| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This adds the missing properties to the PWR LED for the RPi 3 & 4 boards,
which are already set for the other boards. Without them we will lose
the LED state after suspend.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Fix AMDTEE memory leak in amdtee_open_session()
* tag 'tee-amdtee-fix-for-5.6' of https://git.linaro.org/people/jens.wiklander/linux-tee: (344 commits)
tee: amdtee: fix memory leak in amdtee_open_session()
Linux 5.6-rc2
ext4: improve explanation of a mount failure caused by a misconfigured kernel
Input: cyapa - replace zero-length array with flexible-array member
Input: tca6416-keypad - replace zero-length array with flexible-array member
Input: gpio_keys_polled - replace zero-length array with flexible-array member
IB/mlx5: Use div64_u64 for num_var_hw_entries calculation
nvme: fix the parameter order for nvme_get_log in nvme_get_fw_slot_info
nvme/pci: move cqe check after device shutdown
nvme: prevent warning triggered by nvme_stop_keep_alive
nvme/tcp: fix bug on double requeue when send fails
cifs: make sure we do not overflow the max EA buffer size
cifs: enable change notification for SMB2.1 dialect
netdevice.h: fix all kernel-doc and Sphinx warnings
net: dsa: tag_ar9331: Make sure there is headroom for tag
net: dsa: tag_qca: Make sure there is headroom for tag
net, ip6_tunnel: enhance tunnel locate with link check
net/smc: no peer ID in CLC decline for SMCD
net/smc: transfer fasync_list in case of fallback
net: hns3: fix a copying IPv6 address error in hclge_fd_get_flow_tuples()
...
Link: https://lore.kernel.org/r/20200227165205.GA7926@jade
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Renesas Fixes for v5.6
- Restore R-Car M3-W support,
- Drop deprecated compatible value to ease DT binding conversion to
json-schema.
* tag 'renesas-fixes-for-v5.6-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
ARM: dts: r8a7779: Remove deprecated "renesas, rcar-sata" compatible value
arm64: defconfig: Replace ARCH_R8A7796 by ARCH_R8A77960
Link: https://lore.kernel.org/r/20200226105236.18368-1-geert+renesas@glider.be
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The OMAP4 IPU hwmod is currently not used in DT, and the new DTS
node shall be added as per the new OMAP remoteproc bindings with
the underneath MMU device relying on the ti-sysc infrastructure.
Drop the legacy hwmod data for OMAP4 IPU as this will not be used
going forward.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The OMAP4 DSP hwmod is used in DT, but the DT node is not
probing any real driver. The DSP device-tree node shall be
updated as per the new OMAP remoteproc bindings with the
underneath MMU device relying on the ti-sysc infrastructure.
Drop the legacy hwmod data for the DSP device along with the
custom ti,hwmods property. They have to be dropped together
since the early platform data init code is based on the custom
ti,hwmods property.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The PRUSS hwmod is currently not used in DT, and the new DTS
nodes shall be added using the ti-sysc infrastructure and the
omap-prm reset driver. Drop the legacy hwmod data for the
PRUSS module on both the AM33xx and AM437x family of SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add idle_states table for CPU on am437x. Currently just add C1 state
which gates the MPU clock domain.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add idle_states table for CPU on am335x. Currently just add C1 state
which gates the MPU clock domain.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add CONFIG_ARM_CPUIDLE and supporting CONFIG_DT_IDLE_STATES as am335x
and am437x will make use of these drivers.
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
In order for am335x and am437x to properly enter deeper c-states in
cpuidle they must always call into the sleep33/43xx suspend code and
also sometimes invoke the wkup_m3_ipc driver. These are both controlled
by the pm33xx module so we must provide a method for the platform code
to call back into the module when it is available as the core cpuidle
ops that are invoked by the cpuidle-arm driver must remain as built in.
Extend the init platform op to take an idle function as an argument so
that we can use this to call into the pm33xx module for c-states that
need it. Also add a deinit op so we can unregister this idle function
from the PM core when the pm33xx module gets unloaded.
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
am335x and am437x can now make use of the generic cpuidle-arm driver.
This requires that we define init and suspend ops to be passed set as
the cpuidle ops for the SoC. These ops are invoked directly at the last
stage of the cpuidle-arm driver in order to allow low level platform
code to run and bring the CPU the rest of the way into it's desired idle
state. It is required that the CPUIDLE_METHOD_OF_DECLARE be called from
code that is built in so define these ops in pm33xx-core where the
always built-in portion of the PM code for these SoCs lives.
Additionally, although an soc_suspend function is already exposed by the
pm33xx platform code, it contains additional operations needed for full
SoC suspend beyond what is needed for a relatively simple CPU suspend
needed during cpuidle. To get around this introduce cpu_suspend ops to
be used by the am335x and am437x PM driver for the last stage of cpuidle
path.
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
|
|
There is a second PWM unit available in the PL I/O block.
Add a node and pinmux definition for it.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
Update the v7 cache_clean_flush routine to take into account the
memory range passed in r0/r1, and perform cache maintenance by
virtual address on this range instead of set/way maintenance, which
is inappropriate for the purpose of maintaining the cached state of
memory contents.
Since this removes any use of the stack in the implementation of
cache_clean_flush(), we can also drop some code that manages the
value of the stack pointer before calling it.
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
In preparation for turning the decompressor's cache clean/flush
operations into proper by-VA maintenance for v7 cores, pass the
start and end addresses of the regions that need cache maintenance
into cache_clean_flush in registers r0 and r1.
Currently, all implementations of cache_clean_flush ignore these
values, so no functional change is expected as a result of this
patch.
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
Before adding another reference to the inflated image size, factor
out the slightly complicated way of loading the unaligned little-endian
constant from the end of the compressed data.
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
The last 8MB of physical memory on Artik520 family boards is reserved for
secure firmware. Adjust the total amount of the memory defined in
exynos3250-artik5.dtsi to match the memory available for the Linux kernel.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Recent omap changes added runtime checks to use omap_smccc_smc()
when optee is configured in dts. As the omap-secure code can be
built for ARMv6 only without ARMv7 and use custom smc calls, we
now get a build error:
omap-secure.c:(.text+0x94): undefined reference to `__arm_smccc_smc'
As there secure calls are not used for ARMv6, we should not build
secure-common, and not call omap_secure_init() for omap2.
Fixes: c37baa06f8a9 ("ARM: OMAP2+: Fix undefined reference to omap_secure_init")
Reported-by: kbuild test robot <lkp@intel.com>
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Steven Price <steven.price@arm.com>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
dra76x is not affected by i887 which requires mmc3 node to be limited to
a max frequency of 64 MHz. Fix this by overwriting the correct value in
the the dra76 specific dtsi.
Fixes: 895bd4b3e5ec ("ARM: dts: Add support for dra76-evm")
Cc: stable@vger.kernel.org
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
'dma-ranges' in a PCI bridge node does correctly set dma masks for PCI
devices not described in the DT. Certain DRA7 platforms (e.g., DRA76)
has RAM above 32-bit boundary (accessible with LPAE config) though the
PCIe bridge will be able to access only 32-bits. Add 'dma-ranges'
property in PCIe RC DT nodes to indicate the host bridge can access
only 32 bits.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We need to know SoC type and features for cases where the same SoC
may be installed in various versions on the same board and would need
a separate dts file otherwise for the different variants.
For example, am3703 is pin compatible with omap3630, but has sgx and
iva accelerators disabled. We must not try to access the sgx or iva
module registers on am3703, and need to set the unavailable devices
disabled early.
Let's also detect omap3430 as that is needed for display subsystem
(DSS) reset later on, and GP vs EMU or HS devices. Further SoC
specific disabled device detection can be added as needed, such as
dra71x vs dra76x rtc and usb4.
Cc: Adam Ford <aford173@gmail.com>
Cc: André Hentschel <nerv@dawncrow.de>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Pull EFI updates for v5.7 from Ard Biesheuvel:
This time, the set of changes for the EFI subsystem is much larger than
usual. The main reasons are:
- Get things cleaned up before EFI support for RISC-V arrives, which will
increase the size of the validation matrix, and therefore the threshold to
making drastic changes,
- After years of defunct maintainership, the GRUB project has finally started
to consider changes from the distros regarding UEFI boot, some of which are
highly specific to the way x86 does UEFI secure boot and measured boot,
based on knowledge of both shim internals and the layout of bootparams and
the x86 setup header. Having this maintenance burden on other architectures
(which don't need shim in the first place) is hard to justify, so instead,
we are introducing a generic Linux/UEFI boot protocol.
Summary of changes:
- Boot time GDT handling changes (Arvind)
- Simplify handling of EFI properties table on arm64
- Generic EFI stub cleanups, to improve command line handling, file I/O,
memory allocation, etc.
- Introduce a generic initrd loading method based on calling back into
the firmware, instead of relying on the x86 EFI handover protocol or
device tree.
- Introduce a mixed mode boot method that does not rely on the x86 EFI
handover protocol either, and could potentially be adopted by other
architectures (if another one ever surfaces where one execution mode
is a superset of another)
- Clean up the contents of struct efi, and move out everything that
doesn't need to be stored there.
- Incorporate support for UEFI spec v2.8A changes that permit firmware
implementations to return EFI_UNSUPPORTED from UEFI runtime services at
OS runtime, and expose a mask of which ones are supported or unsupported
via a configuration table.
- Various documentation updates and minor code cleanups (Heinrich)
- Partial fix for the lack of by-VA cache maintenance in the decompressor
on 32-bit ARM. Note that these patches were deliberately put at the
beginning so they can be used as a stable branch that will be shared with
a PR containing the complete fix, which I will send to the ARM tree.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The TPD12S015, OPA362 and analog and HDMI connectors are now supported
by DRM bridge drivers, and the omapdrm HDMI and VENC outputs can be
handled through the drm_bridge API. Switch the outputs to drm_bridge by
making the next bridge mandatory and removing the related
omapdrm-specific display drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-40-laurent.pinchart@ideasonboard.com
|
|
The dumb-vga-dac driver can support simple DRM bridges without being
limited to VGA DACs. Rename it to simple-bridge.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-12-laurent.pinchart@ideasonboard.com
|
|
This enables passive cooling by down-regulating CPU voltage
and frequency.
For the trip points, I used values from the BSP code directly.
The critical trip point value is 30°C above the maximum recommended
ambient temperature (70°C) for the SoC from the datasheet, so there's
some headroom even at such a high ambient temperature.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
This enables passive cooling by down-regulating CPU voltage
and frequency.
For trip points, I used a slightly lowered values from the BSP
code. The critical temperature of 110°C from BSP code seemed
like a lot, so I rounded it off to 100°C.
The critical trip point value is 30°C above the maximum recommended
ambient temperature (70°C) for the SoC from the datasheet, so there's
some headroom even at such a high ambient temperature.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
This patch adds the gpio-ranges property to almost all of
the Qualcomm ARM platforms that utilize the pinctrl-msm
framework.
The gpio-ranges property is part of the gpiolib subsystem.
As a result, the binding text is available in section
"2.1 gpio- and pin-controller interaction" of
Documentation/devicetree/bindings/gpio/gpio.txt
For more information please see the patch titled:
"pinctrl: msm: fix gpio-hog related boot issues" from
this series.
Reported-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Tested-by: Sven Eckelmann <sven.eckelmann@openmesh.com> [ipq4019]
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Tested-by: Robert Marko <robert.marko@sartura.hr> [ipq4019]
Cc: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Link: https://lore.kernel.org/r/20200108125455.308969-1-robert.marko@sartura.hr
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
|
|
This kernel configuration is basically enabling/disabling sr driver quirks
detection. While these quirks are for fairly rare devices (very old CD
burners, and a glucometer), the additional detection of these models is a
very minimal amount of code.
The logic behind the quirks is always built into the sr driver.
This also removes the config from all the defconfig files that are enabling
this already.
Link: https://lore.kernel.org/r/20200223191144.726-1-flameeyes@flameeyes.com
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Diego Elio Pettenò <flameeyes@flameeyes.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
i.MX fixes for 5.6:
- Build v7_cpu_resume() unconditionally to fix system hang in case that
suspend is disabled but cpuidle support is enabled.
- Drop unexisting Ethernet PHY device from imx8qxp-mek board.
- Fix SRAM compatible strings on imx6dl-colibri-eval-v3 board.
- Fix imx-scu driver to make sure that all messages words are written
sequentially.
- A series from Leonard Crestez to fix i.MX SC API users, having all
messages aligned on 4 bytes.
- Fix eMMC supply for phycore-som board.
- Drop bogus frequency setting from imx7-colibri SD/MMC device, so that
HS200 mode starts working and delivers better performance.
- Fix opp-supported-hw for i.MX7D to get consumer and industrial parts
work with correct frequency settings.
- Restore MDIO compatible to the correct one for LS1021A SoC.
* tag 'imx-fixes-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx-scu: Align imx sc msg structs to 4
firmware: imx: Align imx_sc_msg_req_cpu_start to 4
firmware: imx: scu-pd: Align imx sc msg structs to 4
firmware: imx: misc: Align imx sc msg structs to 4
firmware: imx: scu: Ensure sequential TX
ARM: dts: imx7-colibri: Fix frequency for sd/mmc
arm64: dts: imx8qxp-mek: Remove unexisting Ethernet PHY
ARM: dts: imx6dl-colibri-eval-v3: fix sram compatible properties
ARM: dts: ls1021a: Restore MDIO compatible to gianfar
ARM: dts: imx7d: fix opp-supported-hw
ARM: imx: build v7_cpu_resume() unconditionally
ARM: dts: imx6: phycore-som: fix emmc supply
Link: https://lore.kernel.org/r/20200224120334.GH27688@dragon
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Fix LCD backlight issue for droid4
There was a bit of an integration glitch with the LED backlight series.
The LED related parts got merged into v5.6-rc1, but the actual backlight
driver got left out.
This caused an issue on at least droid4 where the LCD backlight can not
yet be enabled automatically. And the LCD backlight can no longer be
enabled manually either via sysfs.
The integration glitch happened because some pending comments from me.
There was some confusion on which device tree property we should use for
the default brightness property.
After discussing how to fix this on the mailing lists, we came to the
conclusion that it's best to fix this issue properly by adding the
missing driver.
The other solutions would mean backpedaling and try to come up with some
temporary solution that really does not solve the issue for users. The
patch for led_bl.c has been around for quite a while and tested by many
users and was assumed to be merged as part of the LED backlight series.
For the brightness property to use, we ended up using the more common
"default-brightness-level" rather than "default-brightness" used by
some backlight drivers.
* tag 'omap-for-v5.6/droid4-lcd-fix-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: droid4: Configure LED backlight for lm3532
backlight: add led-backlight driver
Link: https://lore.kernel.org/r/pull-1582303901-96693@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
We are missing AESS for omap5. Looks like it's similar to what we have
for omap4, and this gets ti-sysc interconnect target module driver to
detect it properly.
Note that we currently have no child device driver available for it.
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Tested-by: Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The "renesas,rcar-sata" compatible value was deprecated by
"renesas,sata-r8a7779" many years ago, in commit e67adb4e669db834
("sata_rcar: Add R-Car Gen2 SATA PHY support"). Drop it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20200219153929.11073-1-geert+renesas@glider.be
|
|
Add reset control properties to the devices node for the Display Units
on all supported RZ/G1 SoCs. Note that on these SoCs, there is only a
single reset for all DU channels.
Join the clocks lines while at it, to increase uniformity.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200218133019.22299-3-geert+renesas@glider.be
|
|
Add reset control properties to the device nodes for the Display Units
on all supported R-Car Gen2 SoCs. Note that on these SoCs, there is
only a single reset for all DU channels.
Join the clocks lines while at it, to increase uniformity.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200218133019.22299-2-geert+renesas@glider.be
|
|
The DU DT bindings have been updated to drop the reg-names property.
Update the r8a7745 device tree accordingly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20200218132217.21454-1-geert+renesas@glider.be
|
|
USB-ID signal has a pullup on the schematic, but in reality it's not
pulled up, so add a GPIO pullup. And we also need a usb0_vbus_power-supply
for VBUS detection.
This fixes OTG mode detection and charging issues on TBS A711 tablet.
The issues came from ID pin reading 0, causing host mode to be enabled,
when it should not be, leading to DRVVBUS being enabled, which disabled
the charger.
Fixes: f2f221c7810b824e ("ARM: dts: sun8i: a711: Enable USB OTG")
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
Lowering the voltage solves the quick image degradation over time
(minutes), that was probably caused by overheating.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
Property dr_mode = "otg" is the default in sun8i-a83t.dtsi
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
What works:
- Serial console
- mmc0, mmc2 (both microSD card slots on the board)
- All buttons (gpio and lradc based)
- Power LED
- PMIC
- RTC
- USB OTG/gadgets mode
- Realtek USB WiFi
- Display backlight
- eInk display SPI NOR flash memory
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
Node name should be generic, use "ocotp-ctrl" instead of "ocotp"
for all i.MX6 SoCs.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Node name should be generic, use "watchdog" instead of "wdog" for
wdog nodes.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for the Toradex Aster carrier board.
Follow the usual hierarchic include model, maintaining shared
configuration imx7-colibri-aster.dtsi.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Replace boiler plate licenses texts with the SPDX license identifiers in
Colibri iMX7 DTS files.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
SD/MMC on Colibri iMX7S/D modules successfully support
200Mhz frequency in HS200 mode.
Removing the unnecessary max-frequency limit significantly
increases the performance:
== before fix ====
root@colibri-imx7-emmc:~# hdparm -t /dev/mmcblk0
/dev/mmcblk0:
Timing buffered disk reads: 252 MB in 3.02 seconds = 83.54 MB/sec
==================
=== after fix ====
root@colibri-imx7-emmc:~# hdparm -t /dev/mmcblk0
/dev/mmcblk0:
Timing buffered disk reads: 408 MB in 3.00 seconds = 135.94 MB/sec
==================
Fixes: f928a4a377e4 ("ARM: dts: imx7: add Toradex Colibri iMX7D 1GB (eMMC) support")
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Now that we have added new ways to load the initrd or the mixed mode
kernel, we will also need a way to tell the loader about this. Add
symbolic constants for the PE/COFF major/minor version numbers (which
fortunately have always been 0x0 for all architectures), so that we
can bump them later to document the capabilities of the stub.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
The fixed regulators defined for Arndale5250 boards have no control lines,
so mark them as 'always-on' to better describe the hardware and also kill
the strange messages like 'MAIN_DC: disabling' after boot.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
According to the schematic, both eMMC and SDMMC use dedicated fixed
regulators connected directly to the DC5V and MAIN_DC rails. Remove the
GPX1-1 line assigned to the MMC regulator, because such control
connection doesn't exist. Also change its name to VDD_MMC to avoid
conflict with LDO18 output of S5M8767 PMIC.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Expose efi_entry() as the PE/COFF entrypoint directly, instead of
jumping into a wrapper that fiddles with stack buffers and other
stuff that the compiler is much better at. The only reason this
code exists is to obtain a pointer to the base of the image, but
we can get the same value from the loaded_image protocol, which
we already need for other reasons anyway.
Update the return type as well, to make it consistent with what
is required for a PE/COFF executable entrypoint.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
In preparation for turning the decompressor's cache clean/flush
operations into proper by-VA maintenance for v7 cores, pass the
start and end addresses of the regions that need cache maintenance
into cache_clean_flush in registers r0 and r1.
Currently, all implementations of cache_clean_flush ignore these
values, so no functional change is expected as a result of this
patch.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
The EFI stub executes within the context of the zImage as it was
loaded by the firmware, which means it is treated as an ordinary
PE/COFF executable, which is loaded into memory, and cleaned to
the PoU to ensure that it can be executed safely while the MMU
and caches are on.
When the EFI stub hands over to the decompressor, we clean the caches
by set/way and disable the MMU and D-cache, to comply with the Linux
boot protocol for ARM. However, cache maintenance by set/way is not
sufficient to ensure that subsequent instruction fetches and data
accesses done with the MMU off see the correct data. This means that
proceeding as we do currently is not safe, especially since we also
perform data accesses with the MMU off, from a literal pool as well as
the stack.
So let's kick this can down the road a bit, and jump into the relocated
zImage before disabling the caches. This removes the requirement to
perform any by-VA cache maintenance on the original PE/COFF executable,
but it does require that the relocated zImage is cleaned to the PoC,
which is currently not the case. This will be addressed in a subsequent
patch.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
Stefan Wahren
Olof Johansson
Suman Anna
Dave Gerlach
Tony Lindgren
Mans Rullgard
Ard Biesheuvel
Marek Szyprowski
Faiz Abbas
Kishon Vijay Abraham I
Ingo Molnar
Laurent Pinchart
Ondrej Jirman
Christian Lamparter
Diego Elio Pettenò
Geert Uytterhoeven
Anson Huang
Oleksandr Suvorov