fabio Estevam
Chen-Yu Tsai
Paul Kocialkowski
Philipp Rossak
Diego Rondini
Tony Lindgren
SZ Lin (林上智)
H. Nikolaus Schaller
Vignesh R