| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add a compatible for SMDK2416 board next to the SoC compatible.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201117201106.128813-3-krzk@kernel.org
|
|
atmel,adc-res, atmel,adc-res-names and the trigger nodes are not parsed by
the driver anymore and the information is now defined in the driver data.
Also remove the leftover #address-cells and #size-cells that were used when
the trigger nodes had a unit-address.
Finally, the default is already to use the highest resoution. Remove
atmel,adc-use-res from the SoC dtsi.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20201128222818.1910764-11-alexandre.belloni@bootlin.com
|
|
The triggers for the ADC were taken from at91sam9260 dtsi but are not
correct.
Fixes: a4c1d6c75822 ("ARM: at91/dt: sam9rl: add lcd, adc, usb gadget and pwm support")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201128222818.1910764-10-alexandre.belloni@bootlin.com
|
|
The ADC is different from the at91sam9x5 ADC. Not only it doesn't have the
same resolution but it even has only one and the LOWRES bit doesn't exist.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20201128222818.1910764-9-alexandre.belloni@bootlin.com
|
|
Switch to the new pwm-atmel-tcb binding that avoid wasting TCB channels.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Antoine Aubert <a.aubert@overkiz.com>
Link: https://lore.kernel.org/r/20201030183658.1007395-5-alexandre.belloni@bootlin.com
|
|
Currently, '--orphan-handling=warn' is spread out across four different
architectures in their respective Makefiles, which makes it a little
unruly to deal with in case it needs to be disabled for a specific
linker version (in this case, ld.lld 10.0.1).
To make it easier to control this, hoist this warning into Kconfig and
the main Makefile so that disabling it is simpler, as the warning will
only be enabled in a couple places (main Makefile and a couple of
compressed boot folders that blow away LDFLAGS_vmlinx) and making it
conditional is easier due to Kconfig syntax. One small additional
benefit of this is saving a call to ld-option on incremental builds
because we will have already evaluated it for CONFIG_LD_ORPHAN_WARN.
To keep the list of supported architectures the same, introduce
CONFIG_ARCH_WANT_LD_ORPHAN_WARN, which an architecture can select to
gain this automatically after all of the sections are specified and size
asserted. A special thanks to Kees Cook for the help text on this
config.
Link: https://github.com/ClangBuiltLinux/linux/issues/1187
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
Things are wired up for powersaving, so lets use the corresponding
compatible and also update a deprecated property name.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
AES needs to be disabled on Nokia N950/N9 as well (HS devices), otherwise
kernel fails to boot.
Fixes: c312f066314e ("ARM: dts: omap3: Migrate AES from hwmods to sysc-omap2")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 785b5bb41b0a ("PM: AVS: Drop the avs directory and the
corresponding Kconfig") moved AVS code to SOC-specific folders, and
removed corresponding Kconfig from drivers/power, leaving original
POWER_AVS config option enabled in omap2plus_defconfig file.
Remove the option, which has no references in the tree anymore.
Fixes: 785b5bb41b0a ("PM: AVS: Drop the avs directory and the corresponding Kconfig")
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The dual_mac mode has been preserved the same way between legacy and new
driver, and one port devices works the same as 1 dual_mac port - it's safe
to switch drivers.
So, Switch amam335x-evm, am335x-evmsk and am335x-icev2 boards to use new
cpsw switch driver. Those boards have or 2 Ext. port wired and configured
in dual_mac mode by default, or only 1 Ext. port.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add DT node for the new cpsw switchdev based driver.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The 'eth_switch' name has been misspelled in the imx28.dtsi file,
so this change fixes it.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Protonic WD3 is a proof of concept platform for tractor e-cockpit applications
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Use the correct pin for the i2c scl signal else we can't access the
SoM eeprom.
Fixes: 2a51f9dae13d ("ARM: dts: imx6qdl-kontron-samx6i: Add iMX6-based Kontron SMARC-sAMX6i module")
Signed-off-by: Bernd Bauer <bernd.bauer@anton-paar.com>
[m.felsch@pengutronix.de: Adapt commit message]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Set it to max. allowed 375kHz for faster transfers. The limit is given
by the erratum [1].
[1] https://www.nxp.com/docs/en/errata/IMX6DQCE.pdf
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Since commit 8ad2d1dcce54 ("ARM: dts: imx6qdl-wandboard: Add OV5645 camera
support") the PAD_GPIO_6 is used for providing the camera sensor clock.
Remove it from the enetgrp to fix the following IOMXU conflict:
[ 9.972414] imx6q-pinctrl 20e0000.pinctrl: pin MX6Q_PAD_GPIO_6 already requested by 2188000.ethernet; cannot claim for 1-003c
[ 9.983857] imx6q-pinctrl 20e0000.pinctrl: pin-140 (1-003c) status -22
[ 9.990514] imx6q-pinctrl 20e0000.pinctrl: could not request pin 140 (MX6Q_PAD_GPIO_6) from group ov5645grp on device 20e0000.pinctrl
Fixes: 8ad2d1dcce54 ("ARM: dts: imx6qdl-wandboard: Add OV5645 camera support")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Commit 4a4fb66119eb ("ARM: imx: Add missing of_node_put()") accidentally
forgot to rename a variable, which caused the wrong address to be used
and, in our case, the ULL getting falsely identified as ULZ.
Fixes: 4a4fb66119eb ("ARM: imx: Add missing of_node_put()")
Signed-off-by: Robert Karszniewicz <r.karszniewicz@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
ASPEED soc driver updates for 5.11
New drivers:
- SoC info driver to expose revision information
New features:
- AST2600 support for the LPC control driver. This includes
setting the LPC2AHB bridge up in a backwards compatible manner.
Cleanups:
- LPC control
- Kconfig
- Bindings updates for AST2600 strings
* tag 'aspeed-5.11-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
soc: aspeed: Enable drivers with ARCH_ASPEED
soc: aspeed: Fix a reference leak in aspeed_socinfo_init()
soc: aspeed: remove unneeded semicolon
soc: aspeed-lpc-ctrl: Fix driver name
soc: aspeed-lpc-ctrl: Fix whitespace
soc: aspeed-lpc-ctrl: LPC to AHB mapping on ast2600
soc: aspeed-lpc-ctrl: Fail probe of lpc-ctrl if reserved memory is not aligned
soc: aspeed: lpc: Add AST2600 compatible strings
dt-bindings: aspeed-lpc: Add AST2600 compatible strings
ARM: dts: aspeed: Add silicon id node
soc: aspeed: Add soc info driver
dt-bindings: aspeed: Add silicon id node to SCU
soc: aspeed: Improve kconfig
Link: https://lore.kernel.org/r/CACPK8Xe=9ezhyWRMqVOEQr7SU1YoYfVBGGdGzjmE4SiBr--vJQ@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add device tree for RD-AC3X-48G4X2XL board. This has a Armada 382 SoC on
a interposer board connected to a baseboard with a Prestera AC3X ASIC
connected via PCI.
Signed-off-by: Aryan Srivastava <aryan.srivastava@alliedtelesis.co.nz>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
In accordance with the DWC USB3 bindings the corresponding node
name is suppose to comply with the Generic USB HCD DT schema, which
requires the USB nodes to have the name acceptable by the regexp:
"^usb(@.*)?" . Make sure the "snps,dwc3"-compatible nodes are correctly
named.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Rockchip RK3288 and RK3399Pro based VMARC SOM has sdio0 for
connecting WiFi/BT devices as a pluggable card via M.2 E-Key.
Add associated sdio0 nodes, properties.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20201023181814.220974-2-jagan@amarulasolutions.com
[moved the unrelated rtc addition to a separate patch]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add the hym8563 rtc found on the rk3288 variant of the VMARC SOM.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20201023181814.220974-2-jagan@amarulasolutions.com
[split out of the original patch, as it was a change unrelated
to the commit description]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
A test with the command below gives for example this error:
/arch/arm/boot/dts/rv1108-evb.dt.yaml:
wdt@10360000: $nodename:0: 'wdt@10360000'
does not match '^watchdog(@.*|-[0-9a-f])?$'
Fix it by renaming the wdt nodename to watchdog
in the rv1108.dtsi file.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/watchdog/snps,dw-wdt.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20201116150756.14265-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Only nodes which have status = "disabled" defined from included files
need status = "okay".
The ethernet-phy node and the i2cmux node do not need it, since they are
wholly defined here.
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Andreas Färber <afaerber@suse.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Use property name `phy-handle` instead of the deprecated `phy` to
connect eth2 to the PHY.
Rename the node from "phy@1" to "ethernet-phy@1", since "phy@1" is
incorrect according to device-tree bindings documentation.
Also remove the "ethernet-phy-id0141.0DD1" compatible string, it is not
needed. Kernel can read the PHY identifier itself.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Andreas Färber <afaerber@suse.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Linux now has incomplete support for the LED controller on Turris Omnia:
it can set brightness and colors for each LED.
The controller can also put these LEDs into HW controlled mode, in which
the LEDs are controlled by HW: for example the WAN LED is connected via
MCU to the WAN PHY LED pin.
The driver does not support these HW controlled modes yet, and on probe
puts the LEDs into SW controlled mode.
Add node describing the LED controller, but disable it for now.
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Andreas Färber <afaerber@suse.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Turris Omnia has an SFP cage that, together with WAN PHY, is connected
to eth2 SerDes via a SerDes multiplexor. When a SFP module is present,
the multiplexor switches the SerDes signal from PHY to SFP.
Describe the SFP cage, but leave it disabled. Until phylink has support
for such configuration, we are leaving it to U-Boot to enable SFP and
disable WAN PHY at boot time depending on whether a SFP module is
present.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: 26ca8b52d6e1 ("ARM: dts: add support for Turris Omnia")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King - ARM Linux admin <linux@armlinux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Andreas Färber <afaerber@suse.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Describe switch interrupt for Turris Omnia so that the CPU does not have
to poll the switch. We also need to to set mpp45 pin to gpio function
for this.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: 26ca8b52d6e1 ("ARM: dts: add support for Turris Omnia")
Cc: linux-arm-kernel@lists.infradead.org
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Andreas Färber <afaerber@suse.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The eth2 controller on Turris Omnia is connected to SerDes. For SFP to
be able to switch between 1G and 2.5G modes the comphy link has to be
defined.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: f3a6a9f3704a ("ARM: dts: add description for Armada 38x ...")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The buffer manager is available on Turris Omnia but needs to be
described in device-tree to be used.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: 26ca8b52d6e1 ("ARM: dts: add support for Turris Omnia")
Cc: linux-arm-kernel@lists.infradead.org
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Andreas Färber <afaerber@suse.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
This adds support for the OMNIA Flex Concentrator product
from Kamstrup A/S. It's providing radio mesh communication
infrastructure for smart electricity meters.
Kamstrup OMNIA is a modular and scalable smart grid platform.
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Update the calibration table to make the temperature more accurate.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
i.MX23 and i.MX28 SoCs unique identifiers are factory-programmed
in On-Chip OTP memory. i.MX28's 64-bit unique id is in
HW_OCOTP_OPS2:HW_OCOTP_OPS3 (see MCIMX28 Ref. Man., sec. 20.4.22-23).
i.MX23 provides 32-bit long unique id in HW_OCOTP_OPS3.
Though not clearly documented, there is a clue in sec. 35.9.3.
The unique id is reported in /sys/devices/soc0/serial_number
and in /proc/cpuinfo
Signed-off-by: Ivan Zaentsev <ivan.zaentsev@wirenboard.ru>
Suggested-by: Evgeny Boger <boger@wirenboard.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The range of dcfg reg is wrong, which overlap with other device,
such as rcpm. This issue causing rcpm driver failed to claim
reg resource when calling devm_ioremap_resource().
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The data of property 'fsl,rcpm-wakeup' is not corrcet, which causing
RCPM driver incorrectly program register IPPDEXPCR1, then flextimer is
wrongly clock gated during system suspend, can't send interrupt to
wake.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This converts the Collie battery driver to use GPIO descriptors.
We use a mixture of 3 GPIOs defined in the machine and 3
GPIOs requested directly from the ucb1x00 chip.
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
This converts the S3C ADC battery to use GPIO descriptors
instead of a global GPIO number for the charging completed
GPIO. Using the pattern from the GPIO charger we name this
GPIO line "charge-status" in the board file.
Cc: linux-samsung-soc@vger.kernel.org
Cc: Sergiy Kibrik <sakib@darkstar.site>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Pull locking fixes from Thomas Gleixner:
"Two more places which invoke tracing from RCU disabled regions in the
idle path.
Similar to the entry path the low level idle functions have to be
non-instrumentable"
* tag 'locking-urgent-2020-11-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
intel_idle: Fix intel_idle() vs tracing
sched/idle: Fix arch_cpu_idle() vs tracing
|
|
Add pinctrl information for the 98dx3236 (and variants). There is only
one choice for i2c0 MPP14 and MPP15.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The switches with integrated CPUs have only got a single i2c controller.
They incorrectly gained one when they were split from the Armada-XP.
Fixes: 43e28ba87708 ("ARM: dts: Use armada-370-xp as a base for armada-xp-98dx3236")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The convention for node names is to use hyphens, not underscores.
dtschema for pca95xx expects GPIO hogs to end with 'hog' prefix.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The PCA95xx GPIO expander requires GPIO controller properties to operate
properly.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
While the DT parser recognizes "ok" as a valid value for the
"status" property, it is actually mentioned nowhere. Use the
proper value "okay" instead, as done in the majority of files
already.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
MikroTik CRS328-4C-20S-4S board has a switch chip with an integrated
Marvell Prestera 98DX3236 CPU.
This commit includes two board variants, namely the factory
default one and a Bit variant. The Bit variant has a
bigger Macronix flash.
This device tree includes basic Linux support.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
MikroTik CRS305-1G-4S board has a switch chip with an integrated
Marvell Prestera 98DX3236 CPU.
This commit includes two board variants, namely the factory
default one and a Bit variant. The Bit variant has a
bigger Macronix flash.
This device tree includes basic Linux support.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
MikroTik CRS326-24G-2S board has a switch chip with an integrated
Marvell Prestera 98DX3236 CPU.
This commit includes two board variants, namely the factory
default one and a Bit variant. The Bit variant has a
bigger Macronix flash.
This device tree includes basic Linux support.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
This property is used by io-channel consumers, not providers so should
not present here. Note dt_schema will now detect this error as there
is a dependency between this property and io-channels.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201115192951.1073632-7-jic23@kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
Enable the ARM SCMI protocol and the common clock, cpufreq and sensors
drivers. Broadcom STB platforms (ARCH_BRCMSTB) implement SCMI to provide
support for CPU frequency scaling, clock configuration and temperature
and current sensors.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Trivial conflict in CAN, keep the net-next + the byteswap wrapper.
Conflicts:
drivers/net/can/usb/gs_usb.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
Krzysztof Kozlowski
Alexandre Belloni
Nathan Chancellor
Andreas Kemnade
Aaro Koskinen
Andrey Zhizhikin
Grygorii Strashko
Lukasz Majewski
Oleksij Rempel
Bernd Bauer
Marco Felsch
Fabio Estevam
Robert Karszniewicz
Arnd Bergmann
Aryan Srivastava
Serge Semin
Jagan Teki
Johan Jonker
Marek Behún
Bruno Thomsen
Yuantian Tang
Ivan Zaentsev
Greg Kroah-Hartman
Ran Wang
Linus Walleij
Linus Torvalds
Chris Packham
Adrian Schmutzler
Luka Kovacic
Jonathan Cameron
Florian Fainelli
Jakub Kicinski