| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Scatter-gather lists passed to UpdateCapsule() should be cleaned
from the D-cache to ensure that they are visible to the CPU after a
warm reboot before the MMU is enabled. On ARM and arm64 systems, this
implies a D-cache clean by virtual address to the point of coherency.
However, due to the fact that the firmware itself is not able to map
physical addresses back to virtual addresses when running under the OS,
this must be done by the caller.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
Driver changes for omaps for genpd for v5.11 merge window
This series of changes allows booting am335x with genpd and
device tree data without the legacy platform data. Also at
least am437x can be booted with gendp with power domain and
dts data. The SoC specific dts changes will be a separate
pull request.
We need the following driver changes merged before the dts
changes can be done:
- platform code needs a few improvments to probe l4_wkup first
for clocks, and to bail out when there is no platform data
- ti-sysc driver needs a non-urgent fix for asserting rstctrl
reset only after disabling the clocks, to probe modules with
no known control registers, and added quirk handling for gpmc
devices
- omap-prm driver needs a non-urgent fix for reset status bit,
support added for pm_clk, and then we add the rest of am335x
power domain data
- clock driver for am335x needs to keep l3_main clock enabled
with genpd for suspend and resume to work
- wkup_m3 remoteproc driver needs support added for reset
control if available instead of the legacy pdata callbacks
- pm33xx driver needs PM runtime support added for genpd
The am335x specific driver changes for the clock, wkup_m3,
pm33xx and remoteproc drivers are quite trivial and have not
caused merge conflicts in Linux next. I did not get acks for
these changes except from Santosh but had already pushed out
the branch already at that point. So I've added the related
driver maintainers to Cc.
* tag 'omap-for-v5.11/genpd-drivers-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
remoteproc/wkup_m3: Use reset control driver if available
soc: ti: pm33xx: Enable basic PM runtime support for genpd
soc: ti: omap-prm: am3: add genpd support for remaining PRM instances
soc: ti: omap-prm: Add pm_clk for genpd
clk: ti: am33xx: Keep am3 l3 main clock always on for genpd
bus: ti-sysc: Implement GPMC debug quirk to drop platform data
bus: ti-sysc: Support modules without control registers
ARM: OMAP2+: Probe PRCM first to probe l4_wkup with simple-pm-bus
ARM: OMAP2+: Check for inited flag
bus: ti-sysc: Assert reset only after disabling clocks
soc: ti: omap-prm: Do not check rstst bit on deassert if already deasserted
bus: ti-sysc: Fix bogus resetdone warning on enable for cpsw
bus: ti-sysc: Fix reset status check for modules with quirks
ARM: OMAP2+: Fix missing select PM_GENERIC_DOMAINS_OF
ARM: OMAP2+: Fix location for select PM_GENERIC_DOMAINS
Link: https://lore.kernel.org/r/pull-1606806458-694517@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
arm64: dts: amlogic updates for v5.11, round 2
- audio support for several more boards
- PHY timing fixes
* tag 'amlogic-dt64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
arm64: dts: meson: add i2c3/rtc nodes and vrtc alias to GT-King/GT-King-Pro
arm64: dts: meson: g12b: w400: fix PHY deassert timing requirements
arm64: dts: meson: g12a: x96-max: fix PHY deassert timing requirements
ARM: dts: meson: fix PHY deassert timing requirements
arm64: dts: meson: fix PHY deassert timing requirements
arm64: dts: meson: g12b: odroid-n2: fix PHY deassert timing requirements
arm64: dts: meson: minor fixups for Khadas VIM/VIM2 dts
arm64: dts: meson: add audio playback to wetek-play2
arm64: dts: meson: add audio playback to wetek-hub
arm64: dts: meson: add audio playback to odroid-c2
arm64: dts: meson: add audio playback to nanopi-k2
arm64: dts: meson: add audio playback to khadas-vim2
arm64: dts: meson: add audio playback to khadas-vim
arm64: dts: meson: add audio playback to a95x
arm64: dts: meson-axg: add GE2D node
Link: https://lore.kernel.org/r/7ho8j4gkxo.fsf@baylibre.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Samsung DTS ARM changes for v5.11, part three
1. S3C bindings and DTS cleanup,
2. Correct the clock rates for SPI0 in Artik 5 which is a fix for recently
introduced Ethernet on SPI on Artik 5 board.
* tag 'samsung-dt-5.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Reduce assigned-clocks entries for SPI0 on Artik5 board
ARM: dts: s3c6410: correct SMDK6410 board compatible
ARM: dts: s3c24xx: add SMDK2416 board compatible
dt-bindings: arm: samsung: document S3C6410-based boards binding
dt-bindings: arm: samsung: document SMDK2416 board binding
Link: https://lore.kernel.org/r/20201207074528.4475-2-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Veyron backlight fix, another fix for dtbs-check and some additions
to the rk3288-based VMARC boards.
* tag 'v5.11-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Add SDIO0 node for VMARC SOM
ARM: dts: rockchip: Add rtc node for VMARC SOM
ARM: dts: rockchip: rename wdt nodename to watchdog on rv1108
ARM: dts: rockchip: Remove 0 point from brightness-levels on rk3288-veyron
Link: https://lore.kernel.org/r/4582475.GXAFRqVoOG@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
AT91 DT for 5.11 #2:
- switch to new TCB PWM bindings
- rework ADC bindings
- fix sama5d2 securam and can1
* tag 'at91-dt-5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: at91: sama5d2: fix CAN message ram offset and size
ARM: dts: at91: sama5d2: map securam as device
ARM: dts: at91: sam9x60ek: remove bypass property
ARM: dts: at91: remove deprecated ADC properties
ARM: dts: at91: at91sam9rl: fix ADC triggers
ARM: dts: at91: sama5d3: use proper ADC compatible
ARM: dts: at91: kizbox: switch to new pwm-atmel-tcb binding
Link: https://lore.kernel.org/r/20201206013840.GA627225@piout.net
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
i.MX device tree update for 5.11:
- New board support: imx6dl-alti6p, imx6dl-lanmcu, mx6qp-prtwd3,
imx6ul-phytec-segin and imx7d-flex-concentrator.
- Fix schema warnings for pwm-leds, watchdog and GPIO hog devices.
- A few patches from Krzysztof Kozlowski to correct compatibles for
i.MX6/7 boards.
- A series from Matthias Schiffer to polish imx7-mba7 board support.
- Update i.MX6/7 device trees for fsl,stop-mode support.
- Correct fsl,rcpm-wakeup of LS1021A to get flextimer wake-up work.
- A series of patch from Stefan Riedmueller to update phytec and segin
devices.
- Other small and random changes.
* tag 'imx-dt-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (40 commits)
ARM: dts: imx28: Fix label name for L2 switch
ARM: dts: add Protonic WD3 board
ARM: dts: imx6qdl-kontron-samx6i: increase i2c-frequency
ARM: dts: imx7: add support for kamstrup flex concentrator
ARM: dts: ls1021a: update calibration table for TMU module
ARM: dts: ls1021a: fix rcpm failed to claim resource
ARM: dts: ls1021a: fix flextimer failed to wake system
ARM: dts: imx50-kobo-aura: Enable eKTF2132 touchscreen
ARM: dts: imx: Change flexcan node name to "can"
ARM: dts: imx6q-pico: fix board compatibles
ARM: dts: add Van der Laan LANMCU board
ARM: dts: add Altesco I6P board
ARM: dts: imx6ul: segin: peb-av-02: Mark stmpe touch as wakeup-source
ARM: dts: imx6ul: phytec: Add support for optional PEB-AV-02 LCD adapter
ARM: dts: imx6ul: segin: Add phyBOARD-Segin with eMMC phyCORE-i.MX6UL
ARM: dts: imx50-kobo-aura: Add 'grp' suffix to pinctrl node names
ARM: dts: imx: add usb alias
ARM: dts: imx6/7: sync fsl,stop-mode with current flexcan driver
ARM: dts: imx: Fix schema warnings for pwm-leds
ARM: dts: imx7s-warp: correct vendor in compatible to Element14
...
Link: https://lore.kernel.org/r/20201202142717.9262-4-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Samsung DTS ARM changes for v5.11, part two
1. Add devicetree of Samsung Galaxy Note 10.1 tablets
(GT-N8010/GT-N8013), called P4 Note. These are quite old but
still functional devices, based on Exynos4412.
2. Minor cleanups in Odroid XU3 Ethernet.
3. Minor fixes: ADC io-channel-ranges and P4 Note touchscreen GPIO
polarity.
* tag 'samsung-dt-5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: switch Atmel mxt reset GPIO to active low on P4 Note
ARM: dts: s5pv210: Drop unneeded io-channel-ranges property in Aries
ARM: dts: s5pv210: Drop incorrect use of io-channel-ranges property
ARM: dts: exynos: Drop incorrect use of io-channel-ranges
ARM: dts: exynos: add Samsung's Exynos4412-based P4 Note boards
dt-bindings: arm: samsung: document bindings for P4 Note family board
ARM: dts: exynos: Add an alias for the Ethernet interface on Odroid XU3
ARM: dts: exynos: Fix Ethernet interface description on Odroid XU3
Link: https://lore.kernel.org/r/20201201204404.22675-2-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
ARM: dts: Keystone DTS update for v5.11
- HDMI Support
- Analog Audio data support
* tag 'keystone_dts_for_5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: dts: keystone-k2g-evm: add HDMI and analog audio data
Link: https://lore.kernel.org/r/1606851472-26593-1-git-send-email-santosh.shilimkar@oracle.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Qualcomm DT updates for 5.11
This adds support for SD card, WiFi, LED, touchscreeni, touchkey and
fuel gauge to the Samsung Galaxy S5. Nexus 5 also gains fuel gauge
support.
Finally IPQ6016 gains support for the QPIC NAND controller.
* tag 'qcom-dts-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
arm64: dts: ipq6018: Add the QPIC peripheral nodes
ARM: dts: qcom-pma8084: Drop incorrect use of io-channel-ranges
ARM: dts: qcom: msm8974-lge-nexus5: Add fuel gauge
ARM: dts: qcom: msm8974-klte: Add fuel gauge
ARM: dts: qcom: msm8974-klte: Add support for SD card
ARM: dts: qcom: msm8974-klte: Add support for wifi
ARM: dts: qcom: msm8974-klte: Add gpio expander chip
ARM: dts: qcom: msm8974-klte: Add support for led
ARM: dts: qcom: msm8974-klte: Add support for touchscreen
ARM: dts: qcom: msm8974-klte: Add support for touchkey
ARM: dts: qcom: msm8974-klte: Merge pinctrl nodes
Link: https://lore.kernel.org/r/20201130190148.345302-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
mvebu dt for 5.11 (part 1)
- Add support for MikroTik CRS3xx switches
- Add support for RD-AC3X-48G4X2XL board : Armada 382 SoC connected
to Prestera AC3X ASIC through PCI
- Clean-up kirkwood device tree: replace "ok" by "okay"
- Improve device tree for PCA953x gpio expander nodes
- Use compliant node name for USB3 on armada 375
- 98dx3236 SoCs:
- remove non-existent i2c1
- add i2c0 pinctrl information
- Improve device tree for Turris Omnia
* tag 'mvebu-dt-5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
ARM: dts: mvebu: Add device tree for RD-AC3X-48G4X2XL board
arm: dts: marvell: armada-375: Harmonize DWC USB3 DT nodes name
ARM: dts: turris-omnia: remove unneeded status = "okay" properties
ARM: dts: turris-omnia: update ethernet-phy node and handle name
ARM: dts: turris-omnia: add LED controller node
ARM: dts: turris-omnia: add SFP node
ARM: dts: turris-omnia: describe switch interrupt
ARM: dts: turris-omnia: add comphy handle to eth2
ARM: dts: turris-omnia: enable HW buffer management
ARM: dts: Add i2c0 pinctrl information for 98dx3236
ARM: dts: Remove non-existent i2c1 from 98dx3236
ARM: dts: armada: align GPIO hog names with dtschema
ARM: dts: dove: fix PCA95xx GPIO expander properties on A510
ARM: dts: kirkwood: replace status value "ok" by "okay"
ARM: dts: mvebu: Add CRS328-4C-20S-4S board
ARM: dts: mvebu: Add CRS305-1G-4S board
ARM: dts: mvebu: Add CRS326-24G-2S board
Link: https://lore.kernel.org/r/87h7p6j0m7.fsf@BL-laptop
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Nuvoton device tree updates for 5.11
- New machines
* Fii Kudo, a NPCM730 BMC
* Quanta GSJ, a NPCM750 BMC
* Qanta Olympus RunBMC, a NPCM750 BMC
- Updates to the common device trees and NCPM750 EVB
* tag 'nuvoton-5.11-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/bmc:
dt-bindings: vendor-prefixes: Add FII
ARM: dts: nuvoton: Add Fii Kudo system
ARM: dts: nuvoton: Add NPCM7xx RunBMC Olympus Quanta machine
ARM: dts: nuvoton: Add Quanta GSJ BMC
ARM: dts: nuvoton: Add Quanta GSJ BMC pinctrl
ARM: dts: nuvoton: Add Nuvoton NPCM730 device tree
ARM: dts: nuvoton: Add new device nodes to NPCM750 EVB
ARM: dts: nuvoton: Add new device nodes
ARM: dts: nuvoton: Add pinctrl and GPIO node
ARM: dts: nuvoton: Modify timer register size
ARM: dts: nuvoton: Modify clock parameters
Link: https://lore.kernel.org/r/CACPK8Xd8RaLv_p6t9ckBwCwtZww+2YYOAoAYQdvni0dxc2mS7A@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This pull request contains Broadcom ARM-based SoCs changes for 5.11,
please pull the following:
- Vivek updates the Linksys EA9500 DTS by adding the two additional
switch port nodes (5 & 7), providing a flash partition layout to
make the device usable with OpenWrt, and finally switches to using
the pin controller rather than using mdio-mux to get the same outcome.
- Serge fixes the USB Device Tree nodes unit name to be conformant to
the recommended name patterns.
- Rafal re-arranges all the nodes that belonged to the CRU block to be
under the CRU node (such as PLLs). He also disables the USB3 PHY node
for devices that lack USB3 and adds USB3 support to the Luxul XWR-3150
DTS.
- Jonathan drops the incorrect 'io-channel-ranges' from the Cygnus SoC
DTSI.
- Maxime disables the Wi-Fi frequencies (around 2.4GHz) for HDMI on the
Raspberry Pi 4 due to some cross-talk between the two blocks.
- Pavel updates the DWC2 USB controller RX FIFO sizes to be more
accurate for all BCM283x (Raspberr Pi) SoCs.
- Florian updates all BCM5301x and NSP Device Tree files to allow
switching the Broadcom B53 Ethernet switch device tree binding to YAML.
* tag 'arm-soc/for-5.11/devicetree' of https://github.com/Broadcom/stblinux: (22 commits)
dt-bindings: net: dsa: b53: Add YAML bindings
ARM: dts: NSP: Provide defaults ports container node
ARM: dts: NSP: Add a SRAB compatible string for each board
ARM: dts: NSP: Fix Ethernet switch SGMII register name
ARM: dts: NSP: Update ethernet switch node name
ARM: dts: BCM5301X: Provide defaults ports container node
ARM: dts: BCM5301X: Add a default compatible for switch node
ARM: dts: BCM5301X: Update Ethernet switch node name
dt-bindings: net: dsa: Document sfp and managed properties
dt-bindings: net: dsa: Extend switch nodes pattern
ARM: dts: bcm283x: increase dwc2's RX FIFO size
ARM: dts: rpi-4: disable wifi frequencies
ARM: dts: Cygnus: Drop incorrect io-channel-ranges property.
ARM: dts: BCM5301X: Enable USB 3 PHY on Luxul XWR-3150
ARM: dts: BCM5301X: Disable USB 3 PHY on devices without USB 3
ARM: dts: BCM5301X: Move CRU devices to the CRU node
ARM: dts: BCM5301X: Linksys EA9500 make use of pinctrl
ARM: dts: BCM5301X: Use corretc pinctrl compatible for 4709x
ARM: dts: BCM5301X: Linksys EA9500 add fixed partitions
ARM: dts: BCM5310X: Harmonize xHCI DT nodes name
...
Link: https://lore.kernel.org/r/20201128163410.1691529-3-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Our usual bunch of patches to support the Allwinner SoCs, this time
adding:
- Some nice pinephone additions
- I2S support for the A64, H3, H5 and H6
- New boards: Elimo Impetus, Elimo Initium, FriendlyArm ZeroPi, NanoPi R1
* tag 'sunxi-dt-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (21 commits)
ARM: dts: sun8i-h2-plus-bananapi-m2-zero: add gpio-line-names
ARM: dts: sun8i: h3: Add initial NanoPi R1 support
arm64: dts: allwinner: pinephone: Use generic sensor node names
ARM: dts: sun8i: s3: Add dts for the Elimo Initium SBC
dt-bindings: arm: sunxi: add Elimo bindings
ARM: dts: sun8i: s3: Add dtsi for the Elimo Impetus SoM
arm64: dts: allwinner: pinephone: Add Bluetooth support
arm64: dts: allwinner: pinephone: Add WiFi support
arm64: dts: allwinner: pinephone: Add light/proximity sensor
arm64: dts: allwinner: pinephone: Add LED flash
arm64: dts: allwinner: pinephone: Set ALDO3 to exactly 3v0
arm64: dts: allwinner: pinephone: Remove AC power supply
arm: dts: sunxi: h3/h5: Add I2S2 node
arm64: dts: allwinner: a64: Add I2S2 node
arm64: dts: allwinner: h6: Add I2S1 node
arm64: dts: allwinner: h6: PineH64 model B: Add wifi
ARM: dts: sun8i-v3s: Add I2C1 PB pins description
ARM: dts: sun8i: V3/S3: Add UART1 pin definitions to the V3/S3 dtsi
dt-bindings: vendors: add Elimo Engineering vendor prefix
ARM: dts: sun8i: add FriendlyArm ZeroPi support
...
Link: https://lore.kernel.org/r/551fdf4f-8a0b-4a22-ba49-b4f61520a9ab.lettre@localhost
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
AT91 DT for 5.11:
- fix USB host pinctrl
- fix DT schema warnings
* tag 'at91-dt-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: at91: sama5d3_xplained: add pincontrol for USB Host
ARM: dts: at91: sama5d4_xplained: add pincontrol for USB Host
ARM: dts: at91: sam9x60: add pincontrol for USB Host
ARM: dts: at91: at91-sama5d27_som1: fix EEPROM compatible
ARM: dts: at91: Fix schema warnings for pwm-leds
ARM: dts: at91: smartkiz: Reference led node directly
Link: https://lore.kernel.org/r/20201127220403.GA1735041@piout.net
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Commit 7ecdea4a0226 ("backlight: generic_bl: Remove this driver as it is
unused") removed geenric_bl driver from the tree, together with
corresponding config option.
Remove BACKLIGHT_GENERIC config item from all ARM configurations.
Fixes: 7ecdea4a0226 ("backlight: generic_bl: Remove this driver as it is unused")
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Link: https://lore.kernel.org/r/20201201222922.3183-2-andrey.zhizhikin@leica-geosystems.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Samsung defconfig changes for v5.11
1. Enable sound driver for Midas (Exynos4412 based) boards.
2. Enable ax88796c Ethernet driver for Artik5 (Exynos3250) board.
3. Enable Atmel touchscreen and STMPE ADC drivers for P4 Note board.
4. Build Samsung Exynos EHCI as module, to match the setting for the PHY
driver.
* tag 'samsung-defconfig-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: multi_v7_defconfig: make Samsung Exynos EHCI driver a module
ARM: exynos_defconfig: compile Atmel MXT touchscreeen as module
ARM: defconfig: add STMPE ADC driver for P4 Note
ARM: defconfig: Enable ax88796c driver for Exynos boards
ARM: multi_v7_defconfig: enable sound driver for Midas platform
ARM: exynos_defconfig: enable sound driver for Midas platform
Link: https://lore.kernel.org/r/20201201204404.22675-1-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This pull request contains ARM multi_v7_defconfig changes for 5.11,
please pull the following:
- Florian enables the ARM SCMI protocol, and the common clock, HWMON and
CPU frequency scaling drivers since those are used by ARCH_BRCMSTB
platforms
* tag 'arm-soc/for-5.11/defconfig' of https://github.com/Broadcom/stblinux:
ARM: multi_v7_defconfig: Enable ARM SCMI protocol and drivers
Link: https://lore.kernel.org/r/20201128163410.1691529-1-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
One patch to add the Realtek PHY driver to sunxi_defconfig
* tag 'sunxi-config-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: configs: sunxi: enable Realtek PHY
Link: https://lore.kernel.org/r/dffb8a7e-27ea-4025-868a-caa5868eb1ef.lettre@localhost
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
AT91 defconfig for 5.11:
- filter compiled media drivers
* tag 'at91-defconfig-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: configs: at91_dt: resync with media changes
ARM: configs: at91: sama5: resync with media changes
Link: https://lore.kernel.org/r/20201127215517.GA1733715@piout.net
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
LDO0 regulator must remain enabled always on dra71-evm boards. Disabling
this violates the data manual and will damage the device over time.
Reported-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add support for the OPP_PLUS (1.8GHz) for MPU.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
EMIF1 has ECC support, so add the DT node with address and interrupt
details to handle this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
xt875 comes up with a iva voltage of 1375000 and android runs at this too. fix
maximum voltage to be consistent with this.
Signed-off-by: Carl Philipp Klemm <philipp@uvos.xyz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The ARM version of __div64_32() encapsulates a call to __do_div64 with
non-standard argument passing. In particular, __n is a 64-bit input
argument assigned to r0-r1 and __rem is an output argument sharing half
of that r0-r1 register pair.
With __n being an input argument, the compiler is in its right to
presume that r0-r1 would still hold the value of __n past the inline
assembly statement. Normally, the compiler would have assigned non
overlapping registers to __n and __rem if the value for __n is needed
again.
However, here we enforce our own register assignment and gcc fails to
notice the conflict. In practice this doesn't cause any problem as __n
is considered dead after the asm statement and *n is overwritten.
However this is not always guaranteed and clang rightfully complains.
Let's fix it properly by making __n into an input-output variable. This
makes it clear that those registers representing __n have been modified.
Then we can extract __rem as the high part of __n with plain C code.
This asm constraint "abuse" was likely relied upon back when gcc didn't
handle 64-bit values optimally. Turns out that gcc is now able to
optimize things and produces the same code with this patch applied.
Reported-by: Antony Yu <swpenim@gmail.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
There are a couple of problems with the exception entry code that deals
with FP exceptions (which are reported as UND exceptions) when building
the kernel in Thumb2 mode:
- the conditional branch to vfp_kmode_exception in vfp_support_entry()
may be out of range for its target, depending on how the linker decides
to arrange the sections;
- when the UND exception is taken in kernel mode, the emulation handling
logic is entered via the 'call_fpe' label, which means we end up using
the wrong value/mask pairs to match and detect the NEON opcodes.
Since UND exceptions in kernel mode are unlikely to occur on a hot path
(as opposed to the user mode version which is invoked for VFP support
code and lazy restore), we can use the existing undef hook machinery for
any kernel mode instruction emulation that is needed, including calling
the existing vfp_kmode_exception() routine for unexpected cases. So drop
the call to call_fpe, and instead, install an undef hook that will get
called for NEON and VFP instructions that trigger an UND exception in
kernel mode.
While at it, make sure that the PC correction is accurate for the
execution mode where the exception was taken, by checking the PSR
Thumb bit.
Cc: Dmitry Osipenko <digetx@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Fixes: eff8728fe698 ("vmlinux.lds.h: Add PGO and AutoFDO input sections")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
This patch replaces 6 IWMMXT instructions Clang's integrated assembler
does not support in iwmmxt.S using macros, while making sure GNU
assembler still emit the same instructions. This should be easier than
providing full IWMMXT support in Clang. This is one of the last bits of
kernel code that could be compiled but not assembled with clang. Once
all of it works with IAS, we no longer need to special-case 32-bit Arm
in Kbuild, or turn off CONFIG_IWMMXT when build-testing.
"Intel Wireless MMX Technology - Developer Guide - August, 2002" should
be referenced for the encoding schemes of these extensions.
Link: https://github.com/ClangBuiltLinux/linux/issues/975
Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Suggested-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Jian Cai <jiancai@google.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
KASAN uses the routines in stacktrace.c to capture the call stack each
time memory gets allocated or freed. Some of these routines are also
used to log CPU and memory context when exceptions are taken, and so
in some cases, memory accesses may be made that are not strictly in
line with the KASAN constraints, and may therefore trigger false KASAN
positives.
So follow the example set by other architectures, and simply disable
KASAN instrumentation for these routines.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
Since
commit 0bddd227f3dc ("Documentation: update for gcc 4.9 requirement")
the minimum supported version of GCC is gcc-4.9. It's now safe to remove
this code.
Link: https://github.com/ClangBuiltLinux/linux/issues/427
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
LLD does not yet support any big endian architectures. Make this config
non-selectable when using LLD until LLD is fixed.
Link: https://github.com/ClangBuiltLinux/linux/issues/965
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
|
|
According to the datasheet (Rev. 1.9) the RTL8211F requires at least
72ms "for internal circuits settling time" before accessing the PHY
registers. On similar boards with the same PHY this fixes an issue where
Ethernet link would not come up when using ip link set down/up.
Fixes: a2c6e82e5341 ("ARM: dts: meson: switch to the generic Ethernet PHY reset bindings")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> # on Odroid-C1+
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/ff78772b306411e145769c46d4090554344db41e.1607363522.git.stefan@agner.ch
|
|
These definitions are evidently left over from the days when
sparsemem settings were platform specific. This was no longer
the case when the platform got merged.
There was no warning in the past, but now the asm/sparsemem.h
header ends up being included indirectly, causing this warning:
In file included from /git/arm-soc/arch/arm/mach-keystone/keystone.c:24:
arch/arm/mach-keystone/memory.h:10:9: warning: 'SECTION_SIZE_BITS' macro redefined [-Wmacro-redefined]
#define SECTION_SIZE_BITS 34
^
arch/arm/include/asm/sparsemem.h:23:9: note: previous definition is here
#define SECTION_SIZE_BITS 28
^
Clearly the definitions never had any effect here, so remove them.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20201203231847.1484900-1-arnd@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
i.MX fixes for 5.10, round 5:
- Fix a regression on SoC revision detection with ANATOP, that is
introduced by commit 4a4fb66119eb ("ARM: imx: Add missing
of_node_put()").
- Drop PAD_GPIO_6 from imx6qdl-wandboard ENET pin group, as the pin is
used by camera sensor now.
- Fix I2C3_SCL pinmux on imx6qdl-kontron-samx6i board, so that SoM EEPROM
can be accessed.
* tag 'imx-fixes-5.10-5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6qdl-kontron-samx6i: fix I2C_PM scl pin
ARM: dts: imx6qdl-wandboard-revd1: Remove PAD_GPIO_6 from enetgrp
ARM: imx: Use correct SRC base address
Link: https://lore.kernel.org/r/20201201091820.GW4072@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
A few more RGMII-ID fixes, and a bunch of other more random fixes
* tag 'sunxi-fixes-for-5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun7i: pcduino3-nano: enable RGMII RX/TX delay on PHY
ARM: dts: sun8i: v3s: fix GIC node memory range
ARM: dts: sun8i: v40: bananapi-m2-berry: Fix ethernet node
ARM: dts: sun8i: r40: bananapi-m2-berry: Fix dcdc1 regulator
ARM: dts: sun7i: bananapi: Enable RGMII RX/TX delay on Ethernet PHY
ARM: dts: s3: pinecube: align compatible property to other S3 boards
ARM: sunxi: Add machine match for the Allwinner V3 SoC
arm64: dts: allwinner: h6: orangepi-one-plus: Fix ethernet
Link: https://lore.kernel.org/r/1280f1de-1b6d-4cc2-8448-e5a9096a41e8.lettre@localhost
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
GTA04 uses that for controlling the td028ttec1 panel. So
for easier testing/bisecting it is useful to have it
enabled in the defconfig.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
On the GTA04A5 od->_driver_status was not set to BUS_NOTIFY_BIND_DRIVER
during probe of the second mmc used for wifi. Therefore
omap_device_late_idle idled the device during probing causing oopses when
accessing the registers.
It was not set because od->_state was set to OMAP_DEVICE_STATE_IDLE
in the notifier callback. Therefore set od->_driver_status also in that
case.
This came apparent after commit 21b2cec61c04 ("mmc: Set
PROBE_PREFER_ASYNCHRONOUS for drivers that existed in v4.4") causing this
oops:
omap_hsmmc 480b4000.mmc: omap_device_late_idle: enabled but no driver. Idling
8<--- cut here ---
Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa0b402c
...
(omap_hsmmc_set_bus_width) from [<c07996bc>] (omap_hsmmc_set_ios+0x11c/0x258)
(omap_hsmmc_set_ios) from [<c077b2b0>] (mmc_power_up.part.8+0x3c/0xd0)
(mmc_power_up.part.8) from [<c077c14c>] (mmc_start_host+0x88/0x9c)
(mmc_start_host) from [<c077d284>] (mmc_add_host+0x58/0x84)
(mmc_add_host) from [<c0799190>] (omap_hsmmc_probe+0x5fc/0x8c0)
(omap_hsmmc_probe) from [<c0666728>] (platform_drv_probe+0x48/0x98)
(platform_drv_probe) from [<c066457c>] (really_probe+0x1dc/0x3b4)
Fixes: 04abaf07f6d5 ("ARM: OMAP2+: omap_device: Sync omap_device and pm_runtime after probe defer")
Fixes: 21b2cec61c04 ("mmc: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in v4.4")
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
[tony@atomide.com: left out extra parens, trimmed description stack trace]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add Aspeed AST2600 EDAC node into the common devicetree.
Signed-off-by: Troy Lee <troy_lee@aspeedtech.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lkml.kernel.org/r/20201207090013.14145-2-troy_lee@aspeedtech.com
|
|
We want the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull USB fixes from Greg KH:
"Here are some small USB fixes for 5.10-rc7 that resolve a number of
reported issues, and add some new device ids.
Nothing major here, but these solve some problems that people were
having with the 5.10-rc tree:
- reverts for USB storage dma settings that broke working devices
- thunderbolt use-after-free fix
- cdns3 driver fixes
- gadget driver userspace copy fix
- new device ids
All of these except for the reverts have been in linux-next with no
reported issues. The reverts are "clean" and were tested by Hans, as
well as passing the 0-day tests"
* tag 'usb-5.10-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: gadget: f_fs: Use local copy of descriptors for userspace copy
usb: ohci-omap: Fix descriptor conversion
Revert "usb-storage: fix sdev->host->dma_dev"
Revert "uas: fix sdev->host->dma_dev"
Revert "uas: bump hw_max_sectors to 2048 blocks for SS or faster drives"
USB: serial: kl5kusb105: fix memleak on open
USB: serial: ch341: sort device-id entries
USB: serial: ch341: add new Product ID for CH341A
USB: serial: option: fix Quectel BG96 matching
usb: cdns3: core: fix goto label for error path
usb: cdns3: gadget: clear trb->length as zero after preparing every trb
usb: cdns3: Fix hardware based role switch
USB: serial: option: add support for Thales Cinterion EXS82
USB: serial: option: add Fibocom NL668 variants
thunderbolt: Fix use-after-free in remove_unplugged_switch()
|
|
Pull Kbuild fixes from Masahiro Yamada:
- Move -Wcast-align to W=3, which tends to be false-positive and there
is no tree-wide solution.
- Pass -fmacro-prefix-map to KBUILD_CPPFLAGS because it is a
preprocessor option and makes sense for .S files as well.
- Disable -gdwarf-2 for Clang's integrated assembler to avoid warnings.
- Disable --orphan-handling=warn for LLD 10.0.1 to avoid warnings.
- Fix undesirable line breaks in *.mod files.
* tag 'kbuild-fixes-v5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: avoid split lines in .mod files
kbuild: Disable CONFIG_LD_ORPHAN_WARN for ld.lld 10.0.1
kbuild: Hoist '--orphan-handling' into Kconfig
Kbuild: do not emit debug info for assembly with LLVM_IAS=1
kbuild: use -fmacro-prefix-map for .S sources
Makefile.extrawarn: move -Wcast-align to W=3
|
|
While I was doing zram testing, I found sometimes decompression failed
since the compression buffer was corrupted. With investigation, I found
below commit calls cond_resched unconditionally so it could make a
problem in atomic context if the task is reschedule.
BUG: sleeping function called from invalid context at mm/vmalloc.c:108
in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 946, name: memhog
3 locks held by memhog/946:
#0: ffff9d01d4b193e8 (&mm->mmap_lock#2){++++}-{4:4}, at: __mm_populate+0x103/0x160
#1: ffffffffa3d53de0 (fs_reclaim){+.+.}-{0:0}, at: __alloc_pages_slowpath.constprop.0+0xa98/0x1160
#2: ffff9d01d56b8110 (&zspage->lock){.+.+}-{3:3}, at: zs_map_object+0x8e/0x1f0
CPU: 0 PID: 946 Comm: memhog Not tainted 5.9.3-00011-gc5bfc0287345-dirty #316
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1 04/01/2014
Call Trace:
unmap_kernel_range_noflush+0x2eb/0x350
unmap_kernel_range+0x14/0x30
zs_unmap_object+0xd5/0xe0
zram_bvec_rw.isra.0+0x38c/0x8e0
zram_rw_page+0x90/0x101
bdev_write_page+0x92/0xe0
__swap_writepage+0x94/0x4a0
pageout+0xe3/0x3a0
shrink_page_list+0xb94/0xd60
shrink_inactive_list+0x158/0x460
We can fix this by removing the ZSMALLOC_PGTABLE_MAPPING feature (which
contains the offending calling code) from zsmalloc.
Even though this option showed some amount improvement(e.g., 30%) in
some arm32 platforms, it has been headache to maintain since it have
abused APIs[1](e.g., unmap_kernel_range in atomic context).
Since we are approaching to deprecate 32bit machines and already made
the config option available for only builtin build since v5.8, lastly it
has been not default option in zsmalloc, it's time to drop the option
for better maintenance.
[1] http://lore.kernel.org/linux-mm/20201105170249.387069-1-minchan@kernel.org
Fixes: e47110e90584 ("mm/vunmap: add cond_resched() in vunmap_pmd_range")
Signed-off-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Harish Sriram <harish@linux.ibm.com>
Cc: Uladzislau Rezki <urezki@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20201117202916.GA3856507@google.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The reference to cache_is_vivt() was moved into a header file,
which now causes a build failure in rare randconfig builds:
arch/arm/include/asm/highmem.h:52:43: error: implicit declaration of function 'cache_is_vivt' [-Werror,-Wimplicit-function-declaration]
Add an explicit include to make it build reliably.
Fixes: 2a15ba82fa6c ("ARM: highmem: Switch to generic kmap atomic")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Link: https://lore.kernel.org/r/20201204165930.3877571-1-arnd@kernel.org
|
|
There were a bunch of issues with the patch converting the
OMAP1 OSK board to use descriptors for controlling the USB
host:
- The chip label was incorrect
- The GPIO offset was off-by-one
- The code should use sleeping accessors
This patch tries to fix all issues at the same time.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Fixes: 15d157e87443 ("usb: ohci-omap: Convert to use GPIO descriptors")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201130083033.29435-1-linus.walleij@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ARM Cortex-A57 and Cortex-A72 cores running in 32-bit mode are affected
by silicon errata #1742098 and #1655431, respectively, where the second
instruction of a AES instruction pair may execute twice if an interrupt
is taken right after the first instruction consumes an input register of
which a single 32-bit lane has been updated the last time it was modified.
This is not such a rare occurrence as it may seem: in counter mode, only
the least significant 32-bit word is incremented in the absence of a
carry, which makes our counter mode implementation susceptible to these
errata.
So let's shuffle the counter assignments around a bit so that the most
recent updates when the AES instruction pair executes are 128-bit wide.
[0] ARM-EPM-049219 v23 Cortex-A57 MPCore Software Developers Errata Notice
[1] ARM-EPM-012079 v11.0 Cortex-A72 MPCore Software Developers Errata Notice
Cc: <stable@vger.kernel.org> # v5.4+
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Conflicts:
drivers/net/ethernet/ibm/ibmvnic.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
CAN0 and CAN1 instances share the same message ram configured
at 0x210000 on sama5d2 Linux systems.
According to current configuration of CAN0, we need 0x1c00 bytes
so that the CAN1 don't overlap its message ram:
64 x RX FIFO0 elements => 64 x 72 bytes
32 x TXE (TX Event FIFO) elements => 32 x 8 bytes
32 x TXB (TX Buffer) elements => 32 x 72 bytes
So a total of 7168 bytes (0x1C00).
Fix offset to match this needed size.
Make the CAN0 message ram ioremap match exactly this size so that is
easily understandable. Adapt CAN1 size accordingly.
Fixes: bc6d5d7666b7 ("ARM: dts: at91: sama5d2: add m_can nodes")
Reported-by: Dan Sneddon <dan.sneddon@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Cristian Birsan <cristian.birsan@microchip.com>
Cc: stable@vger.kernel.org # v4.13+
Link: https://lore.kernel.org/r/20201203091949.9015-1-nicolas.ferre@microchip.com
|
|
Due to strobe signal not being propagated from CPU to securam
the securam needs to be mapped as device or strongly ordered memory
to work properly. Otherwise, updating to one offset may affect
the adjacent locations in securam.
Fixes: d4ce5f44d4409 ("ARM: dts: at91: sama5d2: Add securam node")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/1606903025-14197-3-git-send-email-claudiu.beznea@microchip.com
|
|
atmel,osc-bypass property sets the bit 1 at main oscillator register.
On SAM9X60 this bit is not valid according to datasheet (chapter
28.16.9 PMC Clock Generator Main Oscillator Register).
Fixes: 1e5f532c2737 ("ARM: dts: at91: sam9x60: add device tree for soc and board")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Marco Cardellini <marco.cardellini@microchip.com>
Link: https://lore.kernel.org/r/1606903025-14197-2-git-send-email-claudiu.beznea@microchip.com
|
|
Commit 2024b130b0c8 ("ARM: dts: exynos: Add Ethernet to Artik 5 board")
added ethernet chip on SPI0 bus and the whole bunch of assigned clock
entries to ensure proper clock rates and topology. Limit the assigned
clock parents only to the direct clocks of the SPI0 device and assume
that MPLL clock is already properly configured.
The applied clock topology was incorrect as some clocks between were
missing, what resulted in the following warning:
clk: failed to reparent div_mpll_pre to mout_mpll: -22
Fixes: 2024b130b0c8 ("ARM: dts: exynos: Add Ethernet to Artik 5 board")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20201202122029.22198-1-m.szyprowski@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
The SMDK6410 DTS was incorrectly called mini6410, probably copy-paste
from FriendlyARM Mini6410 board.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201117201106.128813-4-krzk@kernel.org
|
Ard Biesheuvel
Arnd Bergmann
Andrey Zhizhikin
Tero Kristo
Carl Philipp Klemm
Nicolas Pitre
Jian Cai
Nick Desaulniers
Stefan Agner
Andreas Kemnade
Troy Lee
Greg Kroah-Hartman
Linus Torvalds
Minchan Kim
Linus Walleij
Jakub Kicinski
Nicolas Ferre
Claudiu Beznea
Marek Szyprowski
Krzysztof Kozlowski